Filters
total: 895
filtered: 870
Search results for: EFFECTIVENES
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublicationThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Concept of 'Good Urban Governance' and Its Application in Sustainable Urban Planning
PublicationContemporary urban theory and practice in the post-industrial era is increasingly often turning towards an approach based on sustainable development. That concept bearing the traits of a paradigm has grown on the ground of broad quest for an alternative to the existing development model of the industrial civilisation. It has gained wide social acceptance and is the basis for many development and environmental programmes at the...
-
Spectral Finite Element Method in Condition Monitoring and Damage Detection
PublicationIt is well known that the dynamic behaviour of engineering structures may carry very important and crucial information that can be further used for the assessment of their condition as well as detection of any damage induced. The current interest in monitoring techniques based on the propagation of guided elastic waves requires that numerical techniques used for modelling the phenomena associated must shift into the realm of high...
-
Diamond-based protective layer for optical biosensors
PublicationOptical biosensors have become a powerful alternative to the conventional ways of measurement owing to their great properties, such as high sensitivity, high dynamic range, cost effectiveness and small size. Choice of an optical biosensor's materials is an important factor and impacts the quality of the obtained spectra. Examined biological objects are placed on a cover layer which may react with samples in a chemical, biological...
-
Laboratory station for research of the innovative dry method of exhaust gas desulfurization for an engine powered with residual fuel
PublicationContemporary methods of exhaust gas desulfurization in marine engines are all expensive methods (4-5 million euro). This is, among other reasons, due to the limited market audience, but primarily due to the monop-olized position of manufacturers offering fabrication and assembly of this type of marine ship installations. Proposed as part of a research project financed by the Regional Fund for Environmental Protection and Maritime...
-
Advanced polarization sensitive analysis in optical coherence tomography
PublicationThe optical coherence tomography (OCT) is an optical imaging method, which is widely applied in variety applications. This technology is used to cross-sectional or surface imaging with high resolution in non-contact and non-destructive way. OCT is very useful in medical applications like ophthalmology, dermatology or dentistry, as well as beyond biomedical fields like stress mapping in polymers or protective coatings defects detection....
-
Criteria for evaluation and selection of the best offer for the Contract Engineer service
PublicationThe purpose of the legal regulations regarding public procurement in EU countries is to ensure effective funds' spending. When assessing and selecting the best offer, the contracting entities have at their disposal many different criteria, including non-price criteria. Their proper selection and application is necessary to ensure the high quality of the ordered product, delivery or service. Making an order for intellectual services,...
-
Force transfer and stress distribution in short cantilever deep beams loaded throughout the depth with a various reinforcement
PublicationDeep beams used as the main reinforced concrete structural elements which taking over the load and stiffening construction are often found in high-rise buildings. The architecture of these buildings is sometimes sophisticated and varied, arouse the admiration of the majority of recipients, and thus causing an engineering challenge to correctly design the structural system and force transfer. In such structures is important to shape...
-
Opitmalising Human Development Index with sensitivity analysis
PublicationResearch background: Composite indicators are commonly used not only to measure economic development, the standard of livin g, competitiveness, fairness, effectiveness but are also willingly implemented in to many different fields. How- ever, it seems that in most cases the variable weig hting procedure is avoided or erroneous since in most cases so-called “wights by belief” are...
-
Implementation of Hermite-Ritz method and Navier’s Technique for Vibration of Functionally Graded Porous Nanobeam Embedded in Winkler-Pasternak Elastic Foundation Using bi-Helmholtz type of nonlocal elasticity
PublicationPresent study is devoted to investigating the vibration characteristics of Functionally Graded (FG) porous nanobeam embedded in an elastic substrate of Winkler-Pasternak type. Classical beam theory (CBT) or Euler-Bernoulli beam theory (EBT) has been incorporated to address the displacement of the FG nanobeam. Bi-Helmholtz type of nonlocal elasticity is being used to capture the small scale effect of the FG nanobeam. Further, the...
-
Compressive Sensing Approach to Harmonics Detection in the Ship Electrical Network
PublicationThe contribution of this paper is to show the opportunities for using the compressive sensing (CS) technique for detecting harmonics in a frequency sparse signal. The signal in a ship’s electrical network, polluted by harmonic distortions, can be modeled as a superposition of a small number of sinusoids and the discrete Fourier transform (DFT) basis forms its sparse domain. According to the theory of CS, a signal may be reconstructed...
-
Synergistic effects of hybrid advanced oxidation processes (AOPs) based on hydrodynamic cavitation phenomenon – A review
PublicationHigh-performance water treatment systems based on cavitational processes have received an increasing interest of scientific community in the past few decades. Numerous studies indicated the advantageous application of hydrodynamic cavitation as an alternative, reagent-free treatment method of various pollutants in water. Both approaches were proved as an effective method to achieve mineralization of many organic contaminants as...
-
Cavitation-Based Processes for Water and Wastewater Treatment
PublicationCavitation based on advanced oxidation processes (Cav-AOPs) is interesting alternatives for already implemented wastewater treatment technologies. Destructive and strongly undesirable phenomena in the industry, i.e., cavitation, revealed to be useful in a positive manner as a source of energy for chemical reactions. During the implosion of cavitation bubbles, focused energy and resulting high temperature and pressure allows to...
-
Mitigation effect of face shield to reduce SARS-CoV-2 airborne transmission risk: Preliminary simulations based on computed tomography
PublicationWe aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence...
-
Sustainable development model for measuring and managing sustainability in the automotive sector
PublicationA growing number of organizations across a variety of industries are now pursuing sustainable management business goals to improve business efficiency, manage stakeholder expectations, or for legislative compliance. This is also the case for automotive manufacturing organizations who are under pressure from their stakeholders to manage and improve sustainability performance. This requires the development of credible measurement...
-
Worm Gear Drives with Improved Kinematic Accuracy
PublicationThis paper presents the fundamentals of the design and applications of new worm gear drive solutions, which enable the minimisation of backlash and are characterised by higher kinematic accuracy. Different types of worm surfaces are briefly outlined. Technological problems concerning the principles of achieving a high degree of precision in machining are also described. Special attention is paid to the shaping of conical helical...
-
Comparative study on total nitrogen prediction in wastewater treatment 1 plant and effect of various feature selection methods on machine learning algorithms performance
PublicationWastewater characteristics prediction in wastewater treatment plants (WWTPs) is valuable and can reduce the number of sampling, energy, and cost. Feature Selection (FS) methods are used in the pre-processing section for enhancing the model performance. This study aims to evaluate the effect of seven different FS methods (filter, wrapper, and embedded methods) on enhancing the prediction accuracy for total nitrogen (TN) in the WWTP...
-
Serotonergic–Muscarinic Interaction within the Prefrontal Cortex as a Novel Target to Reverse Schizophrenia-Related Cognitive Symptoms
PublicationRecent studies revealed that the activation of serotonergic 5-HT1A and muscarinic M1, M4, or M5 receptors prevent MK-801-induced cognitive impairments in animal models. In the present study, the effectiveness of the simultaneous activation of 5-HT1A and muscarinic receptors at preventing MK-801-induced cognitive deficits in novel object recognition (NOR) or Y-maze tests was investigated. Activators of 5-HT1A (F15599), M1 (VU0357017),...
-
CaO-based high temperature CO2 sorbents – Literature review
PublicationThe use of CaO-based adsorbents has a high potential to capture CO2 from various systems due to its high reactivity with CO2, high capacity, and low cost of naturally derived CaO. The application of CaO-based sorbents to remove carbon dioxide is based on a reversible reaction between CaO and CO2. However, multiple carbonation/calcination cycles lead to a rapid reduction in the sorption capacity of natural CaO, and therefore efforts...
-
WYKORZYSTANIE TESTU MUSHRA W BADANIU KORZYŚCI UŻYTKOWANIA PROTEZ SŁUCHOWYCH
PublicationOcena jakości dopasowania aparatów słuchowych w kontekście korzyści, jakie może przy-nieść proteza jest złożonym zagadnieniem. Obiektywne parametry aparatów, które można wy-znaczyć (np. wzmocnienie czy pasmo przenoszenia) nie zawsze mają bezpośredni i decydujący wpływ w subiektywnej ocenie jakości dopasowania protezy słuchowej przez pacjenta. Pomiary efektywności aparatu słuchowego mogą dotyczyć wielu aspektów, między innymi kompensacji...
-
System wykrywania i przeciwdziałania spoofingowi GPS
PublicationSpoofing w systemach nawigacji satelitarnej jest atakiem elektronicznym, który polega na nieuprawnionej emisji sygnałów stanowiących imitacje rzeczywistych sygnałów odbieranych z satelitów. Powoduje on wyznaczenie nieprawidłowych informacji o czasie, położeniu i prędkości odbiornika. Z uwagi na trudność jego wykrycia, spoofing stanowi poważniejsze zagrożenie niż proste zagłuszanie sygnałów zakłóceniem o dużej mocy (ang. jamming)....
-
Metoda TrustCritic oceny wiarygodności sklepów internetowych
PublicationW artykule przedstawiono metodę oceny wiarygodności sklepów internetowych TrustCritic. Powszechnie występujące nadużycia w handlu elektronicznym sprawiają, że zaufanie do przedsiębiorcy staje się kluczowym czynnikiem decyzji konsumentów. Przedsiębiorca narażony jest na niezgodność z prawem, utratę wizerunku i klientów. Artykuł omawia problematykę nadużyć w sferze e-biznesu oraz proponuje wielokryterialny model oceny sklepu internetowego,...
-
Improved surface coverage of an optical fibre with nanocrystalline diamond by the application of dip-coating seeding
PublicationGrowth processes of diamond thin films on the fused silica optical fibres (10 cm in length) were investigated at various temperatures. Fused silica pre-treatment by dip-coating in a dispersion consisting of detonation nanodiamond (DND) in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) was applied. Nanocrystalline diamond (NCD) films were deposited on the fibres using the microwave plasma assisted chemical vapour deposition...
-
Integration of electric vehicle into smart grid: a meta heuristic algorithm for energy management between V2G and G2V
PublicationRecently, Electric Vehicles (EV) have been providing fast response and substantial progress in the power generation model. Further, EVs are exploited as adaptable Energy Storage Systems (ESSs) and show a promising performance in ancillary service markets to increase the demand of Smart Grid (SG) integration. The expansion of Vehicle-to-Grid concept has created an extra power source when renewable energy sources are not available....
-
ZnO-decorated green-synthesized multi-doped carbon dots from Chlorella pyrenoidosa for sustainable photocatalytic carbamazepine degradation
PublicationThe promising green synthesis of carbon dots (CDs) from microalga Chlorella pyrenoidosa was achieved using simple hydrothermal and microwave-assisted methods. Doping of nanomaterials by nonmetals (N, S, and P) was confirmed by X-ray photoelectron spectroscopy (XPS), while the existence of metals in the CDs was confirmed by inductively coupled plasma optical emission spectroscopy (ICP-OES) and transmission electron microscopy (TEM),...
-
Bioreactors and biophoton-driven biohydrogen production strategies
PublicationGiven the current issues with global warming and rising greenhouse gas emissions, biohydrogen is a viable alternative fuel option. Technologies to produce biohydrogen include photo fermentation, dark fermentation, direct and indirect bio-photolysis, and two-stage fermentation. Biological hydrogen generation is a green and promising technique with mild reaction conditions and low energy consumption compared to thermochemical and...
-
Efficacy of intralesional bleomycin in treatment resistant viral warts
PublicationIntroduction Optimal management of treatment-refractory viral warts caused by human papillomavirus is unknown. One of the treatment methods is intralesional bleomycin solution. Objective To determine risk factors for resistant viral warts (not responding to conventional treatments for ≥ 6 months), to determine the effectiveness and safety of intralesional bleomycin in a group of patients with viral warts resistant to conventional...
-
Prediction of maximum tensile stress in plain-weave composite laminates with interacting holes via stacked machine learning algorithms: A comparative study
PublicationPlain weave composite is a long-lasting type of fabric composite that is stable enough when being handled. Open-hole composites have been widely used in industry, though they have weak structural performance and complex design processes. An extensive number of material/geometry parameters have been utilized for designing these composites, thereby an efficient computational tool is essential for that purpose. Different Machine Learning...
-
Hydrochar-nanoparticle integration for arsenic removal from wastewater: Challenges, possible solutions, and future horizon
PublicationArsenic (As) contamination poses a significant threat to human health, ecosystems, and agriculture, with levels ranging from 12 to 75% attributed to mine waste and stream sediments. This naturally element is abundant in Earth's crust and gets released into the environment through mining and rock processing, causing ≈363 million people to depend on As-contaminated groundwater. To combat this issue, introducing a sustainable hydrochar...
-
Catalytic activity of Ni-MgAl2O4 modified with transition metal (Ti, Mo, W) carbides as potential catalysts for resource recovery via dry reforming of waste plastics
PublicationThe growing amounts of plastic waste and CO2 emissions are two environmental threats that require urgent attention. Pyrolysis combined with dry reforming (PCDR) is a technology that allows both CO2 utilization and resource recovery from waste plastic. New catalysts for PCDR are crucial for developing efficient and stable processes that can be widely implemented in the industry. In this study, Ni/MgAl2O4 catalysts modified using different...
-
Longitudinal drug synergy assessment using convolutional neural network image-decoding of glioblastoma single-spheroid cultures
PublicationAbstract Background In recent years, drug combinations have become increasingly popular to improve therapeutic outcomes in various diseases, including difficult to cure cancers such as the brain cancer glioblastoma. Assessing the interaction between drugs over time is critical for predicting drug combination effectiveness and minimizing the risk of therapy resistance. However, as viability readouts of drug combination experiments...
-
Pedestrian Safety at Midblock Crossings on Dual Carriageway Roads in Polish Cities
PublicationRoad crossings across two or more lanes in one direction are particularly dangerous due to limited sight distance and high vehicle speeds. To improve their safety, road authorities should provide safety treatments. These may include additional measures to reduce speed and narrow the road cross-section and the introduction of active pedestrian crossings. Equipped with flashing lights activated automatically when a pedestrian is...
-
Hydrothermal modification of TiO2 nanotubes in water and alkali metal electrolytes (LiNO3, NaNO3, KNO3) – Direct evidence for photocatalytic activity enhancement
PublicationThe influence of hydrothermal annealing (HA) of TiO2 nanotubes (TiO2-NTs) in various baths (H2O, LiNO3, NaNO3, KNO3 performed for 4 h, 24 h, 64 h), on their photocatalytic and photoelectrocatalytic properties, was studied. The use of electrolytes was to enable the monitoring of photoactivity changes as a result of the expected impact on the population of hydroxyl groups on the surface. The assumption turned out to be correct and...
-
COOPERATION BETWEEN UNIVERSITY AND EXTERNAL COMPANY IN ARCHITECTURAL INVENTORY USING INNOVATIVE MEASURING TECHNOLOGY
PublicationArchitectural inventories are the main field for using innovative technology ( remote sensing). The main purpose of using ie. Laser scanning or photogrammetry is to capture all of the important details of structure. Regarding the extents of inventory works, it may only apply to external details, such as facades, supporting structures and surroundings, whilst in terms of advanced inventory, the building's interior is also expected...
-
Influence of the boron doping level on the electrochemical oxidation of raw landfill leachates: advanced pre-treatment prior to the biological nitrogen removal
PublicationThe electrochemical oxidative treatment of landfill leachates (LLs) containing high amounts of ammonia nitrogen and organic matter was used as a promising method, prior to biological processes, to achieve the final effluent quality that would be acceptable by current regulations. The deposited boron-doped diamond electrodes (BDDs) with different boron doping concentrations (10000, 5000 and 500 ppm of B) were applied as anodes....
-
Investigation of behaviour of metal structures with polymer dampers under dynamic loads
PublicationA large number of accidents concerning structures subjected to dynamic loads have been recently observed. One of the examples of such a structure is a temporary steel grandstand erected using scaffolding system. Dynamic load that is generated by crowd movement has a significant influence on the behaviour of the structure and may lead to excessive structural vibrations. The aim of the study is to consider the idea of using polymer...
-
Imidazoacridinone antitumor agent C-1311 as a selective mechanism- based inactivator of human cytochrome P450 1A2 and 3A4 isoenzymes.
Publication5-Diethylaminoethylamino-8-hydroxyimidazoacridinone (C-1311), a promising antitumor agent that is also active against autoimmune diseases, was determined to be a selective inhibitor of the cytochrome P450 (CYP) 1A2 and 3A4 isoenzymes. Therefore, C-1311 might modulate the effectiveness of other drugs used in multidrug therapy. The present work aimed to identify the mechanism of the observed C-1311-mediated inactivation of CYP1A2...
-
Application of Web-GIS for Dissemination and 3D Visualization of Large-Volume LiDAR Data
PublicationThe increasing number of digital data sources, which allow for semi-automatic collection and storage of information regarding various aspects of life has recently granted a considerable rise in popularity to the term “Big data”. As far as geospatial data is concerned, one of the major sources of Big data are Light Detection And Ranging (LiDAR) scanners, which produce high resolution three-dimensional data on a local scale. The...
-
How to Design Affect-aware Educational Systems – the AFFINT Process Approach
PublicationComputer systems, that support learning processes, can adapt to the needs and states of a learner. The adaptation might directly address the knowledge deficits and most tutoring systems apply an adaptable learning path of that kind. Apart from a preliminary knowledge state, there are more factors, that influence education effectiveness and among those there are fluctuating emotional states. The tutoring systems may recognize or...
-
Biopolyols obtained via crude glycerol-based liquefaction of cellulose: their structural, rheological and thermal characterization
PublicationIn this work lignocellulose biomass liquefaction was used to produce biopolyols suitable for the manufacturing of rigid polyurethane foams. In order to better evaluate the mechanism of the process, pure cellulose was applied as a raw material. The effect of time and temperature on the effectiveness of liquefaction and the parameters of resulting biopolyols were characterized. The prepared materials were analyzed in terms of their...
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublicationThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
The effect of road restraint systems on the level of road safety - Polish experience
PublicationRoadside accidents happen when a vehicle runs off the road. The majority of these accidents are very severe because leaving the road is usually followed by hitting a solid obstacle (tree, pole, support, culvert front wall, barrier). Roadsides are some of the most important issues of road safety. They have been studied for years to identify roadside hazards and the effectiveness of road safety measures such as restraint systems....
-
IMPROVING STUDENT SKILLS WITH ENGAGING IN HERITAGE PROTECTION PROJECTS. CASE STUDY OF ARCHITECTURAL INVENTORY WORKS AT WISŁOUJŚCIE FORTRESS, POLAND (2017)
PublicationToday's educational offer at universities contains a lot of theoretical and general knowledge, which becomes less understandable and less suitable for students of the new generation. Student's educational needs aimed at increasing the practical experience necessary for future professional life. Heritage conservation projects are a good opportunity to implement project-based learning methods. Such projects can be scientific and...
-
Advanced Oxidation Processes for the Treatment of Contaminants of Emerging Concern
PublicationThe application of contaminants of emerging concern (CEC) such as pharmaceuticals and personal care products (PPCPs), pesticides, plasticizers, endocrine disruptors, surfactants, flame retardants and polycyclic aromatic hydrocarbons (PAHs) became an indispensable requirement of the current era. Although the CEC are useful for wide-spectrum purposes, they can also result in undesirable effects on human health and other animals....
-
Faults and Fault Detection Methods in Electric Drives
PublicationThe chapter presents a review of faults and fault detection methods in electric drives. Typical faults are presented that arises for the induction motor, which is valued in the industry for its robust construction and cost-effective production. Moreover, a summary is presented of detectable faults in conjunction with the required physical information that allow a detection of specific faults. In order to address faults of a complete...
-
The efficiency and reliability of pollutant removal in a hybrid constructed wetland with giant miscanthus and Jerusalem artichoke in Poland
PublicationIn this paper, we analysed the pollutant removal efficiency and reliability of a vertical and horizontal flow hybrid constructed wetland (CW) planted with giant miscanthus and Jerusalem artichoke. The wastewater treatment plant, located in south-eastern Poland, treated domestic sewage at an average flow rate of 1.2m3·d−1. The tests were carried out during. 5-years of operation of the sewage treatment plant (2011–2016). During this...
-
Efficient Method for the Concentration Determination of Fmoc Groups Incorporated in the Core-Shell Materials by Fmoc–Glycine
PublicationIn this paper, we described the synthesis procedure of TiO2@SiO2 core-shell modified with 3-(aminopropyl)trimethoxysilane (APTMS). The chemical attachment of Fmoc–glycine (Fmoc–Gly–OH) at the surface of the core-shell structure was performed to determine the amount of active amino groups on the basis of the amount of Fmoc group calculation. We characterized nanostructures using various methods: transmission electron microscope...
-
Influence of several biodegradable components added to pure and nanosilver-doped PMMA bone cements on its biological and mechanical properties
PublicationAcrylic bone cements (BC) are wildly used in medicine. Despite favorable mechanical properties, processability and inject capability, BC lack bioactivity. To overcome this, we investigated the effects of selected biodegradable additives to create a partially-degradable BC and also we evaluated its combination with nanosilver (AgNp). We hypothesized that using above strategies it would be possible to obtain bioactive BC. The Cemex...
-
Green energy extraction for sustainable development: A novel MPPT technique for hybrid PV-TEG system
PublicationThe Photovoltaic (PV) module converts only a small portion of irradiance into electrical energy. Most of the solar energy is wasted as heat, resulting in a rise in PV cell temperature and a decrease in solar cell efficiency. One way to harvest this freely available solar thermal energy and improve PV cell efficiency is by integrating PV systems with thermoelectric generators (TEG). This cogeneration approach of the hybrid PV-TEG...
-
Electrochemical oxidation of landfill leachate using boron-doped diamond anodes: pollution degradation rate, energy efficiency and toxicity assessment
PublicationElectrochemical oxidation (EO), due to high efficiency and small carbon footprint, is regarded as an attractive option for on-site treatment of highly contaminated wastewater. This work shows the effectiveness of EO using three boron-doped diamond electrodes (BDDs) in sustainable management of landfill leachate (LL). The effect of the applied current density (25–100 mA cm−2) and boron doping concentration (B/C ratio: 500 ppm, 10,000...