Search
Filters
total: 1430
filtered: 489
Search results for: diabetes mellitus
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublicationThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Application of spectroscopy to the measurement of blood parameters
PublicationSpectroscopy is the study of formation and interpretation of the spectra arising from the interactions of all types of radiation on matter, understood as a collection of atoms and molecules. This is a very important department of optics which gives us many opportunities to measure various parameters such as material blood parameters. Among the diseases that are associated significantly with changes in rheological properties of...
-
Influence of synthesis conditions on zinc oxide nanorode layer morphology
PublicationIn recent years one dimensional (1D) nanostructures (nanotubes, nanowires, nanoribbons and nanorods) have been widely studied. Among studied nano-materials, the greatest interest can be seen for zinc oxide (ZnO). However, there is still a need for simple, inexpensive and reproducible fabrication method. In the literature different fabrication methods can be found, most of them requires expensive equipment and involve complex...
-
Fiber-optic Fabry-Pérot sensors – modeling versus measurements results
PublicationThis paper describes how parameters of investigated substances and the fiber-optic Fabry-Pérot sensing interferometer affect the spectrum of the optical radiation at the output of the sensor. First, the modeling of the operation of the sensing interferometer was conducted. Most important parameters and effects that were taken into account are: dependences of the refractive indices of the core and the cladding, as well the mode...
-
Non-invasive blood glucose monitoring with Raman spectroscopy: prospects for device miniaturization
PublicationThe number of patients with diabetes has reached over 350 million, and still continues to increase. The need for regular blood glucose monitoring sparks the interest in the development of modern detection technologies. One of those methods, which allows for noninvasive measurements, is Raman spectroscopy. The ability of infrared light to penetrate deep into tissues allows for obtaining measurements through the skin without its...
-
Ocena pracy dźwigara zadaszenia Hali Blanika w Gdańsku
PublicationWartykule przedstawiono kompleksowe sprawdzenie nośności stalowej konstrukcji zadaszenia Hali Leszka Blanika w Gdańsku. Dokonano oceny wpływu otworów dużej średnicy w środnikach dźwigara na jego nośność. Oszacowano nośność nietypowego, zginanego styku doczołowego łączącego elementy dwuteowe klasy 4. Obliczenia wykonano na podstawie norm i analiz modeli MES.
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublicationThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Dynamics of fault arc traveling along busbars in high voltage switchboards = Dynamika łuku zwarciowego przemieszczającego się wzdłuż szyn rozdziel-nic wysokiego napięcia
PublicationThe paper presents the results of magnetic induction and electrodynamic force calculations acting on arc column during short-circuit in medium voltage air-insulated bus-bars. The gap between the bars was 120 mm and the prospective short-circuit currents ranged from 4 kA to 8 kA. The paper also shows the measurement results of average velocity fault arc depending on currents arc diameter and arc current was established and described....
-
Study on effective front region thickness of PCM in thermal energy storage using a novel semi-theoretical model
PublicationThermal energy storage in mobile applications, particularly battery of electric vehicles, is currently gaining a lot of importance. In this paper, a semi-theoretical time-dependent mathematical model of the phase change in a double shell thermal energy storage module has been developed where the inner tube is a heat exchange surface. An effective front region thickness for the melting and solidification process has been studied....
-
Size effect in concrete under splitting tension
PublicationThe size effect is a fundamental phenomenon in concrete materials. It denotes that both the nominal structural strength and material ductility always decrease with increasing element size under tension. In the paper splitting tensile tests on cylindrical concrete specimens with the different diameter were carried out. Two types of the loading strip (plywood board and steel cylinder) were used. The concrete strength and ductility...
-
Badania wytrzymałościowe zgrzein łączących pręty zbrojeniowe o średnicy Ø30mm
PublicationZakres badań dotyczy oceny wytrzymałościowej zgrzein doczołowych, wykonanych metodą zwarciową. Elementami zgrzewanymi były pręty zbrojeniowe o średnicy Ø30mm. Badania związane są z okresową kontrolą stabilności parametrów zgrzewarki, szczególnie w odniesieniu do górnych, dopuszczalnych przez producenta zakresów parametrów zgrzewania oraz analizą wyników i porównaniu rezultatów prób wytrzymałościowych uzyskanych w 2019 i 2020 w...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublicationThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
A method for a comprehensive lipidomic analysis of flaxseed (Linum usitatissimum) with the use of LC–Q-TOF-MS and dispersive micro-solid-phase (μDSPE) extraction
PublicationFlaxseed (FS) is one of the richest sources of α-linolenic acid oil and lignans, and it is suggested that the consumption of flaxseed may contribute to the prevention of certain chronic diseases such as many types of cancer, diabetes, cardiovascular diseases and cerebrovascular stroke. Here, we demonstrate a new method for comprehensive FS lipidome profiling with the use of LC–Q-TOF-MS and dispersive micro-solid-phase extraction....
-
Performance of the domestic micro ORC equipped with the shell-and-tube condenser with minichannels
PublicationIn this paper, the original compact shell-and-tube heat exchanger with circular minichannels of in-house design and manufacturing is presented as the condenser for the domestic micro heat and power plant investigations as well as other future technical applications. The heat exchanger is equipped with turbulizing baffles inside the shell. The shell itself is made of a tubular sleeve having an inner diameter of 0.067 m and the length...
-
Influences of grain shape and size distribution on permeability
PublicationThe present study investigates the effects of shape and size distributions of grains on the coefficient of permeability (k). A series of constant head permeability tests were performed to characterize the coefficient of permeability. Three particle size ranges (4.75- 0.075, 1.18- 0.075 and 0.300-0.075 mm) of two different sands (Narli Sand, Crushed Stone Sand) having different shapes were tested in a constant head permeability...
-
Brownian Motion in Optical Tweezers, a Comparison between MD Simulations and Experimental Data in the Ballistic Regime
PublicationThe four most popular water models in molecular dynamics were studied in large-scale simulations of Brownian motion of colloidal particles in optical tweezers and then compared with experimental measurements in the same time scale. We present the most direct comparison of colloidal polystyrene particle diffusion in molecular dynamics simulations and experimental data on the same time scales in the ballistic regime. The four most...
-
Higher responsiveness to rosuvastatin in polygenic versus monogenic hypercholesterolaemia: a propensity score analysis
PublicationBackground The underlying monogenic defect in familial hypercholesterolemia (FH) can be detected in ∼40% of cases. The majority of mutation-negative patients have a polygenic cause of high LDL-cholesterol (LDL-C) due to having inherited a greater than average number of common LDL-C raising single nucleotide polymorphisms (SNPs). Purpose We sought to investigate, whether the monogenic or polygenic defect in FH is associated with...
-
Problems with modelling the strength properties of sailing vessels rigging ropes
PublicationThis article presents the basic parameters of soft ropes: natural fibre ropes, soft wire ropes and synthetic fibre ropes used for running rigging. There are only several materials still used for the production of natural fibre ropes, including cotton, jute, hemp, sisal and manila hemp. The most commonly used soft wire ropes are twisted pair ropes; for smaller diameters there is a 6x19M - FC rope and for larger diameters – 6x37M...
-
Initial Investigation of Wave Interactions During Simultaneous Valve Closures in Hydraulic Piping Systems
PublicationThe effects of interference of pressure waves in simple piping systems were studied. A freeware computer code Allievi developed at the University of Valencia was used to simulate dynamic waveforms in simple and complex networks. The tests were carried out according to three scenarios. No pressure increases significantly exceeding the Joukowsky pressure in simple cases were noticed. When the effects of the simultaneous closing of...
-
Shaping of the workpiece surface in single-disc lapping
PublicationShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Effect of long term service at elevated temperatures on mechanical properties of Manaurite XM reformer tubes
PublicationMicrostructure transformations occur in the Manaurite XM cast steel tubes during long-term operation in the reformer furnace were revealed and described. The rela tionship between mechanical properties, an increase of internal diameter of the tube and microstructure degradation is discussed. Static tensile test was performed on two types of samples with different shapes. It has been shown differences in the results of tests...
-
Mitochondrial DNA copy number and trimethylamine levels in the blood: New insights on cardiovascular disease biomarkers
PublicationAmong cardiovascular disease (CVD) biomarkers, the mitochondrial DNA copy number (mtDNAcn) is a promising candidate. A growing attention has been also dedicated to trimethylamine-N-oxide (TMAO), an oxidative derivative of the gut metabolite trimethylamine (TMA). With the aim to identify biomarkers predictive of CVD, we investigated TMA, TMAO, and mtDNAcn in a population of 389 coronary artery disease...
-
Electrohydrodynamic flow patterns and collection efficiency in narrow wire-cylinder type electrostatic precipitator
PublicationRecently, narrow electrostatic precipitators (ESPs) have become a subject of interest because of their possible application for the cleaning of the exhaust gases emitted by diesel engines. Diesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are not enough effective or very expensive. Therefore,...
-
Distinguishing views in symmetric networks: A tight lower bound
PublicationThe view of a node in a port-labeled network is an infinite tree encoding all walks in the network originating from this node. We prove that for any integers n ≥ D ≥ 1, there exists a port-labeled network with at most n nodes and diameter at most D which contains a pair of nodes whose (infinite) views are different, but whose views truncated to depth Omega( D log(n/ D )) are identical.
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL -MICROJET TEST PROBE
PublicationAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the flow hydraulic diameter to an increase in the economy of cooling and improves its quality (Mikielewicz and Muszyński 2009). Present study describes research results related to the design and construction of the test stand for hybrid microjet- microchannel cooling modules study, which may be applied in...
-
Influence of concentration on contact angle of water-Cu nanofluid on glass substrate
PublicationIn the paper the results of an experimental investigation of influence of nanoparticle concentration on contact angle of water-Cu nanofluid on glass substrate have been presented. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. In the present study copper was applied as nanoparticle while distilled, deionized water was used as a base fluid. The mean diameter of nanoparticle is estimated to be 50...
-
Application of the laser diode with central wavelength 975 nm for the therapy of neurofibroma and hemangiomas
PublicationThis paper presents newly developed dermatological laser (with central wavelength 975 nm) for application in therapies requiring deep penetration of tissue, e.g. cutaneous (dermal) neurofibroma (Recklinghausen disease) and hemangiomas. This laser can work either in pulse or continues wave mode. Laser radiation is transmitted toward the application region by optical fiber with a diameter of 0.6 mm. The compact design of the laser...
-
Sampling Procedures in Studies of Cloud Water Composition: A Review
PublicationThe authors set out and classify the principles of operation of known types of cloud water collectors, and critically review their advantages and drawbacks. Analysis of the literature has yielded information on the parameters of various type of collectors—sampling time, the type of cloud from which the water sample was taken, droplet diameter collected with 50% efficiency (cut off), sample analytes/ parameters determined, types...
-
Powikłania po rekonstrukcji piersi: problem zakażeń i strategii prewencyjnej - przegląd literaturowy
PublicationW niniejszej pracy przedstawiono dane dotyczące powikłań po rekonstrukcji piersi. Manuskrypt ma na celu usystematyzowanie wyników badań z ostatnich lat wraz z aspektami, takimi jak: częstotliwość występowania powikłań oraz ich rodzaj, czynniki predysponujące, a także możliwości profilaktyki. Przeanalizowano dane literaturowe z ogólnie dostępnych artykułów z okresu ostatnich pięciu lat, ze szczególnym uwzględnieniem zakażeń. Do...
-
Elastic Fender-Dolphin Interaction for Economic Design of Berthing Dolphins
PublicationThe study addresses the question of the possible design benefits when considering the interaction between a modern marine modular rubber fender and a steel tubular pile substructure of a berthing dolphin. Absorption of the berthing kinetic energy of the vessel by a dualelasticity pile-fender berthing system is described in detail using the interactive treatment method (ITM). Application of the ITM is illustrated by a calculative...
-
Ordered TiO2 nanotubes with improved photoactivity through self-organizing anodization with the addition of an ionic liquid: effects of the preparation conditions
PublicationModifying the geometric and surface parameters of oriented TiO2 nanotubes (NTs) is beneficial to the utilization of solar energy for chemical reactions, and this performance may be further improved. Thus, the effects of adding an ionic liquid (IL), 1-butylpiridinium chloride [BPy][Cl], and the effects of the water content and preparation conditions on the surface morphological, physicochemical, photocatalytic and photoelectrochemical...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublicationNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
On Computing Curlicues Generated by Circle Homeomorphisms
PublicationThe dataset entitled Computing dynamical curlicues contains values of consecutive points on a curlicue generated, respectively, by rotation on the circle by different angles, the Arnold circle map (with various parameter values) and an exemplary sequence as well as corresponding diameters and Birkhoff averages of these curves. We additionally provide source codes of the Matlab programs which can be used to generate and plot the...
-
Parametric method applicable in calculating breakout force and time for lifting axisymmetric objects from seabed.
PublicationThe issue of calculating parameters for lifting objects of axisymmetric shapes from the seabed is studied. The article presents the results of numerical simulation examination of the equation formulated by Foda for the force needed to extricate the object from the seabed depending on soil and water parameters, extrication speed, and object diameter. The simulations were performed within the range of parameters characteristic for...
-
Daily diet containing canned products significantly increases serum concentrations of endocrine disruptor bisphenol A in young women
PublicationNowadays, exposure to environmental factors is considered to be one of the possible causes of several lifestyle diseases, such as obesity, type 2 diabetes, cardiovascular disease, and cancer. Particularly noteworthy are endocrine‑disrupting chemicals (EDCs), which affect the metabolism of hormones and interact with their receptors, thus exerting adverse health effects. One of the most ubiquitous EDC in daily life is bisphenol A...
-
Grain type and size of particulate matter from diesel vehicle exhausts analysed in transmission electron microscopy
PublicationThe aim of this research was to apply a simple and quick method of size and shape characterization by TEM to diesel exhaust particles from large-capacity, high-performance trucks. Particulate matter (PM) samples were collected while the engines were idling. It was found that PM from vehicle exhaust emissions can be divided into three groups: soot, irregular-shaped particles and circular particles. Irregular-shaped particles and...
-
Multicriteria Optimization Approach to Design and Operation of District Heating Supply System over its Life Cycle
PublicationDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). In the paper a method for optimized selection of design and operating parameters of long distance Heat Transportation System (HTS) is proposed. The method allows for evaluation of feasibility and effectivity of heat transportation...
-
Heave Plates with Holes for Floating Offshore Wind Turbines
PublicationThe paper presents an innovative solution which is heave plates with holes. The long-known heave plates are designed to damp the heave motion of platforms. They are most often used for Spar platforms. The growing interest in this type of platform as supporting structures for offshore wind turbines makes it necessary to look for new solutions. Based on the available literature and the authors’ own research, it was concluded that...
-
Analytical methodologies for determination of artificial sweeteners in foodstuffs- a review
PublicationArtificial high-intensity sweeteners are more and more frequently used for food production. Food industry tends to highlight beneficial aspects of their use, such as tooth-friendliness, rising-up quality of life of those suffering from different forms of diabetes and possibility of weight control without sacrificing favorite unhealthy drinks or snacks. On the other hand some of the consumers are deeply concerned about safety of...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
PROBLEMS OF EXPERIMENTAL DETERMINATION OF COEFFICIENTS OF THE WEAR OF SHIP PIPING SYSTEMS
PublicationThe article presents series of considerations relating to experimental evaluation of the reliability of ship piping systems. The aim of this study is to attempt to answer the following questions: What should be the tested element? How to choose the diameter of the tested item? What should be the result of measurements and calculations? How to measure? How to choose the duration of the test? How to choose the sample size and elaborate...
-
Electrochemical and photoelectrochemical properties of the interface between titania nanotubes covered by conducting polymer in aqueous by conducting polymer in aqueous electrolytes – The effect of various geometry and electrolytes concentration
PublicationIn the present work we show the impact of nanotubes (NTs) geometry of titania utilized as a substrate in organic-inorganic systems acting as a p-n junction on efficient conversion of radiation energy into electrochemical energy. The electrolytic bath composition and electrolysis conditions were controlled in order to obtain TiO2NTs of various geometry as a result of electrochemical oxidation of titanium foil. The electrode material...
-
A DFT+U study of carbon nanotubes under influence of a gate voltage
PublicationA possibility of appearance of antiferromagnetic ordering in armchair carbon nanotubes and graphene is studied using density functional theory within a DFT+U approach. It is shown that the Coulomb repulsion between electrons in the -orbitals of graphene would need to reach a threshold value of ,...
-
Influence of electrode geometric arrangement on the operation of narrow circular electrostatic precipitator
PublicationIn this work the influence of electrode geometric arrangement on the operation of a circular electrostatic precipitator (ESP) was investigated using Particle Image Velocimetry (PIV) method. The ESP was a glass circular cylinder (29 mm in diameter, 300 mm long) equipped with a wire discharge electrode and circular-cylinder collecting electrode. The stainless-steel discharge wire electrode (0.23 mm in diameter, 100 mm long) was mounted...
-
Characterization and Filtration Efficiency of Sustainable PLA Fibers Obtained via a Hybrid 3D-Printed/Electrospinning Technique
PublicationThe enormous world demand for personal protective equipment to face the current SARS-CoV-2 epidemic has revealed two main weaknesses. On one hand, centralized production led to an initial shortage of respirators; on the other hand, the world demand for single-use equipment has had a direct and inevitable effect on the environment. Polylactide (PLA) is a biodegradable, biocompatible, and renewable thermoplastic polyester, mainly...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublicationNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Receptor for advanced glycation end‐products: Biological significance and imaging applications
PublicationThe receptor for advanced glycation end-products (RAGE or AGER) is a transmembrane, immunoglobulin-like receptor that, due to its multiple isoform structures, binds to a diverse range of endo- and exogenous ligands. RAGE activation caused by the ligand binding initiates a cascade of complex pathways associated with producing free radicals, such as reactive nitric oxide and oxygen species, cell proliferation, and immunoinflammatory...
-
Optimization of Single-Sided Lapping Kinematics Based on Statistical Analysis of Abrasive Particles Trajectories
PublicationThe chapter presents the influence of selected kinematic parameters on the geometrical results of the single-sided lapping process. The optimization of these parameters is aimed at improving the quality and flatness of the machined surfaces. The uniformity of tool wear was assumed as main optimization criterion. Lapping plate wear model was created and in detail was analyzed. A Matlab program was designed to simulate the abrasive...