displaying 1000 best results Help
Search results for: THE EQUIVALENCE PRINCIPLE
-
Water uptake in protective organic coatings and its reflection in measured coating impedance
PublicationWater uptake in commercially available epoxy coating on mild steel using impedance spectroscopy and gravimetry was studied. The water content in the coating was determined using the Brasher-Kingsbury equation and various methods of coating capacitance calculation used in the literature. The obtained results were compared with reference gravimetric data. An overestimation of values obtained from impedance data in relation to gravimetric...
-
Optimising approach to designing kernel PCA model for diagnosis purposes with and without a priori known data reflecting faulty states
PublicationFault detection plays an important role in advanced control of complex dynamic systems since precise information about system condition enables efficient control. Data driven methods of fault detection give the chance to monitor the plant state purely based on gathered measurements. However, they especially nonlinear, still suffer from a lack of efficient and effective learning methods. In this paper we propose the two stages learning...
-
Efficiency of gas detection algorithms using fluctuation enhanced sensing
PublicationEfficiency of various gas detection algorithms by applying fluctuation enhanced sensing method was discussed. We have analyzed resistance noise observed in resistive WO3- nanowires gas sensing layers. Power spectral densities of the recorded noise were used as the input data vectors for two algorithms: the principal component analysis (PCA) and the support vector machine (SVM). The data were used to determine gas concentration...
-
Kernel PCA in Application to Leakage Detection in Drinking Water Distribution System
PublicationMonitoring plays an important role in advanced control of complex dynamic systems. Precise information about system's behaviour, including faults detection, enables efficient control. Proposed method- Kernel Principal Component Analysis (KPCA), a representative of machine learning, skilfully takes full advantage of the well known PCA method and extends its application to nonlinear case. The paper explains the general idea of KPCA...
-
Gdańsk Urban Initiative Laboratory
PublicationGdansk is Poland's principal seaport, situated on the southern edge of the Gdansk Bay on the Baltic Sea. The city is the capital and largest city of the Pomeranian Voivodeship. Gdansk, in a conurbation with the city of Gdynia and the resort town of Sopot, and suburban communities, jointly forms Poland's fourth largest metropolitan area, with a population approaching 1.4 million. The pathways towards the Micro ULL FWE Nexus Square...
-
Analytical studies of spectrum broadcast structures in quantum Brownian motion
PublicationSpectrum broadcast structures are a new and fresh concept in the quantum-to-classical transition, introduced recently in the context of decoherence and the appearance of objective features in quantum mechanics. These are specific quantum state structures, responsible for the objectivization of the decohered state of a system. Recently, they have been demonstrated by means of the well-known quantum Brownian motion model of the recoilless...
-
Chemometrics approaches to green analytical chemistry procedure development
PublicationChemometric tools are widely used in analytical chemistry for the reduction of data dimensionality, grouping of variables and processing of analytical signals. They have also the potential to be applied in analytical procedure development with the aim of minimizing the procedure’s environmental impact. The design of experiment gives the possibility to obtain much better information on the system response than in case of “changing...
-
Krzysztof Nyka dr hab. inż.
PeopleKrzysztof Nyka, received MSc (1986) PhD (2002) and DSc (2020) degrees in telecommunication and electrical engineering from the Faculty of Electronics, Telecommunications and Informatics (ETI) of Gdańsk University of Technology (GUT), Poland. He is currently an Associate Professor at the Department of Microwaves and Antenna Engineering, Faculty of ETI, GUT. Before his academic career, he worked for the electronic industry (1984-1986). Research...
-
NOWE ŻYCIE DWORCÓW KOLEJOWYCH - MOŻLIWOŚCI MODERNIZACJI OBIEKTÓW OBSŁUGI PASAŻERÓW
PublicationW aspekcie współcześnie zachodzących zmian demograficznych, rozwijających się technologii oraz poszukiwania rozwiązań proekologicznych wzrasta potencjał transportu kolejowego. Po okresie upadku znaczenia kolei jesteśmy świadkami jej postępującej transformacji w Europie. Do obsługi ruchu pasażerskiego służy w Polsce prawie 600 dworców kolejowych, z których większość nie jest jeszcze przystosowana do aktualnych potrzeb użytkownika...
-
Dotacje unijne jako źródło finansowania innowacji w małych i średnich przedsiębiorstwach
PublicationArtykuł dotyczy wskazania możliwości pozyskania źródeł finansowania innowacji małych i średnich przedsiębiorstw. Przykładem tego mają być dostępne obecnie lub w przyszłości granty i fundusze unijne. W artykule przedstawiono owe dotacje i ogólne ich zasady z uwzględnieniem programu z jakiego pochodzą i dla jakiego podmiotu mają być dedykowane. Ponadto zaprezentowano propozycje na co mogą być przeznaczone środki z poszczególnych...
-
Stereo image visualization for a VISROBOT system
PublicationThe article describes a novel approach to robotic vision in mobile robot systems. The system implements a Visrobot system which implements a generic idea of using mobile robots for exploring an indoor environment. The task of such a robot is to visualize a stereo image properly for an operator. The system uses different stereo baseline values. Variable baseline can result in increasing depth resolution for distant objects. We assume...
-
An Approach to Bass Enhancement in Portable Computers Employing Smart Virtual Bass Synthesis Algorithms
PublicationThe aim of this paper is to present a novel approach to the Virtual Bass Synthesis (VBS) algorithms applied to portable computers. The developed algorithms are related to intelligent, rule-based setting of synthesis parameters according to music genre of an audio excerpt and to the type of a portable device in use. To find optimum synthesis parameters of the VBS algorithms, subjective listening tests based on a parametric procedure...
-
LCT, PIV and IR Imaging Detection in Selected Technical and Biomedical Applications
PublicationThermochromic liquid crystals (TLC), Particle Image Velocimetry (PIV) and Infrared Imaging Themography (IR) have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. These four tools (based on the desktop computers) have come together during the past two decades to produce a powerful advanced experimental technique as a judgment of quality of information that cannot be obtained...
-
Liquid Crystals, PIV and IR-Photography in Selected Technical and Biomedical Applications
PublicationThermochromic liquid crystals (TLC), Particle Image Velocimetry (PIV), Infrared Imaging Themography (IR) and True-Colour Digital Image Processing (TDIP) have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. These four tools (based on the desktop computers) have come together during the past two decades to produce a powerful advanced...
-
Effect of electron count and chemical complexity in the Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor
PublicationHigh-entropy alloys are made from random mixtures of principal elements on simple lattices, stabilized by a high mixing entropy. The recently discovered body-centered cubic (BCC) Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor appears to display properties of both simple crystalline intermetallics and amorphous materials; e.g., it has a well-defined superconducting transition along with an exceptional robustness against disorder....
-
Autonomous Driver Based on an Intelligent System of Decision-Making
PublicationThe paper presents and discusses a system (xDriver) which uses an Intelligent System of Decision-making (ISD) for the task of car driving. The principal subject is the implementation, simulation and testing of the ISD system described earlier in our publications for the task of autonomous driving. The design of the whole ISD system is a result of a thorough modelling of human psychology based on an extensive literature study. Concepts...
-
Determination of API content in a pilot-scale blending by near-infrared spectroscopy as a first step method to process line implementation
PublicationNear infrared (NIR) spectroscopy was used for estimation of powder blend homogeneity and manufacturing control of a medicinal product powder mixture containing active pharmaceutical ingredient (API). Aiming at initiating a Process Analytical Technology (PAT) activity, the first step was a stationary mode atline evaluation. In this, the content of pharmaceutical active compound in the powder mixtures intended to the direct tabletting...
-
Analiza PCA sekwencji aktywnej termografii dynamicznej w diagnostyce oparzeń
PublicationCelem niniejszej pracy jest analiza metod przetwarzania obrazów opartych na analizie składowychgłównych oraz analizie składowych niezależnych, które pozwola na uzyskanie nowych informacji obadanym obiekcie. W ramach pracy powstało oprogramowanie, które pozwala na analizezarejestrowanych sekwencji termograficznych metoda składowych głównych - Principal ComponentAnalysis - PCA. Została przeprowadzona weryfikacja działania powyższych...
-
Analysis of thoracic regional impedance changes using PCA approach
PublicationA multichannel impedance and one lead electrocardiographic recording system has been developed. The impedance measurement unit is built using a four-electrode technique. It consists of a sinusoidal, 40 kHz, current source and five measurement channels. Circumferential current electrodes have been located at a neck and an abdomen. Voltagemeasurement disk electrodes formed five two-electrode measurement ports. The impedance change...
-
Kazimierz Market Place. Akwarela 38x56cm
PublicationL'acquerello in Alessandria, la mostra internazionale patrocinata dal Comune e dalle Provincia di Alessandria, dalla Regione Piemonte e dal Comune di Vignale e organizzata dall'Associazione italiana acquerellisti. L'esposizione, circa 150 acquerelli dei socie Aia e di artisti provenienti da Australia, Belgio, Brasile Polonia e Spagna per presentare le principali tecniche dell'acquerelli e le diverse concezioni artistiche e stilistiche...
-
DIRECTIONS OF THE SCIENTIFIC RESEARCH CONDUCTED IN THE DEPARTMENT OF MARINE AND POWER PLANTS OF THE FACULTY OF OCEAN ENGINEERING AND SHIP TECHNOLOGY OF THE GDANSK UNIVERSITY OF TECHNOLOGY
PublicationIn this article the short historical outline of the Department of Marine and Land Power Plants of the Faculty of Ocean Engineering and Ship Technology of the Gdansk University of Technology was introduced. Its activity beginnings, in the post-war history of the University, reach 1952. The leading scientific issues, which have been developed for years in three principal directions: design, manufacture and operation of machines and...
-
Numerical assessment of ultimate strength of severe corroded stiffened plates
PublicationThe objective of this work is to investigate numerically (using the non-linear FEM and the approach stipulated by the Common Structural Rules) the severe nonuniform corrosion degradation effect on the ultimate strength of stiffened plates and compare the results to the already published experimental works. Different factors governing structural behavior of corroded stiffened plates are investigated, such as corrosion degradation level,...
-
Chemical modifications of natural oils and examples of their usage for polyurethane synthesis
PublicationNatural oils have been used in the production of plastics for a long time. However, the number of studies dedicated to polyurethane research has shown an increase only recently. Usually, petrochemical components are used in polyurethane synthesis. Nowadays, there have been attemptsmade to replace polyols in polyurethanes with the modified oils and other natural raw materials. It is a promising and important scenario because the...
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublicationThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
2-D constitutive equations for orthotropic Cosserat type laminated shells in finite element analysis
PublicationWe propose 2-D Cosserat type orthotropic constitutive equations for laminated shells for the purpose of initial failure estimation in a laminate layer. We use nonlinear 6-parameter shell theory with asymmetric membrane strain measures and Cosserat kinematics as the framework. This theory is specially dedicated to the analysis of irregular shells, inter alia, with orthogonal intersections, since it takes into account the drilling...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Loudness Scaling Test Based on Categorical Perception
PublicationThe main goal of this research study is focused on creating a method for loudness scaling based on categorical perception. Its main features, such as: way of testing, calibration procedure for securing reliable results, employing natural test stimuli, etc., are described in the paper and assessed against a procedure that uses 1/2-octave bands of noise (LGOB) for the loudness growth estimation. The Mann-Whitney U-test is employed...
-
Polynomial analysis as a new way of describing dynamic impedance spectra – Differential and relative impedance spectra
PublicationModel measurements of an equivalent electrical system were carried out using the technique of Dynamic Electrochemical Impedance Spectroscopy. The measurement took the form of potentiodynamic changes imposed on the tested system. Using the possibility of continuous impedance measurements, an attempt was made to develop an original and innovative method of analyzing impedance spectrograms, which is termed polynomial analysis. As...
-
Modelling and simulations in time-fractional electrodynamics based on control engineering methods
PublicationIn this paper, control engineering methods are presented with regard to modelling and simulations of signal propagation in time-fractional (TF) electrodynamics. That is, signal propagation is simulated in electromagnetic media described by Maxwell’s equations with fractional-order constitutive relations in the time domain. We demonstrate that such equations in TF electrodynamics can be considered as a continuous-time system of...
-
Portable Raman spectrometer - design rules and applications
PublicationRaman spectroscopy has become more popular due to its new prospective field applications in forensic sciences, war against terrorism, environment protection and other field chemical analysis. Raman spectrometers can be miniaturised to portable devices and their price is decreasing due to development of optoelectronics components. Unfortunately, this technology has still numerous limitations that influence their design and limit...
-
Low-cost EM-Simulation-based Multi-objective Design Optimization of Miniaturized Microwave Structures
PublicationIn this work, a simple yet reliable technique for fast multi-objective design optimization of miniaturized microwave structures is discussed. The proposed methodology is based on point-by-point identification of a Pareto-optimal set of designs representing the best possible trade-offs between conflicting objectives such as electrical performance parameters as well as the size of the structure of interest. For the sake of computational...
-
Necessary and Sufficient Condition for State-Independent Contextual Measurement Scenarios
PublicationThe problem of identifying measurement scenarios capable of revealing state-independent contextuality in a given Hilbert space dimension is considered. We begin by showing that for any given dimension d and any measurement scenario consisting of projective measurements, (i) the measure of contextuality of a quantum state is entirely determined by its spectrum, so that pure and maximally mixed states represent the two extremes...
-
Tensile failure study of 3D printed PLA using DIC technique and FEM analysis
PublicationThe paper presents the experimental and numerical study of the failure behaviour of Fused Filament Fabricated (FFF) Polylactic Acid (PLA) samples subjected to tensile load. The examined samples are printed in flat orientation with 0◦, 45◦ and 90◦ raster angles. During the experiments the deformation of the specimens is continuously scanned with the 3D Aramis measuring system utilizing the digital imaging correlation technique,...
-
Inverse surrogate models for fast geometry scaling of miniaturized dual-band couplers
PublicationRe-design of microwave structures for various sets of performance specifications is a challenging task, particularly for compact components where considerable electromagnetic (EM) cross-couplings make the relationships between geometry parameters and the structure responses complex. Here, we address geometry scaling of miniaturized dual-band couplers by means of inverse surrogate modeling. Our approach allows for fast estimation...
-
Dissociative multi-photon ionization of isolated uracil and uracil-adenine complexes
PublicationRecent multi-photon ionization (MPI) experiments on uracil revealed a fragment ion at m/z 84 that was proposed as a potential marker for ring opening in the electronically excited neutral molecule. The present MPI measurements on deuterated uracil identify the fragment as C3H4N2O+ (uracil+ less CO), a plausible dissociative ionization product from the theoretically predicted open-ring isomer. Equivalent measurements on thymine...
-
Rapid multi-objective design optimisation of compact microwave couplers by means of physics-based surrogates
PublicationThe authors introduce a methodology for fast multi-objective design optimisation of miniaturised microwave couplers. The approach exploits the surrogate-based optimisation paradigm with an underlying low-fidelity model constructed from an equivalent circuit of the structure under consideration, corrected through implicit and frequency space mapping. A fast prediction tool obtained this way is subsequently optimised by a multi-objective...
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublicationThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
A Direct Modulation for Matrix Converters based on the Onecycle Atomic operation developed in Verilog HDL.
PublicationThis paper presents a fast direct Pulse Width Modulation (PWM) algorithm for the Conventional Matrix Converters (CMC) developed in Verilog Hardware Description language (HDL). All PWM duty cycle calculations are performed in one cycle by an atomic operation designed as a digital module using FPGA basic blocks. The algorithm can be extended to any number of output phase. The improved version of the discontinuous Direct Analytic...
-
Polynomial description of dynamic impedance spectrogram—introduction to a new impedance analysis method
PublicationThis paper presents a polynomial description of spectrograms obtained using Dynamic Electrochemical Impedance Spectroscopy. A method to fit the polynomial degree correctly is discussed. A simple electrical system of a diode connected in parallel with a capacitor was used for testing. Dynamic impedance measurements during potentiodynamic polarization were conducted. This paper presents an alternative analysis method that allows...
-
Comparative Study of Integer and Non-Integer Order Models of Synchronous Generator
PublicationThis article presents a comparison between integer and non-integer order modelling of a synchronous generator, in the frequency domain as well as in the time domain. The classical integer order model was compared to one containing half -order systems. The half-order systems are represented in a Park d-q axis equivalent circuit as impedances modelled by half-order transmittances. Using a direct method based on the approximation...
-
On Applications of Elements Modelled by Fractional Derivatives in Circuit Theory
PublicationIn this paper, concepts of fractional-order (FO) derivatives are reviewed and discussed with regard to element models applied in the circuit theory. The properties of FO derivatives required for the circuit-level modeling are formulated. Potential problems related to the generalization of transmission-line equations with the use of FO derivatives are presented. It is demonstrated that some formulations of FO derivatives have limited...
-
Energy neutrality versus carbon footprint minimization in municipal wastewater treatment plants
PublicationThis work aimed to compare the carbon footprint (CF) of six full-scale wastewater treatment plants (WWTPs). The CF was estimated in the range of 23–100 kg CO2e per population equivalent. In the total CF, the direct emissions held the highest share (62–74%) for the plants with energy recovery from biogas. In the plants depending entirely on the power grid, the indirect emissions due to energy consumption dominated the total CF (69–72%)....
-
Magdalena Szuflita-Żurawska
PeopleHead of the Scientific and Technical Information Services at the Gdansk University of Technology Library and the Leader of the Open Science Competence Center. She is also a Plenipotentiary of the Rector of the Gdańsk University of Technology for open science. She is a PhD Candidate. Her main areas of research and interests include research productivity, motivation, management of HEs, Open Access, Open Research Data, information...
-
Recent advances in hydrogen production from biomass waste with a focus on pyrolysis and gasification
PublicationThis paper presents the results research on the optimal fuel compositions and the control parameters of the spark ignition engine fueled with syngas-biogas-hydrogen for the purpose of setting up a flexible electronic control unit for the engine working in a solar-biomass hybrid renewable energy system. In syngas-biogas-hydrogen mixture, the optimal content of hydrogen and biogas is 20% and 30%, respectively. Exceeding these thresholds,...
-
Flexible syngas-biogas-hydrogen fueling spark-ignition engine behaviors with optimized fuel compositions and control parameters
PublicationThis paper presents the results research on the optimal fuel compositions and the control parameters of the spark ignition engine fueled with syngas-biogas-hydrogen for the purpose of setting up a flexible electronic control unit for the engine working in a solar-biomass hybrid renewable energy system. In syngas-biogas-hydrogen mixture, the optimal content of hydrogen and biogas is 20% and 30%, respectively. Exceeding these thresholds,...
-
Carsharing - Opportunities and Threats for Cities: Proposals of Solutions for Urban Policy
PublicationThe carsharing of a current generation is a short-term car renting service with a capability to find in the nearest surrounding a fleet car parked anywhere in the public space where the previous user left it, as well as to book, open, rent and pay of, with the use of a dedicated mobile application. Nowadays, only a minority of municipalities is considering implementing the carsharing in their policies. The lack of awareness of...
-
Reprezentation of mechanic hysteresis in a railway track using the Preisach model
PublicationThis paper presents an implementation of the classic scalar Preisach model to describe the hysteresis phenomenon created in a railway track subjected to lateral (in the horizontal plane) displacements. The principles of the Preisach theory and the scalar mathematical model of the mechanical hysteresis that is based on statistically distributed modified hysteresis operators are briefly presented. This article presents the characteristic...
-
Validating data acquired with experimental multimodal biometric system installed in bank branches
PublicationAn experimental system was engineered and implemented in 100 copies inside a real banking environment comprising: dynamic handwritten signature verification, face recognition, bank client voice recognition and hand vein distribution verification. The main purpose of the presented research was to analyze questionnaire responses reflecting user opinions on: comfort, ergonomics, intuitiveness and other aspects of the biometric enrollment...
-
Analytical methodologies for determination of artificial sweeteners in foodstuffs- a review
PublicationArtificial high-intensity sweeteners are more and more frequently used for food production. Food industry tends to highlight beneficial aspects of their use, such as tooth-friendliness, rising-up quality of life of those suffering from different forms of diabetes and possibility of weight control without sacrificing favorite unhealthy drinks or snacks. On the other hand some of the consumers are deeply concerned about safety of...
-
Innovative Bidirectional Isolated High-Power Density On-Board Charge for Vehicle-to-Grid
PublicationThis paper deals with developing and implementing a bidirectional galvanically isolated on-board charger of a high-power density. The power density of the new charger was 4 kW/kg and 2.46 kW/dm3, and the maximum efficiency was 96.4% at 3.4 kW. Due to the requirement to achieve a high-power density, a single-stage inverter topology was used. Regarding switching losses, due to the topology of the circuit with so-called hard switching,...