Filtry
wszystkich: 1616
wybranych: 1294
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SHIPPING NOISE
-
Multibeam data processing for 3D object shape reconstruction
PublikacjaThe technology of hydroacoustic scanning offers an efficient and widely-used source of geospatial information regarding underwater environments, providing measurement data which usually have the structure of irregular groups of points known as point clouds. Since this data model has known disadvantages, a different form of representation based on representing surfaces with simple geometric structures, such as edges and facets,...
-
Planning, Configuration and Usefulness of Microseismic Monitoring on Eastern-Europe Platform – Example from East Pomerania
PublikacjaThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing process. The method uses array of geophones to localize micro tremors induced by liquid pumped underground at high rate and pressure. The acquired information helps to optimize fracturing process and prevents fracture growth to aquifer levels. It proved to be useful on several unconventional hydrocarbon reservoirs in the USA....
-
Design of poroelastic wearing course with the use of direct shear test
PublikacjaPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Przyrząd wirtualny do wykrywania szumów wybuchowych w przyrządach półprzewodnikowych metodą obrazowania szumów
PublikacjaW artykule scharakteryzowano właściwości szumów wybuchowych (RTS) w dziedzinie czasu i częstotliwości oraz omówiono stosowane metody identyfikacji szumów RTS. Przedstawiono konstrukcję systemu, do szybkiej identyfikacji szumów wybuchowych, zbudowanego w oparciu o metodę Noise Scattering Pattern (NSP). System składa się z głowicy pomiarowej, zawierającej spolaryzowany badany przyrząd półprzewodnikowy, filtru dolnoprzepustowego,...
-
Gdansk Bay sea bed sounding and classification of its results
PublikacjaThe main goal of this paper is to describe the results of sounding the Gdansk Bay sea bed by using a SES-2000 Standard parametric sub-bottom profiler. Quality of data obtained during trials depends inter alia on a proper location of transducer array to reduce influence of pitch, roll and heave motions as well as ship self noise (resulting from bubbles due to propeller and flow around hull, vibration generated by main engine and...
-
Reduction of Tire Rolling Resistance by Optimization of Road Surfaces and Tires
PublikacjaDuring interaction between tire and road surface three very important phenomena are always in effect. One of them (very desirable) is friction that is important for traction, braking and cornering. Two other phenomena are not desirable at all, that is rolling resistance and noise. This paper discusses relations between road surface and tire parameters versus tire rolling resistance. Road surface texture, porosity, impedance, strength...
-
Single-Slope ADC With Embedded Convolution Filter for Global-Shutter CMOS Image Sensors
PublikacjaThis brief presents an analog-to-digital converter (ADC) suitable for acquisition and processing of images in the global-shutter mode at the pixel level. The ADC consists of an analog comparator, a multi-directional shift register for the comparator states, and a 16-bit reversible binary counter with programmable step size. It works in the traditional single-slope mode. The novelty is that during each step of the reference ramp,...
-
Tinnitus Therapy Based on High-Frequency Linearization Principles - Preliminary Results
PublikacjaThe aim of this work is to present problems related to tinnitus symptoms, its pathogenesis, hypotheses on tinnitus causes, and therapy treatment to reduce or mask the phantom noise. In addition, the hypothesis on the existence of parasitic quantization that accompanies hearing loss has been recalled. Moreover, the paper describes a study carried out by the Authors with the application of high-frequency dither having specially formed...
-
Multi-task Video Enhancement for Dental Interventions
PublikacjaA microcamera firmly attached to a dental handpiece allows dentists to continuously monitor the progress of conservative dental procedures. Video enhancement in video-assisted dental interventions alleviates low-light, noise, blur, and camera handshakes that collectively degrade visual comfort. To this end, we introduce a novel deep network for multi-task video enhancement that enables macro-visualization of dental scenes. In particular,...
-
New approach to urban housing - Report of ISOCARP Young Planning Professionals Workshop, Gdynia School of Urbanizm, Aesop Urban Summer School
PublikacjaThe workshop was organized along with the INTERNATIONAL CONFERENCE LIVING IN THE CITY – PROBLEMS AND CHALLENGES OF SHAPING HOUSING POLICY which is hosted by the City of Gdynia Poland. It was conducted in frame of Young Planning Professionals Program and 7th AESOP uropean Urban Summer School but also as the new type of the activity for the Young Planners “Gdynia School of...
-
The Creation of an Antimicrobial Coating on Contact Lenses by The Use of Nanocopper
PublikacjaThe aim of the research was to creation an antimicrobial coating on contact lens and examine the ability of copper nanoparticles to decrease microbial adhesion and prevent the growth of bacteria. The creation was based on the immersion method in solution with dispersed nanoparticles of copper at concentration 200 pm. There were evaluated follows factors: time of immersion and base to dispersed nanoparticles. Three solutions: ethyl...
-
Discrimination of workers aged 55+ in companies in Poland
PublikacjaThe problem of discrimination on the grounds of age in the workplace is particularly topical not only in Poland but also in Europe as a whole. The paper presents the essence of the discrimination and its most common manifestations. The results of own research on the youngPoles' perception of the discrimination on grounds of age in the workplace, intergenerational competition in the labour market and some of the factors shaping...
-
MIEJSKIE PROJEKTY OŚWIETLENIOWE W KONTEKŚCIE REWITALIZACJI
PublikacjaUrban Lighting in the Context of Regeneration Processes. The article presents how multi-layered urban lighting projects fi t into the programs of integrated activities to improve the living conditions of the local community, the surrounding space, and its economic relations. The role of the electric lighting in revealing the night image of the city, its promotion and public spaces transformations off ering new impressions to city...
-
Contemporary architecture within the context of architectural education
PublikacjaAnalysed in this article are the diploma projects of students of architecture in European countries. The aim was to examine how students approach an important issue related to sustainable development, i.e. the integration of newly designed architecture into the existing historical, cultural and natural context. The rational use and protection of the environment requires the skilful shaping of urbanised space. Many changes in the...
-
Differentiation Between Spirits According to Their Botanical Origin
PublikacjaAgricultural distillates are used for the production of spirit beverages. As more and more products with a specific botanical composition specified on the label are produced (e.g. rye vodkas, wheat vodkas and Polish Vodka, which cannot be produced with the addition of maize distillate), it is necessary to look for quicker and more accurate methods allowing the determination of botanical origin of alcoholic beverages and materials...
-
Design Methodology for Small Passenger Ships On the Example of the Ferryboat Motława 2 Driven by Hybrid Propulsion System
PublikacjaDynamic development in practically all elds of science and engineering has not passed over shipbuilding . In last years , engineers got to their use computer soware which makes it possible to perform strength and hydrodynamic calculations as well as to visualize design projects in 3 D space [1-4]. At their disposal they have full spectrum of modern solutions associated with the use of advanced materials and technologies [5-7]....
-
Minimizing Greenhouse Gas Emissions From Ships Using a Pareto Multi-Objective Optimization Approach
PublikacjaTo confront climate change, decarbonization strategies must change the global economy. According to statements made as part of the European Green Deal, maritime transport should also become drastically less polluting. As a result, the price of transport must reflect the impact it has on the environment and on health. In such a framework, the purpose of this paper is to suggest a novel method for minimizing emissions...
-
Preliminary experimental research on stability of truss' joint with positive eccentricity
PublikacjaRecently, a very large interest in lightweight steel structures made from cold-formed sections has been noticeable. In the design practice, a large emphasis is put on rational shaping of both the thin-walled elements and constructions designed on them. The aim of this paper is to present the methodology for preparation of experimental research that model the behaviour of members in trusses made of cold-formed sections with positive...
-
THE INFLUENCE OF THE EVOLUTION OF DAYLIGHTING SYSTEMS OF EXHIBITION SPACE ON THE ARCHITECTURE OF THE MUSEUM'S BUILDING
PublikacjaThe paper deals with the architecture of museums as dependent on the ways of lighting the exhibition space. The work focuses on the analysis of the influence of daylighting systems on shaping the museum's architecture in the period from the Renaissance to modern times. The method of work includes studying literature and the case study of the objects characteristic of the presented concepts and lighting systems. The results of the...
-
Design of Resilient Vehicle-to-Infrastructure Systems
PublikacjaVehicular ad hoc networks (VANETs) have recently gained noticeable attention due to advantages in improving road traffic safety, shaping the road traffic and providing infotainment opportunities to travellers. However, transmission characteristics following from the IEEE 802.11p standard and the high mobility of VANET nodes remarkably reduce the lifetime, reach and capacity of wireless links, and often lead to simultaneous disruptions...
-
The Impact of Building Performance Analysis on intuition Development and Decision Making Rationality
PublikacjaContemporary architectural workshop is characterized by the ability to efficiently collect and process huge amounts of geometric and non-geometric information. Virtual substitutes for buildings and structures allow to analyze various aspects of real life activity at various stages of the design process. The possibility of increased prognostic quantitative data acquisition, such as cost of energy consumption, shifts architectural...
-
Dopants and gas modifiers in ion mobility spectrometry
PublikacjaThe ion mobility techniques, including the most commonly used drift-tube ion mobility spectrometry (IMS) and differential mobility spectrometry (DMS), are used successfully for the detection of a wide range of organic compounds in the gas phase. In order to improve detection quality, admixtures are added to gas streams flowing through the detector. Dopants mostly prevent the ionization of interfering chemicals however, better detection...
-
Compensation of pressure peaks in pwk-type hydraulic pumps
Publikacjahydraulic axial pumps equipped with cam-driven commutation unit (pwk pumps) proved their high efficiency up to 55 mpa and ability to work self-sucking, even at high speed. displacement of pwk pump may easily be changed by moving its control cam. full discharge from hydrostatic forces makes such control possible by direct action of a low-energy actuator like proportional electromagnet or stepping motor. that eliminates heavy and...
-
Enzymatic activities behind degradation of glucosinolates
PublikacjaMyrosinase (thioglucosidase, EC 3.2.1.147) is the enzyme responsible for the hydrolysis of glucosinolates (GLs). In plant tissue, myrosinase and GLs are sequestered in separate cellular compartments. As a result of cell disruption, e.g., after pathogen attack or on chopping or grinding during food preparation, the myrosinase comes into contact with GLs and catalyzes the hydrolysis of thioglucosidic bond in GL structure. Consequently,...
-
Dynamic charging of electric buses
PublikacjaDespite the continuous development of electrochemical battery technology and the multitude of electric buses on offer, it is still not possible to exploit electric buses in urban transport on an all-day basis without the necessity of charging them. It is therefore necessary to build point-to-point contact charging stations or induction charging stations at the terminals. This results in substantial financial outlays connected with...
-
Navigational decision support system during approach manoeuvre in emergency STS transfer operation
PublikacjaThe paper is concerned with the problem of safe trajectory planning for approaching during emergency STS (Ship to Ship) transfer operation with oil spill. The safe trajectory means that the way points does not cross in the area of the environment with the static and dynamic obstacles and at the same time satisfies ship's stopping and speed deceleration performance. The evolutionary path planning algorithm is used to determine trajectory...
-
Low cost electrochemical sensor module for measurement of gas concentration
PublikacjaThis paper describes a low cost electrochemical sensor module for gas concentration measurement. A module is universal and can be used for many types of electrochemical gas sensors. Device is based on AVR ATmega8 microcontroller. As signal processing circuit a specialized integrated circuit LMP9l000 is used. The proposed equipment will be used as a component of electronic nose system employed for classifying and distinguishing...
-
Chemiresistive gas sensors based on carbon nanotubes - fabrication and application
PublikacjaMany types of sensors have been invented to identify and quantify chemical contamination in the gas phase. Sensors based on carbon nanotubes are particularly attractive because of their wide range of applicaions and potential use in electronic nose that can be controlled using algorithms of Artificial Intelligence. Sensor functions, fabrication and selected applications are reviewed and discussed with focus on chemiresistors. Drawbacks...
-
Merging extremum seeking and self-optimizing narrowband interference canceller - overdetermined case
PublikacjaActive cancellation systems rely on destructive interference to achieve rejection of unwanted disturbances entering the system of interest. Typical practical applications of this method employ a simple single input, single output arrangement. However, when a spatial wavefield (e.g. acoustic noise or vibration) needs to be controlled, multichannel active cancellation systems arise naturally. Among these, the so-called overdetermined...
-
Methods for quality improvement of multibeam and LiDAR point cloud data in the context of 3D surface reconstruction
PublikacjaPoint cloud dataset is the transitional data model used in several marine and land remote-sensing applications. During further steps of processing, the transformation of point cloud spatial data to more complex models containing higher order geometric structures like edges and facets may be possible, if an appropriate quality level of input data is provided. Point cloud datasets usually contain a considerable amount of undesirable...
-
A Mesh Deformation Technique Based on Solid Mechanics for Parametric Analysis of High-Frequency Devices With 3-D FEM
PublikacjaIn this paper, a versatile technique for mesh defor- mation is discussed, targeted at the electromagnetic (EM) field simulation of high-frequency devices using the 3-D finite element method (FEM). The approach proposed applies a linear elasticity model to compute the displacements of the internal mesh nodes in 3-D when the structure geometry is changed. The technique is compared with an alternative approach...
-
Automatic Detection of Nerves in Confocal Corneal Images with Orientation-Based Edge Merging
PublikacjaThe paper presents an algorithm for improving results of automatic nerve detections in confocal microscopy images of human corneal. The method is designed as a postprocessing step of regular detection. After the nerves are initially detected, the algorithms attempts to improve the results by filling unde-sired gaps between single nerves detections in order to correctly mark the entire nerve instead of only parts of it. This approach...
-
Programmable Input Mode Instrumentation Amplifier Using Multiple Output Current Conveyors
PublikacjaIn this paper a programmable input mode instrumentation amplifier (IA) utilising second generation, multiple output current conveyors and transmission gates is presented. Its main advantage is the ability to choose a voltage or current mode of inputs by setting the voltage of two configuration nodes. The presented IA is prepared as an integrated circuit block to be used alone or as a sub-block in a microcontroller or in a field...
-
Algorithms of chemicals detection using raman spectra
PublikacjaRaman spectrometers are devices which enable fast and non-contact identification of examined chemicals. These devices utilize the Raman phenomenon to identify unknown and often illicit chemicals (e.g. drugs, explosives)without the necessity of their preparation. Now, Raman devices can be portable and therefore can be more widely used to improve security at public places. Unfortunately, Raman spectra measurements is a challenge...
-
Organic Vapor Sensing Mechanisms by Large-Area Graphene Back-Gated Field-Effect Transistors under UV Irradiation
PublikacjaThe gas sensing properties of graphene back-gated field-effect transistor (GFET) sensors toward acetonitrile, tetrahydrofuran, and chloroform vapors were investigated with the focus on unfolding possible gas detection mechanisms. The FET configuration of the sensor device enabled gate voltage tuning for enhanced measurements of changes in DC electrical characteristics. Electrical measurements were combined with a fluctuation-enhanced...
-
Optimisation and field assessment of poroelastic wearing course bond quality
PublikacjaCompared to typical asphalt mixtures, poroelastic mixtures are characterised by high porosity and high flexibility, which are desirable for traffic noise reduction. However, the same properties increase the risk of debonding from the lower layer, which is a significant source of premature damage. The study investigates which of the factors – tack coat agent, type and texture of the lower layer – have the greatest impact on interlayer...
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublikacjaTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
Roughness evaluation of turned composite surfaces by analysis of the shape of Autocorrelation Function
PublikacjaIn this paper, the application of an Autocorrelation Function for the characterisation of surface topography was validated. The roughness evaluation of turned composite surfaces was supported by sophisticated studies of the Autocorrelation Function properties, considering especially the shape of the function. Details were measured with the optical method. The selection of the surface roughness evaluation procedures was carried...
-
Topography measurement methods evaluation for entire bending-fatigued fracture surfaces of specimens obtained by explosive welding
PublikacjaIn this paper, the methods of compensation of differences in the results of entire bending-fatigued fracture surface topographies were presented. The roughness evaluation was performed with a focus variation microscope and confocal surface topography measurement techniques. The differences in the ISO 25178 roughness parameters were investigated and procedures for their compensation were studied. It was found that various types...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Adaptation of Architectural Heritage in the Era of Climate Change. Torpedo Platform in Babie Doły
PublikacjaThe paper provides original insight into the problem of adap¬tation of historical objects in the era of climate change. It conveys a message that in times of climate crisis, there is a need to go beyond an anthropocentric perspective, specifically, that architec¬ture should not only be designed for people, but should also provide a framework for nature. As well as shaping spaces for human beings, the architect is also responsible...
-
A sense of security and freedom in a residential environment
PublikacjaThe article is based on the results of a survey carried out among students of architecture faculties in several countries, which examined the students’ knowledge of shaping the housing environment in such a way as to enable them to fulfil two basic and, at the same time, seemingly mutually exclusive psychological needs of a person: a sense of security and a sense of freedom. In examining these issues, particular emphasis was placed...
-
Mixed ionic-electronic conductivity and structural properties of strontium-borate glass containing nanocrystallites of Bi2 VO5.5
PublikacjaSamples of strontium borate glass containing bismuth vanadate nanocrystallites were prepared. Nanocomposites containing up to 45mol% of the Bi2VO5.5 phase exhibit electrical properties closer to the strontium-borate glass than to the ferroelectric Bi2VO5.5 ceramic. The glass matrix still may contain some part of bismuth and vanadium ions even after crystallization process and there is too little of crystalline phase to observe...
-
Optimum shape of turnout diverging track with segments of variable curvature
PublikacjaIn the paper an attempt has been made to focus on shaping the variable curvature in the diverging track of the railway turnout. Basing on some earlier studies, solutions provided with a circular arc in the mid-zone, and in the extreme regions with segments of non-linear curvature of equal length and zero curvature at the start and end of the turnout, have been assumed as models. The most advantageous type of curvature has been...
-
Energy efficient beam control for 5G antennas
PublikacjaThe rapid development of 5G and beyond systems demands improvement in communication speed, latency and safety to maintain the required quality of service. This paper presents an overview of different concepts of energy-efficient antenna systems, which offer beam-shaping and beam-steering functionalities, that enhance connectivity performance and can be used in 5G applications. Different designs for 5.9 GHz, 39 GHz and 60 GHz frequency...
-
MARKETING STRATEGY - SPACE AS A PRODUCT.ARCHITECTURE AS A MARKETING DEVICE.
PublikacjaSpace has its measurable financial value. From the economic point of view place can be treated as a product that fights for appearing in tourists' and investors' consciousnesses. Space - treated as the object of demand and supply - becomes an element in a marketing game. To reach its maximal value the given space should be competitive to other spaces, from which it wants to stand out. However, in the field of architecture - and...
-
On the independence number of some strong products of cycle-powers
PublikacjaIn the paper we give some theoretical and computational results on the third strong power of cycle-powers, for example, we have found the independence numbers alpha((C^2_10)^⊠3) = 30 and alpha((C^4 _14)^⊠3) = 14. A number of optimizations have been introduced to improve the running time of our exhaustive algorithm used to establish the independence number of the third strong power of cycle-powers. Moreover, our results establish...
-
Maxillary sinus aeration analysis using computational fluid dynamics
PublikacjaThe maxillary sinus aeration using the computational fluid dynamics (CFD) method based on individual adult patients’ computed tomography (CT) scans were analyzed. The analysis was based on CT images of 4 patients: one with normal nose anatomy and three with nasal septal deviation (NSD) and concha bullosa (CB). The CFD simulation was performed using the Reynolds-Average Simulation approach and turbulence closure based on linear...
-
Sklepy typu pop-up – od Guerilla Stores marki Comme de Garcons przez unikalne doświadczenie zakupowe Bikini Berlin do ... ?
PublikacjaObiekty, sklepy typu pop- up pojawiały się w miastach ponad dziesięć lat temu. Otwierane są na krótki okres czasu w celu promocji marki i nawiązania bezp o- średniego kontaktu z odbiorcą. Pop -up’y różnią się od tradycyjnych, stacjona r- nych sklepów rodzajem prowadzonej w nich działalności, mającym na celu przede wszystkim promocję marki. Pierwsze tymczasowe obiekty, tzw. Guerilla stores , stworzone zostały w 2004 roku...
-
Nowoczesne układy przekształtników wielopoziomowych do zasilania statków z lądu
PublikacjaW artykule poruszono tematykę zasilania statków zacumowanych w porcie z lądowej sieci elektroenergetycznej poprzez wykorzystanie nowoczesnych konstrukcji przekształtników energoelektronicznych. W treści pracy zaprezentowano porównanie dwóch topologii wysokonapięciowych przekształtników wielopoziomowych. Porównano konstrukcje przekształtników z klasycznym transformatorem wielouzwojeniowym oraz z transformatorami wysokoczęstotliwościowymi.