Search
Filters
total: 785
filtered: 702
Search results for: CIRCUIT THEORY, CIRCUIT SIMULATION, TRANSMISSION LINES, FRACTIONAL CALCULUS
-
Design of Intelligent Low-Voltage Load Switch for Remote Control System in Smart Grid
PublicationCurrent low-voltage load switches do not support remote disconnect/connect and real-time monitoring of a disconnect/connect state. Addressing to these issues, this paper presents a low-voltage load switch for a smart remote control system, which uses a one-chip microcontroller board and a DC step motor drive mechanism and provides the feedback on the switch status also. Arrears disconnect and full-pay connect control is implemented...
-
Wizyjny system monitoringu stanu nakładek stykowych odbieraków prądu
PublicationEksploatowane do niedawna w Polsce nakładki pantografów kolejowych były wykonywane w postaci styków miedzianych. Na początku 2011 r. przeprowadzono kompleksową zmianę typu nakładek stykowych, stosowanych przez operatorów korzystających z infrastruktury PKP PLK S.A., z miedzianych na metalizowane węglowe. Wraz z wprowadzeniem nakładek węglowych istnieje potrzeba opracowania nowych metod diagnostyki tego istotnego elementu toru zasilania...
-
Analiza przepływu gazu w kanałowych reduktorach ciśnienia podczas zwarć łukowych w rozdzielnicach SN
PublicationW artykule przedstawiono metodę obliczania ciśnienia i temperatury gazów podczas zwarcia łukowego wewnątrz przedziału wyłącznika rozdzielnicy średniego napięcia z wykorzystaniem modelu termodynamicznego procesów towarzyszących zwarciom łukowym wewnątrz rozdzielnic z izolacją powietrzną. Następnie, w oparciu o mechanikę płynów lepkich, przedstawiono metodę obliczania rozkładu prędkości i ciśnienia gazu w kanałowych reduktorach ciśnienia...
-
Analiza i badania systemu antyspoofingowego GPS
PublicationArtykuł dotyczy problemu spoofingu w systemie GPS, polegającego na niepowołanej transmisji sygnałów imitujących sygnały odbierane z satelitów GPS. Takie działanie prowadzi do wyznaczenia przez odbiornik nawigacyjny nieprawidłowego położenia, prędkości i czasu. Zostały opisane metody przeciwdziałania spoofingowi, w szczególności poprzez przestrzenne przetwarzanie sygnałów. Przedstawiono wyniki badań symulacyjnych efektywności tych...
-
Szybka identyfikacja harmonicznych na podstawie oszczędnego próbkowania
PublicationW pracy przedstawiono implementację szybkiego algorytmu rekonstrukcji sygnału, opartego na teorii oszczędnego próbkowania, który może wykrywać harmoniczne w sygnale wejściowym. Zagadnienie rekonstrukcji sygnału jest problemem optymalizacyjnym rozwiązywanym za pomocą algorytmu programowania liniowego. Dodatkowo, aby przyspieszyć zbieżność rozwiązania zastosowano w rzadkiej dziedzinie sygnału filtr typu K-rank-order. Przeprowadzona...
-
Study of the Flow Dynamics of Surface Water Masses in the Area of the Coastal Gulf of Gdansk
PublicationThe paper describes two methods of predicting the movement of small objects with surface water masses. One of the methods uses graph theory to describe the motion of water masses in port docks. The results of this study were compared to a simulation using the hydrodynamic numerical model M3D. The results obtained in a virtual environment were related to the experiments in the real world. In the coastal area of the Gulf of Gdansk,...
-
Modelling of Longitudinal Elastic Wave Propagation in a Steel Rod Using the Discrete Element Method
PublicationThe paper deals with the issue of modelling elastic wave propagation using the discrete element method (DEM). The case of a longitudinal wave in a rod with a circular cross-section was considered. A novel, complex algorithm consisting of the preparation of models and simulation of elastic waves was developed. A series of DEM models were prepared for simulations, differing in discretisation and material parameters. Additional calculations...
-
Using water sources extent during inundation as a reliable predictor for vegetation zonation in a natural wetland floodplain
PublicationDistinctive zones of inundation water during floods were shown to originate from different sources in some major floodplains around the world. Recent research showed that the zonation of water in rivers and floodplains is related to vegetation patterns. In spite of this, water source zones were not used for vegetation modeling due to difficulties in their delineation. In this study, we used simulation results of a fully-coupled...
-
Evolution of Ag nanostructures created from thin films: UV–vis absorption and its theoretical predictions
PublicationAg-based plasmonic nanostructures were manufactured by thermal annealing of thin metallic films. Structure and morphology were studied using scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS). SEM images show that the formation of nanostructures is influenced by the initial layer thickness as well as the...
-
Conception and design of a hybrid exciter for brushless synchronous generator. Application for autonomous electrical power systems = Koncepcja i projekt hybrydowej wzbudnicy bezszczotkowego generatora synchronicznego. Zastosowanie w autonomicznych systemach elektroenergetycznych
PublicationIn this paper a hybrid excitation system for a brushless synchronous generator working with variable speed in an autonomous energy generation system (e.g. airplane power grid) has been presented. A conception of a dual-stator hybrid exciter has been proposed. Comparison study of classical and hybrid exciter has been carried out. For the electromagnetic calculation two approaches have been applied: an analytical approach (based...
-
Induction motor control application in high-speed train electric drive
PublicationThe chapter presents an application of induction motor mechanical speed and load torque observers in high-speed train drives. The observers are applied for a 1.2-MW electric drive with an induction motor. The goal of using such observers is to utilize computed variables for diagnostic purposes of speed sensors and torque transmission system. The concept of diagnostic system is presented in this paper, and proper criteria are proposed....
-
A Novel Bitrate Adaptation Method for Heterogeneous Wireless Body Area Networks
PublicationIn the article, a novel bitrate adaptation method for data streams allocation in heterogeneous Wireless Body Area Networks (WBANs) is presented. The efficiency of the proposed algorithm was compared with other known algorithms of data stream allocation using computer simulation. A dedicated simulator has been developed using results of measurements in the real environment. The usage of the proposed adaptive data streams allocation...
-
A Novel Bitrate Adaptation Method for Heterogeneous Wireless Body Area Networks
PublicationIn the article, a novel bitrate adaptation method for data streams allocation in heterogeneous Wireless Body Area Networks (WBANs) is presented. The efficiency of the proposed algorithm was compared with other known algorithms of data stream allocation using computer simulation. A dedicated simulator has been developed using results of measurements in the real environment. The usage of the proposed adaptive data streams allocation...
-
Balancing energy consumption in limited power grid with active front-end and three phase dual active bridge system
PublicationPaper deals with simulation analysis of bidirectional power converters system for charging station of electric vehicle in condition of limited power source in city infrastructure. In case of incapability to provide additional power supply through the grid by virtue of historical, architectural and economic reasons it is possible to solve this issue by implementation of mobile battery-powered supply source. The proposed bidirectional...
-
Multiple access in ad-hoc wireless LANs with noncooperative stations
PublicationA class of contention-type MAC protocols (e.g., CSMA/CA) relies on random deferment of packet transmission, and subsumes a deferment selection strategy and a scheduling policy that determines the winner of each contention cycle. This paper examines contention-type protocols in a noncooperative an ad-hoc wireless LAN setting, where a number of stations self-optimise their strategies to obtain a more-than-fair bandwidth share. Two...
-
Optimization-Based Robustness Enhancement of Compact Microwave Component Designs with Response Feature Regression Surrogates
PublicationThe ability to evaluate the effects of fabrication tolerances and other types of uncertainties is a critical part of microwave design process. Improving the immunity of the device to parameter deviations is equally important, especially when the performance specifications are stringent and can barely be met even assuming a perfect manufacturing process. In the case of modern miniaturized microwave components of complex topologies,...
-
Inverse modeling for fast design optimization of small-size rat-race couplers incorporating compact cells
PublicationIn the paper, a framework for computationally-efficient design optimization of compact rat-race couplers (RRCs) is discussed. A class of hybrid RRCs with variable operating conditions is investigated, whose size reduction is obtained by replacing ordinary transmission lines with compact microstrip resonant cells (CMRCs). Our approach employs a bottom-up design strategy leading to the development of compact RRCs through rapid design...
-
FEM simulation of laminate failure in the three point bending
PublicationThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Observation on red blood cells fluctuations by diffraction phase microscopy
PublicationNowadays there is quite huge need for more and more precise and effective fast diagnostics methods in hematology diseases. One of the most important blood components are erythrocytes – Red Blood Cells (RBCs). Due to their size they are easy to observe using microscopy. It is commonly known that the shape and lifetime of RBCs allows for early disease identification. Authors present special measurement system for RBCs fluctuations...
-
Multiple output CMOS current amplifier
PublicationIn this paper the multiple output current amplifier basic cell is proposed. The triple output current mirror and current follower circuit are described in detail. The cell consists of a split nMOS differential pair and accompanying biasing current sources. It is suitable for low voltage operation and exhibits highly linear DC response. Through cell devices scaling, not only unity, but also any current gains are achievable. As...
-
Piezoresponse force microscopy and dielectric spectroscopy study of Ba0.6Sr0.4TiO3 thin films
PublicationResearch on synthesis, characterization and determination of processing – structure – property relationships of commercially important ferroelectric thin films has been performed. The sol-gel-type solution deposition technique was applied to produce good quality thin films of Ba0.6Sr0.4TiO3 (BST60/40) chemical composition on the stainless steel substrates. The thin films were characterized in terms of their microstructure, crystal...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublicationWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Distribution of relaxation times as a method of separation and identification of complex processes measured by impedance spectroscopy
PublicationImpedance spectroscopy is one of the most commonly performed measurements to characterize electronic and electrochemical systems. Impedance spectra have limited resolution and many different processes may overlap what could be the reason of obstructions in its proper later analysis. Up to date, there are three approaches to solve this problem: examining impedance spectra itself, fitting spectra with equivalent circuits, and calculating...
-
Induced-fit binding of laccase to gold and carbon electrodes for the biological fuel cell applications
PublicationAnalogues of laccase natural substrates (syringic, veratric, ferulic, vanillic, isovanillic, 3,5-dimethoxybenzoic aldehydes) were employed to bind and orient laccase molecules in a way which facilitates adsorption of the catalyst molecules and their electrical connection with the conductive support. Laccase was bound efficiently to these substrates both on gold and carbon electrodes forming, respectively, 2D and 3D films sensitive...
-
Simple Measurement Method for Resistive Sensors Based on ADCs of Microcontrollers
PublicationA new, complete measurement method for resistance measurement of resistive sensors for systems based on microcontrollers equipped with analog-to-digital converters (ADCs) is proposed. The interface circuit consists of only four resistors, including a resistive sensor and a reference resistor, connected directly to the microcontroller pins. It is activated only during measurements, which significantly reduces power consumption....
-
A Simple-Topology Compact Broadband Circularly Polarized Antenna With Unidirectional Radiation Pattern
PublicationIn this letter, a geometrically simple, reflector-backed single-point-fed circularly polarized (CP) antenna with unidirectional radiation pattern is presented. The structure comprises a simple coplanar waveguide (CPW) feeding circuit with an open slot etched on one side of the coplanar ground. The enhanced CP bandwidth is obtained by combining the loop mode, the slot mode, and the asymmetrical configuration of the coplanar ground...
-
Improved RSS-Based DoA Estimation Accuracy in Low-Profile ESPAR Antenna Using SVM Approach
PublicationIn this paper, we have shown how the overall performance of direction-of-arrival (DoA) estimation using lowprofile electronically steerable parasitic array radiator (ESPAR) antenna, which has been proposed for Internet of Things (IoT) applications, can significantly be improved when support vector machine (SVM) approach is applied. Because the SVM-based DoA estimation method used herein relies solely on received signal strength...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublicationIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
Fault-tolerant performance of the novel five-phase doubly-fed induction generator
PublicationThe article presents the concept of a new design of a multi-phase doubly-fed induction generator (DFIG). The innovative design approach uses a five-phase power supply from the rotor side of the generator with a three-phase classic stator power supply. Modern three-phase doubly-fed induction generators are the dominant choice for Wind Energy Conversion Systems (WECS). Solutions of this type are sensitive to the loss of at least...
-
Vehicle Detection with Self-Training for Adaptative Video Processing Embedded Platform
PublicationTraffic monitoring from closed-circuit television (CCTV) cameras on embedded systems is the subject of the performed experiments. Solving this problem encounters difficulties related to the hardware limitations, and possible camera placement in various positions which affects the system performance. To satisfy the hardware requirements, vehicle detection is performed using a lightweight Convolutional Neural Network (CNN), named...
-
Product Graph Invariants with Applications in the Theory of Information
PublicationThere are a large number of graph invariants. In the paper, we consider some of them, e.g. the independence and chromatic numbers. It is well know that we cannot efficiently calculate these numbers for arbitrary graphs. In the paper we present relations between these invariants and concepts from the theory of information. Concepts such as source coding and transmission over a noisy channel with zero probability of error are modeled...
-
Bandwidth-Controllable Third-Order Band Pass Filter Using Substrate Integrated Full- and Semi-Circular Cavities
PublicationThe article presents a novel circular substrate integrated waveguide (SIW) bandpass filter (BPF) with controllable bandwidth. The proposed BPF is configured using two microstrip feedlines, semi- circular SIW cavities, capacitive slots, and inductive vias. The circular cavity is bisected into two halves, with the two copies thereof being cascaded. Two bisected and cascaded structures obtained this way are subsequently connected...
-
Demonstrator testera wbudowanego BIST dla układów w pełni różnicowych
PublicationPrzedstawiono demonstrator testera wbudowanego, przeznaczony do pracy na stanowisku dydaktycznym w laboratorium z przedmiotu Zaawansowane Metody Pomiarowe i Diagnostyczne. Na stanowisku studenci zapoznają się z technologią BIST (ang. Built-In Self-Test), która jest przykładem wdrożenia strategii projektowania dla testowania.
-
Identification of ship’s hull mathematical model with numerical methods
PublicationThe modern maritime industry is moving toward the development of technology that will allow for full or partial autonomy of ship operation. This innovation places high demands on ship performance prediction techniques at the design stage. The researchwork presented in the article is related to the design stage of the ship and concerns methods for prognosis and evaluation of the specific operational condition of the ship, namely...
-
Propagation Characteristics of Partial Discharges in an Oil-Filled Power Transformer
PublicationPower transformers are among the most important assets in the power transmission and distribution grid. However, they suffer from degradation and possible faults causing major electrical and financial losses. Partial discharges (PDs) are used to identify the insulation health status and their degradation level. PDs are incipient, low-magnitude faults caused by localized dielectric breakdown. Those activities emit signals in many...
-
A Model of Thermal Energy Storage According to the Convention of Bond Graphs (BG) and State Equations (SE)
PublicationThe main advantage of the use of the Bond Graphs method and State Equations for modeling energy systems with a complex structure (marine power plants, hybrid vehicles, etc.) is the ability to model the system components of different physical nature using identical theoretical basis. The paper presents a method of modeling thermal energy storage, which is in line with basic BG theory. Critical comments have been put forward concerning...
-
Visualization of a lifeboat motion during lowering along ship’s side
PublicationThis paper presents description of a computer program for motion visualization of a lifeboat lowered along ship’s side. The program is a post-processor which reads results of numerical calculations of simulated objects’ motions. The data is used to create scene composed of 3D surfaces to visualize mutual spatial positions of a lifeboat, ship’s side and water waving surface. Since the numerical data contain description of a simulation...
-
A New Direct-Sequence Spread Spectrum Signal Detection Method for Underwater Acoustic Communications in Shallow-Water Channel
PublicationDirect-Sequence Spread Spectrum (DSSS) is one of the modulation and coding techniques used in Underwater Acoustic Communication (UAC) systems for reliable data transmision even at low signal levels. However, in a shallow water channel, there is a strong multipath propagation which causes a phase fluctuation of the received signal, affecting the performance of the spread-spectrum system. The article presents a differential method...
-
A Multifunctional Microwave Filter/Sensor Component Using a Split Ring Resonator Loaded Transmission Line
PublicationThis research is focused on the design and realiza2 tion of a microwave component with multifunctional filter/sensor 3 operation using a resonator-loaded transmission line (TL). It is 4 shown that while the structure acts as a bandstop filter, the 5 phase of the reflection coefficient from the loading resonator(s) 6 on a movable layer can be used for displacement sensing, thus 7 allowing for combining filtering with sensing in...
-
Diagnostics of induction motor bearings - possibility of measurements
PublicationIn induction motors damage in the elements of electromagnetic system, for example in the wiring of stator, rotor or in the magnetic circuit can appear as well as damage of mechanical parts (bearings, rotor, shaft). Bearing diagnostics is so important in supervision of motor condition, because extensive research shows that the bearings arethe elements most susceptible to damage. This paper presents the research which the author...
-
In-situ and ex-situ resistance measurements of polypyrrole film using double-band electrode
PublicationMany in-situ techniques are performed in order to determine the resistance of conducting polymer film. However, the resistance measured in solution can be the combination of polymer resistance and that of other components, such as resistance of supporting electrolyte. Therefore, in this work, the influence of the solution on the resistance of polypyrrole (PPy) film has been studied. PPy film was electrchemically synthesized onto...
-
Portable exhaled breath analyzer employing fluctuation-enhanced gas sensing method in resistive gas sensors
PublicationThis paper presents a portable exhaled breath analyser, developed to detect selected diseases. The set-up employs resistive gas sensors: commercial MEMS sensors and prototype gas sensors made of WO3 gas sensing layers doped with various metal ingredients. The set-up can modulate the gas sensors by applying UV light to induce physical changes of the gas sensing layers. The sensors are placed in a tiny gas chamber of a volume...
-
Electric shock hazard in circuits with variable-speed drives
PublicationThe conventional approach to electrical safety under fault condition in typical power systems considers earth fault currents of sinusoidal waveform and frequency of 50/60 Hz. However, in circuits with variable-speed drives, there is earth fault current flow with harmonics, and these harmonics influence the threshold of ventricular fibrillation. The paper presents earth fault current waveforms in circuits with variable-speed drives...
-
Low-cost and reliable geometry scaling of compact microstrip couplers with respect to operating frequency, power split ratio, and dielectric substrate parameters
PublicationA technique for rapid re-design of miniaturised microstrip couplers with respect to operating conditions as well as material parameters of the dielectric substrate is proposed. The dimension scaling process is based on a set of pre-optimised reference designs, obtained for an equivalent circuit model of the coupler at hand. The reference designs are utilised to construct an inverse surrogate model which – upon suitable correction...
-
Asynchronous Charge Carrier Injection in Perovskite Light-Emitting Transistors
PublicationUnbalanced mobility and injection of charge carriers in metal-halide perovskite light-emitting devices pose severe limitations to the efficiency and response time of the electroluminescence. Modulation of gate bias in methylammonium lead iodide light-emitting transistors has proven effective in increasing the brightness of light emission up to MHz frequencies. In this work, a new approach is developed to improve charge carrier...
-
COMPARISON OF SYSTEM ON CHIP TECHNOLOGIES FOR SPACE APPLICATIONS
PublicationThe paper presents a review of technologies available for the implementation of digital and mixed signal systems, particularly the system on a chip (SoC) for space applications. The phenomena encountered in the space environment are briefly presented, together with the known solutions, regarding the design of complex electronic systems. The most important norms regarding single die integrated circuits designed for space are also...
-
Innovative Bidirectional Isolated High-Power Density On-Board Charge for Vehicle-to-Grid
PublicationThis paper deals with developing and implementing a bidirectional galvanically isolated on-board charger of a high-power density. The power density of the new charger was 4 kW/kg and 2.46 kW/dm3, and the maximum efficiency was 96.4% at 3.4 kW. Due to the requirement to achieve a high-power density, a single-stage inverter topology was used. Regarding switching losses, due to the topology of the circuit with so-called hard switching,...
-
Design of an Autonomous IoT Node Powered by a Perovskite-Based Wave Energy Converter
PublicationThis paper presents the results of experimental research focused on wave energy harvesting and its conversion to power Internet of Things (IoT) devices. The harvesting and conversion process was performed using a wave energy converter (WEC) consisting of a lead zirconate titanate piezoelectric ceramic perovskite material and a prototype power electronic circuit. The designed WEC was considered as a power supply for an end node...
-
Highly stable CsFAPbIBr perovskite solar cells with dominant bulk recombination at real operating temperatures
PublicationMixed-cation mixed-halide perovskite solar cells have been characterized in DC at different temperatures (from −20 °C up to 50 °C) and the time evolution of the device efficiency has been assessed using different degradation protocols (indoors and outdoors). The completely planar p–i–n structure is ITO/CuNiOx/PTAA/CsFAPbIBr/PCBM/PEI/Ag. Pristine current–voltage characteristics barely show hysteresis, at any temperature. Open circuit...
-
Study of oxygen electrode reactions on symmetrical porous SrTi0.30Fe0.70O3-δ electrodes on Ce0.8Gd0.2O1.9 electrolyte at 800 °C–500 °C
PublicationIron doped strontium titanates (SrTi1-xFexO3-δ) are an interesting mixed ionic-electronic conductor model used to study basic oxygen reduction/oxidation reactions. In this work, we performed an impedance spectroscopy study on symmetrical porous SrTi0.30Fe0.70O3-δ (STF70) electrodes on a ceriabased electrolyte. The sample was measured in varying oxygen concentration: from 0.3% to 100% in 800 °C - 500 °C temperature range. Low polarisation...