displaying 1000 best results Help
Search results for: forced vibrations
-
Magnetic properties of of lead-silicate glasses and nanocomposites doped with iron oxide
Open Research DataMagnetic properties of iron-doped glasses and glass-ceramics were studied. Two different sets of glass samples were prepared. The first group of samples has the composition of (50 − 0.5x)SiO2–(50 − 0.5x)PbO– xFe2O3, where x = 15 and 20 (in mol%). Composition of the second group was 50SiO2–(50−x)PbO–xFe2O3, where x=15, 20 and 25 (in mol%). All sampleswere...
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublicationDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
On the Nonlinear Effects of Magnetoacoustic Perturbations in a Perfectly Conducting Viscous and Thermoconducting Gas
PublicationNonlinear effects of planar and quasi-planar magnetosound perturbations are discussed. The plasma is as- sumed to be a Newtonian thermoconducting gas with infinite electrical conductivity permeated by a magnetic field orthogonal to the trajectories of gas particles. Generation of the non-wave modes (magnetoacoustic heating and streaming) in the field of periodic and aperiodic magnetoacoustic perturbations is discussed. The results...
-
The Process of Building Civil Society against the Shortcomings of Polish Planning Legislation
PublicationThe article presents the main assumptions of the project of Coastal Strip development in Gdansk. According to the authors best knowledge this is the first pro publico bono project in Poland in a large area of the city formed on the initiative of and elaborated by the city's inhabitants supported by two NGOs. Successive stages of the project preparation are discussed on the background of the shortcomings of Polish planning law...
-
Idea zastosowania sztucznej inteligencji w prognozowaniu wpływu drgań komunikacyjnych na odpowiedź dynamiczną budynków mieszkalnych
PublicationW poniższym artykule autorzy analizują wpływ drgań komunikacyjnych na budynki mieszkalne oraz metodykę pomiarową według PN-85 B-02170 [1]. Problemem badawczym jest opracowanie prostej metody prognozowania wpływu drgań na budynki mieszkalne w taki sposób, aby nie było konieczne przeprowadzanie pracochłonnych i kosztownych pomiarów polowych. W tym celu wykonano analizę przy użyciu algorytmów opartych na sztucznej inteligencji oraz...
-
Technical diagnostics and monitoring of traction current collectors
PublicationNew evaluation methods of the technical condition of rolling stock current collectors are proposed in this paper. The method of automatic measurement of the pantograph static force characteristic, realized when the vehicle runs through the test section of the track with especially prepared overhead line height distribution, has been practically implemented by the Polish Railways. The method of testing the slipper spring suspension...
-
Influence of geometrical and operational parameters on tooth wear in the working mechanism of a satellite motor
PublicationThis article describes the phenomena affecting the wear of the rotor of the working mechanism in a hydraulic satellite motor. The basic geometrical relationships that allow the calculation of the coordinates of the points of contact between the satellite and the rotor and the curvature are presented. A method for calculating the number of contacts of the satellite teeth with the rotor teeth and of the satellite teeth with the curvature...
-
2022-2023 - Strenght of materials towards applications, PG_00053661
e-Learning CoursesThe course is mainly dedicated to the DAPE Students. From the theoretical point of view the course consists of the following problems to be discussed during the lectures and exercises: -fundamentals of strength of materials -basic structures and environment -loads on structures -strength of materials: tension, stress, analysis of stress and strain, bending moments and shearing forces, longitudinal and shearing stress in beams,...
-
Strenght of materials towards applications , PG_00053661
e-Learning CoursesThe course is dedicated to the DAPE WIMiO Students. From the theoretical point of view the course consists of the following problems to be discussed during the lectures: -fundamentals of strength of materials -basic structures and environment -loads on structures -strength of materials: tension, stress, analysis of stress and strain, bending moments and shearing forces, longitudinal and shearing stress in beams, bending stress...
-
Intelligent Material Actuators and Their Applications for Structural Dynamic Control
PublicationThe paper presents an application of inteligent materials to vibration control of structures.
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublicationsettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
Pile Model Tests Using Strain Gauge Technology
PublicationOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
Market Price Prediction of Property Rights from Gas Fired Plants or Plants with Total Installed CHP Source Capacity Below 1 MW until 2025
PublicationThe resolution on the Polish Energy Policy until 2030 (PEP-30) was adopted by the Council of Ministers on 10 November 2009. The document specifies the combined electricity and heat generation as a direction of pursuing the goals of energy efficiency, fuel and energy supply security, competitive fuel and energy markets development, and reduction of the energy sector’s environmental impact. PEP-30 assumes that electricity generation...
-
Analiza drgań kładki kompozytowej wywołanych działaniem wiatru
PublicationW pracy omówiono sposób przeprowadzenia uproszczonej, numerycznej analizy drgań kładki kompozytowej wywołanych działaniem wiatru. Rozważaniom poddano swobodnie podpartą konstrukcję o rozpiętości 16 m i przekroju w kształcie litery U. W pierwszej kolejności przeprowadzono dwuwymiarową analizę opływu niepodatnego kształtu przekroju kładki w poziomym strumieniu wiatru o prędkości 10 m/s. Obliczenia numeryczne przeprowadzono programem...
-
A newly-developed model for predicting cutting power during wood sawing with circular saw blades
PublicationIn the classical approach, cutting forces and cutting power in sawing processes of orthotropic materials such as wood are generally calculated on the basis of the specific cutting resistance kc (cutting force per unit area of cut). For every type of sawing kinematics (frame saws, band saws and circular sawing machines) different empirical values of specific cutting resistance kc have to be applied. It should be emphasised that...
-
Optimized Stress and Geometry Control of Spherical structures under Lateral Loadings
PublicationIn this paper, a numerical model of a double-layer spherical structure has been examined under lateral loadings. When the structure has been distorted due to loadings, the dislocated joints have been moved to their original positions utilizing the adjustment techniques based on the force method. Meanwhile, the members’ internal forces were kept in the desired domain. Optimization techniques were also implemented in order to minimalize...
-
Average number of hours worked per week by women aged 15 and older (Poland, Lithuania, Latvia, Estonia)
Open Research DataThe following dataset presents the average weekly number of hours worked by women in selected countries (Poland, Lithuania, Latvia, Estonia) in the years 1999 - 2016. The summary includes average weekly time worked in the main job, for women aged 15+. The estimates correspond to the declared amount. This includes part-time and full-time employment,...
-
Inventory of the eastern wall of the presbytery of the former Dominican church - St. Mary's Church in Elbląg, stage from 2015.
Open Research DataThe drawing presents an inventory of the eastern wall of the presbytery of the former Dominican church - St. Mary's Church in Elbląg (now Art Gallery: Galeria EL), stage from 2015.The drawing also indicates the original, not overfolded during subsequent conservation and construction works, fragments of walls from 3 medieval stages of construction.
-
Prognozowanie wpływu drgań komunikacyjnych na budynki mieszkalne za pomocą sztucznych sieci neuronowych i maszyn wektorów wspierających
PublicationDrgania komunikacyjne mogą stanowić duże obciążenie eksploatacyjne budynku, powodując zarysowania i spękania tynków, odpadanie wypraw, zarysowania konstrukcji, pękanie elementów konstrukcji lub nawet zawalenie się budynku. Pomiary drgań na rzeczywistych konstrukcjach są pracochłonne i kosztowne, a co ważne nie w każdym przypadku są one uzasadnione. Celem pracy jest analiza autorskiego algorytmu, dzięki któremu z dużym prawdopodobieństwem...
-
STRENGTH of MATERIALS TOWARDS APPLICATIONS (2024)
e-Learning CoursesThe SMTA DATE Course consists of the following problems to be discussed during the lectures: - Introduction to strength of materials towards applications - Fundamentals of modelling in strength of materials towards applications - Materials and basic structures - Fundamentals of modelling in strength of materials towards applications - Definition of environment and loads - General, energy-based and advanced methods for analysis...
-
On some problems in determining tensile parameters of concrete model from size effect tests
PublicationThe paper presents results of numerical simulations of size effect phenomenon in concrete specimens. The behaviour of in-plane geometrically similar notched and unnotched beams under three-point bending is investigated. In total 18 beams are analysed. Concrete beams of four different sizes and five different notch to depth ratios are simulated. Two methods are applied to describe cracks. First, an elasto-plastic constitutive law...
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublicationThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
Numerical investigation on dynamic performance of a multi-storey steel structure model and comparison with experimental results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Dynamic analysis of temporary steel grandstand equipped with different types of bracing system
PublicationIn the paper, behaviour of a temporary steel grandstand equipped with two different types of bracing system has been analysed through the numerical study. A typical solution concerning application of a diagonal tubular members has been compared with elements proposed by authors and called polymer dampers. A polymer element consists of two L-shape steel members bonded with polymer mass. The aim of the paper is to verify the effectiveness...
-
Luminescence properties of Eu3+ and Tb3+ doped silica-based xerogels
PublicationPure SiO2 xerogels and SiO2 xerogels containing SrF2: Eu3+/: Tb3+ crystals were prepared using sol-gel method. Luminescent spectra showed excitation and emission peaks characteristic to Eu3+ and Tb3+ 4f - 4f transitions. ET Tb3+→Eu3+ has been observed. XRD pattern of SiO2 matrix confirmed lack of long range order. Patterns of SiO2-SrF2:Eu3+ and SiO2-SrF2:Tb3+ showed peaks corresponding to SrF2. SEM images have shown agglomerates...
-
Wykorzystanie sztucznych sieci neuronowych do szacowania wpływu drgań na budynki jednorodzinne
PublicationW artykule przedstawiono metodę prognozowania wpływu drgań na budynki mieszkalne z wykorzystaniem sztucznych sieci neuronowych. Drgania komunikacyjne mogą doprowadzić do uszkodzenia elementów konstrukcyjnych, a nawet do awarii budynku. Najczęstszym efektem są jednak rysy, pękanie tynku i wypraw. Metody oparte na sztucznej inteligencji są przybliżone, ale stanowią wystarczająco dokładną i ekonomiczną alternatywę dla tradycyjnych...
-
Dynamic analysis of the railway bridge span under moving loads
PublicationThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
The effect of circular saw blade clamping diameter on its resonant frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with the...
-
Hyperelastic Microcantilever AFM: Efficient Detection Mechanism Based on Principal Parametric Resonance
PublicationThe impetus of writing this paper is to propose an efficient detection mechanism to scan the surface profile of a micro-sample using cantilever-based atomic force microscopy (AFM), operating in non-contact mode. In order to implement this scheme, the principal parametric resonance characteristics of the resonator are employed, benefiting from the bifurcation-based sensing mechanism. It is assumed that the microcantilever is made...
-
Numerical modeling of quantum dynamical processes
PublicationIn this dissertation I present a high-precision (15, 18 or 33 decimal places) C++ implementation of quantum dynamics time propagation algorithms for both time-independent and time-dependent Hamiltonian with an inhomogeneous source term. Moreover I present an extension of both algorithms for time propagation to handle arbitrary number of coupled electronic levels. I have performed a careful validation of these implementations comparing...
-
Numerical analysis of lumbar spine injury during road safety barrier collision
PublicationPurpose: Enhancing road safety is a critical goal worldwide, necessitating the development of clear standards for road safety systems. This study focuses on lumbar spine (L-spine) compression injuries during collisions with concrete road safety barriers (RSBs). It aims to analyze internal forces during impact to understand L-spine injury biomechanics in such accidents. Methods: The research included a literature review, analyzing...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublicationThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
Molecular hydrogen solvated in water – A computational study
PublicationThe aqueous hydrogen molecule is studied with molecular dynamics simulations at ambient temperature and pressure conditions, using a newly developed flexible and polarizable H2 molecule model. The design and implementation of this model, compatible with an existing flexible and polarizable force field for water, is presented in detail. The structure of the hydration layer suggests that first-shell water molecules accommodate the...
-
Laboratorium Drgań i Zjawisk Falowych/Laboratory of vibrations and wave phenomena
e-Learning Courses -
Laboratorium drgań i zjawisk falowych / Laboratory of vibrations and wave phenomena
e-Learning CoursesSpecjalność: Fizyka stosowana (WFTiMS),I stopnia - inżynierskie, stacjonarne, 2020/2021 - zimowy (obecnie sem. 3)Specjalność: Inżynieria odnawialnych źródeł energii (WFTiMS),I stopnia - inżynierskie, stacjonarne, 2020/2021 - zimowy (obecnie sem. 3)
-
Development and Verification of the Diagnostic Model of the Sieving Screen
Publication -
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublicationThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
An approach for the response of buildings subjected to impact load after soft-story failure due to earthquake excitation
Publicationhe soft-story failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an intermediate soft story of a structure results in large impact loading acting on the lower floors due to the fall of the upper stories. The aim of the present paper is to study the behavior of the structural members exposed to such extreme load conditions occurring under ground motion excitation. Special...
-
Updating Finite Element Model of a Wind Turbine Blade Section Using Experimental Modal Analysis Results
PublicationThis paper presents selected results and aspects of themultidisciplinary and interdisciplinary research oriented for the experimental and numerical study of the structural dynamics of a bend-twist coupled full scale section of awind turbine blade structure.Themain goal of the conducted research is to validate finite elementmodel of themodified wind turbine blade section mounted in the flexible support structure accordingly to the...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
A Bayesian regularization-backpropagation neural network model for peeling computations
PublicationA Bayesian regularization-backpropagation neural network (BRBPNN) model is employed to predict some aspects of the gecko spatula peeling, viz. the variation of the maximum normal and tangential pull-off forces and the resultant force angle at detachment with the peeling angle. K-fold cross validation is used to improve the effectiveness of the model. The input data is taken from finite element (FE) peeling results. The neural network...
-
The spontaneous electron emission and rotational predissociation lifetimes of the diatomic silver anion
Open Research DataThe process of a two-channel decay of the diatomic silver anion (Ag2-), namely the spontaneous electron ejection giving Ag2 + e- and the dissociation leading to Ag- + Ag is theoretically studied. The ground state potential energy curves (PECs) of the neutral silver dimer and anionic silver diatomic molecule are calculated using the single reference...
-
Dynamics Conscious Approach to Tribometer Design and Tribo-testing
PublicationIn the paper findings are discussed on the issue of dynamic characteristics of a tribometer as a factor influencing the result of the tribological experiment. An advanced approach to tribo-testing is attempted with integrated dynamic analysis of the tribometer and the sliding pair. The fundamental idea is explored of the tribometer being regarded as any machine in which friction is inflicted with all the resulting consequences...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Assessment of Subsoil Subsidence Under the Railway Surface with the Use of Fuzzy Sets
PublicationThe cause of the subsidence of the railway track is the subsidence of the track bed itself and it is often related to the subsidence of the subsoil. Such settlement leads to: uneven longitudinal railways and track twist. These phenomena have a negative impact on the comfort and safety of driving, and in extreme cases lead to a train derailment. It has been shown that the magnitude of these settlements is determined by many parameters...
-
Zbigniew Czaja dr hab. inż.
PeopleZbigniew Czaja was born in Czluchow, Poland, in 1970. He graduated from Gdansk University of Technology, Faculty of Electronics, Telecommunications and Informatics in 1995. The Ph.D. degree in electronics was received in 2001 from the same university. He worked as assistant professor at this university from 2002 to 2013. In 2014, he qualified as an associate professor, and in 2017, as a professor. His research interests are in...
-
Estimation of nonstructural stiffness in instrumented steel frames
PublicationLateral stiffness of nonstructural components may significantly influence the initial stiffness of the entire structure and consequently alter its dynamic characteristics. While methods for simulating structural members are well-established, approaches for modeling nonstructural components that also participate in seismic response are notably less developed. In this paper a simplified, physically-intuitive approach for estimating...
-
LSP Journal - Language for special purposes, professional communication, knowledge management and cognition (former title: LSP and Professional Communication)
Journals -
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublicationThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
Underwater acoustic communication system using broadband signal with hyperbolically modulated frequency
PublicationThe implementation of reliable acoustic underwater communication in shallow waters is a scientific and engineering challenge, mainly due to the permanent occurrence of the multipath phenomenon. The article presents the concept of a transmission system using a broadband signal with hyperbolically modulated frequency (HFM) to transmit data symbols and synchronize data frames. The simulation tests were carried out in channels with...