Filters
total: 866
filtered: 616
-
Catalog
Chosen catalog filters
Search results for: ELEKTROFOREZA ŻELOWA
-
Low-energy positron scattering from gas-phase benzene
PublicationIn this paper we are presenting calculations of the elastic cross section of positrons with gas-phase benzene for the energy range from 0.25 eV to 9.0 eV. The calculations are done with the molecular R-matrix method for positron-scattering from poly-atomic molecules using a scaling factor to scale the electron-positron interaction. The scaling factor influences the position of the poles of the R-matrix. We adjust the scaling factor...
-
Superconductivity in the intermetallic compound Zr5Al4
PublicationPolycrystalline Zr5Al4 was synthesized using the arc-melting method. Powder X-ray diffraction confirms the previously reported crystal structure of the Ti5Ga4-type P63/mcm with lattice parameters: a = 8.4312(6) A , and c = 5.7752(8) A . Electrical resistivity and low-temperature magnetic susceptibility measurements indicate that Zr5Al4 exhibits superconducting behavior below 2 K. The normalized heat capacity jump at Tc= 1.82 K...
-
Novel Cold Crucible Ultrasonic Atomization Powder Production Method for 3D Printing
Publication: A new powder production method has been developed to speed up the search for novel alloys for additive manufacturing. The technique involves an ultrasonically agitated cold crucible installed at the top of a 20 kHz ultrasonic sonotrode. The material is melted with an electric arc and undergoes pulverization with standing wave vibrations. Several different alloys in various forms, including noble and metallic glass alloys, were...
-
The quality of sewage sludge stabilized for a long time in reed basins
PublicationThe aim of the work was to determine changes of long-term sewage sludge quality stabilized in reed basins from 7-15 years. The following parameters were evaluated: dry matter and organic matter concentration, nitrogen, phosphorus, and selected heavy metal (Cd, Ni, Pb, Cr, Cu, Zn) fractions. The material for the investigations was collected from 4 reed basin systems (utilisated sewage sludge) located in conventional WWTPs in Denmark...
-
Non-linear behaviour of base-isolated building supported on flexible soil under damaging earthquakes
PublicationSeismic isolation is a strategy to reduce damage of structures exposed to devastating earthquake excitations. Isolation systems, applied at the base of buildings, lower the fundamental frequency of the structure below the range of dominant frequencies of the ground motion as well as allow to dissipate more energy during structural vibrations. The effectiveness of the base-isolated buildings in damage reduction has been confirmed...
-
Analysis of the Possibilities of Applying 3D Print Methods for the Needs of Ship-Building Industry
PublicationArticle presents the analysis of applying additive and hybrid manufacturing methods and its impact on dynamic stiffness of prepared samples. Dynamic analysis of the handle bracket specimens consisted in plotting the resonance curves and using these curves to estimate the dynamic stiffness of elements produced with additive manufacturing technology. Authors focused especially on 3D print in Fused Deposiotion Modeling/Fused Filament...
-
Profiling of polar ionogenic metabolites in Polish wines by capillary electrophoresis-mass spectrometry
PublicationThe composition of wine is determined by a complex interaction between environmental factors, genetic factors (i.e., grape varieties), and winemaking practices (including technology and storage). Metabolomics using NMR spec-troscopy, GC-MS, and/or LC-MS has shown to be a useful approach for assessing the origin, authenticity, and quality of various wines. Nonetheless, the use of additional analytical techniques with complementary...
-
Miniaturized, green salting-out liquid–liquid microextraction coupled with GC–MS used to evaluate biogenic amines in wine samples
PublicationMonitoring of the biogenic amines (BAs) content in food products, including wine, is important due to the health and safety of consumers and from the quality control point of view. In a given study, simultaneous derivatization and salting-out liquid–liquid microextraction (SALLME) coupled with GC–MS for BAs determination from wine samples was developed. For the optimization the Box-Behnken design was applied, where three independent...
-
Role of the Synergistic Interactions of Environmental Pollutants in the Development of Cancer
PublicationThere is a growing awareness that the large number of environmental pollutants we are exposed to on a daily basis are causing major health problems. Compared to traditional studies that focus on individual pollutants, there are relatively few studies on how pollutants mixtures interact. Several studies have reported a relationship between environmental pollutants and the development of cancer, even when pollutant levels are below...
-
Tyre/road noise of passenger car tyres, including tyres for electric vehicles - road measurements
PublicationThe paper presents the results from CPX measurements of tyre/road noise performed for selected passenger car tyres, including the tyres especially designed for electric vehicles. The tyres have been measured when rolling on several typical road surfaces in Norway and in Poland. In addition, the tyres have been measured on some very low noise road surfaces, such as a the poroelastic road surface (PERS). The measurement results...
-
Application of ferric chloride for arsenic removal in the integrated process: coagulation/microfiltration
PublicationThe study presents results of using iron coagulation integrated with microfiltration to remove arsenic from water. Tested samples of natural groundwater contained approximately 32 μg/L of arsenic, 0.13 mg/L of iron and 0.085 mg/L of manganese. As a coagulant the aqueous solution of ferric chloride was dosed in portions from 1.0 to 10.5 mg/L. In the research microfiltration membranes with 400 kDa MWCO were used. Tests indicated...
-
Effect of isovalent substitution on microstructure and phase transition of LaNb1−xMxO4 (M=Sb, V or Ta; x=0.05–0.3)
PublicationLaNb1−xMxO4 oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric...
-
IDENTIFICATION OF ODOR OF VOLATILE ORGANIC COMPOUNDS USING CLASSICAL SENSORY ANALYSIS AND ELECTRONIC NOSE TECHNIQUE
PublicationThe paper compares two methods of analysis of odour of volatile organic compounds: classical sensory analysis and electronic nose technique. Eight volunteers participated in the classical sensory analysis investigations, which lasted two weeks. An instrumental odour analysis involved a prototype of 6-sensor electronic nose designed by the authors. The research performed with this device provided higher reproducibility and reliability...
-
Sodium alginate decreases the permeability of intestinal mucus
PublicationIn the small intestine the nature of the environment leads to a highly heterogeneous mucus layer primarily composed of the MUC2 mucin. We set out to investigate whether the soluble dietary fibre sodium alginate could alter the permeability of the mucus layer. The alginate was shown to freely diffuse into the mucus and to have minimal effect on the bulk rheology when added at concentrations below 0.1%. Despite this lack of interaction...
-
Optically transparent boron-doped nanocrystalline diamond films for spectroelectrochemical measurements on different substrates
PublicationFabrication process of optically transparent boron nanocrystalline diamond (BNCD) electrode on silicon and quartz substrate was shown. The B-NCD films were deposited on the substrates using Microwave Plasma Assisted Chemical Vapor Deposition (MWPACVD) at glass substrate temperature of 475 ºC. A homogenous, continuous and polycrystalline surface morphology with high sp3 content in B-NCD films and film thickness depending from substrate...
-
Fast High-Impedance Spectroscopy Method Using SINC Signal Excitation
PublicationIn this paper the method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 Gohm) is evaluated by means of simulation and practical experiment. The method is based on excitation of an object with a sinc signal and sampling response signals proportional to current flowing through and voltage across the measured impedance. The object impedance spectrum is obtained with use of continuous Fourier transform...
-
A comparative analysis of numerically simulated and experimentally measured static responses of a floating dock
PublicationTwo numerical methods, dynamic and static analyses, are proposed to calculate the static responses of a floating dock under different ballast water distributions. Model-scale experimental tests were conducted to compare with these numerical methods. The dynamic analysis includes a 6-degree-of-freedom (6-DOF) model, a hydrostatic force model and a hydrodynamic force model to simulate the dock's freely floating processes. The dock's...
-
The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools
PublicationGrinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results....
-
Wyznaczanie parametrów modelu obwodowego maszyny komutatorowej prądu przemiennego z wykorzystaniem programu polowego Opera3D
PublicationW referacie przedstawiono liniowy model matematyczny silnika komutatorowego z więzami holonomicznymi. Taki model wymaga zastosowania większej liczby stopni swobody, ale umożliwia uwzględnienie asymetrii i zjawisk zachodzących w zestyku ślizgowym. W modelu tym wymagane są macierze indukcyjności, które uwzględniają sprzężenia magnetyczne pomiędzy elementarnymi cewkami. Do wyznaczenia tych macierzy zastosowano program Opera3D. Aby...
-
Efekty płukania przewymiarowanych sieci wodociągowych metodą ukierunkowanego przepływu
Publicationw referacie przedstawiono rezultaty kompleksowego płukania sieci wodociągowej w biłgoraju w 2006 roku metodą ukierunkowanego przepływu. podstawową cechą zastosowanej metody jest realizacja scenariuszy płukania zaplanowanych za pomocą symulacji komputerowej. rozpoznanie symulacyjne parametrów hydraulicznych rurociągów odróżnia tę metodę od tradycyjnego sposobu płukania wodą. oceny skuteczności płukania dokonano na podstawie wyników...
-
Wymiana ciepła-podstawy teoretyczne
PublicationJedną ze współczesnych dziedzin poznawania określonych zjawisk przyrody jest nauka o przenoszeniu energii. Przenoszenie energii między ciałami następuje, między innymi właśnie na sposób ciepła. Wymiana ciepła posiada ogromne znaczenie dla praktyki, ponieważ z jednej strony, daje podstawy do intensyfikacji przebiegu procesów technologicznych w różnych gałęziach przemysłu, a drugiej strony, pozwala racjonalnie dobrać właściwy poziom...
-
SURFACTANTS IN KLODNICA RIVER (KATOWICE, POLAND). PART II. QUATERNARY AMMONIUM COMPOUNDS
PublicationThe paper presents methods of determination of analytes of the cation group (alkyl benzyl dimethyl ammonium (BDDA-C12-C16), alkyl trimethyl ammonium (TMA), hexadecyl piridinium (HP)) in surface water and bottom sediment samples. In the sample preparation phase the solid phase extraction (SPE) or accelerated solvent extraction/ultrasound assisted extraction (ASE/UAE)-SPE technique was used and in the identification phase and quantitative...
-
Material Identification of the Human Abdominal Wall Based On the Isogeometric Shell Model
PublicationThe human abdominal wall is an object of interest to the research community in the context of ventral hernia repair. Computer models require a priori knowledge of constitutive parameters in order to establish its mechanical response. In this work, the Finite Element Model Updating (FEMU) method is used to identify an heterogeneous shear modulus distribution for a human abdominal wall model, which is based on nonlinear isogeometric...
-
Gigantic electro-chemo-mechanical properties of nanostructured praseodymium doped ceria
PublicationSome oxygen defective fluorites are non-Newnham electrostrictors, i.e., the electromechanical response does not depend on their dielectric properties. Here, we show gigantic electrostriction in nanocrystalline 25 mol% praseodymium doped ceria (PCO) bulk ceramics. The material was fabricated with a fieldassisted spark plasma sintering (SPS) process from high-purity nanoscale PCO powders (<20 nm). The SPS process consolidates the...
-
Playback detection using machine learning with spectrogram features approach
PublicationThis paper presents 2D image processing approach to playback detection in automatic speaker verification (ASV) systems using spectrograms as speech signal representation. Three feature extraction and classification methods: histograms of oriented gradients (HOG) with support vector machines (SVM), HAAR wavelets with AdaBoost classifier and deep convolutional neural networks (CNN) were compared on different data partitions in respect...
-
The Influence of LED Lighting Sources on the Nature of Power Factor
PublicationThis article presents measurements of electric power absorbed by a newly built facility for office and scientific research activities. These measurements highlighted the need for compensation of capacitive reactive power—not predicted by the designer—due to the vast use of LED lighting in the facility. The article also describes a reactive power compensation system, designed on the basis of the above-mentioned measurements, and...
-
Fabrication and Crystal Structure of Sol-Gel Deposited BST Thin Films with Compositional Gradient
PublicationIn the present research technology of compositionally graded barium strontium titanate Ba1-xSrxTiO3 thin films deposited on stainless steel substrates by sol-gel spin coating followed with thermal annealing at T = 650°C is reported. Results of thermal behavior of the sol-gel derived powders with compositions used for fabrication of graded structure (i.e. with Sr mole fraction x = 0.5, 0.4 and 0.3) are described. X-ray diffraction...
-
Fast Fading Characterization for Body Area Networks in Circular Metallic Indoor Environments
PublicationWith the increasing development of 5G and Body Area Network based systems being implemented in unusual environments, propagation inside metallic structures is a key aspect to characterize propagation effects inside ships and other similar environments, mostly composed of metallic walls. In this paper, indoor propagation inside circular metallic structures is addressed and fast fading statistical distributions parameters are obtained...
-
Presence and distribution of antibiotic-resistant bacteria in multiphase activated sludge system
PublicationIn total 237 isolates of coliforms (113 strains) and enterococci (124 stains) from influent, mixed liquor in bioreactor and effluent of wastewater treatment plant (WWTP), were isolated on selective media and examined for antibiotic resistance. From 50 to 80% of the coliform strains isolated from the raw and treated sewage were resistant against ceftazidime CAZ, cefuroxim CXM, cefalotin KF and against amoxicillin AML, and only below...
-
Concentration in ICTs sector - cross country analysis
PublicationIn the chapter below, the author present inequalities in sector of new information and communication technologies. Having in mind inequalities we can also discuss concentration issues, and the concentration itself is a problem to which the author refers on first place. The paper is organized as following: first basic measures of concentration are defined, after we can read a discussion referring to concentration in ICTs sector...
-
Determination of SCFAs in water using GC-FID. Selection of the separation system
PublicationIn the present study, an analytical procedure was developed for the determination of short-chain fatty acids (SCFAs) in landfill leachate and municipal wastewater employing injection of aqueous samples to gas chromatograph with flame ionization detector (GC-FID). Chromatographic conditions such as a separation system, injection volume, oven temperature program were investigated and selected. With two columns, one with a polar (polyethylene...
-
Determination of total mercury in raw petrol using cold vapour atomic absorption spectrometry
PublicationPresence of different forms of mercury in petroleum based products may impair the proper operation of the equipment or led to poisoning of automotive catalysts. However much more important problem is environmental pollution with mercury emitted from different types of fossil fuels. Although the average mercury concentration in petroleum based products (automotive fuels) is on the level around 1 ppb, taking into account annual...
-
Optimization of a Fabric Phase Sorptive Extraction protocol for the isolation of six bisphenols from juice pouches to be analysed by high performance liquid chromatography coupled with diode array detector
PublicationFabric Phase Sorptive Extraction (FPSE) combined with high pressure liquid chromatography using to diode array detection (HPLC-DAD) was applied for the simultaneous determination of bisphenols (BPA, BPB, BPC, BPE, BPF, BPS) in juice pouches. The FPSE procedure was optimized with regards to the critical parameters that affect the performance of the method including the selection of the FPSE membrane type and size, adsorption time,...
-
Miniaturized Inline Bandpass Filters Based on Triple-Mode Integrated Coaxial-Waveguide Resonators
PublicationThis work presents a design technique to implement miniaturized cross-coupled bandpass filters in inline physical configurations based on triple-mode resonators. Triple-mode resonances are obtained by using integrated coaxial-waveguide cavity resonators. They consist of two coaxial conducting posts placed in the sidewalls of a rectangular waveguide cavity. In the proposed triplet, a transmission zero (TZ) can be positioned at any...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublicationFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
Thermal boundary conditions to simulate friction layers and coatings at sliding contacts
PublicationA brief review of the thermal boundary conditions specified at sliding interfaces was performed. New thermal boundary conditions were derived aimed at solving problems of sliding with account of surface layers representing friction layers and tribological coatings. Based on the assumption of linear temperature distributions in the surface layers, the proposed conditions enable one to simplify simulations by eliminating the surface...
-
Femtosecond Er-doped fiber laser source tunable from 872 to 1075 nm for two-photon vision studies in humans
PublicationWe report the development of a widely-tunable femtosecond fiber laser system and its application for two-photon vision studies. The source is based on an Er-doped fiber laser with spectral shift up to 2150 nm, followed by a second harmonic generation module to generate a frequency-doubled beam tunable from 872 to 1075 nm. The source delivers sub-230 fs pulses with nearly-constant duration over the entire tuning range, with output...
-
Highly porous nanoberyllium for X-ray beam speckle suppression
PublicationThe speckle suppressor device containing highly porous nanoberyllium is proposed for manipulating with the spatial coherence length and removing undesirable speckle structure during the imaging experiments. We report a special device called the speckle suppressor, which contains the highly porous nanoberyllium plate, compacted from both sides by two beryllium windows. By insertion the speckle suppressor in the X-ray beam it allows...
-
Simultaneous determination of individual isothiocyanates in plant samples by HPLC-DAD-MS following SPE and derivatization with N-acetyl-l-cysteine
PublicationThe procedure for the isothiocyanates (ITCs) determination that involves derivatization with N-acetyl-l-cysteine (NAC) and separation by HPLC was developed. Prior to derivatization, plant ITCs were isolated and purified using solid-phase extraction (SPE). The optimum conditions of derivatization are: 500 μL of isopropanolic eluate obtained by SPE combined with 500 μL of derivatizing reagent (0.2 M NAC and 0.2 M NaHCO3 in water)...
-
Wykorzystanie technologii informatycznych w zarządzaniu przedsięwzięciami informatycznymi
PublicationW rozdziale przedstawiono charakterystykę zarządzania przedsięwzięciami informatycznymi oraz wskazano na przydatność technologii informatycznych w procesach zarządzania przedsięwzięciem. Stan tych technologii ale głównie poziom ich wykorzystania może mieć kluczowe znaczenie w realizacji przedsięwzięć (osiąganiu założonego celu w ramach przyjętych - harmonogramu i budżetu). Stąd też w ramach koncepcji całej pracy dotyczącej zarządzania...
-
Enzymatyczna hydroliza białek mięśniowych kręgosłupów dorsza bałtyckiego
PublicationCelem badań było ustalenie optymalnych warunków odzyskiwania białek mięśniowych z kręgosłupów dorsza bałtyckiego. Hydrolizę enzymatyczną białek mięśniowych prowadzono stosując trypsynę lub alkalazę w stężeniu: 2,5; 5; 10; 15; 20; 30 i 40 mg/g surowca. Reakcję prowadzono w środowisku obojętnym, przez 24 i 48 h. Wszystkie procesy i operacje jednostkowe powadzono w temperaturze 4 st.C. Efektywność enzymatycznej hydrolizy białek mięśniowych...
-
Mieszane przewodnictwo polaronowo-jonowe szkieł tlenkowych
PublicationPrzeanalizowano klasyczny dla szkieł tlenkowych, zawierających jony metali przejściowych, polaronowy mechanizmu transportu ładunku. Uwzględniono wielofononowe oddziaływania polaronu z fononami akustycznymi i optycznymi. Otrzymane zależności wykorzystano do analizy własnych danych doświadczalnych.Zbadano mieszane przewodnictwo polaronowo-jonowe w kilku rodzinach szkieł tlenkowych zawierających tlenki metali przejściowych. Zaobserwowano...
-
Determination of cyanide in urine and saliva samples by ion chromatography with pulsed amperometric detection
PublicationCommonly known as a highly toxic chemical, cyanide is also an essential reagent for many industrial processes. It naturally occurs in plant seeds as a cyanogenic glycosides. Another relatively common mode of cyanide exposure is inhalation of environmental tobacco smoke. This study concerns importance to determine cyanide ion in human biological samples. Urine and saliva samples were collected healthy volunteers exposed to tobacco...
-
Are the short cationic lipopeptides bacterial membrane disruptors? Structure-Activity Relationship and molecular dynamic evaluation
PublicationShort cationic lipopeptides are amphiphilic molecules that exhibit antimicrobial activity mainly against Grampositives. These compounds bind to bacterial membranes and disrupt their integrity. Here we examine the structure-activity relation (SAR) of lysine-based lipopeptides, with a prospect to rationally design more active compounds. The presented study aims to explain how antimicrobial activity of lipopeptides is affected by...
-
Design aspects of a low-cost prosthetic arm for people with severe movement disabilities
PublicationIn this paper the main aspects of mechanical design behind the low-cost prosthetic arm are presented. The fundamentals of a proper design has been defined to obtain functional 3D printed 5 degree of freedom (DOF) prosthesis. The designed prosthetic arm is a part of the hybrid interface with eye tracking movement control. The main focus was to create affordable but usable prosthesis which corresponds in size and weights to the human...
-
Bifractal receiver operating characteristic curves: a formula for generating receiver operating characteristic curves in credit-scoring contexts
PublicationThis paper formulates a mathematical model for generating receiver operating characteristic (ROC) curves without underlying data. Credit scoring practitioners know that the Gini coefficient usually drops if it is only calculated on cases above the cutoff. This fact is not a mathematical necessity, however, as it is theoretically possible to get an ROC curve that keeps the same Gini coefficient no matter how big a share of lowest...
-
Soft X-ray Induced Production of Neutral Fragments in High-Rydberg States at the O 1s Ionization Threshold of the Water Molecule
PublicationDissociation of water molecules after soft X-ray absorption can yield neutral fragments in high-Rydberg (HR) states. We have studied the production of such fragments by field ionization and ion time-of-flight (TOF) spectrometry. Neutral HR fragments are created at all resonances below the O 1s ionization potential (IP) and particularly within 1 eV above the O 1s IP. The latter effect is due to the recapture of the O 1s photoelectrons...
-
Changes on the Surface of the SiO2/C Composite, Leading to the Formation of Conductive Carbon Structures with Complex Nature of DC Conductivity
PublicationSol–gel layers have been the subject of many studies in recent decades. However, very little information exists about layers in which carbon structures are developed in situ. Using the spin-coating method, we obtained thin iron-doped SiO2/C composite films. The results of Raman spectroscopy showed that our samples consisted of graphitic forms and polymers. The latter’s contribution decreases with rising temperature. FTIR and EDS...
-
Influence of rhamnolipids and ionic cross-linking conditions on the mechanical properties of alginate hydrogels as a model bacterial biofilm
PublicationThe literature indicates the existence of a relationship between rhamnolipids and bacterial biofilm, as well as the ability of selected bacteria to produce rhamnolipids and alginate. However, the influence of biosurfactant molecules on the mechanical properties of biofilms are still not fully understood. The aim of this research is to determine the effect of rhamnolipids concentration, CaCl2 concentration, and ionic cross-linking...
-
Reduction of the Velocity Impact on the Magnetic Flux Leakage Signal
PublicationThe velocity effect on the magnetic flux leakage (MFL) signal was investigated in this paper. Experiments were performed for velocity of the MFL tool within the range of 0–2 m/s. The velocity was not constant during each measurement to imitate real operational conditions of the MFL tool. Two components of the leakage were measured, i.e. the tangential to the motion direction (x) and the normal to the investigated surface (z). In...