Publikacje
Filtry
wszystkich: 511
Katalog Publikacji
Rok 2019
-
Properties of LiMnBO3 glasses and nanostructured glass-ceramics
PublikacjaPolycrystalline LiMnBO3 is a promising cathode material for Li-ion batteries. In this work, we investigated the thermal, structural and electrical properties of glassy and nanocrystallized materials having the same chemical composition. The original glass was obtained via a standard melt-quenching method. SEM and 7Li solid-state NMR indicate that it contains a mixture of two distinct glassy phases. The results suggest that the...
-
The Impact of Crushed Rock Spoil on Pitting Corrosion of Selected Stainless Steel
PublikacjaThe paper presents the results of the pitting resistance investigations of selected stainless steels in the chloride environment and the simultaneous impact of erosive factors using the cyclic polarization technique. Additionally, using electrochemical techniques, ie: electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential, the behavior of the passive layer of selected stainless steels in the environment...
-
The influence of dynamic load changes on temporary impedance in hydrogen fuel cells, selection and validation of the electrical equivalent circuit
PublikacjaTo achieve optimal performance of a fuel cell, a reliable monitoring and diagnostic method is required. The currently utilized methods give limited information or they are impossible to use under dynamic working conditions. To obtain comprehensive information about the fuel cell operation we utilized novel dynamic electrochemical impedance spectroscopy. Impedance measurements in dynamic mode were performed on a hydrogen fuel cell,...
-
The Influence of Microstructure on the Passive Layer Chemistry and Corrosion Resistance for Some Titanium-Based Alloys
PublikacjaThe effect of microstructure and chemistry on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys, was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys...
-
The optimization of enzyme immobilization at Au-Ti nanotextured platform and its impact onto the response towards glucose in neutral media
PublikacjaThe market of non-invasive glucose sensors is drastically growing due to increasing number of people suffering from diabetes. Therefore, there is a significant need for any improvement in the field of biosensors that can be used for monitoring glucose level in human body. In recent years the emphasis is put onto the modification of electrode material with enzymes possessing recognition centre specific towards particular molecules....
-
The Production Possibility of the Antimicrobial Filaments by Co-Extrusion of the PLA Pellet with Chitosan Powder for FDM 3D Printing Technology
PublikacjaThe last decades have witnessed a major advancement and development in three-dimensional (3D) printing technology. In the future, the trend’s utilization of 3D printing is expected to play an important role in the biomedical field. This work presents co-extrusion of the polylactic acid (PLA), its derivatives (sPLA), and chitosan with the aim of achieving filaments for printing 3D objects, such as biomedical tools or implants. The...
-
Tuning of the Electrochemical Properties of Transparent Fluorine-doped Tin Oxide Electrodes by Microwave Pulsed-plasma Polymerized Allylamine
PublikacjaWe report here the dry, one-step, and low-temperature modification of FTO surfaces using pulsed plasma polymerization of allylamine (PPAAm). PPAAm/FTO surfaces were characterized by X-ray photoelectron spectroscopy, spectroscopic ellipsometry, and contact angles to understand the morphological, structural, and optical properties. FTO were coated with a very thin layer of adherent cross-linked, pinhole-, and additive-free allylamine...
-
Understanding the origin of high corrosion inhibition efficiency of bee products towards aluminium alloys in alkaline environments
PublikacjaVarious bee products were found to be efficient corrosion inhibitors of aluminium in different environments. In particular, bee pollen was found to be highly effective in alkaline electrolytes, yet its highly complex composition and possible synergistic interactions hinder determination of the compounds acting as active corrosion inhibitors. The main purpose of the following work is to investigate the effect of solvents used for...
Rok 2015
-
Protection of bridges against stray current corrosion
PublikacjaA case study of Siennicki Bridge stray current corrosion hazard is presented. A corrosion risk was caused by incorrectly designed tram line traction which goes over the bridge. No dielectric insulation between running rails and bridge steel construction was used. A variety of protection methods against stray currents are described. Characteristics of the endangered bridge were described. Impressed current cathodic protection system...
-
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublikacjaRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
The protection and monitoring of a distribution piping network for potable water supply
PublikacjaPurpose – The purpose of this paper is to implement the corrosion protection method for steel pipes used in a municipal water-pipe network. Results of an inhibitor protection system installed on the system are presented. Inhibitor protection was required due to the high corrosivity of the water collected by a surface intake, which had resulted in a large number of failures and low water quality, due to the presence of corrosion...
-
Thin layer of ordered boron-doped TiO2 nanotubes fabricated in a novel type of electrolyte and characterized by remarkably improved photoactivity
PublikacjaThis paper reports a novel method of boron doped titania nanotube arrays preparation by electrochemical anodization in electrolyte containing boron precursor – boron trifluoride diethyl etherate (BF3 C4H10O), simultaneously acting as an anodizing agent. A pure, ordered TiO2 nanotubes array, as a reference sample, was also prepared in solution containing a standard etching compound: ammonium fluoride. The doped and pure titania...
-
Weryfikacja dokumentacji technicznej systemu ochrony katodowej rurociągu paliwowego
PublikacjaZweryfikowano dokumentację techniczną systemu ochrony katodowej rurociągu paliwowego
Rok 2020
-
Protective and Suppressing Electromagnetic Interference Properties of Epoxy Coatings Containing Nano-Sized NiZn Ferrites
PublikacjaNano-crystalline ferrites with the chemical formula NixZn(1−x)Fe2O4, where x = 0, 0.2, 0.4, 0.6, 0.8, 1.0, were synthesized using a co-precipitation method. The obtained ferrites were investigated by X-ray diffraction (XRD). The corrosion inhibiting behavior of nano-sized ferrites was tested using carbon steel samples and 10% aqueous ferrite extracts. Results were compared with previous data obtained for micro-sized ceramic ferrites....
-
Pseudo-superparamagnetic behaviour of bariumhexaferrite particles
PublikacjaThe effect of hexadecyltrimethylammonium bromide (CTAB) addition on the crystal structure, morphology,and magnetic properties of co-precipitated hexagonal barium ferrite was investigated. For afixed amount ofsurfactant, different Fe3+concentrations and Fe3+/Ba2+ratios were used to optimize the formation ofsingle-phase barium ferrite particles. The results indicated that the obtained ferrite particles exhibitedcoercivity changes...
-
RESEARCH ON ORGANIC COATINGS DESIGNED FOR UNDERWATER APPLICATIONS
PublikacjaUnderwater steel structures require periodic maintenance. In the case of vessels, anti-corrosion works are carried out in the shipyard, where very good conditions for applying organic protective coatings can be provided. Very good surface preparation can be obtained by the use of abrasive blasting. The well-prepared metal surface is free from impurities (particularly inorganic salts). Suitable conditions for the application and...
-
Scalable Route toward Superior Photoresponse of UV-Laser-Treated TiO2 Nanotubes
PublikacjaTitanium dioxide nanotubes gain considerable attention as a photoactive material due to chemical stability, photocorrosion resistance, or lowcost manufacturing method. This work presents scalable pulsed laser modification of TiO2 nanotubes resulting in enhanced photoactivity in a system equipped with a motorized table, which allows for modifications of both precisely selected and any-large sample area. Images obtained from scanning...
-
Simultaneous voltammetric determination of Cd2+, Pb2+, and Cu2+ ions captured by Fe3O4@SiO2 core-shell nanostructures of various outer amino chain length
PublikacjaIn the present study, we examined a novel functionalised magnetic nanoparticles Fe3O4@SiO2-Nn as a nano adsorbent for binding of Cd2+, Pb2+, Cu2+ ions in an aqueous solution. First, we obtained the nanoparticles functionalised with various carbon chains containing different number of amino groups: (3-amino)propyltriethoxysilane (Fe3O4@SiO2-N1), N-(2-aminoethyl)-3-aminopropyltrimethoxysilane (Fe3O4@SiO2-N2) and N1-(3-trimethoxysilylpropyl)diethylenetriamine...
-
Single-step grown boron doped nanocrystalline diamond-carbon nanograss hybrid as an efficient supercapacitor electrode
PublikacjaDirect synthesis of nano-structured carbon hybrid consisting of vertically aligned carbon nanograss on top of boron-doped nanocrystalline diamond is demonstrated and the carbon hybrid is further applied as an electrode material for the fabrication of supercapacitor. The hybrid film combines the dual advantages of sp2 (carbon nanograss) and sp3 (nanocrystalline diamond) bonded carbon, possessing not only the excellent electrical...
-
Special Issue: Recent Advances in Corrosion Science
PublikacjaThe dynamic development of the global industry and growing demand for new material technologies generates constantly increasing problems regarding premature material degradation and the requirement to determine corrosion mechanisms and to develop new protection/evaluation approaches. This Special Issue, “Recent Advances in Corrosion Science”, brings together fourteen articles and one review, providing a snapshot of the recent activity...
-
Stratification of nano-pigments in anti-corrosive coatings by means of magnetic field
PublikacjaThe concept of self-stratification of coatings, although attractive, causes difficulties in its practical use, especially when pigments are added to the resins. An alternative way of obtaining a multilayer structure in a single step was presented. Using the inhomogeneous magnetic field and magnetically active components of the coating, the possibility of vertically graded differentiation of the one layer properties has been verified....
-
Surface and Corrosion Properties of AA6063-T5 Aluminium Alloy in Molybdate-containing Sodium Chloride Solutions
PublikacjaCorrosion properties of aluminium alloy AA6063-T5 were investigated in molybdate-containing NaCl solutions. Electrochemical, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. SEM-EDX, magnetic force, and intermodulation electrostatic force microscopy data suggested that the inhibition initiation preferentially occurred over Fe-rich cathodic IMPs. Spectroscopic...
-
Synthesis, thermal, structural and electrical properties of vanadium-doped lithium-manganese-borate glass and nanocomposites
PublikacjaA glassy sample with a nominal formula LiMn1−3x/2VxBO3 (where x = 0.05) was synthesised using the melt-quenching method. Material was characterised by differential thermal analysis (DTA), X-ray diffactometry (XRD) at room temperature and as a function of temperature (HT-XRD), X-ray photoelectron spectroscopy (XPS), impedance spectroscopy (IS) and scanning electron microscopy (SEM). Dependences of glass transition and crystallisation...
-
The electrochemical determination of isatin at nanocrystalline boron-doped diamond electrodes: stress monitoring of animals
PublikacjaUltra-thin nanocrystalline boron-doped diamond electrodes (B:NCD) were used for the electrochemical determination of isatin in dog urine samples using cyclic voltammetry and square wave voltammetry in a phosphate buffer saline, pH = 7.2. No additional modification or pretreatment of the electrode surface was required in this approach, being of high importance for the facile detection procedure. The increase of the peak current...
-
The geometry of free-standing titania nanotubes as a critical factor controlling their optical and photoelectrochemical performance
PublikacjaTitanium dioxide nanotubes are regarded as one of the most important functional materials and due to their unique electronic properties, chemical stability and photocorrosion resistance, they find applications in, for example, highly efficient photocatalysis or perovskite solar cells. Nevertheless, modification of TiO2 nanotubes is required to overcome their main drawback, i.e. large energy bandgap (>3.2 eV) limiting their ability...
-
The impact of air humidity on the operation of proton exchange membrane fuel cells determined using dynamic electrochemical impedance spectroscopy
PublikacjaThis paper describes the changes in the fuel cell impedance across a range of current loads and humidity changes. The changes of each equivalent circuit parameters representing specific processes occurring in fuel cells, as a function of humidity and current changes, were determined. Within the combined scope of current and humidity, the optimal working conditions of the cells were determined, corresponding to the lowest impedance...
-
The impedance of hydrogen oxidation reaction in a proton exchange membrane fuel cell in the presence of carbon monoxide in hydrogen stream
PublikacjaEvaluation of performance of a proton exchange membrane fuel cell, which is affected by carbon monoxide that pollutes the hydrogen stream, was presented. This influence was studied for carbon monoxide concentration of 125–325 ppb, which are close to values specified in ISO 14687:2019 standard. Performed studies provided crucial information for further development of fuel cell as an energy source for automotive application. Impedance...
-
The influence of the Cu2O deposition method on the structure, morphology and photoresponse of the ordered TiO2NTs/Cu2O heterojunction
PublikacjaThe increased interest in highly ordered titania structures exhibiting tubular shape that could be directly formed onto the stable substrate is related with the intensive research on their modification enabling absorption of light within the wide solar spectrum and its further conversion into electric or chemical energy. Among others, formation of uniform 3D heterojunctions based on the TiO2 nanotubes attracts attention since porous...
-
The Synergistic Microbiological Effects of Industrial Produced Packaging Polyethylene Films Incorporated with Zinc Nanoparticles
PublikacjaZinc compounds in polyolefin films regulate the transmission of UV-VIS radiation, affect mechanical properties and antimicrobial activity. According to hypothesis, the use of zinc- containing masterbatches in polyethylene films (PE) with different chemical nature—hydrophilic zinc oxide (ZO) and hydrophobic zinc stearate (ZS)—can cause a synergistic effect, especially due to their antimicrobial properties. PE films obtained on an...
-
Thermally tuneable optical and electrochemical properties of Au-Cu nanomosaic formed over the host titanium dimples
PublikacjaAu-Cu nanostructures offer unique optical and catalytic properties unlike the monometallic ones resulting from the specific interaction. Among others, they have the ability to exhibit surface plasmon resonance, electrochemical activity towards the oxygen and hydrogen evolution reaction (OER, HER) as well as improved photoresponse in relation to monometalic but those properties depend highly on the substrate where bimetallic structures...
-
Ultrastructural analysis of the submandibular sialoliths: Raman spectroscopy and electron back-scatter studies
PublikacjaThe aim of work was the epidemiological analysis of the occurrence of sialolithiasis of the submandibular gland in adults and the evaluation of the ultrastructure of salivary stones. The study sample consisted of 44 sialoliths. Analysis of the structure and chemical composition of sialoliths was performed using a Scanning Electron Microscope and Raman Spectroscopy. Comparing our results with the literature we can say that the epidemiology...
Rok 2007
-
Quadratic Cohen representations in spectral analysis of serration process in Al-Mg alloys
PublikacjaIstotny z mechanicznego punktu widzenia efekt Portevina Le-Chateliera charakteryzuje się skomplikowanym profilem widmowym. Jako typowy przykład procesu niestacjonarnego, wymaga specjalnego podejścia umożliwiającego analizę zmian rozkładu energii fluktuacji naprężenia w funkcji odkształcenia. Jako narzędzie umożliwiające realizację powyższego założenia autorzy proponują zastosowanie rodziny przekształceń kwadratowych znanych jako...
-
Quadratic Cohen representations in spectral analysis of serration process in Al–Mg alloys
PublikacjaImportant from mechanical point of view the Portevin–Le Chatelier serration phenomenon is being characterized by a complicated spectral profile. As a typical example of nonstationary processes it demands a special treatment allowing to follow the evolution of energy of stress fluctuations as a function of strain. The authors suggest the utilization of a compact system of quadratic transformations, known as Cohen class, as a technique...
-
Skaningowa impedancyjna mikroskopia sił atomowych
PublikacjaW pracy przedstawiono nowatorskie podejście do analizy impedancyjnej sprzężonej z mikroskopią sił atomowych. Stosowane współcześnie metody pomiaru impedancyjnego w kontaktowym trybie AFM opierają się na punktowym pomiarze zmiennoprądowym z wykorzystaniem sekwencyjnego, sinusoidalnego pobudzania badanego obiektu. Autorzy proponują wykorzystanie techniki dynamicznej, co umożliwia uzyskiwanie widm impedancyjnych w warunkach ciągłego...
Rok 2002
-
Reliability of flue gas desulphurisation installations - the essential condition of efficient air pollution control
PublikacjaW celu minimalizacji niekorzystnego wpływu SO2 i SO3 na środowisko naturalne w wielu instalacjach skrubery odsiarczające gaz spalinowy (FGD) stosowane są do usuwania tlenków siarki z gazów wylotowych. Ostre warunki pracy skruberów i dodatkowego osprzętu powodują problemy korozyjne w powszechnie stosowanych materiałach konstrukcyjnych a awarie wywierają długookresowy wpływ na środowisko. Opisano najnowsze doświadczenia związane...
-
Teoretyczny opis metody pomiaru chwilowego widma impedancyjnego. Theoretical description of the measuring of instantenous impedance spectra
PublikacjaPrzedstawiony został teoretyczny opis wyznaczania chwilowego widma impedancyjnego. Połączenie szumu pseudo-białego oraz metody krótkoczasowej transformacji Fouriera pozwala na wyznaczenie zmian widma impedancyjnego w funkcji czasu. Teoretyczne podstawy nowej metody pomiarowej wskazują na możliwość zastosowania jej do procesów niestacjonarnych.
-
The comparative study of different methods of spectral analysis of electrochemical oscillations
PublikacjaOscylacje elektrochemiczne często połączone są z roztwarzaniem metali. One często wykazują niestacjonarny charakter. W związku z czym wydaje się konieczne wykonanie analizy w równoczesnej dziedzinie czasu i częstotliwości. Zaprezentowano porównanie trzech nowych metod: STFT, transformacji falkowej i rozkładu Wigner-Ville´a. Zalety tych metod zostały wypunktowane oraz wykazane zostały różnice pomiędzy analizą Fourierowską i technikami...
-
The effect of the temperature change rate on determination of the criticalpitting temperature of stainless steels
PublikacjaPrzedstawiono wyniki badań wpływu szybkości zmian temperatury na wyznaczaną krytyczną temperaturę korozji wżerowej. Badania stali 316L przeprowadzono metodą termometrii cyklicznej. Stwierdzono, że zwiększenie szybkości zmian temperatury związane jest ze zwiększeniem wyznaczonej temperatury krytycznej. Zależność krytycznej temperatury korozji wżerowej od szybkości korozji ma charakter liniowy. Wartości krytycznej temperatury korozji...
-
The stationarity characteristics of electrochemical current noise
PublikacjaPrzedstawiono rezultaty analizy szumu elektrochemicznego generowanego podczas korozji stali 0H18N9 w roztworze 0.1 M H2SO4+0,006 M Cl-. Rejestry uzyskano w warunkach potencjostatycznych. W szumie zaobserwowano trendy i sygnały przejściowe, charakterystyczne dla korozji wżerowej. Trend został usunięty za pomocą aproksymacji wielomianem trzeciego stopnia. Analiza statystyczna wykazała niestacjonarny bądź słabo stacjonarny charakter...
Rok 2016
-
Research on causes of corrosion in the municipal water supply system
PublikacjaThis paper presents results of failure analysis study to characterize the corrosion damage that occurred in the water supply system in Krakow. This analysis includes: electrochemical noise, linear polarization and resistometric measurements. Water aggressiveness of four water intakes was defined using Langelier and Ryznar indices. Results from this indices did not reveal the causes of considerable corrosion losses in water systems....
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublikacjaThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublikacjaThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Study on surface termination of boron-doped diamond electrodes under anodic polarization in H2SO4 by means of dynamic impedance technique
PublikacjaAnodic oxidation is a popular way to modify termination bonds at boron doped diamond electrodes altering their electrochemical and physicochemical properties. Our studies, performed with dynamic electrochemical impedance spectroscopy technique, supported with X-ray photoelectron spectroscopy and ellipsometry analysis prove its utility in continuous on-line monitoring of impedance changes on the electrode surface under polarization...
-
Synthesis and photoelectrochemical behaviour of hydrogenated titania nanotubes modified with conducting polymer infiltrated by redox active network
PublikacjaIn this work, we show preparation of ordered inorganic-organic composite electrode material where hydrogenated titania nanotubes H-TiO2 with tubularly developed surface modified with poly(3,4-ethylenedioxythiophene) matrix permeated by Prussian Blue (PB) inorganic redox network in order to reach highly photoactive heterojunction. The polymer deposition was realized via two subsequent processes covering: i) potentiostatic polymerization...
-
System pomiaru szybkości korozji metodą polaryzacji liniowej w zbiorniku zatłaczającym wodę złożową oraz systemu wody morskiej na platformie wydobywczej Baltic Beta
PublikacjaWykonano analizę sprawności systemu monitorowania szybkości korozji na Platformie wydobywczej Baltic Beta. Dokonano niezbędnych czynności, które umożliwiły ponowne uruchomienie systemu. Przedstawiono rejestry szybkości korozji w okresie od 01.01.2015 do 24.11.2016
-
Titania nanotubes infiltrated with conducting polymer PEDOT modified by Prussian Blue – a novel type of organic-inorganic heterojunction characterised with enhanced photoactivity.
PublikacjaA highly ordered p–n heterojunction was formed based on titania nanotubes containing a conducting polymer with Prussian blue matrix. The study demonstrates, for the first time, cases when a composite based on titania array scaffolding and Prussian blue embedded in PEDOT exhibits reversible FeII/FeIII redox activity. Highly enhanced photoactivity and capacitance of the obtained material are depicted in comparison to pristine titania....
-
Wyjaśnienie przyczyn pocienienia rur w piecu technologicznym PC-1 na instalacji DRW II
PublikacjaWykonano analizę przyczyn korozji rur pieca instalacji DRW w oparciu o badania wizualne, SEM, EDX oraz literaturowe. W ciągu 5 lat eksploatacji nastąpiły znaczne ubytki korozyjne rur w wyniku procesów korozyjnych. Z uwagi na zbyt wysoką temperaturę rurek pieca nastąpił proces wysokotemperaturowego pylenia metalu.
-
Wykorzystanie technik zmiennoprądowych w analizie polaryzacji katodowej stali
PublikacjaRozprawę doktorską pod tytułem „Wykorzystanie technik zmiennoprądowych w analizie polaryzacji katodowej stali” podzielono na trzy zasadnicze części, które nawiązują do zróżnicowanego charakteru tematyki korozyjnej. W pierwszym rozdziale pracy podjęto problematykę kryteriów ochrony katodowej stosowanych w dokumentach technicznych. Przedstawiono podstawy teoretyczne ochrony katodowej oraz poddano analizie obecnie stosowane normy....
Rok 2024
-
Risks caused by microbiologically influenced corrosion in diesel fuel storage tanks
PublikacjaMicrobiologically influenced corrosion (MIC) poses serious problems for the petrochemical and refinery industries. Particularly favourable conditions for MIC arise in storage tanks and transmission pipelines for mixtures of diesel oil with the addition of a biocomponent (in Poland 7%). The best conditions for the development of MIC occur at the fuel-water interface, where microorganisms are provided with a source of food and water,...
-
Validation of dynamic electrochemical impedance spectrograms using autocorrelation function
PublikacjaValidation of impedance data is essential for checking the reliability of experimental data. Kramers – Kronig transformation is used to verify data obtained from classical Electrochemical Impedance Spectroscopy (EIS) measurements. Data obtained from Dynamic Electrochemical Impedance Spectroscopy (DEIS) could be validated in the same way, but in this case, there is no information about internal consistency between every single spectrum...
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublikacjaThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
Rok 2003
-
Rozkład acetonu w roztworach wodnych z udziałem mikroorganizmów immobilizowanych na cząstkach stałych, tworzących odwróconą warstwę fluidalną.
PublikacjaBakterie A. calcoaceticus zastosowano do biodegradacji acetonu w roztworach wodnych. Bakterie immobilizowano na lekkich cząstkach stałych które tworzyły warstwę fluidalną w strefie opadania reaktora airlift z zewnętrzną cyrkulacją. Stwierdzono, że czas biodegradacji rośnie ze wzrostem wartości pH i ze wzrostem początkowego stężenia ketonu. Począwszy od pewnej wysokości warstwy fluidalnej prędkość biodegradacji nie ulega...
-
The application of dynamic electrochemical impedance spectroscopy for stress corrosion cracking studies
PublikacjaElektrochemiczna Spektroskopia Impedancyjna (ESI) od wielu lat stanowi jedno z najważniejszych narzędzi wykorzystywanych do badania różnych procesów elektrochemicznych. Możliwość przeprowadzania badań w łącznej dziedzinie czasowo-częstotliwościowej ułatwia analizę pomiarów impedancyjnych w czasie. ESI pozwala również na analizę mechanizmu procesów elektrochemicznych w dziedzinie czasu z uwzględnieniem bardzo szybkich zjawisk, takich...
-
The application of Gabor transformation in the harmonic analysis of corrosion processes.
PublikacjaZaproponowana została nowa metoda analizy widmowej niestacjonarnych procesów korozyjnych. Analizie poddany został układ modelujący pierwszorzędową reakcję elektrodową. Wykazano, że w przypadku pobudzenia układu liniowo zmieniającym się potencjałem z nałożoną składową sinusoidalną przekształcenie Fouriera nie odzwierciedla zmian amplitudy powstających składowych harmonicznych. Jako rozwiązanie zaproponowana została analiza...
-
The mixed EIS-EQCM method for investigation of electrodeposition and electrodissolution of copper in acidic solution
PublikacjaCelem pracy jest połączenie chronowoltimpedancjometrii i mikrograwimetrii dobadania procesu elektroosadzania i elektroredukcji miedzi w środowisku kwaśnym. Proces elektroosadzania i elektroredukcji miedzi w środowisku kwaśnym został wybrany jako przykład prostej reakcji elektrochemicznej, by sprawdzić wiarygodność metody. Przedstawiono nową, obiecującą technikę - EIS-EQCM - jako metodę badania procesów niestacjonarnych, przebiegających...
Rok 2006
-
Selection of measurement frequency in Mott-Schottky analysis of passive layer on nickel
PublikacjaPrzedstawiono zależności Mott'a - Schottky'ego dla różnych częstotliwości pomiarowych. Kształt uzyskanych zależności zależy od doboru tych częstotliwości. Związane jest to z tym, że stężenie defektów w warstwie pasywnej zależy od doboru częstotliwości. Metoda DEIS pozwala na uniknięcie tych niedogodności.
-
System monitorowania szybkości korozji instalacji wodnych - to jakość wody. Cz. II
PublikacjaW pracy opisano bezobsługowy system monitorowania korozji. W tym systemie pomiary szybkości korozji wykonywane są automatycznie przy pomocy odpowiednich cyfrowych kart pomiarowych a następnie poprzez bezprzewodowy system transmisji danych przesyłane na serwer http.Taki system został zainstalowany wspólnie przez Wydział Ochrony Środowiska UM Gdańsk i Katedrę Elektrochemii, Korozji i Inżynierii Materiałowej PG i monitoruje instalację...
-
System monitorowania szybkości korozji instalacji wodnych - to jakość wody. Cz.1
PublikacjaCelem monitorowania korozyjnego jest zastosowanie środków zaradczych, pozwalających na przedłużenie czasu eksploatacji instalacji i urządzeń, a także kontrola i ochrona środowiska oraz bezpieczeństwo ludzi. Pomiary szybkości korozji pozwalają przewidzieć powstanie perforacji i innych uszkodzeń korozyjnych. Monitorowanie pozwala także określić rozległość zagrożeń korozyjnych. Bardzo ważnym aspektem monitorowania korozyjnego jest...
-
The effect of tensile stresses on aluminium passive layer durability
PublikacjaW niniejszej pracy przedstawiono wyniki badań DEIS dotyczących wpływu naprężeń rozciągających na trwałość warstwy pasywnej aluminium A91050, prowadzonych w środowisku chlorków w temperaturze pokojowej.Zastosowana technika pozwoliła na wyznaczenie krytycznej wartości wydłużenia, przy której doszło do pęknięcia warstwy pasywnej na badanym stopie.
-
The method of detection of electromagnetic fields in ground
PublikacjaW prezentowanej metodzie, detekcja pola polega na pomiarach i analizie zmian rozkładu potencjału. Różnice potencjałów są mierzone jako napięcie pomiędzy elektrodami umieszczonymi w różnych pozycjach na powierzchni ziemi. Analiza tych napięć przy pomocy krótkoczasowej transformaty Fouriera STFT umożliwia wyznaczenie zmian spektralnej gęstości mocy sygnału w funkcji czasu. Ten rodzaj łącznej analizy czasowo-częstotliwościowej daje...
-
Using impedance spectroscopy to characterize and monitor protection aspects of organic coating systems on metal
PublikacjaOrganiczne powłoki ochronne stosowane są powszechnie do ochrony konstrukcji metalowych przed korozją i zużyciem mechanicznym. W pracy zaproponowano nowy typ sensora impedancyjnego, który może być zastosowany do ciągłej oceny właściwości barierowych i adhezyjnych systemów powłokowych w warunkach terenowych w sposób nieniszczący, bez konieczności stosowania naczyń z elektrolitem. Przedstawiono koncepcję czujnika oraz przykładowe...
-
Wpływ cyklicznych naprężeń mechanicznych na trwałość organicznych powłok ochronnych
PublikacjaTematem pracy jest wpływ cyklicznych naprężeń mechanicznych na właściwości ochronne organicznych powłok przeciwkorozyjnych. Zbadano dynamikę procesu niszczenia zmęczeniowego powłok poddanych powtarzającym się napężeniom zginającym o różnych częstotliwościach. Odporność powłok nowych porównano z powłokami poddanymi procesom starzenia fizycznego (poprzez ekspozycję na promieniowanie UV lub na podwyższoną temperaturę). W pracy wykazano,...
-
Wykorzystanie dynamicznej elektrochemicznej spektroskopii impedancyjnej do badania procesu pękania warstwy pasywnej na austenitycznej stali wysokostopowej AISI 304L
PublikacjaCelem pracy było wykazanie, iż dynamiczna elektrochemiczna spektroskopia impedancyjna (DEIS) może być z powodzeniem wykorzystana do badania procesu pękania warstwy pasywnej na wysokostopowej stali AISI 304L w warunkach jednoczesnego działania naprężeń mechanicznych oraz agresywnego środowiska korozyjnego. W oparciu o przeprowadzone badania oraz uzyskane wyniki można uznać tą technikę za dobre narzędzie elektrochemiczne służące...
Rok 2022
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublikacjaThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
The valance state of vanadium-key factor in the flexibility of potassium vanadates structure as cathode materials in Li-ion batteries
PublikacjaPotassium hexavanadate (K2V6O16·nH2O) nanobelts have been synthesized by the LPE-IonEx method, which is dedicated to synthesis of transition metal oxide bronzes with controlled morphology and structure. The electrochemical performance of K2V6O16·nH2O as a cathode material for lithium-ion batteries has been evaluated. The KVO nanobelts demonstrated a high discharge capacity of 260 mAh g−1, and long-term cyclic stability up to 100...
Rok 2023
-
Sensing the onset of epoxy coating degradation with combined Raman spectroscopy/atomic force microscopy/electrochemical impedance spectroscopy
PublikacjaThe paper presents the results of investigation on epoxy resin durability upon 12-week exposure to UV radiation. The aim was early determination of the onset of epoxy degradation and for this purpose an epoxy film on steel substrate systems were periodically inspected using Raman spectroscopy, atomic force microscopy and electrochemical impedance spectroscopy. The behaviour of examined polymer could be divided into three periods: immunity,...
-
The Application of Dynamic Electrochemical Impedance Spectroscopy (DEIS) Technique in Corrosion and Corrosion Inhibition Studies
Publikacjaorrosion studies have attracted considerable interest in the areas of materials chemistry and industrial chemistry, as it affects the direct and indirect costs of industry, leading to huge economic setbacks due to the need for repair, maintenance, and even shutdowns due corrosion damage. This new volume is a comprehensive resource that presents new and up-to-date, theoretical, and experimental corrosion inhibition studies.
-
The Effect of C45 Carbon Black-Phosphomolybdic Acid Nanocomposite on Hydrogenation and Corrosion Resistance of La2Ni9Co Hydrogen Storage Alloy
PublikacjaIn this paper, we analysed the influence of corrosion processes and the addition of a carbon black-heteropoly phosphomolybdic acid (C45-MPA) nanocomposite on the operating parameters of a hydride electrode obtained on the basis of the intermetallic compound La2Ni9Co. The electrochemical properties of negative electrodes for NiMH batteries were studied using galvanostatic charge/discharge curves, the potentiostatic method, and electrochemical...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublikacjaMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
Rok 2011
-
Simulation and measurements for the substance identification by AFM
Publikacja -
Study of anticorrosion and microwave absprption properties of NiZn ferrite pigments
PublikacjaPurpose - The purpose of this paper is to report the electrochemical verification of anticorrosive properties of NiZn ferrites as pigments in protective coatings and evaluation of their microwave absorbing properties. Design/methodology/approach - Ferrites, represented by formula NixZn(1-x)Fe2O4, where x=0, 0.2, 0.4, 0.6, 0.8, 1.0, were synthesized using a ceramic method. The samples of ferrites were examined by X-ray diffraction...
-
Studying the effectiveness of a modernized cathodic protection system for an offshore platform
PublikacjaPrzedstawiono dokonaną modernizację starego systemu ochrony katodowej nóg platformy morskiej oraz omówiono wykonane badania skuteczności przeciwkorozyjnej zastosowanego rozwiązania. Modernizacja polegała na podłączeniu do nóg platformy układów anod galwanicznych umieszczonych na dnie morza. Skuteczność działania systemu oceniono na podstawie pomiarów profili potencjałowych nóg platformy. Po podłączaniu kolejnych układów anod...
-
Właściwości mechaniczne oraz przewodnictwo stałych elektrolitów poliuretanowych w zależności od metody ich otrzymywania i zawartości LiClO4 jako domieszki
PublikacjaElastomery poliuretanowe, stanowiące polimerowa matrycę badanych układówsyntetyzowano w dwu różnych wariantach z wykorzystaniem jako surowców 4,4'-diizocyjanianu difenylenometanu (MDI), oligo(oksytetrametyleno)diolu (PTMG) i 1,4-butanodiolu(BDO). Otrzymane stałe elektrolity poliuretanowe scharakteryzowano metodą spektroskopiiFTIR-ATR oraz zbadano ich stayczne i dynamiczne właściwości mechaniczne i gęstość. Przewodnictwo jonowe...
-
Wpływ mechanicznych naprężeń statystycznych i dynamicznych na trwałość i właściwości antykorozyjne warstw pasywnych.
PublikacjaBadania procesu pękania korozyjnego głównie skupiają się na długotrwałych badaniach niszczących, które wymagają zaangażowania wysokich kosztów związanych z wykorzystaniem aparatury badawczej oraz z jej obsługą techniczną. Opierając się na modelu pękania warstw pasywnych w którym czynnikiem wpływającym na proces inicjacji pękania korozyjnego jest pękanie warstwy pasywnej, wykonano badania właściwości mechanicznych warstw pasywnych...
-
Wpływ stopnia dewulkanizacji odpadów gumowych na wybrane właściwości modyfikowanego asfaltu drogowego
PublikacjaW niniejszej publikacji przedstawiono wyniki badań wpływu warunków dewulkanizacji odpadów gumowych na wybrane właściwości asfaltów drogowych, co umożliwia charakterystykę oddziaływań asfalt-dewulkanizat.
Rok 2014
-
Simultaneous impedance and volumetric studies and additionally potentiodynamic polarization measurements of molasses as a carbon steel corrosion inhibitor in 1M hydrochloric acid solution
PublikacjaThe inhibition effect of molasses on the corrosion of low carbon steel in 1M hydrochloric acid solution was investigated by volumetric and electrochemical measurements. Potentiodynamic polarization and dynamic electrochemical impedance spectroscopy (DEIS) results were obtained and compared with to those, obtained with the hydrogen evolution technique. All results indicate that molasses functioned as a good inhibitor in 1M hydrochloric...
-
The inhibition effect of mad Honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution
PublikacjaThe inhibition effect of mad honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution was investigated by Tafel extrapolarisation (TP), electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). All the studied parameters exhibited good anti-corrosive properties against corrosion of 2007-type aluminium alloy in the test solution; the corrosion rates decreased with the increase...
-
WYKONANIE BADAŃ I POMIARÓW POWŁOK ANTYKOROZYJNYCH ZABEZPIECZAJĄCYCH ELEMENTY METALOWE KONSTRUKCJI STALOWYCH, APARATÓW I URZĄDZEŃ INSTALACJI ODZYSKU OPARÓW BENZYN W BAZIE PALIW GRUPY LOTOS S.A. w POZNANIU
PublikacjaPrzeprowadzono inspekcję powłok malarskich na konstrukcji odzysku oparów w bazie Paliw Płynnych Grupy Lotos. Na podstawie wyników inspekcji przedstawiono wnioski i zalecenia związane ze stanem powłok i ich ewentualną naprawą.
Rok 2021
-
Sodium nitrite as a corrosion inhibitor of copper in simulated cooling water
PublikacjaThe corrosion inhibition behavior of sodium nitrite (NaNO2) towards pure copper (99.95%) in simulated cooling water (SCW) was investigated by means of electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). NaNO2 interferes with metal dissolution and reduce the corrosion rate through the formation or maintenance of inhibitive film on the metal surface. Surface morphologies illustrated...
-
Spectacular Oxygen Evolution Reaction Enhancement through Laser Processing of the Nickel‐Decorated Titania Nanotubes
PublikacjaThe selective, laser‐induced modification of the nickel‐decorated titania nanotubes provides remarkable enhancement toward oxygen evolution reaction. Particularly, the irradiation of the laterally spaced crystalline TiO2 nanotubes, results in the formation of the tight closure over irradiated end, preserving their hollow interior. The shape of the absorbance spectra is modulated along with applied energy, and the new absorption...
-
Studies on Aminoanthraquinone-Modified Glassy Carbon Electrode: Synthesis and Electrochemical Performance toward Oxygen Reduction
PublikacjaIn this paper, 9,10-anthraquinone (AQ) derivative-modified glassy carbon (GC) electrodes werestudied towards the electrochemical reduction of oxygen in aqueous and non-aqueous solutions. The reaction of 1-chloro-9,10-anthraquinone with aliphatic diamines was applied for the synthesis of amino-9,10-anthraquinone derivatives. The obtained AQ derivatives were grafted onto the surface of glassy carbon electrodes by electropolymerisation...
-
The Effect of Increasing the Amount of Indium Alloying Material on the Efficiency of Sacrificial Aluminium Anodes
PublikacjaAl-Zn-In alloys having 4.2% zinc content and various indium content in the range of 0.02–0.2% were tested with respect to the most important electrochemical properties of sacrificial anodes in a cathodic protection, i.e., the current capacity and potential of the operating anode. The distribution of In and Zn in the tested alloys was mapped by means of the EDX technique, which demonstrated that these elements dissolve well in the...
-
Ultrasonic-assisted Electrodeposition of Cu-Sn-TiO2 Nanocomposite Coatings with Enhanced Antibacterial Activity
PublikacjaCopper-based coatings are known for their high antibacterial activity. In this study, nanocomposite Cu–Sn–TiO2 coatings were obtained by electrodeposition from an oxalic acid bath additionally containing 4 g/dm3 TiO2 with mechanical and ultrasonic agitation. Ultrasound treatment was performed at 26 kHz frequency and 32 W/dm3 power. The influence of agitation mode and the current load on the inclusion and distribution of the TiO2...
Rok 2017
-
Structural, thermal and physico-mechanical properties of polyurethane/brewers’ spent grain composite foams modified with ground tire rubber
PublikacjaIn this work, brewers’ spent grain (BSG) and ground tire rubber (GTR) waste fillers were applied as low-cost reinforcement phase in rigid polyurethane foam (PUR). PUR/BSG/GTR composites were prepared by a single step method, using polyglycerol as partial substitute of commercially available petrochemical polyols. Foaming parameters, chemical structure, dynamic mechanical properties, thermal stability, physico-mechanical properties...
-
Time evolution of Electrochemical Impedance spectra of cathodically protected steel in artificial seawater
PublikacjaUsability of Electrochemical Impedance Spectroscopy data for better cathodic protection control was investigated. Carbon steel – S235JR2 grade specimen were exposed in artificial seawater environment. Samples were polarized and their potentials corresponded to four different cathodic protection degrees. Time evolution of Electrochemical Impedance spectra was investigated. Goodness of fit function (X2) was analysed in terms of proper...
-
Wyjaśnienie przyczyn korozji rur kotła, wytwornicy pary technologicznej instalacji Olefiny
PublikacjaWykonano badania przyczyn korozji rurek wytwornicy pary instalacji Olefiny. Przeprowadzono badania metalograficzne oraz SEM i EDX produktów korozji
-
Wykonanie czujnika LPR oraz dobór materiałów konstrukcyjnych w instalacji wody morskiej
PublikacjaWykonano analizę pracy systemu monitorowania korozji, dokonano wymiany czujnika. Zamontowano nowy czujnik z opcją pomiaru kuponowego w celu doboru materiałów konstrukcyjnych do instalacji wody morskiej.
-
Wykonanie oceny stanu wykładziny chemoodpornej wieży Absorbcyjnej T102 Solinox
PublikacjaPrzeprowadzono szczegółowe badania wykładziny chroniącej wewnętrzną częśc absorbera SO2. Na podstawie wykonanych badań i pomiarów zaproponowano alternatywne metody poprawy jakosci wykładziny.
Rok 2012
-
Study of Direct Methanol Fuel Cell Process Dynamics Using Dynamic Electrochemical Impedance Spectroscopy
PublikacjaA new technique, which was developed to characterize the direct methanol fuel cell under work conditions, has been presented in this paper. The impedance measurements were made using dynamic electrochemical impedance spectroscopy research technique in the galvanostatic mode, using multiple sinusoidal excitation. Obtained results show, that together with an increase of the temperature and working load, the global impedance...
Rok 2013
-
Study of the formation of calcareous deposits on cathodically protected steel in Baltic sea water
PublikacjaPurpose – The purpose of this paper is to investigate whether the sedimentation of calcareous deposits occurs on cathodically protected steel in Baltic sea water. Design/methodology/approach – Steel electrodes were cathodically polarized in natural Baltic sea water at potential þ0.150 V vs Zn electrode in potentiostatic mode. During exposure chronoamperometric measurements were carried out. After the exposure, the electrode’s surface...
-
Wykonanie badań wymalowań (w szczególności badań przyczepności) na konstrukcji w Narvie (Estonia) i wyjaśnienie przyczyn obserwowanych uszkodzeń
PublikacjaDokonano oglądu wizualnego i wykonano badania normowe na wymalowaniach na obiekcie budowanej elektrowni w Narvie (Estonia). Pobrano również próbki farb stosowanych do wymalowań oraz fragment elementu konstrukcji do badań.
Rok 2009
-
The determination and identification of stray current source influences on buried pipelines using time/frequency analysis
PublikacjaZaprezentowano metodę detekcji źródła interferencji prądów błądzących na rurociągach podziemnych w aglomeracjach miejskich z wykorzystaniem łącznej analizy czasowo-częstotliwościowej mierzonych sygnałów. Badania przeprowadzono na rurociągu podziemnym zlokalizowanym w sąsiedztwie dwóch trakcji elektrycznych: tramwajowej i kolejowej. Wyniki analiz zaprezentowano w formie spektrogramów, które ilustrują zmiany spektralnej gęstości...
-
Wpływ biocydu na właściwości przeciwkorozyjne preparatu stosowanego do korekcji wody w przemysłowych układach chłodzenia
PublikacjaStosowanie biocydów w układach chłodzenia jest konieczne ze względu na zapobieganie powstawaniu biofilmu i zarazem występowania niepożądanego zjawiska biokorozji.Praca obejmuje wyniki badań korozyjnych, grawimetrycznych, potencjodynanicznych oraz polaryzacji cyklicznej roztworu preparatów BIOFOSFOMAR, bedacego wielofunkcyjnym środkiem przeznaczonym do uzdatniania wody w układach chłodzenia
Rok 2010
-
The influence of UV light on Performance of poly(methyl methacrylate) in regard to dyesensitised solar cells
PublikacjaNiskie kosztu produkcji i prosta budowa Barwnikowych Ogniw Słonecznych (ang.DSSC-Dye Sensitized Solar Cells) a także porównywalne wydajności czynią je konkurencyjnymi wsród komercyjnych technologii ogniw słonecznych. Jednym z elementów wchodzących w skład BOS jest transparentne szkło przewodzące stanowiące jego elektrody. Doskonała transparentność omozliwia zastosowanie polimeru PMMA jako substytutu transparaentnego szkła przewodzącego....
-
Use of electrochemical methods to examine different surface preparation methods for organic coatings on steel
PublikacjaObróbka strumieniowo - ścierna jest jedną z powszechnie stosowanych metod przygotowania powierzchni. Wśród nowoczesnych metod coraz większe zainteresowanie wzbudza przygotowanie powierzchni wodą pod wysokim ciśnieniem (z ang. waterjetting). W porównaniu z konwencjonalnymi metodami ''waterjetting'' jest nowoczesną oraz przyjazną środowisku metodą. W literaturze brakuje informacji na temat skuteczności owej metody do zastosowań...
-
Wpływ zawartości jonów chlorkowych w brzeczce i piwie na korozję wżerową instalacji browarniczych
PublikacjaPrzedstawiono wyniki badań wpływu zawartości jonów chlorkowych w piwie na zagrożenie korozja wżerową stali stopowej. Badania wskazują, że wzrost stężenia jonów chlorkowych zwiększa zagrożenie korozją wżerową, występuje brak prostej korelacji pomiędzy zawartością jonów chlorkowych a podatnością stali na korozję.
Rok 2018
-
Up-conversion white emission and other luminescence properties of a YAG:Yb2O3·Tm2O3·Ho2O3@SiO2 glass-nanocomposite
PublikacjaWe report on a glass-nanocomposite material consisting of yttrium aluminum garnet (Y3Al5O12, YAG) nanocrystals co-doped with Yb3+, Tm3+ and Ho3+ ions as well as entrapped into a SiO2 xerogel. This 94YAG·5Yb2O3·0.8Tm2O3·0.2Ho2O3@SiO2 (abbr. YAG:YbTmHo@SiO2) nanocomposite material has been prepared by sol–gel procedure. Its structure and morphology has been characterized by means of X-ray diffraction (XRD) and scanning electron microscope...
-
Water uptake in protective organic coatings and its reflection in measured coating impedance
PublikacjaWater uptake in commercially available epoxy coating on mild steel using impedance spectroscopy and gravimetry was studied. The water content in the coating was determined using the Brasher-Kingsbury equation and various methods of coating capacitance calculation used in the literature. The obtained results were compared with reference gravimetric data. An overestimation of values obtained from impedance data in relation to gravimetric...
-
Wykorzystanie potencjometrów cyfrowych do testowania metod dynamicznej spektroskopii impedancyjnej
PublikacjaPrzedmiotem artykułu jest opracowanie modelu układu elektrochemicznego o zmiennej w czasie impedancji. Do konstrukcji modelu wykorzystano potencjometry cyfrowe sterowane mikrokontrolerem, pozwala to programowo kontrolować zmiany impedancji modelu. Odpowiednie ukształtowanie zmian widm impedancyjnych w funkcji czasu (impedancjogramów) pozwala na ustalenie ograniczeń różnych metod pomiaru impedancji.
Rok 2008
-
Zagrożenia korozyjne instalacji sterylizacyjnych
PublikacjaOpisano zagrożenia związane z korozją stali specyfikowanych do budowy instalacji sterylizacyjnych oraz wskazano na metody ich detekcji.