Search results for: LINEAR LOW-DENSITY POLYETHYLENE
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublicationWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Application of Artificial Neural Networks to Predict Insulation Properties of Lightweight Concrete
PublicationPredicting the properties of concrete before its design and application process allows for refining and optimizing its composition. However, the properties of lightweight concrete are much harder to predict than those of normal weight concrete, especially if the forecast concerns the insulating properties of concrete with artificial lightweight aggregate (LWA). It is possible to use porous aggregates and precisely modify the composition...
-
Method for the simultaneous determination of monoaromatic and polycyclic aromatic hydrocarbons in industrial effluents using dispersive liquid-liquid microextraction with GC-MS
PublicationWe present a new method for simultaneous determination of 22 monoaromatic and polycyclic aromatic hydrocarbons in postoxidative effluents from the production of petroleum bitumen using dispersive liquid-liquid microextraction coupled to gas chromatography and mass spectrometry. The eight extraction parameters including the type and volume of extraction and disperser solvent, pH, salting out effect, extraction and centrifugation...
-
Rotor-Flux Vector based Observer of Interior Permanent Synchronous Machine
PublicationThe sensorless control system of the interior permanent magnet machine is considered in this paper. The control system is based on classical linear controllers. In the machine, there occurs non-sinusoidal distribution of rotor flux together with the slot harmonics, which are treated as the control system disturbances. In this case, the classical observer structure in the (d-q) is unstable for the low range of rotor speed resulting...
-
Effect of dendrimer-based interlayers for enzyme immobilization on a model electrochemical sensing system for glutamate
PublicationIn this paper, we discuss dendrimer usage in enzyme-based electrochemical biosensors, particularly with respect to biomolecule loading on the sensing surface. A novel approach to design bioactive layers with immobilized enzymes for electrochemical biosensors using the surface plasmon resonance (SPR) method in combination with electrochemical impedance spectroscopy was presented. The gold surface was modified with linear linkers...
-
Efficiency of gas detection algorithms using fluctuation enhanced sensing
PublicationEfficiency of various gas detection algorithms by applying fluctuation enhanced sensing method was discussed. We have analyzed resistance noise observed in resistive WO3- nanowires gas sensing layers. Power spectral densities of the recorded noise were used as the input data vectors for two algorithms: the principal component analysis (PCA) and the support vector machine (SVM). The data were used to determine gas concentration...
-
Influence of Protonation State on the Excited State Dynamics of a Photobiologically Active Ru(II) Dyad
PublicationThe influence of ligand protonation on the photophysics of a ruthenium (Ru) dyad bearing the 2-(1-pyrenyl)-1H-imidazo[4,5-f][1,10]-phenanthroline (ippy) ligand was investigated by time-resolved transient absorption spectroscopy. It was found that changes in the protonation state of the imidazole group led to changes in the electronic configuration of the lowest lying excited state. Formation of the fully deprotonated imidazole...
-
Positron-electron correlation-polarization potentials for the calculation of positron collisions with atoms and molecules
PublicationWe present correlation-polarization potentials for the calculation of scattering cross sections of positrons with atoms and molecules. The potentials are constructed from a short-range correlation term and a long-range polarization term. For the short-range correlation term we present four different potentials that are derived from multi-component density functionals. For the long-range polarization term we employ a multi-term...
-
Spatial aspects of urban air quality management: Estimating the impact of micro-scale urban form on pollution dispersion
PublicationUrban planning and design solutions affect urban ventilation conditions, thus mitigating the effects of atmospheric pollution. However, these findings are not being implemented in the planning practice to a sufficient extent, partly due to the lack of specific guidelines. Moreover, many urban air quality monitoring (AQM) sites have low represnentativeness and thus do not provide comprehensive data for effective urban air pollution control...
-
Influence of Surface Modification of Titanium and Its Alloys for Medical Implants on Their Corrosion Behavior
PublicationTitanium and its alloys are often used for long-term implants after their surface treatment. Such surface modification is usually performed to improve biological properties but seldom to increase corrosion resistance. This paper presents research results performed on such metallic materials modified by a variety of techniques: direct voltage anodic oxidation in the presence of fluorides, micro-arc oxidation (MAO), pulse laser treatment,...
-
Optical and electrical properties of boron doped diamond thin conductive films deposited on fused silica glass substrates
PublicationThis paper presents boron-doped diamond (BDD) film as a conductive coating for optical and electronic purposes. Seeding and growth processes of thin diamond films on fused silica have been investigated. Growth processes of thin diamond films on fused silica were investigated at various boron doping level and methane admixture. Two step pre-treatment procedure of fused silica substrate was applied to achieve high seeding density....
-
The Dominant Influence of Plastic Deformation Induced Residual Stress on the Barkhausen Effect Signal in Martensitic Steels
PublicationThe paper presents the results of investigation of the influence of plastic deformation on the magnetic properties of martensitic steel (P91 grade). The properties of the hysteresis loops as well as of the Barkhausen effect (BE) signal are analysed for both tensile and compressive loading up to ε = 10% of plastic deformation. The choice of the steel and of the deformation range is unique, since for such combination one can expect...
-
Evaluation of position estimation based on accelerometer data
PublicationThe paper concerns the problem of integrating data from accelerometers. A suitable model of a MEMS accelerometer is presented which is a part of inertial measurement units (IMU). Such units allow to measure orientation as well as to localize systems. They also appear to be applicable for systems positioning. The main purpose of the paper is to discuss conditions that must be satisfied to calculate the location of the sensor by...
-
UV Light-Modulated Fluctuation-Enhanced Gas Sensing by Layers of Graphene Flakes/TiO2 Nanoparticles
PublicationWe present experimental results of fluctuation-enhanced gas sensing by low-cost resistive sensors made of a mixture of graphene flakes and TiO2 nanoparticles. Both components are photocatalytic and activated by UV light. Two UV LEDs of different wavelengths (362 and 394 nm) were applied to modulate the gas sensing of the layers. Resistance noise was recorded at low frequencies, between 8 Hz and 10 kHz. The sensors’ response was...
-
Understanding the Dominant Physics Mechanisms on the p-i-n Perovskite Solar Cells Fabricated by Scalable Slot-Die Coating Process in Ambient Air
PublicationPerovskite solar cells (PSC) are emerging technologies that have shown continuous improvement in power conversion efficiency (PCE) and stability. However, a very important aspect that has been seldom considered is the reproducibility of PCE of PSC devices. It is possible to achieve PCE from 10.21% to 17.05% using scalable slot-die-coating technique. However, a spatial distribution of performance is clearly observed for device samples...
-
Conductive Thermoplastic Polyurethane Nanocomposite Foams Derived from a Cellulose/MWCNTs Aerogel Framework: Simultaneous Enhancement of Piezoresistance, Strength, and Endurance
PublicationHigh conductivity and excellent mechanical properties of composite polymers favors their application as piezoresistive strain sensors. Nonetheless, it is difficult to develop composite polymers with desirable piezoresistance, mechanicaland durable properties. Herein, we developed conductive cellulose/MWCNTs aerogel using the freeze-drying technique. Besides, we explored the application of the highly-sensitive piezoresistive polymer...
-
Biophotonic low-coherence sensors with boron-doped diamond thin layer
PublicationLow-coherence sensors using Fabry-Perot interferometers are finding new applications in biophotonic sensing, especially due to the rapid technological advances in the development of new materials. In this paper we discuss the possibility of using boron-doped nanodiamond layers to protect mirror in a Fabry-Perot interferometer. A low-coherence sensor using Fabry-Perot interferometer with a boron-doped nanodiamond (B-NCD) thin protective...
-
Correlation–polarization effects in electron/positron scattering from acetylene: A comparison of computational models
PublicationDifferent computational methods are employed to evaluate elastic (rotationally summed) integral and differential cross sections for low energy (below about 10 eV) positron scattering off gas-phase C2H2 molecules. The computations are carried out at the static and static-plus-polarization levels for describing the interaction forces and the correlation–polarization contributions are found to be an essential component for the correct...
-
A memory efficient and fast sparse matrix vector product on a Gpu
PublicationThis paper proposes a new sparse matrix storage format which allows an efficient implementation of a sparse matrix vector product on a Fermi Graphics Processing Unit (GPU). Unlike previous formats it has both low memory footprint and good throughput. The new format, which we call Sliced ELLR-T has been designed specifically for accelerating the iterative solution of a large sparse and complex-valued system of linear equations arising...
-
Response of a New Low-Coherence Fabry-Perot Sensor to Hematocrit Levels in Human Blood
PublicationIn this paper, a low-coherence Fabry-Perot sensor with a spectrally measured signal processing response to the refractive index of liquids is presented. Optical fiber sensors are potentially capable of continuous measuring hematocrit levels in blood. Low-coherence Fabry-Perot interferometric sensors offer a robust solution, where information about the measurand is encoded in the full spectrum of light reflected from the sensing...
-
Modification of TiO2 nanotubes by graphene–strontium and cobalt molybdate perovskite for efficient hydrogen evolution reaction in acidic medium
PublicationHerein, we demonstrate that modification of TiO2 nanotubes with graphene–strontium and cobalt molybdate perovskite can turn them into active electrocatalysts for hydrogen evolution reaction (HER). For this purpose, a simple method of hydrothermal synthesis of perovskites was developed directly on the TiO2 nanotubes substrate. Moreover, the obtained hybrids were also decorated with graphene oxide (GO) during one-step hydrothermal...
-
Comparison of different one-parameter damage laws and local stress-strain approaches in multiaxial fatigue life assessment of notched components
PublicationThis paper aims to compare the predictive capabilities of different one-parameter damage laws and local stress-strain approaches to assess the fatigue lifetime in notched components subjected to proportional bending-torsion loading. The tested fatigue damage parameters are defined using well-known stress-based, strain-based, SWT-based and energy-based relationships. Multiaxial cyclic plasticity at the notch-controlled process zone...
-
Nickel-nanodiamond coatings electrodeposited from tartrate electrolyte at ambient temperature
PublicationIn this study, nanocrystalline Ni and Ni-diamond coatings were obtained by electrodeposition from tartrate electrolyte at ambient temperature aiming at improving corrosion and wear properties of the material. The created surfaces were investigated with regard to microhardness, adhesion, wear- and corrosion-resistance. The various methods such as atomic force microscopy, scanning electron microscopy, electrochemical impedance spectroscopy...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublicationThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
Analogue GPS repeater
PublicationThis article concerns the problem of difficulty in correct indoor Global Positioning System (GPS) signals reception due to attenuation. Radio signal repeaters are proposed as means to solve this problem. Firstly, the GPS signal characteristics are described, emphasizing their low power in the point of reception. In the second part, various applications of GPS signal repeater, where indoor GPS signals reception is required, are...
-
Antimony substituted lanthanum orthoniobate proton conductor – structure and electronic properties.
PublicationX‐ray and neutron diffraction have been utilized to analyze the crystalline and electronic structure of lanthanum orthoniobate substituted by antimony. Using X‐ray absorption spectroscopy and photoelectron spectroscopy, changes in the electronic structure of the material upon substitution have been analyzed. The structural transition temperature between fergusonite and scheelite phases for 30 mol% antimony substitution was found...
-
Low-frequency noise in ZrS3 van der Waals semiconductor nanoribbons
PublicationWe report the results of the investigation of low-frequency electronic noise in ZrS3 van der Waals semiconductor nanoribbons. The test structures were of the back-gated field-effect-transistor type with a normally off n-channel and an on-to-off ratio of up to four orders of magnitude. The current–voltage transfer characteristics revealed significant hysteresis owing to the presence of deep levels. The noise in ZrS3 nanoribbons...
-
Pulsed UV-irradiated Graphene Sensors for Ethanol Detection at Room Temperature
PublicationA graphene-based gas sensor fabricated in a FET (GFET) configuration and its sensitivity towards ethanol and methane is reported. Detection of ethanol at the level of 100 ppm was observed under pulsed UV irradiation and after cleaning by UV light in the N2 ambient. Reduction of the frequency of UV irradiation pulses resulted in increased changes in sensor resistance in the presence of ethanol. Improved sensing behavior was ascribed...
-
Optical Sensor Based Gestures Inference Using Recurrent Neural Network in Mobile Conditions
PublicationIn this paper the implementation of recurrent neural network models for hand gesture recognition on edge devices was performed. The models were trained with 27 hand gestures recorded with the use of a linear optical sensor consisting of 8 photodiodes and 4 LEDs. Different models, trained off-line, were tested in terms of different network topologies (different number of neurons and layers) and different effective sampling frequency...
-
Właściwości elektryczne szkło-ceramiki zawierającej ferroelektryczną fazę BiV
PublicationKompozyty szklano - ceramiczne zawierające nanokryształy posiadają właściwości fizyczne, które nie są możliwe do uzyskania w innych materiałach. Dzięki możliwości wytworzenia szkło - ceramik posiadających kryształy o różnej wielkości (nano, mikro...) i różnorodnego typu, można w istotny sposób kontrolować właściwości elektryczne takich materiałów. Stała dielektryczna faz ferroelektrycznych jest bardzo wrażliwa na zmiany rozmiarów...
-
Why the Solvation Water around Proteins Is More Dense than Bulk Water
PublicationThe main aim of this work is to propose a rational explanation of the commonly observed phenomenon of increasing water density within solvation shell of proteins. We have observed that the geometry of the water–water hydrogen bond network within solvation layer differs from the one in bulk water, and it is the result of interactions of water molecules with protein surface. Altered geometry of the network reflects changes in the...
-
Why the solvation water around proteins is more dense than bulk water
PublicationThe main aim of this work is to propose a rational explanation of commonly observed phenomenon of increasing water density within solvation shell of proteins. We have observed that geometry of the water-water hydrogen bond network within solvation layer differs from the one in bulk water and it is the effect of interactions of water molecules with protein surface. Altered geometry of the network reflects changes in the structure...
-
Linear impedance of 50(2Bi2O3-V2O5)-50SrB4O7 glass-ceramic heat-treated at 613 K measured with impedance spectroscopy method at high temperature region
Open Research DataThe linear electrcial properties of 50(2Bi2O3-V2O5)-50SrB4O7 glass-ceramic heat-treated at 613 K was measured by impedance spectroscopy method.
-
Measurements of the mechanical system properties of "SpeedLine magnetic" ultra-fast robot prototype for IML labeling
Open Research DataThe mechanical system tests of the high-speed IML labeling robot "SpeedLine Magnetic" were carried out in order to analyze the effects of the drive system's operating parameters on vibration and noise.
-
A simplified channel estimation procedure for NB-IoT downlink
PublicationThis paper presents a low-complexity channel estimation procedure which is suitable for use in energy-efficient NB-IoT user equipment devices. The procedure is based on the well-established least squares scheme, followed by linear interpolation in the time domain and averaging in the frequency domain. The quality of channel estimation vs. signal-to-noise ratio is evaluated for two channel models and compared with the performance...
-
Features of Nonlinear Sound Propagation in Vibrationally Excited Gases
PublicationWeakly nonlinear sound propagation in a gas where molecular vibrational relaxation takes place is studied. New equations which govern the sound in media where the irreversible relaxation may take place are derived and discussed. Their form depends on the regime of excitation of oscillatory degrees of freedom, equilibrium (reversible) or non-equilibrium (irreversible), and on the comparative frequency of the sound in relation to...
-
Monitoring of n-butanol vapors biofiltration process using an electronic nose combined with calibration models
PublicationMalodours, by definition, are generally unpleasant, nuisance smells that are a mixture of volatile chemical compounds which can be perceptible even at low concentrations. Due to the more frequent occurrence of odour nuisance associated with the odour sensations, and thus the need to remove them from the air, deodorization techniques are commonly used. Biofiltration is one of the methods of reducing odorants in the air stream. In...
-
Rapid development of the photoresponse and oxygen evolution of TiO2 nanotubes sputtered with Cr thin films realized via laser annealing
PublicationRecently, earth abundant transition metal oxides have gained particular attention as potential catalyst candidates due to their availability and low-cost comparing to substrates containing precious Pt or Au species. Herein, we present characterization of morphology, structure and electrochemical properties of pulsed 532 nm laser treated TiO2 nanotubes (NT) sputtered by the thin film of chromium. Scanning electron microscopy enables...
-
Influence of Urea and Dimethyl Sulfoxide on K-Peptide Fibrillation
PublicationProtein fibrillation leads to formation of amyloids—linear aggregates that are hallmarks of many serious diseases, including Alzheimer’s and Parkinson’s diseases. In this work, we investigate the fibrillation of a short peptide (K-peptide) from the amyloidogenic core of hen egg white lysozyme in the presence of dimethyl sulfoxide or urea. During the studies, a variety of spectroscopic methods were used: fluorescence spectroscopy...
-
The Issue of Shading Photovoltaic Installation Caused by Dust Accumulation on the Glass Surface
PublicationThe issue of accumulation of dust and other pollutants on the surface of photovoltaic modules was thoroughly analysed over the years. One of the first surveys in this field of knowledge linked pollutant accumulation on the module surface with transmittance loss of its glass covering, which leads to lessened amount of solar radiation reaching solar cells. First stage of this accumulation process is linear transparency loss, and second...
-
Testing of Software for the Planning of a Linear Object GNSS Measurement Campaign under Simulated Conditions
PublicationThe precision of a linear object measurement using satellite techniques is determined by the number and the relative position of the visible satellites by the receiver. The status of the visible constellation is described by DOP. The obtained geometric coefficient values are dependent on many variables. When determining these values, field obstacles at the receiver location and satellite positions changing with time must be taken...
-
Dirac fermions and possible weak antilocalization in LaCuSb2
PublicationLayered heavy-metal square-lattice compounds have recently emerged as potential Dirac fermion materials due to bonding within those sublattices. We report quantum transport and spectroscopic data on the layered Sb square-lattice material LaCuSb2. Linearly dispersing band crossings, necessary to generate Dirac fermions, are experimentally observed in the electronic band structure observed using angle-resolved photoemission spectroscopy,...
-
IMPACT OF DIRECT CURRENT ON NITRIFYING BIOMASS
PublicationEffects of short term exposure of nitrifying biomass to direct current were studied. DC was applied to mixed liquor from municipal BNR plant using graphite electrodes in no substrate limiting conditions. Both, ammonia oxidizing bacteria (AOB) and nitrite oxidizing bacteria (NOB) populations were affected by the current, however in opposite ways. The AOB population activity was inhibited by applied voltage. Activity decrease was...
-
On the relationship between the structural and volumetric properties of solvated metal ions in O-donor solvents using new structural data in amide solvents
PublicationThe structures of the N,N-dimethylformamide (dmf), N,N-dimethylacetamide (dma), and N,N-dimethylpropionamide (dmp) solvated strontium and barium ions have been determined in solution using large angle X-ray scattering and EXAFS spectroscopy. The strontium ion has a mean coordination number (CN) between 6.2 and 6.8, and the barium ion has a mean CN between 7.1 and 7.8 in these amide solvents. The non-integer numbers indicates that...
-
Evaluation of Response Amplitude Operator of Ship Roll Motions Based on the Experiments in White Noise Waves
PublicationEvaluation of the response amplitude operator (RAO) function for ship wave frequency motions by means of scale model tests in regular waves is a standard procedure conducted by hydrodynamic model testing institutions. The resulting RAO function allows for evaluating sufficiently reliable seakeeping predictions for low to moderate sea states. However, for standard hull forms, correct prediction of roll motion in irregular wave (and...
-
Superconductivity–Electron Count Relationship in Heusler Phases─the Case of LiPd2Si
PublicationWe report superconductivity in the full Heusler compound LiPd2Si (space group Fm3̅m, No. 225) at a critical temperature of Tc = 1.3 K and a normalized heat capacity jump at Tc, ΔC/γTc = 1.1. The low-temperature isothermal magnetization curves imply type-I superconductivity, as previously observed in LiPd2Ge. We show, based on density functional theory calculations and using the molecular orbital theory approach, that while LiPd2Si...
-
Cascading transitions toward unconventional charge density wave states in the quasi-two-dimensional monophosphate tungsten bronze P4W16O56
PublicationSingle crystals of the m = 8 member of the low-dimensional monophosphate tungsten bronzes (PO2)4(WO3)2m family were grown by chemical vapour transport technique and the high crystalline quality obtained allowed a reinvestigation of the physical and structural properties. Resistivity measurements revealed three anomalies at TC1 = 258 K, TC2 = 245 K and TC3 = 140 K, never observed until now. Parallel X-ray diffraction investigations...
-
Carboxylation Enhances Fragmentation of Furan upon Resonant Electron Attachment
PublicationWe report a dissociative electron attachment study to 2-furoic acid (C5H4O3) isolated in a gas phase, which is a model molecule consisting of a carboxylic group and a furan ring. Dissociation of furan by low energy electrons is accessible only via electronic excited Feshbach resonances at energies of incident electrons above 5 eV. On the other hand, carboxylic acids are well- known to dissociate via attachment of electrons at subexcitation energies....
-
Non-linear impedance of V2O5 nanorods obtained at 923K
Open Research DataThe DataSet contains the non-linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
-
Effects of Ni-NCAL and Ni–Ag electrodes on the cell performances of low-temperature solid oxide fuel cells with Sm0.2Ce0·8O2-δ electrolyte at various temperatures
PublicationThree low-temperature solid oxide fuel cells are built using Sm0.2Ce0·8O2-δ (SDC) as the electrolyte. Cell A is symmetrical and features Ni–LiNi0.8Co0·15Al0·05O2 (Ni–NCAL) electrodes, Cell B comprises a Ni–NCAL anode and a Ni–Ag cathode, and Cell C is fabricated using a Ni–NCAL cathode and a Ni–Ag anode. The ohmic resistance and polarization resistance (Rp) of Cells B and C are significantly higher than those of Cell A. The reduction...