displaying 1000 best results Help
Search results for: LOAD, MEASURING STANDARD
-
Calculation of an ultimate load value of a silo with geometric imperfections in the shape of eigenforms
PublicationThe ultimate load value of a silo with initial geometric imperfections was measured. The structure was loaded with wind. Imperfections were assumed as translations of the shell nodes from perfect geometry taken from eigenforms and their combinations. Two variants of the maximum deflection placement with respect to the direction of wind pressure were proposed. The first consists in applying the maximum wind pressure to the element...
-
An in situ technique for the assessment of adhesive properties of a joint under load
PublicationSlow crack propagation in adhesive bonded joints has been characterised using an asymmetric wedge test. Crack position was evaluated from strain gauge measurements, both in the debonded partof the joint and in the bonded zone. Test temperature was changed during loading, giving insight into bond evolution. The technique allows accurate, and virtually continuous, determination of crack position to be made, and therefore the evaluation...
-
Influence of local bush wear on water lubricated sliding bearing load carrying capacity
PublicationOne of main problems concerning water-lubricated bearings is their durability. There are known cases of bearings with life time measured in decades, and some, whose refurbishment was necessary just days after start-up. Obtaining stable fluid film friction plays key role in the durability of these bearings. Unfortunately, their load-carrying capacity is limited due to water's low-viscosity. The conducted experimental...
-
Performance analysis of standard and modified EY-NPMA channel access algo-rithms
PublicationPodczas minionego 10-ciolecia notuje się szybki rozwój lokalnych sieci bezprzewodowych (WLANy). Proponowane rozwiązania dotyczą zarówno sieci opartych o przesył komórek (zgodnych z ATM), jak i sieci pakietowych (zgodnych z E-thernetem). Po rozważeniu drugiego z wymienionych typów sieci, wydaje się dzisiaj, iż pakietowe WLANy będą oparte głównie na dwóch standardach, mianowicie: IEEE 802.11 [6]) - wykorzystującym protokół dostępu...
-
Standard deviation as the optimization criterion in the OptD method and its influence on the generated DTM
PublicationReduction of the measurement dataset is one of the current issues related to constantly developing technologies that provide large datasets, eg. laser scanning. It could seems that presence and evolution of processors computer, increase of hard drive capacity etc. is the solution for development of such large datasets. And in fact it is, however, the “lighter” datasets are easier to work with. Additionally, reduced datasets can...
-
Load test of new European record holder in span length among extradosed type bridges
PublicationThe article presents acceptance load tests of a newly built extradosed MS-3 bridge located along the national road DK-16 near Ostróda (Poland). The structure features significant dimension in European reference scale. It is a new record holder in span length regarding this distinct bridge category. Its length ranges 206 m. Static and dynamic load tests were performed here. The program was extended by entire structural laser scanning...
-
Thermographic images during testing measuring instrument boards
Open Research DataThe dataset presents thermografic images acquired during testing the prototype of measuring instrument for resistiometric corrosion monitoring. The testing was performed in the room temperature. VIGOcam v50 thermal imaging camera (VIGO System S.A., Ozarow Mazowiecki, Poland) was used for taking the pictures. These pictures were used as preliminary tests...
-
Optimal configuration of an electrode array for measuring ventricles' contraction
PublicationAn influence of an electrode-array configuration on an impedance signal composition for a fixed spatial distribution of its sources is examined in the paper. The Finite Element Method and Geselowitz relationship were used for examining three different electrode-arrays. A sensitivity approach was used to evaluate each configuration assuming that localization of the signal source is known. A conductivity change, thus the source of...
-
Theoretical description of the measuring method of instantaneous impedance spectra
Publication -
Uncertainty analysis of measuring system for instantaneous power research
PublicationThe paper presents a metrological analysis of the measurement system used for diagnosis of induction motor bearings, based on the analysis of the instantaneous power. This system was implemented as a set of devices with dedicated software installed on a PC. A number of measurements for uncertainty estimation was carried out. The results of the measurements are presented in the paper. The results of the aforementioned analysis helped...
-
Automatic system for measuring shifts and deformation of dental prostheses
Publication -
Methods for Measuring the Intellectual Capital of the Region: Approaches and Assessments
Publication -
The Conditions of Measuring Local Government Units Expenditure Efficiency
Publication -
Voltage Harmonics Measuring Issues in Medium Voltage Systems
PublicationW rozdziale przedstawiono zagadnienia związane z dokładnością pomiarów zniekształceń harmonicznych napięcia z wykorzystaniem przekładników napięciowych w sieciach średnich napięć.
-
Multimedia services applied to noise and hearing monitoring and measuring
PublicationThe goal of this chapter is to show a research study related to processing of data acquired by the multimedia services engineered at the multimedia systems department (MSD) of the Gdansk University of Technology. This concerns a survey on noise threat employing the multimedia noise monitoring system (MNMS) and hearing tests performed by the "I can hear. . . " system. The obtained results of the noise measurements revealed that...
-
Measuring quantum entanglement without prior state reconstruction.
PublicationWykazano, że w przypadku dwóch kubitów splątanie formowania może być mierzone bez rekonstrukcji stanu kwantowego.
-
The high impedance measuring probe for gain-phase analysers.
PublicationAutorzy opracowali tanią sondę pomiarową przeznaczoną do pracy z analizatorami gain-phase jak Solartron 1260 Impedance/Gain-phase Analyser, 1255 Frequency Response Analyser (FRA) lub starszymi wersjami 1250, 1253. Przedstawiona architektura sondy wyznacza jej parametry metrologiczne. Pomiary możliwe są w 8 zakresach obejmujących wartości 100ohm<|Zx|<100Gohm w szerokim zakresie częstotliwości 10uHz-1MHz. Obwód wejściowy sondy pozwala...
-
The method of measuring the energy pass-band of a communication receiver
PublicationPrzedstawiono metodę wyznaczania energetycznego pasma odbiornika radiokomunikacyjnego na podstawie charakterystyki gęstości widmowej mocy szumów własnych na wyjściu odbiornika. Podano numeryczny estymator tego pasma. Wyprowadzono zależności na złożoną niepewność standardową wyznaczania szerokości pasma energetycznego odbiornika.
-
Uncertainty in measuring the power spectrum density of a random signal
PublicationPrzedstawiono sposób oszacowania niepewności wyznaczania gęstości widmowej mocy przebiegu losowego. Przeprowadzono ocenę niepewności estymacji gęstości widmowej mocy biorąc pod uwagę propagację niepewności związanej z rejestracją pojedynczej próbki sygnału w algorytmie cyfrowego przetwarzania sygnału oraz błąd obciążenia estymatora wynikający z zastosowanego modelu matematycznego wielkości wyznaczanej. Wyprowadzono zależności na...
-
A tool for designing water tanks for measuring hydroacoustic transducers
PublicationSpecial water tanks are commonly used to measure the parameters of underwater acoustic systems. They must meet specific requirements, the fulfilment of which ensures very small but acceptable measurement errors. These requirements define the size of the tank and its shape as well as the strong attenuation of reflected waves. At the design stage, it is necessary to determine the impact of the tank structure on the measurement errors...
-
A novel sensor for measuring temperature profile during the thermoablation
PublicationAbstract — A novel approach for monitoring a temperature distribution inside a tissue during thermoablation is presented in the paper. A thermal profile is measured using a set of serially connected thermistors each bypassed by a capacitor. This technique allows a two-wire and simultaneous multi- point measurements using a multi-frequency measurement of electrical impedance. It is...
-
"Food Oxidants and Antioxidants" Book review
PublicationThe book is the 14th title in the CRC series Chemical and Functional Properties of Food Components, edited since 2001 by Zdzisław E. Sikorski. The editor of the book, a professor in the University of Łódź and member of the Polish Academy of Sciences, is an internationally recognized authority in biochemistry and biophysics of reactive oxygen species. In Poland Grzegorz Bartosz has a reputation as the author of his most interesting...
-
Potentiometric taste sensor application for liquid product taste estimation
PublicationThe principles of taste sense and kinds of tastes (sweet, salty, sour, bitter, umami and fat) have been described. Food quality estimation by taste sense: organoleptic testing and sensory analysis has been presented. The principle of operation of potentiometric sensor composed of several Ion Selective Electrodes or All Solid State Electrodes with polymeric membranes and macromolecular chemical compounds sensitive to substances...
-
Disaster-resilient communication networks: Principles and best practices
PublicationCommunication network failures that are caused by disasters, such as hurricanes, arthquakes and cyber-attacks, can have significant economic and societal impact. To address this problem, the research community has been investigating approaches to network resilience for several years. However, aside from well-established techniques, many of these solutions have not found their way into operational...
-
Conception for diagnosing SI engines fed with biofuel in operation conditions
PublicationThe article deals with the question of diagnosing the high power self ignition (SI) engines fed with pro-ecologic fuels in an aspect of appearing operation problems. There has been presented the specific of action and techno-operation profile of the combustion engine foreseen as an investigations object. The preliminary conception of diagnostic investigations of the engine 7L35MC type produced in H. Cegielski - Poznan S.A. factory...
-
An application of simulation model of fuel consumption in diagnostic system of wheeled tractors
PublicationAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnostic is strongly connected with emission demands and does not concern other important vehicle functions. In...
-
Identification of the mechanical properties of the skin by electromechanical impedance analysis of resonant piezoelectric actuator
PublicationThis paper is devoted to the analysis and verification of developed piezoelectric sensor/actuator for measuring the mechanical properties of soft tissues, especially human skin. The key element of the measurement structure is an electromechanical system that uses both the reverse piezoelectric effect (vibration generation – stimulation of the tissues in the appropriate frequency range) and direct piezoelectric effect (system response...
-
Fuctional structure of diagnostic system for wheeled tractors
PublicationAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnosis is strongly connected with emission demands and does not concern other important vehicle functions.In...
-
Selected aspects of the surface quality of the wooden elements after planing
PublicationThe quality of the surface of wooden elements, that have been planed, has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of wooden surface after painting. The emergence of defects in most cases causes need to qualify workpiece as a scrap part or additional work activity must be done. In the paper selected results of the investigation of the effect of the cutting tool wear...
-
Tyre rolling resistance and its influence on fuel consumption
PublicationRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Adaptive Optimal Discrete-Time Output-Feedback Using an Internal Model Principle and Adaptive Dynamic Programming
PublicationIn order to address the output feedback issue for linear discrete-time systems, this work suggests a brand-new adaptive dynamic programming (ADP) technique based on the internal model principle (IMP). The proposed method, termed as IMP-ADP, does not require complete state feedback, merely the measurement of input and output data. More specifically, based on the IMP, the output control problem can first be converted into a stabilization...
-
Pursuing the Deep-Learning-Based Classification of Exposed and Imagined Colors from EEG
PublicationEEG-based brain-computer interfaces are systems aiming to integrate disabled people into their environments. Nevertheless, their control could not be intuitive or depend on an active external stimulator to generate the responses for interacting with it. Targeting the second issue, a novel paradigm is explored in this paper, which depends on a passive stimulus by measuring the EEG responses of a subject to the primary colors (red,...
-
Development of globalization in culture on the example of Europe
PublicationThis article attempts to reflect on the consequences of cultural globalization i.e. the opporturnities and threats that exist it brings with it for existing local cultures. As we know, The processes of globalization contribute to the emergence of any, often contradictory phenomena in the field of culture which influence the existing local cultural systems in various ways. It is assumed that the most important consequence of cultural...
-
Microscale diamond protection for a ZnO coated fiber optic sensor
PublicationFiber optic sensors are widely used in environmental, biological and chemical sensing. Due to the demanding environmental conditions in which they can be used, there is a risk of damaging the sensor measurement head placed in the measuring field. Sensors using nanolayers deposited upon the fiber structure are particularly vulnerable to damage. A thin film placed on the surface of the fiber end-face can be prone to mechanical damage...
-
THE EFFECT OF ALTERNATIVE CUTTER PATHS ON FLATNESS DEVIATIONS IN THE FACE MILLING OF ALUMINUM PLATE PARTS
PublicationIn this paper the relationships between the alternative machining paths and flatness deviations of the aluminum plate part, were presented. The flatness tolerance of the main surface of the plate part has crucial meaning due to the assembly requirement of piezoelectric elements on the radiator. The aluminum bodies under investigation are the base part of the radiators with crimped feathers for the train industry. The surface of...
-
Influence of Natural Conditions on the Imaging of the Bottom of the Gdańsk Bay by Means of the Side Scan Sonar
PublicationThe interest in underwater resources is the reason for the development of modern hydroacoustic systems, including side sonars, which find numerous applications such as: research of seabed morphology and sediment characteristics, preparation of sea sediment maps, and even in special cases of biocenoses such as sea grass meadows, detection of specific targets at the bottom such as shipwrecks, mines, identification of suitable sites...
-
Evaluation of Three Peptide Immobilization Techniques on a QCM Surface Related to Acetaldehyde Responses in the Gas Phase
PublicationThe quartz-crystal microbalance is a sensitive and universal tool for measuring concentrations of various gases in the air. Biochemical functionalization of the QCM electrode allows a label-free detection of specific molecular interactions with high sensitivity and specificity. In addition, it enables a real-time determination of its kinetic rates and affinity constants. This makes QCM a versatile bioanalytical screening tool for...
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublicationThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
Problems and challenges associated with estimating the emissions of organic compounds from indoor materials
PublicationFor several years intensive research has been carried out with the aim of developing a database of the types and amounts of pollutants released from indoor materials to the indoor environment. The paper discusses in detail basic problems and challenges encountered when estimating the emissions of chemical compounds released from of indoor materials. Factors affecting the validity of data obtained by using two different types of...
-
Titania Nanotubes/Hydroxyapatite Nanocomposites Produced with the Use of the Atomic Layer Deposition Technique: Estimation of Bioactivity and Nanomechanical Properties
PublicationTitanium dioxide nanotubes/hydroxyapatite nanocomposites were produced on a titanium alloy (Ti6Al4V/TNT/HA) and studied as a biocompatible coating for an implant surface modification. As a novel approach for this type of nanocomposite fabrication, the atomic layer deposition (ALD) method with an extremely low number of cycles was used to enrich titania nanotubes (TNT) with a very thin hydroxyapatite coating. X-ray diffraction (XRD)...
-
INFLUENCE OF BISMUTH CONTENT ON COMPLEX IMMITTANCE CHARACTERISTICS OF PRESSURELESS SINTERED BiNbO4 CERAMICS
PublicationGoal of the present research was to study immittance properties of BiNbO4 ceramics fabricated by the solid state reaction route followed by pressureless sintering. Four sets of samples were examined, namely the one fabricated from the stoichiometric mixture of oxides, viz. Bi2O3 and Nb2O5 as well as the ones with an excess of 3%, 5% and 10% by mole of Bi2O3. The immittance properties were studied by impedance spectroscopy. Measurements...
-
The Influence of Water and Mineral Oil on Pressure Losses in Hydraulic Motor
PublicationIn this paper, pressure losses in hydraulic motor supplied with water and mineral oil (two liquids that have significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a hydraulic satellite motor that is dedicated to working with different liquids, including water. The methodology of measuring the pressure drop in internal channels of this motor is also...
-
Load carrying capacity of the eccentric joint in the truss made of open cross-sections
PublicationThe influence of eccentricity at intersections of truss members on the load carrying capacity of the truss joint is presented in the paper. The research truss elements were designed as cold-formed open cross section. Analytical calculations, numerical analysis and experimental research were conducted to reveal how the eccentricity affects the effort of material in the joint area. The results of analysis and investigations are compared...
-
The Progress in Electron Microscopy Studies of Particulate Matters to Be Used as a Standard Monitoring Method for Air Dust Pollution
PublicationThe present article reviews studies on air solid particles carried out with the use of electron microscopy. Particle analysis combining scanning and transmission electron microscopy (SEM and TEM) can be used to derive size-resolved information of the composition, mixing state, morphology, and complex refractive index of atmospheric aerosol particles. It seems that electron microscopy is more widely used in atmospheric particulate...
-
Speed sensorless ac drive with inverter output filter and fault detection using load torque signal
PublicationIn this paper, a sensorless induction motor (IM) drive using speed observer system is presented. The system includes load torque computation for gear fault detection. Nonlinear control method is adopted for controlling the motor over a wide speed range. An LC filter for smoothing current and voltage waveforms is used at the output of the voltage inverter. The use of filter imposes more building of the used observer to avoid using...
-
Analysis of temporary steel grandstand with different bracing systems exposed to crowd load
PublicationGrandstands are structures which are regularly subjected to dynamic loads generated by crowd motions. It is a dangerous situation when spectators induce rhythmic jumping, dancing, stamping, etc. If the synchronized movement of spectators excites a natural frequency of the structure, resonant response might occur. To avoid such situations, temporary steel grandstands are commonly strengthened using additional elements that create...
-
The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint
PublicationThe paper presents the results of experimental research of the spatial reinforced concrete deep beam systems orthogonally reinforced and with additional inclined bars. Joint of the deep beams in this research was composed of the longitudinal deep beam with a cantilever suspended at the transversal deep beam. The cantilever deep beam was loaded throughout the depth and the transversal deep beam was loaded at the mid-span by longitudinal...
-
Design of Intelligent Low-Voltage Load Switch for Remote Control System in Smart Grid
PublicationCurrent low-voltage load switches do not support remote disconnect/connect and real-time monitoring of a disconnect/connect state. Addressing to these issues, this paper presents a low-voltage load switch for a smart remote control system, which uses a one-chip microcontroller board and a DC step motor drive mechanism and provides the feedback on the switch status also. Arrears disconnect and full-pay connect control is implemented...
-
Validation of Hydraulic Mechanism during Blowout Trauma of Human Orbit Depending on the Method of Load Application
PublicationThe more we know about mechanisms of the human orbital blowout type of trauma, the better we will be able to prevent them in the future. As long as the buckling mechanism’s veracity is not in doubt, the hydraulic mechanism is not based on equally strong premises. To investigate the correctness of the hydraulic mechanism’s theory, two different methods of implementation of the hydraulic load to the finite element method (FEM) model...
-
Morphology of damage inflicted on brittle polymer in lubricated contact under cyclic static load
PublicationIn this article morphology of damage inflicted on the polymethylmethacrylate (PMMA) plate in static point lubricated contact with a ball made of five different materials under cyclic normal load has been presented. It is argued that the counterface material and lubricating film play an important role in the damage process and the extent of damage inflicted in the PMMA plate.