Filters
total: 2080
filtered: 1664
displaying 1000 best results Help
Search results for: JADE
-
Study of Direct Methanol Fuel Cell Process Dynamics Using Dynamic Electrochemical Impedance Spectroscopy
PublicationA new technique, which was developed to characterize the direct methanol fuel cell under work conditions, has been presented in this paper. The impedance measurements were made using dynamic electrochemical impedance spectroscopy research technique in the galvanostatic mode, using multiple sinusoidal excitation. Obtained results show, that together with an increase of the temperature and working load, the global impedance...
-
Problem of proper decomposition and initialization of acoustic and entropy modes in a gas affected by the mass force
PublicationThe relations connecting perturbations specific for acoustic and entropy modes in an accelerated fluid or in a fluid affected by constant mass force, are derived. They allow to decompose the total vector of perturbations and the overall energy into acoustic and non-acoustic parts uniquely at any instant. In order to do this, three quantities are required, for example total perturbations in entropy, pressure and velocity. The evaluations...
-
Logistical Aspects of Energy Conversion Efficiency in Marine Steam Power Plants in Off-Design Conditions
PublicationThe paper presents logistical aspects of energy conversion efficiency in off-design conditions. The main part of the article is based on results of thermodynamic calculation for large propulsion steam turbine under partial loads. Calculations are made on extended mathematical model of two proposed steam turbine thermodynamic cycles using Stodola’s cone law. The conclusion based on calculation re-sults contains importance of off-design...
-
Thermophysical properties of the phase change material mixtures – preliminary studies on macromolecular hydrocarbons example.
PublicationThe aim of this work is a theoretical and experimental analysis of the macromolecular hydrocarbon mixtures composition and the impact on thermophysical parameters of the phase change materials (PCM) made from these mixtures. The analysis of the current state of knowledge extended by the author’s own studies have been presented. Thermophysical characteristics of the hydrocarbons and their mixtures have been specified, in such a...
-
3D Computer Model of the Hip Joint Cartilage
PublicationThis paper presents 3D computer model of the hip joint cartilage in the ANSYS program. Model is made on the basis of anatomy and collected data on the material constants of bone and cartilage components. Analysis and comparison of biochemical model, viscoelastic and molecular mixed - aggregation serves to facilitate the creation of the next model of reality, which could be used in the design of joint prostheses. The correctness...
-
Application of dynamic impedance spectroscopy to scanning probe microscopy.
PublicationDynamic impedance spectroscopy, designed for measuring nonstationary systems, was used in combination with scanning probe microscopy. Using this approach, impedance mapping could be carried-out simultaneously with topography scanning. Therefore, correlation of electrical properties with particular phases of an examined sample was possible. The sample used in this study was spheroidal graphite cast iron with clearly defined phases...
-
Fitting the mobile device characteristics to the user's hearing preferences
PublicationA method for fitting the mobile computer audio characteristics to the user's hearing preferences is proposed. The process consists of two stages: calibration and dynamics processing. During the calibration phase the user performs a loudness scaling test giving their response regarding the perceived loudness. The dynamics processing made on above basis sets the loudness to the most comfortable level. The processing accounts both...
-
Deduplication of Position Data and Global Identification of Objects Tracked in Distributed Vessel Monitoring System
PublicationVessel monitoring systems (VMS) play a very important role in safety navigation. In most cases, their structure is distributed and they are based on two data sources, namely Automatic Identification System (AIS) and Automatic Radar Plotting Aids (ARPA). Such approach results in several objects identification and position data duplication problems, which need to be solved in order to ensure the correct performance of a given VMS....
-
CLASSIFICATION OF RESTRAINTS IN THE OPTIMIZATION PROBLEM OF A COLD-FORMED PROFILE
PublicationThis work describes the restraints in the optimization problem. This is an important and complicated issue because it requires taking into account a vast range of information related to the design and production. In order to describe the relations of a specific optimization problem, it is essential to adopt appropriate criteria and to collect information on all kinds of restraints, i.e. boundary conditions. The following paper...
-
The validation process of truss model with joint eccentricities
PublicationNowadays, due to the technological reasons in modern lightweight steel trusses, fabricated from cold-formed sections, positive eccentricities appear in the truss nodes, to induce additional forces truss chords. In order to account for the real load-carrying capacity of truss node area the steel structure research was conducted in scale 1:1. As a result of experimental research, the forms of deformation and strains of the walls...
-
DYNAMIC RESPONSE OF FORUM GDANSK STRUCTURE DUE TO RAIL TRAFFIC
PublicationThe paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing...
-
Stability analysis of a road scarp in the Carpathian Mountains and methods of its protection
PublicationThe purpose of the study was to analyse the stability of a road scarp endangered by a landslide and to consider some measures for its stabilization. The potential landslide could unfavourably alter the shape of the slope, thus a religious sanctuary situated above the slope. The present research has resulted in suggestions of possible protection methods, namely, drainage, soil nailing, installation of piles, supporting the scarp...
-
Study of the Flow Dynamics of Surface Water Masses in the Area of the Coastal Gulf of Gdansk
PublicationThe paper describes two methods of predicting the movement of small objects with surface water masses. One of the methods uses graph theory to describe the motion of water masses in port docks. The results of this study were compared to a simulation using the hydrodynamic numerical model M3D. The results obtained in a virtual environment were related to the experiments in the real world. In the coastal area of the Gulf of Gdansk,...
-
Audio Feature Analysis for Precise Vocalic Segments Classification in English
PublicationAn approach to identifying the most meaningful Mel-Frequency Cepstral Coefficients representing selected allophones and vocalic segments for their classification is presented in the paper. For this purpose, experiments were carried out using algorithms such as Principal Component Analysis, Feature Importance, and Recursive Parameter Elimination. The data used were recordings made within the ALOFON corpus containing audio signal...
-
Effects of Road Infrastructure on Pedestrian Safety
PublicationThe objective of the work was to identify risks for pedestrians that involve road infrastructure and roadside and to define how selected elements of geometry and traffic layout affect driver behaviour (speed on approaching pedestrian crossings). The results have helped to formulate recommendations on pedestrian crossing design. The research included an analysis of 2013-2017 statistics to identify the...
-
Hydraulic analysis of causes of washout of Gdynia-Orłowo seashore during the flood in the Kacza river estuary
PublicationIn July 2016 in the Three-city agglomeration a rainfall episode of over a day duration and 150 mm summary rainfall height, occurred. This situation, extreme as for Polish conditions, caused significant freshets in rivers and streams running into Gdansk Bay, the Baltic Sea, and serving as collectors of rainfall waters for the sea-coast towns. In many areas of the Three-city flood phenomena and overflows took place. The flood also...
-
Fatigue of titanium alloy Ti6Al4V with diamond structure obtained by Laser Power Bed Fusion method
PublicationThis paper presents the results of fatigue tests conducted on Ti6Al4V titanium alloy with diamond structure obtained by the Laser Power Bed Fusion method. Samples used in tests were printed with porosities: 81%, 73%, 50%, 34% and near-zero porosity. Samples were subjected to cyclic tests with a constant stress amplitude. The number of cycles until sample failure was registered. Obtained fatigue test results made it possible to...
-
Cast iron in the 19th-century building equipment
PublicationCast iron is a material, characteristics of which enable to receive extremely artistic elements. It maintains good strength properties at the same time. That combination of these seemingly contrary traits makes it a commodity that was widely used in the 19th century industry and architecture. These usages were not only as decorative elements, technical and structural ones. The production of new household utilities started, which...
-
Exploring the Solubility Limits of Edaravone in Neat Solvents and Binary Mixtures: Experimental and Machine Learning Study
PublicationThis study explores the edaravone solubility space encompassing both neat and binary dissolution media. Efforts were made to reveal the inherent concentration limits of common pure and mixed solvents. For this purpose, the published solubility data of the title drug were scrupulously inspected and cured, which made the dataset consistent and coherent. However, the lack of some important types of solvents in the collection called...
-
Towards a multi-basin SWAT model for the migration of nutrients and pesticides to Puck Bay (Southern Baltic Sea)
PublicationBackground This paper analyzes the impact of changes in fertilization on crop yields and the runoff of nutrients from a small agricultural catchment (176 km2) to a shallow bay, using the SWAT model. Puck Bay is part of the Gulf of Gdansk and belongs to the Baltic Sea. The whole area of Puck Bay (364 km2) is protected (Natura 2000) yet despite this it suffers from eutrophication problems due to the relatively minimal depth and...
-
Ukrainian Market of Electrical Energy: Reforming, Financing, Innovative Investment, Efficiency Analysis, and Audit
PublicationThe aim of this research is to determine the influence of electrical energy market regulation reform in Ukraine on the competitive environment, the reproduction processes of financial and innovative support, and the energy efficiency of the national economy. The authors have put forward and verified the hypothesis that, under conditions of institutional maturity of the Ukrainian electrical energy market, its liberalization and...
-
Thermoplastic starch nanocomposites using cellulose-rich Chrysopogon zizanioides nanofibers
PublicationGreen thermoplastic starch (TPS) nanocomposite films aided by cellulose nanofibers (CNFs) from Chrysopogon zizanioides roots were developed and characterized. When compared to other lignocellulosic fibers, Chrysopogon zizanioides roots revealed exceptionally high cellulose content (~48%). CNFs were separated using an environmentally friendly acid isolation technique that included three stages: (i) alkali treatment; (ii) bleaching;...
-
L'industria e la Storia. La lezione di Giorgio Mori
PublicationThe wide contribution of Giorgio Mori for a better understanding of the long-term historical relationships between history and industry is the focus of this chapter. By analysing the long list of books and articles written all along his scientific and academic life it is possible to trace a sort of fil rouge that permits to appreciate the huge effort made by this scholar in offering a fresh and never banal interpretation of the...
-
ENERGY ANALYSIS OF PROPULSION SHAFT FATIGUE PROCESS IN ROTATING MECHANICAL SYSTEM PART I TESTING SIGNIFICANCE OF INFLUENCE OF SHAFT MATERIAL FATIGUE EXCITATION PARAMETERS
PublicationThe article discusses the problem of mathematical modelling of energy conversion processes in a rotating mechanical system for the purpose of identifying fatigue states of propulsion shafts in this system. A simplified physical model of the analysed system, constructed in an appropriate scale, has made the basis for the experimental research. The research programme took into consideration mechanical fatigue excitation of the model...
-
Sustainable utilization of copper post-flotation waste in cement composites
PublicationThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
The fracture behaviour of notched PMMA specimens under simple loading conditions – Tension and torsion experimental tests
PublicationThis paper presents the results of experimental testing of flat PMMA specimens during uniaxial loading conditions. Two separate tests were conducted: tensile and torsion. The specimens were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. The specimens were made in two thickness variants: 5 and 15 mm. Monotonic tensile and torsion tests were carried out while keeping the averaged strain rate constant,...
-
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
PublicationVarious types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing...
-
Design criterion for hydrodynamic vortex separators
PublicationTechnical objects designing involves determination of geometrical parameters that characterize a given object. When the device is described by the differential equations, an inverse problem brings difficulties, as geometrical values sought condition the solution to the problem. Vortex separators can be designed by the "criterion method'. Firstly, a critical particle is distinguished such that bigger particles are removed from...
-
Count Data Modeling About Relationship Between Dubai Housing Sales Transactions and Financial Indicators
PublicationIn this study, illustrating and comparing the performances of count data models such as Poisson, negative binomial (NB), Hurdle and zero-inflated models for the determination of factors affected housing sales in Dubai. Model comparisons are made via Akaike’s information criterion (AIC), the Vuong test and examining the residuals. Main purpose of this study is building reliable statistical model for relationship between Dubai housing...
-
L’indistricabile intreccio. Imprese, imprenditori e regime fascista. (An Inextricable Intertwining. Companies, Entrepreneurs, and the Fascist Regime)
PublicationThe papers of this section analyse the relationships between the economic and business community and the fascist regime. Their aim is to refresh the interpretations that were established in the 1960s-1970s and remained undisputed in the decades thereafter, becoming a sort of mantra among Italian contemporary historians. The article presents the most relevant contributions of that historiographical season, explaining the reasons...
-
Selected properties and parameters of radio channel impulse response estimation in ISM 2.4 GHz band
PublicationThe article presents experimental research indicating that the impulse response of the communication channel, determined in practice, are not of an universal character, but only represent its approximate value for the frequency on which this measurement was made. Phases for each of the replicas of the measurement signal were determined during the analysis of the received signals in the baseband. Phase changes of individual replicas...
-
Sparse vector autoregressive modeling of audio signals and its application to the elimination of impulsive disturbances
PublicationArchive audio files are often corrupted by impulsive disturbances, such as clicks, pops and record scratches. This paper presents a new method for elimination of impulsive disturbances from stereo audio signals. The proposed approach is based on a sparse vector autoregressive signal model, made up of two components: one taking care of short-term signal correlations, and the other one taking care of long-term correlations. The method...
-
Influence of nanoparticle concentration on thermal properties of thermal oil-MWCNT nanofluid
PublicationResults of the measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid have been presented. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems as an intermediate heating agent. Multi-walled carbon nanotubes were used...
-
Modal properties identification of a novel sandwich footbridge – Comparison of measured dynamic response and FEA
PublicationA modern sandwich composite footbridge made of high-tech materials, being an example of practical application of laminated composites in civil engineering, is presented. The in situ non-destructive testing of the footbridge, aiming to identify modal properties and pedestrian comfort, is described. The measured eigenmodes and eigenfrequencies are compared with numerically estimated values. Finite element analyses of the footbridge...
-
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublicationThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
Economic benefits of dynamic charging of electric buses
PublicationDiesel engines buses are still the most used type of buses. Electric buses provide promising green alternatives and a lot of advantages, but their main disadvantages are limited travel range and long charging time. This article is a presentation of innovative solution for charging of electric busses - Dynamic Charging (IMC). The modern IMC system in Solingen was presented. At the end of the article, a proposal was made to introduce...
-
The use of machine learning for face regions detection in thermograms
PublicationThe aim of this study is to analyse the methods of detecting characteristic points of the face in thermographic images. As part of the implementation an extensive analysis of scientific publications covering similar issues both for the analysis of images made in visible light and thermographic images was carried out. On the basis of this analysis, 3 models were selected and then they were implemented and tested on the basis of...
-
Preparation of nano-tubular oxide layers on titanium alloy Ti13Nb13Zr
PublicationThe article presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr preformed at different conditions. The oxide layers have been formed using electrochemical method in 2M H3PO4 + 0,3% HF solution for 30 min. and 1h at 20V constant voltage. The corrosion tests heve been made with poteniodynamic method in Ringer's solution at pH ranged 3 and 7. It has been shown that the nano-oxide films, which...
-
Investigation on water infiltration and water content changes in a large-scale experimental test dike
PublicationThe paper presents result of series of experiments made within the DREDGDIKES project, performed on a test dike built from composite soil. The composite is produced by mixing fly ash (by-product of energetics) with dredged material (sand) taken from the mouth of The Vistula river. The test dike, located near Gdansk in Poland, was subjected to hydraulic load in several flooding time scenarios and the unsaturated unsteady flow was...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublicationNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Application of virtual gate for counting people participating in large public events
PublicationThe concept and practical application of the developed algorithm forpeople counting in crowded scene is presented. The aim of the work is to estimatethe number of people passing towards entrances of a large sport hall. Thedetails of implemented the Virtual Gate algorithm are presented. The video signalfrom the camera installed in the building constituted the input for the algorithm.The most challenging problem was the unpredicted...
-
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublicationThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
Dynamic state assessment of the water turbine with the power of 600 kW
PublicationThe article discusses the results of experimental studies to assess the dynamic state of the turbine set with the Kaplan turbine. The dynamic assessment was made on the basis of appropriate standards, based on the measurement results of selected parameters of vibration, which have been measured for several states of the machine load. In addition, we attempted to identify the causes of the increased vibration levels based on the...
-
Performance analysis of power swing blocking feature in ABB 670 series impedance relays
PublicationThis paper presents test results of a distance protection’s PSD power swing detection feature in ABB 670 series relays. A RED670 relay was tested, which is part of the hydroelectric set protection in Żarnowiec Pumped Storage Plant. The power swing blocking feature’s performance was analysed on the basis of the results of object tests made with an Omicron digital tester. Also presented are simulation results that illustrate the...
-
Cough influence on fascia-mesh system built for a hernia repair - an experimental research
PublicationAn experimental approach to identify stronger and weaker fixation schemes in laparoscopic ventral hernia repair is presented in the paper. Two types of implants, whose mechanical properties are significantly different and five kinds of connectors are considered. Physical models of operated hernia have been built using those materials and porcine abdominal tissue. The models have been subjected to dynamic impulse load, similar to...
-
Electrical properties of hybrid planar diode based on palladium phthalocyanine and titanium dioxide
PublicationThis work details experimental studies of a planar diode made of indium tin oxide/titanium dioxide/palladium phthalocyanine/gold. The rectification ratio of current was 105 at 1.5 V. The analysis of the electrical properties of the system was based on small signal complex capacitance spectra measured in the frequency range of 25 Hz-1 MHz at different values of bias. No depletion region at the TiO2/PdPc interface was observed. Forward...
-
A method for counting people attending large public events
PublicationThe algorithm for people counting in crowded scenes, based on the idea of virtual gate which uses optical flow method is presented. The concept and practical application of the developed algorithm under real conditions is depicted. The aim of the work is to estimate the number of people passing through entrances of a large sport hall. The most challenging problem was the unpredicted behavior of people while entering the building....
-
An Analysis of the Relationship between the Architecture and the Structure of a Vessel on the Example of the Reconstruction Design Process of the Historical Sailing Yacht "General Zaruski" Carried Out between 2009 and 2012
PublicationThe article analyzes the relation between architecture and structure of a vessel on the example of the reconstruction design of a wooden sailing yacht "General Zaruski" built in Ekanӓs, Sweden in 1939. Based on the documentation of "Kaparen" (sister yacht), "Mloda Gwardia" (ex "General Zaruski") and the reconstruction classification project made by the authors, the impact of functional, spatial and aesthetic design objectives (e.g....
-
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublicationA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Approach to evaluation of time to the critical degradation of ship pipelines
PublicationIn the article an approach to the problem of estimating time to the critical degradation of ship pipelines is considered. Such an assessment would consist of six stages. The fundamental idea is to include to the estimation of time to failure of pipelines such elements like: materials that the pipelines are made, destructive physical phenomena taking place in them and applied means of protection. The result of that evaluation should...