Filters
total: 8109
filtered: 6492
displaying 1000 best results Help
Search results for: destroyed joints, welded joints, steel structure, accelerations, earthquakes, shaking table tests
-
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublicationThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
Axial capacity of steel built-up battened columns
PublicationThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Possibilities for assesment of the angular distortion in Welded T-joint
PublicationSpawanie jest podstawową techniką łączenia elementów konstrukcji kadłuba statku. Procesowi temu towarzyszą odkształcenia spawalnicze, co przysparza dużo problemów wykonawczych. W pracy przedstawiono wpływ przewymiarowania spoiny pachwinowej na wielkość kątowych odkształceń złącza. Dokonano porównania wartości określonych na podstawie inżynierskich hipotez z wynikami otrzymanymi podczas prób laboratoryjnych.
-
Calculations of notch stress factor of a thin-walled spreader bracket fillet weld with the use of a local stress approach
PublicationPresence of geometric notches in welded joints causes concentration of strains and stresses, therefore reducing fatigue strength of such joints. This article presents an analysis of stress concentrations in a fillet weld of a spreader mounting bracket on a small sailing yacht. The aim of this article is to direct the attention of designers, manufacturers and regulatory bodies to issues of fatigue cracks that form in brackets fastening...
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
PublicationThe aim of the paper is the application of guided waves in the evaluation of a condition state of adhesive connection between steel and concrete. The study concerns a push-out specimen consisting of two steel plates glued to opposite faces of a concrete cube with the use of structural adhesive. Wave propagation in the specimen without external load is investigated both experimentally and numerically. The second stage of the investigation...
-
Effect of Base-Connection Strength and Ductility on the Seismic Performance of Steel Moment-Resisting Frames
PublicationColumn-base connections in steel moment-resisting frames (SMFs) in seismic regions are commonly designed to develop the capacity of adjoining column with an intent to develop a plastic hinge in the column member, rather than in the connection (i.e., a strong-base design). Recent research has shown base connections to possess high ductility, indicating that this practice may be not only expensive but also unnecessary. This suggests...
-
Surface treatment of C80U steel by long CO2 laser pulses
PublicationThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Modal analysis of cylindrical steel tanks
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is crucial because any failure could have serious consequences. The aim of present paper is to show the results of the first phase of investigation of seismic behaviour such structures. Modal analysis using Finite Element Method (FEM) for three models of real tanks used in Poland has...
-
Behaviour of Colliding Multi-Storey Buildings under Earthquake Excitation Considering Soil-Structure Interaction
PublicationThis paper investigates the coupled effect of the supporting soil flexibility and pounding between neighbouring, insufficiently separated buildings under earthquake excitation. Two adjacent three-storey structures, modelled as inelastic lumped mass systems with different structural characteristics, have been considered in the study. The models have been excited using the time history of the Kobe earthquake of 1995. A nonlinear...
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublicationsettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
Model tests of cast-in-place piles formed by using different types of auger
PublicationModel tests are still a popular research tool used to observe and determine the mechanisms of pile-soil interaction. Due to the significant scale effect, the results of model tests performed in the 1g system can only be analysed from the qualitative side. This article describes and presents the results of 1g pile model tests carried out for comparative purposes. There were tested the effectiveness and efficiency of various types...
-
Temper bead welding of S460N steel in wet welding conditions
PublicationWet welding is the most common method of welding in water environment. It is most often used for repairing of underwater parts of offshore structures. However, the water as a welding environment causes an increase of susceptibility of steels to cold cracking. For underwater constructions high strength low alloy (HSLA) steel are widely used. In wet welding condition a HSLA steel is characterized by high susceptibility to cold cracking....
-
Modal analysis of temporary steel grandstand equipped with different bracing systems
PublicationThe aim of this paper is to present the results of numerical analysis focused on temporary steel scaffolding grandstand. The investigation has been devoted to modal analysis where modes of free vibrations and corresponding natural frequencies have been estimated and compared. The structure was equipped with different types of stiffener members. One on them is a typical tubular stiffener, while the second one is spe-cially designed...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublicationFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
Earthquake-Induced Pounding Between Asymmetric Steel Buildings
PublicationEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phenomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Importance of model tests in design and operation of watercraft for example CTO
PublicationShip Hydromechanics Division is a specialized research and development department of Ship Design and Research Centre conducting tests and research in the field of hydromechanics, connected with design and operation of ships and other floating structures, in scope of: predictions, numerical analyses, designs of - hull shape optimized with respect to the ship’s functions with the application of modern design tools, screw propellers...
-
Reduction of steel chimney vibrations with a pendlum damper.
PublicationKarman vortices observed around chimneys may induce dangerous structural vi-brations at certain wind velocities. The aim of this paper is to analyse theeffectiveness of pendulum damper in vibration reduction of a steel chimney. A two degree-of-freedom system is used to model the behaviour of the struc-ture equipped with a damper. The results of the study show that the use of pendulum with tuned frequency leads to significant...
-
Novel method of estimation of inertial and dissipative parameters of a railway pantograph model
PublicationAn increase in electric railway vehicles service velocity requires that correct interaction between the pantograph and the catenary is ensured. This implies the need for developing mathematical models of pantographs and catenaries and determining their parameters. The article presents a method to determine parameters of mechanical joints of a railway pantograph based on analysis of pantograph subassemblies in swinging motion. The...
-
Shaft friction from the DMT and direct shear interface tests
PublicationThe article presents preliminary attempt to create tri-linear transfer curves for describing pile behaviour under axial loading. Transfer curves would use the parameter measured in dilatometer test, particularly a constrained modulus MDMT. The proposed method is based on concrete rough and smooth interface tests performed in a direct shear apparatus. Based on the obtained mobilization curves, relationships were created between...
-
Earthquake-induced pounding between asymmetric steel buildings
PublicationEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublicationThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
Ranking of ecotoxisity tests for underground water assessment using the Hasse diagram technique
PublicationThe present study deals with the novel application of the Hasse diagram technique (HDT) for the specific ranking of ecotoxicity tests capable of assessment of underground water quality. The area studied is a multi-municipal landfill in the northern Poland. The monitoring network of the landfill constitutes of 27 piezometers for underground water monitoring and two observation points at surface water courses. After sampling, chemical...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublicationThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
A New Adaptive Method for the Extraction of Steel Design Structures from an Integrated Point Cloud
PublicationThe continuous and intensive development of measurement technologies for reality modelling with appropriate data processing algorithms is currently being observed. The most popular methods include remote sensing techniques based on reflected-light digital cameras, and on active methods in which the device emits a beam. This research paper presents the process of data integration from terrestrial laser scanning (TLS) and image data...
-
Numerical analysis and in situ tests of the Grot Rowecki Bridge in Warsaw
PublicationThe paper presents the FEM analysis of the reconstructed the Grot-Rowecki Bridge over Vistula river in Warsaw. The bridge has seven spans and consists of two independent structures with the longest spans of 120 m. After reconstruction the bridge is over 10 m wider. The numerical, nonlinear analysis has been con-ducted on a global and local FEM models. These models are defined so as they strictly comply with global structural bridge...
-
Modal Adjustment of Rayleigh Based Structural Damping and Coordinate-Partitioning Algorithm Dedicated to Frictionless Contact Constraints between Multibody System and Structure Modelled with Finite Elements
PublicationThe paper presents a dedicated numerical algorithm. The algorithm is advantageous during investigations of the dynamics of a hybrid multibody / finite-elements system. We focus our attention on interactions resulting from mechanical contact. Pointwise contact connects a vertex of the multibody structure and a surface of the elastic reference body. Instead of a positive value of the relative penetration factor, constraint equations...
-
Dynamic analysis of temporary steel grandstand subjected to human-induced excitations due to jumping
PublicationSteel grandstands are structures that are frequently used during sport games and many other non-sporting events, such as festivals, music concerts, or even politicians rallies, with participation of a large number of attendees. Unfortunately, the presence of unexpected excessive dynamic loads due to unpredictable behaviour of spectators (e.g. synchronized harmonic jumping or swaying) may lead to...
-
Comparison of the tests for equivalence of the measurement methods for measurement of PM10 dust in ambient air
PublicationThe paper presents the motives for conducting the equivalence tests and the reasons of discrepancies between the results of PM10 dust concentration obtained via the reference method and the methods based on 'on-site' measurement. The reference and non-reference methods of measurement of PM10 dust concentration in air have been discussed. Field tests for equivalence, following the Polish standard and the European Union (EU) guidelines,...
-
Stresses in the zone of process openings in the shell of a vertical cylindrical steel tank
PublicationW dolnej części płaszcza zbiornika walcowego na ciecze konieczne jest wykonanie różnego rodzaju otworów technologicznych. Artykuł poświęcony jest analizie stanu naprężeń w strefie wzmocnień wykonywanych w sąsiedztwie otworów na rurociągi oraz na włazy wyczystkowe w płaszczu zbiornika. Ponieważ charakter zmian naprężeń, a więc i wzmocnień w strefie obu rodzajów otworów jest różny dlatego artykuł podzielony jest na dwie części, z...
-
Experimental and numerical study on stability loss of innovative geometry steel girder
PublicationThis paper presents the experimental and numerical analysis of an innovative plate girder geometry with variable web thicknesses. An idea proposed in this research is to increase the stability of the girder web by increasing its thickness in the compressed zone. This solution can replace commonly used longitudinal stiffeners which are designed to prevent web local loss of stability. Moreover, such an innovative approach requires...
-
Consequences of New Approach of Chemical Stability Tests of Active Pharmaceutical Ingredients (APIs)
PublicationThere is a great need of broaden look on stability tests of active pharmaceuticalingredients (APIs) in comparison with current requirements contained in pharmacopeia.By usage of many modern analytical methods the conception of monitoring the changesof APIs during initial stage of their exposure to harmful factors has been developed. Newknowledge must be acquired in terms of identification of each degradation...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublicationThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...
-
The effect of polyamide PA12 and polyester PBT blocks' lengths on the structure and propertries of multiblock terpoly(amide-block-ester-block-amide) (TPAEA)
PublicationThe ternary multiblock system terpoly(amide-b-ester-b-amide) (TPAEA) of the chemical structure: poly[(oligoamide-6.36)-block-(tetramethylene terephthalate)-block-laurolactam)] -(PA6.36-b-PBT-b-PA12)n- has been obtained (Table 1). In this system the third component (PBT block here), characterized with the proper molecular weight, is dissolved in hard phase of PA12 blocks and partially dissolved in soft phase of PA6.36. The effects...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublicationThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublicationPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
Corrosivity of environment and the current state of the steel elements at the former Auschwitz concentration camp
PublicationThe objective of this study was to assess corrosivity of the atmospheric environment in the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp, and to identify the protective properties of existing corrosion products in order to estimate the actual corrosion rate of original steel elements located there. The current atmospheric corrosivity of the former Auschwitz camp, specified during one year of exposure...
-
Assessment of crack resistance of S355J2+N steel according to SEP 1390 standard
PublicationThe aim of the study was to evaluate the weldability of S355J2+N steel by bending test according to SEP 1390. In the specimen from S355J2+N steel 3 external cracks were found, 1 of which were stopped in the fusion line and 2 in heat affected zone. Results of bending test for investigated grade of steel are positive.
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Tensile validation tests with failure criteria comparison for various GFRP laminates
PublicationThe paper studies the mechanical properties of glass fibre reinforced polymers (GFRP) with various types and orientation of reinforcement. Analyzed specimens manufactured in the infusion process are made of polymer vinyl ester resin reinforced with glass fibres. Several samples were examined containing different plies and various fibres orientation [0, 90] or [+45, –45]. To assess the mechanical parameters of laminates, a series...
-
Complexes of silanethiolate ligands: Synthesis, structure, properties and application
PublicationThe purposeful syntheses of silanethiolate complexes started approximately in the mid-eighties of the 20th century but no summary of the synthetic efforts has been reported till now. The synthetic methods and the resulting complexes have some common features, which are emphasized throughout the review. Thereby specific difficulties during synthesis are outlined and the structures, properties and possible applications of the resulting...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublicationThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
Influence of fasteners and connections flexibility on deflections of steel building including the stressed skin effect
PublicationThe paper presents the analysis of the influence of fasteners and connections flexibility on displacements of symmetrical single-bay pitched-roof steel building, including trapezoidal cladding acting as a diaphragm. The purpose of the article was to compare numerical models with and without taking into consideration fasteners and connections flexibility in order to observe the differences in transverse stiffness of the building...
-
UPDRS tests for diagnosis of Parkinson's disease employing virtual-touchpad
PublicationThis paper presents a new approach to diagnosing Parkinson's disease. The progression of the disease can be measured by the UPDRS (Unified Parkinson Disease Rating Scale) scale which is used to evaluate motor and behavioral symptoms of Parkinson's disease. Hitherto the evaluation of the advancement of the disease in the UPDRS scale was made by a specialist through medical observation. The authors suggest a partial automation of...
-
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublicationCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
Establishing Relationships between Parameters of the controlled Compaction Soil by Using Various In-Situ Tests
PublicationThe aim of research was evaluating reliable correlations between chosen soil parameters describing state of surface layers of soil. The paper presents site comparative tests based on the light falling weight deflectometer (LFWD), the static plate load tester (VSS), the dynamic probing light tester (DPL) and the bearing ratio tester (CBR in-situ) with relationships between soil state parameters. All featured in-situ...