Filters
total: 2596
filtered: 1245
displaying 1000 best results Help
Search results for: indect
-
Synthesis Attempt and Structural Studies of Novel A2CeWO6 Double Perovskites (A2+ = Ba, Ca) in and outside of Ambient Conditions
PublicationSynthesis Attempt and Structural Studies of Novel A 2 CeWO 6 Double Perovskites (A 2+ = Ba, Ca) in and outside of Ambient Conditions Damian Wlodarczyk,* Mikolaj Amilusik, Katarzyna M. Kosyl, Maciej Chrunik, Krystyna Lawniczak-Jablonska, Michal Strankowski, Marcin Zajac, Volodymyr Tsiumra, Aneta Grochot, Anna Reszka, Andrzej Suchocki, Tomasz Giela, Przemyslaw Iwanowski, Michal Bockowski, and Hanka Przybylinska Cite This: ACS Omega...
-
Effect of Flow Normalization in Micro-Pin-Finned Heat Sink: Numerical Study
PublicationThe micro-pin-fin heat sink (MPFHS) is widely employed for the heat transfer enhancement of microchannel heat sinks. In the current paper, the effect of flow normalization on the thermohydraulic performance of micro-pin-finned heat sinks is studied numerically. Two geometries of MPFHSs, the conventional design micro-pin-fin heat sink (CD-MPFHS) with a uniform-width micro pin fin and the proposed design micro-pin-fin heat sink (PD-MPFHS)...
-
Magnetic switching of Kerker scattering in spherical microresonators
PublicationMagneto-optical materials have become a key tool in functional nanophotonics, mainly due to their ability to offer active tuning between two different operational states in subwavelength structures. In the long-wavelength limit, such states may be considered as the directional forward- and back-scattering operations, due to the interplay between magnetic and electric dipolar modes, which act as equivalent Huygens sources. In this...
-
Application of the Chimney Cap as a Method of Improving the Effectiveness of Natural Ventilation in Buildings
PublicationAdequately designed natural ventilation is the cheapest and easiest way to effectively remove indoor pollutants and keep the air inside a building fresh. A prediction of the performance and effectiveness of ventilation in order to determine the design of a ventilation system can provide real and long-term cost savings. The worst time in terms of the efficiency of natural ventilation is the spring-autumn transition period [7]. In...
-
WYDATKI INWESTYCYJNE WOJEWÓDZTW SAMORZĄDOWYCH PO WPROWADZENIU INDYWIDUALNEGO WSKAŹNIKA ZADŁUŻENIA
PublicationOkreślenie dopuszczalnego poziomu zadłużenia jest ważną kwestią dla każdej jednostki samorządu terytorialnego w Polsce, a jej ranga jeszcze rośnie, jeśli samorząd odczuwa silną presję na dbanie o rozwój obszaru, na którym funkcjonuje, borykając się równocześnie z niedostatkiem dochodów. Taka sytuacja dotyczy większości województw samorządowych, które spośród wszystkich szczebli struktury samorządowej...
-
Zasady efektuacji w działaniach początkujących przedsiębiorców
PublicationArtykuł dotyczy efektuacyjnego, dynamicznego modelu przedsiębiorczości stanowiącego odpowiedź na wymagania zmiennego, niepewnego otoczenia biznesowego, w którym funkcjonują współcześni przedsiębiorcy. We wcześniejszych badaniach, obejmujących stosowanie pięciu zasad efektuacji w prowadzeniu firm, różni autorzy odnosili się głównie do dojrzałych przedsiębiorców, charakteryzujących się doświadczeniem w zakładaniu i prowadzeniu własnego...
-
Sprawiedliwość agrarna
Publicationprawiedliwość agrarna została napisana z intencją zreformowania stosunków społeczno-politycznych. Tekst opiera się na założeniu wywodzącym się z tradycji prawnonaturalnej, które brzmi, iż pierwotnie każdy był współwłaścicielem powierzchni Ziemi. Powstanie prywatnej własności ziemskiej (czyli, eo ipso, wywłaszczenie większości ludzi) należy zakwalifikować jako akt bezprawia, kumulujący się w historycznie nawarstwionych nierównościach...
-
Assessing Highway Travel Time Reliability using Probe Vehicle Data
PublicationProbe vehicle data (also known as “floating car data”) can be used to analyze travel time reliability of an existing road corridor in order to determine where, when, and how often traffic congestion occurs at particular road segments. The aim of the study is to find the best reliability performance measures for assessing congestion frequency and severity based on probe data. Pilot surveys conducted on A2 motorway in Poland confirm...
-
Performance Characteristics of a Micro-turbine, International
Publication. In the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:- heat...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublicationPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Curing epoxy with ethylenediaminetetraacetic acid (EDTA) surface-functionalized Co Fe3-O4 magnetic nanoparticles
PublicationIn this work, the bulk and surface composition of Fe3O4 supermagnetic nanoparticles were modified for efficient epoxy curing. The bare, ethylenediaminetetraacetic acid (EDTA) capped, and cobalt (Co)-doped EDTA capped Fe3O4 nanoparticles were synthesized electrochemically. The crystalline structure and phase information, surface capping, morphology and magnetization behavior of nanoparticles were studied by X-Ray diffraction (XRD),...
-
Investigation on Mode I Fracture Behavior of Hybrid Fiber-Reinforced Geopolymer Composites
PublicationRecent reports in the literature have shown that fber-reinforced geopolymer composites (FRGC) made with monofbers exhibit a signifcant enhancement in fracture energy. However, many aspects of the fracture performance of hybrid fberreinforced geopolymer composites (HFRGC) remain largely unexploited, and these are predominant for the structures. For the frst time, the mode I fracture energy of HFRGC is investigated. The mode I behavior...
-
Bio polyetherurethane composites with high content of natural ingredients: hydroxylated soybean oil based polyol, bio glycol and microcrystalline cellulose
PublicationIn our study, we focused on obtaining bio-polyurethane composites using bio-components such as bio glycol, modified natural oil-based polyol, and microcrystalline cellulose (MCC). The pre-polymer method was used to prepare the bio polyurethane matrix. Prepolymer was synthesized using 4,4’-diphenylmethane diisocyanate (MDI) and a polyol mixture containing 50 wt.% of commercial polyether and 50 wt.% of hydroxylated soybean oil (H3)....
-
Performance Characteristics of a Micro-Turbine
PublicationIn the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:heat output:...
-
Urban scene semantic segmentation using the U-Net model
PublicationVision-based semantic segmentation of complex urban street scenes is a very important function during autonomous driving (AD), which will become an important technology in industrialized countries in the near future. Today, advanced driver assistance systems (ADAS) improve traffic safety thanks to the application of solutions that enable detecting objects, recognising road signs, segmenting the road, etc. The basis for these functionalities...
-
Impact of influent wastewater quality on nitrogen removal rates in multistage treatment wetlands
PublicationNitrogen removal in treatment wetlands is influenced by many factors, and the presence of electron donors (biodegradable organic matter) and electron acceptors (nitrate ions) is the main limiting one; for obtaining these conditions, multistage treatment wetlands (MTWs) are required, where an extensive nitrification can be obtained in the first stages under aerobic conditions leaving then to the following anoxic/anaerobic stages...
-
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublicationThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublicationIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
Semantic URL Analytics to Support Efficient Annotation of Large Scale Web Archives
PublicationLong-term Web archives comprise Web documents gathered over longer time periods and can easily reach hundreds of terabytes in size. Semantic annotations such as named entities can facilitate intelligent access to the Web archive data. However, the annotation of the entire archive content on this scale is often infeasible. The most efficient way to access the documents within Web archives is provided through their URLs, which are...
-
Digital Gaps and Economic Inequalities in MENA Countries: An Empirical Investigation
PublicationThis research contributes to the present state of the art by examining changes in cross-country inequalities in digital technologies deployment and economic performance. Our empirical target builds on the hypothesis that rapid global diffusion of digital technologies unequivocally leads to gradual eradication of cross-country digital gaps and cross-country inequalities in terms of deployment of ICT; the technology convergence occurs....
-
Numerical investigation on distribution characteristics of oxidation air in a lime slurry desulfurization system with rotary jet agitators
PublicationRotary jet agitator is an effective device for mixing, dispersing, dissolving, and suspending dispersed phases in liquid, and is particularly advantageous to the homogenization of oxygen-enriched air within the lime slurry desulfurization system. The distribution of oxygen-enriched air in agitators is vital for the process of gypsum crystallization and the homogeneous and sufficient oxygen-enriched air can promote the formation...
-
Market Structure and Market Power in Selected Sectors of The Polish Economy Based on COICOP Classification
PublicationThis paper present new and simple measures of market structure and market power. Based on the classical models of market structures, where a given structure is determined by the number of enterprises, indexes of degree of monopoly have been estimated, representing an average number of entities per branch. Additionally, market power indexes have been determined as an average revenue per an enterprise in a given branch. This approach...
-
Development of Gas Sensor Array for Methane Reforming Process Monitoring
PublicationThe article presents a new method of monitoring and assessing the course of the dry methane reforming process with the use of a gas sensor array. Nine commercially available TGS chemical gas sensors were used to construct the array (seven metal oxide sensors and two electrochemical ones). Principal Component Regression (PCR) was used as a calibration method. The developed PCR models were used to determine the quantitative parameters...
-
Green TPUs from Prepolymer Mixtures Designed by Controlling the Chemical Structure of Flexible Segments
PublicationThis study concerns green thermoplastic polyurethanes (TPU) obtained by controlling the chemical structure of flexible segments. Two types of bio-based polyether polyols—poly(trimethylene glycol)s—with average molecular weights ca. 1000 and 2700 Da were used (PO3G1000 and PO3G2700, respectively). TPUs were prepared via a two-step method. Hard segments consisted of 4,4?- diphenylmethane diisocyanates and the bio-based 1,4-butanodiol...
-
Tensile validation tests with failure criteria comparison for various GFRP laminates
PublicationThe paper studies the mechanical properties of glass fibre reinforced polymers (GFRP) with various types and orientation of reinforcement. Analyzed specimens manufactured in the infusion process are made of polymer vinyl ester resin reinforced with glass fibres. Several samples were examined containing different plies and various fibres orientation [0, 90] or [+45, –45]. To assess the mechanical parameters of laminates, a series...
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublicationThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Optical fiber aptasensor for label-free bacteria detection in small volumes
PublicationHighly sensitive devices for fast bacteria detection are sought to be developed with the task of quantifying the worldwide problem of pathogenic bacteria and thus helping to take control over spreading bacterial infections. This work concerns a sensing solution based on microcavity in-line Mach-Zehnder interferometer (μIMZI) induced in an optical fiber. Such a device exhibits ultrahigh sensitivity to refractive index changes...
-
Zarządzanie terminowością w projektach. Wskaźniki i narzędzia
PublicationCzas jest istotnym elementem tzw. trójkąta projektu, dlatego też terminowość, rozu-miana, jako realizacja przedsięwzięcia w zadanym czasie, to parametr, który powinien podle-gać szczególnemu nadzorowi, a ryzyko nieterminowej realizacji powinno być wykrywane niezwłocznie. Istniejące już metody, takie jak np. wartość wypracowana (j.ang Earned Value - EV) pozwalają zaadresować te wyzwania, jednak ze względu na swoją złożoność mogą...
-
Wieloobszarowa rozmyta regulacja PID mocy reaktora jądrowego
PublicationW artykule przedstawiono wieloobszarowy regulator rozmyty z lokalnymi regulatorami PID dla sterowania mocą reaktora jądrowego typu PWR. Wykorzystano model matematyczny o parametrach skupionych reaktora PWR obejmujący procesy generacji i wymiany ciepła oraz efektów reaktywnościowych. Nastawy lokalnych regulatorów PID zostały dobrane w sposób optymalny, minimalizując całkowy wskaźnik jakości ISE. Na przykładzie pokazano że zastosowane...
-
Computationally efficient two-objective optimization of compact microwave couplers through corrected domain patching
PublicationFinding an acceptable compromise between various objectives is a necessity in the design of contemporary microwave components and circuits. A primary reason is that most objectives are at least partially conflicting. For compact microwave structures, the design trade-offs are normally related to the circuit size and its electrical performance. In order to obtain comprehensive information about the best possible trade-offs, multi-objective...
-
Assessment of Failure Occurrence Rate for Concrete Machine Foundations Used in Gas and Oil Industry by Machine Learning
PublicationConcrete machine foundations are structures that transfer loads from machines in operation to the ground. The design of such foundations requires a careful analysis of the static and dynamic effects caused by machine exploitation. There are also other substantial differences between ordinary concrete foundations and machine foundations, of which the main one is that machine foundations are separated from the building structure....
-
The Technological Advancement of New Products, Product Newness and Market Information
PublicationThe purpose of this study is to propose product newness and obtaining market information as mediators of the relationship between the technological advancement of a new product and its commercial success. So far, little is known about the mediators of this relationship but knowledge about the factors that strengthen or weaken it is valid, both for the theory and practice of new product management. On the one hand, product newness...
-
Museum Institutions in Monuments - Positive and Negative Aspects of Adaptation: The New Amber Museum and Museum of Science in Gdansk, Poland
PublicationThe issue of the creation and location of new museums is a current topic. The decision of where and how to create new museum facilities will impact successful function in the future. Museums are either located in newly designed buildings or in existing buildings. In general, existing buildings adapted for museum use are either formally under conservational protection or not. With regard to museum location in preserved monuments,...
-
Arctic catchment as a sensitive indicator of the environmental changes: distribution and migration of metals (Svalbard)
PublicationArctic regions experience metal pollution, despite their remote location, and the distribution and migration of those metals determine their potential impact on the local environment. Here, a High-Arctic catchment (Revelva, Svalbard) located remotely from human-induced pollution sources is studied with respect to the distribution and migration of chosen trace elements (Ag, Al, As, B, Ba, Bi, Ca, Cd, Co, Cr, Cu, Cs, Mo, Ni, Pb,...
-
Interactive and Media Architecture – From Social Encounters to City Planning Strategies
PublicationThe paper searches into the potential of media and interactive projects to support participation and generate social encounters in public spaces. Moreover, it proposes implementation of media and interactive projects into city planning processes. On the basis of theoretical approaches, case studies and interdisciplinary surveys the paper gives insight how interactive and media architecture can engage people in activities in urban...
-
The Influence of Articular Cartilage Thickness Reduction on Meniscus Biomechanics
PublicationObjective Evaluation of the biomechanical interaction between meniscus and cartilage in medial compartment knee osteoarthritis. Methods The finite element method was used to simulate knee joint contact mechanics. Three knee models were created on the basis of knee geometry from the Open Knee project. We reduced the thickness of medial cartilages in the intact knee model by approximately 50% to obtain a medial knee osteoarthritis...
-
Imunofan - RDKVYR peptide - stimulates skin cell proliferation and promotes tissue repair
PublicationRegeneration and wound healing are vital to tissue homeostasis and organism survival. One of the biggest challenges of today's science and medicine is finding methods and factors to stimulate these processes in the human body. Effective solutions to promote regenerative responses will accelerate advances in tissue engineering, regenerative medicine, transplantology, and a number of other clinical...
-
An Analysis of Contextual Aspects of Conceptualization: A Case Study and Prospects
PublicationIn this chapter we present a new approach to development of modularized knowledge bases. We argue that modularization should start from the very beginning of modeling, i.e. from the conceptualization stage. To make this feasible, we propose to exploit a context-oriented, semantic approach to modularization. This approach is based on the Structural Interpretation Model (SIM) presented earlier elsewhere. In the first part of thischapter...
-
Positive management of the university
PublicationAbstract: The prevailing view held at contemporary Polish universities is that their main goal is to achieve effects measured by indicators, which applies to each element of their mission: education, research and the third mission, whereas the means to accomplish this goal consists of increasing the requirements and motivating by the “carrot and stick” approach. That approach discounts the importance of building a positive relationship...
-
PVA-Based Films with Strontium Titanate Nanoparticles Dedicated to Wound Dressing Application
PublicationBioactive materials may be applied in tissue regeneration, and an example of such materials are wound dressings, which are used to accelerate skin healing, especially after trauma. Here, we proposed a novel dressing enriched by a bioactive component. The aim of our study was to prepare and characterize poly(vinyl alcohol) films modified with strontium titanate nanoparticles. The physicochemical properties of films were studied,...
-
How do responsible universities perceive their social engagement? In search of signs of Creating Shared Value by the University
PublicationObjectives: University social responsibility still lacks legitimisation and is perceived as a burden that hinders academics from doing research and teaching. Creating Shared Value by the University may serve as a tool to motivate universities to engage in initiatives for society, as this is beneficial for both parties. Yet, some researchers perceive the creation of economic value as inappropriate for academia. Thus, it was interesting...
-
Human Resource Management Digitalisation in Multidisciplinary Ship Design Companies
PublicationThe digitalisation in the ship design sector is currently applied to the design process itself and is well defined, partially standardised and practically implemented by both independent design companies and the design departments of shipyards. The situation is similar in other sectors of engineering. However, the requirements for the digitalisation of other processes in design and engineering companies have not previously been...
-
The impact of global value chains on wages, employment, and productivity: a survey of theoretical approaches
PublicationThis study presents a systematic literature review to provide a collection of theories explaining the impact of global value chains (GVCs) on labour market outcomes. Due to the complex nature of GVCs and the interconnectedness of wages, employment, and productivity, many direct and indirect effects are at play. To ensure a transparent and systematic flow of the review process, I follow the PRISMA guide. Eventually, 36 records out...
-
GIS-based hydrodynamic modeling for urban flood mitigation in fast-growing regions: a case study of Erbil, Kurdistan Region of Iraq
PublicationFloods threaten urban infrastructure, especially in residential neighborhoods and fast-growing regions. Flood hydrodynamic modeling helps identify flood-prone locations and improve mitigation plans' resilience. Urban floods pose special issues due to changing land cover and a lack of raw data. Using a GIS-based modeling interface, input files for the hydrodynamic model were developed. The physical basin's properties were identified...
-
Engineering boron and nitrogen codoped carbon nanoarchitectures to tailor molecularly imprinted polymers for PFOS determination
PublicationPer- and polyfluoroalkyl substances (PFAS) have gained significant attention as emerging contaminants due to their persistence, abundance, and adverse health effects. Consequently, the urgent need for ubiquitous and effective sensors capable of detecting and quantifying PFAS in complex environmental samples has become a priority. In this study, we present the development of an ultrasensitive molecularly imprinted polymer (MIP)...
-
Intermolecular Interactions as a Measure of Dapsone Solubility in Neat Solvents and Binary Solvent Mixtures
PublicationDapsone is an effective antibacterial drug used to treat a variety of conditions. However, the aqueous solubility of this drug is limited, as is its permeability. This study expands the available solubility data pool for dapsone by measuring its solubility in several pure organic solvents: N-methyl-2-pyrrolidone (CAS: 872-50-4), dimethyl sulfoxide (CAS: 67-68-5), 4-formylmorpholine (CAS: 4394-85-8), tetraethylene pentamine (CAS:...
-
Combined numerical and experimental approach to determine numerical model of abdominal scaffold
PublicationA proper junction of the prosthesis and the abdominal wall is important in successful hernia repair. The number of tacks should be balanced to assure appropriate mesh fixation and not to induce post-operative pain. Numerical simulations help to find this balance. The study is aimed at creating a proper numerical model of a knitted surgical mesh subjected to boundary conditions and load occurring in the abdominal cavity. Continuous,...
-
Antiproliferative, Antiangiogenic, and Antimetastatic Therapy Response by Mangiferin in a Syngeneic Immunocompetent Colorectal Cancer Mouse Model Involves Changes in Mitochondrial Energy Metabolism
PublicationIn spite of the current advances and achievements in cancer treatments, colorectal cancer (CRC) persists as one of the most prevalent and deadly tumor types in both men and women worldwide. Drug resistance, adverse side effects and high rate of angiogenesis, metastasis and tumor relapse remain one of the greatest challenges in long-term management of CRC and urges need for new leads of anticancer drugs. We demonstrate that CRC...
-
Validation of Hydraulic Mechanism during Blowout Trauma of Human Orbit Depending on the Method of Load Application
PublicationThe more we know about mechanisms of the human orbital blowout type of trauma, the better we will be able to prevent them in the future. As long as the buckling mechanism’s veracity is not in doubt, the hydraulic mechanism is not based on equally strong premises. To investigate the correctness of the hydraulic mechanism’s theory, two different methods of implementation of the hydraulic load to the finite element method (FEM) model...
-
PLA–Potato Thermoplastic Starch Filament as a Sustainable Alternative to the Conventional PLA Filament: Processing, Characterization, and FFF 3D Printing
PublicationThe growing popularity of the fused filament fabrication (FFF) 3D printing technology in science, industry, and in-home use is associated with an increased demand for high-quality polymer filaments. This study presents an in-depth characterization and analysis of a self-made bio-based polylactide (PLA)/thermoplastic potato starch (TPS) filament dedicated for the FFF 3D printing technology. The obtained results were compared with...