Filters
total: 6460
filtered: 4640
displaying 1000 best results Help
Search results for: surface topography measurements
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Actual field corrosion rate of offshore structures in the Baltic Sea along depth profile from water surface to sea bed
PublicationThe paper presents the results of field electrochemical investigations on the corrosion rate of carbon steel in seawater of the Baltic Sea at the location of the Baltic Beta production rig. The measurements were conducted throughout the year in seawater at different depths from the sea surface to the sea bed (about 75 m). The results revealed corrosion aggressiveness of the seawater along the entire depth profile. There was...
-
Organic Pollution in Surface Waters from the Fuglebekken Basin in Svalbard, Norwegian Arctic
PublicationThe Fuglebekken basin is situated in the southern part of the island of Spitsbergen (Norwegian Arctic), on the Hornsund fjord (Wedel Jarlsberg Land). Surface water was collected from 24 tributaries (B1-B24) and from the main stream water in the Fuglebekken basin (25) between 10 July 2009 and 30 July 2009. The present investigation reveals the results of the analysis of these samples for their PAH and PCB content. Twelve of 16 PAHs...
-
Non-Destructive Testing of the Longest Span Soil-Steel Bridge in Europe—Field Measurements and FEM Calculations
PublicationThe article describes interdisciplinary and comprehensive non-destructive diagnostic tests of final bridge inspection and acceptance proposed for a soil-steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure short-term response was collected. Periodic diagnostics of bridge deformations was done one...
-
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła (IPHC).
-
Novel applications of noise measurements in technology and sensing.
PublicationPomiary szumów są źródłem informacji oraz rodzajem badań nieniszczących dotyczących jakości elementów elektronicznych oraz innych materiałów. Mogą one poprawić selektywność i czułość wykrywania gazów oraz pozwalają monitorować zjawiska korozji. W tym celu wyznacza się właściwości statystyczne fluktuacji prądu lub napięcia w zakresie małych częstotliwości. W artykule przedstawiono i przedyskutowano wybrane, ze względu na ich znaczenie...
-
Measurements of differential cross sections in the backscattering region
PublicationW pracy przedstawiono przegląd technik eksperymentalnych umożliwiających detekcję elektronów rozproszonych w przedziale dużych kątów rozproszenia, ze szczególnym uwzględnieniem techniki lokalnego pola magnetycznego. Przedstawione zostały wyniki pomiarów i obliczeń teoretycznych różniczkowych przekrojów czynnych dla dużych kątów rozproszenia elektronów na atomach gazów szlachetnych i małych molekuł.
-
Mobile satellite measurements on the Pomeranian Metropolitan Railway
Publication -
<title>Measurements of nonlinear optical fibers</title>
Publication -
Optimization of transformation of measurements of ship hull blocks
PublicationArtykuł przedstawia analizę wyników pomiarów wykonanych na blokach kadłuba statku, aby ocenić ich przydatność montażową podczas ostatniej fazy montażu w suchym doku lub na pochylni. Analiza realizowana jest w dwóch krokach. Najpierw sprawdza się, czy bloki zostały wykonane z zachowaniem wymaganych tolerancji, a następnie czy istnieje możliwość połączenia ze sobą dwóch sąsiednich bloków. Ponieważ każdy blok jest mierzony w innym...
-
Mobile system for on-road measurements of air pollutants
PublicationW pracy zaprezentowano prototyp mobilnej stacji diagnostycznej do pomiarów stężeń typowych zanieczyszczeń powietrza (C6H6, NO2, NOx, CO i CO2) pochodzących z komunikacji w miastach. Nowością proponowanego systemu jest możliwość przeprowadzania pomiarów emisji zanieczyszczeń wzdłuż ciągów komunikacyjnych i w miejscach, w których nie mogą być zastosowane stacjonarne stacje monitoringowe. W proponowanym rozwiązaniu, urządzenie...
-
Fluorescence Measurements for chemical optical sensor of cobalt
PublicationW pracy zaproponowano i opisano optoelektroniczny fluorescencyjny sensor do pomiaru stężenia kobaltu w wodzie.
-
Temperature Measurements in Monitoring of Large Thrust Bearings
PublicationW pracy przedstawiono krytyczną ocenę popularnego systemu diagnostyki dużych łożysk wzdłużnych (np. łożysk nośnych hydrogeneratorów), w którym stosowany jest jednopunktowy pomiar temperatury w klockach łożyskowych. Stwierdzono, że taki układ pomiarowy nie pozwala na bezpieczną eksploatację łożysk, ponieważ posiada bardzo duże opóźnienie czasowe, nie daje informacji o lokalnych zagrożeniach, nie pozwala racjonalnie ustalić poziomów...
-
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła.
-
Damage detection in riveted structures by laser measurements
Publication -
Tire rolling resistance measurements on the road and in the laboratory
PublicationW pracy przedstawiono stanowisko bębnowe do badania oporu toczenia opon samochdowych w warunkach laboratoryjnych. Zaprezentowano także przyczepę dynamometryczną do badania oporu toczenia opon samochodowych w warunkach drogowych. Stanowisko bębnowe i przyczepa zosały zbudowane w Katedrze Pojazdów i Maszyn Roboczych Politechniki Gdańskiej. Omówiono wpływ wzdłużnego pochylenia drogi i naporu powietrza na badane koło na dokładność...
-
Measurements of the mechanical Barkhausen noise in ferromagnetic steels
PublicationArtykuł ten przedstawia wpływ zmian w mikrostrukturze stali P91, powstałych w skutek obróbki cieplnej, na właściwości mechanicznego efektu Barkhausena (MeBN). Parametry takie jak amplituda obwiedni napięcia skutecznego (RMS) MeBN oraz położenie maksimum tejże obwiedni porównywane są, pod kątem czułości na obróbkę cieplną materiału, z klasycznymi parametrami takimi jak pole koercji magnetycznej czy też twardość mechaniczna HV. Największą...
-
Impulse Impedance Measurements of Lightning Protection Earthings
PublicationLightning protection earthing systems should be tested at currents with time parameters similar to those of lightnings. A method and definition of a measured value of impulse impedance are introduced. The impulse impedance was determined by a quotient of voltage drop on the tested earthing to a value of current in measure circuit. The usefulness of the impulse method for lightning protection evaluation is tested on radio base stations...
-
Microscopic parameters of gas via acoustic measurements
PublicationProponujemy wstępną analizę odwrotnego problemu, który sformułowano, opartą na statycznej mechanice /termodynamice, rozważającej gaz jako środek rozprzestrzeniania dzwięku.
-
Impedance measurements of coating properties on bridge structures
PublicationPomiary impedancyjne pozwalają na prostą ocenę właściwości ochronnych powłok ochronnych i wykładzin. Pomiary stosuje się w celu porównania powłok, monitorowania ich właściwości i oceny mechanizmu działania. Metodyka jest z powodzeniem stosowana w pomiarach laboratoryjnych. Pomiary terenowe są bardziej skomplikowane ponieważ wymagają w pełni kontrolowanych komputerowo przyrządów, kontroli warunków pogodowych oraz wielu innych parametrów...
-
Assessment of Adjustment of GNSS Railway Measurements with Parameter-Binding Conditions in a Stationary Scenario
PublicationThe study aims to assess the applicability of the ordinary least squares method, robust estimation, and conditions-binded adjustment in processing the six synchronous coordinate pairs of global navigation satellite system (GNSS) receivers. The research is part of the research project InnoSatTrack, focused on the enhancement of the determination of geometrical parameters of railway tracks using GNSS, inertial, and other sensors....
-
Bridge Non-Destructive Measurements Using a Laser Scanning during Acceptance Testing: Case Study
PublicationOwing to the recent proliferation of inventory works on roads and railways, bridge acceptance tests have increased exponentially. These tests’ results are often misinterpreted owing to the use of various measuring equipment types, rendering integrated interpretation problematic. It is also problematic that adjusting the measurement method is difficult when the structure’s response to load is uncertain. Therefore, it is important...
-
Time-Gating method with automatic calibration for accurate measurements of electrically small antenna radiation patterns in Non-Anechoic environments
PublicationNon-anechoic sites represent a cheap alternative to measurements of antennas in dedicated facilities. However, due to a high noise—from the external EM signal sources and multipath interferences—the quality of radiation patterns obtained in non-anechoic conditions is poor. The characteristics can be corrected using a time-gating method (TGM), which involves filtering of the noise based on temporal analysis of the measured signals....
-
Study on the Positioning Accuracy of the GNSS/INS System Supported by the RTK Receiver for Railway Measurements
PublicationCurrently, the primary method for determining the object coordinates is positioning using Global Navigation Satellite Systems (GNSS) supported by Inertial Navigation Systems (INS). The main goal of this solution is to ensure high positioning availability, particularly when access to satellite signals is limited (in tunnels, areas with densely concentrated buildings and in forest areas). The aim of this article is to determine whether...
-
Extraction and evaluation of gas-flow-dependent features from dynamic measurements of gas sensors array
PublicationGas analyzers based on gas sensors are the devices which enable recognition of various kinds of volatile compounds. They have continuously been developed and investigated for over three decades, however there are still limitations which slow down the implementation of those devices in many applications. For example, the main drawbacks are the lack of selectivity, sensitivity...
-
Optimization of the Relative Humidity of Reactant Gases in Hydrogen Fuel Cells Using Dynamic Impedance Measurements
PublicationWater management is a key factor affecting the efficiency of proton exchange membrane fuel cells (PEMFCs). The currently used monitoring methods of PEMFCs provide limited information about which processes or components that humidity has a significant impact upon. Herein, we propose the use of a novel approach of impedance measurements using a multi-sinusoidal perturbation signal, which enables impedance measurements under dynamic...
-
Comparison of noise reduction methods in radiometric correlation measurements of two-phase liquid-gas flows
PublicationTwo-phase liquid-gas flows occur frequently in the mining, energy, chemical, and petrochemical industries. One of non-contact methods used to analyse these flows is the gamma ray absorption method. However, the signals received from radiation detectors contain a significant stochastic noise, which makes them difficult to analyse. The article describes four methods of noise reduction in cross-correlation measurements of water-air...
-
Computer-Aided Design of Railroad Horizontal Arc Areas in Adapting to Satellite Measurements
PublicationThis paper presents a method of designing railway sections located in horizontal arcs. The adopted procedure is universal, i.e., it creates the possibility of varying both the type and the length of the assumed transition curves. This means that the applied analytical formulas apply to the boundary conditions of the transition curves and all of the simplifications widely existing in common algorithms have been eliminated. The presented...
-
Characterizing surface and air temperature in the Baltic Sea coastal area using remote sensing techniques and GIS
PublicationEstimation of surface temperature using multispectral imagery retrieved from satellite sensors constitutes several problems in terms of accuracy, accessibility, quality and evaluation. In order to obtain accurate results, currently utilized methods rely on removing atmospheric fluctuations in separate spectral windows, applying atmospheric corrections or utilizing additional information related to atmosphere or surface characteristics...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublicationIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
Electron-scattering cross sections for selected alkyne molecules: Measurements and calculations
PublicationWe report cross-section results from experimental and theoretical studies on electron collisions with 1-butyne (HC≡C–CH2CH3) and acetylene (HC≡CH) molecules and from computations for a propyne (HC≡C–CH3) molecule. Absolute grand -total electron-scattering cross sections (TCSs) were measured at impact energies ranging from about 0.5 to 300 eV using the linear electron-transmission method. The TCS energy curve for 1-butyne has a...
-
The influence of humic substances in treated sewage on the quality of surface waters
PublicationAt present the evaluation of WWTP effectiveness is based upon organic matter and nutrients removal. Recently it was found out that sewage treatment leads to formation of resistant to biochemical degradation organic compounds, similar to humic acids. The humic acids formed during sewage treatment process play diversified functions when discharged to surface waters - for instance they can act as carriers of hydrophobic organic pollutants...
-
Galvanostatic impedance measurements for the efficient adsorption isotherm construction in corrosion inhibitor studies
PublicationWe present an approach towards an accurate and time-efficient adsorption isotherm determination to evaluate the corrosion inhibitor interaction in electrolytic environments. The approach is based on dynamic impedance spectroscopy measurements in galvanostatic mode (g-DEIS). The studied corrosion inhibitor is continuously injected between the secondary cell and the corrosion cell. The efficiency corresponding to instantaneous inhibitor...
-
Blade Section Prpfile Array Lifting Surface Design Method for Marine Screw Propeller Blade
PublicationThe lifting surface model is widely used in screw propeller design and analysis applications. It serves as a reliable tool for determination of the propeller blade mean line and pitch distribution. The main idea of this application was to determine the blade shape that would satisfy the kinematic boundary condition on its surface with the prescribed bound circulation distribution over it. In this paper a simplified lifting surface...
-
Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet
PublicationThis paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC61BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number...
-
Overflowing tests at the Polish DredgDikes research dike – stability of the dike surface against erosion
PublicationIn the project DredgDikes the different research dike embankments were tested with respect to overflowing water induced erosion. Therefore, flumes were installed on the land side embankments in which the effect of overflowing water on the vegetated surface was investigated. On the Polish DredgDikes research dike near Gdansk, Poland, two parallel flumes were installed and the surface of the dike made of different mixtures of...
-
Wireless Local Area Network Technologies as Communication Solutions for Unmanned Surface Vehicles
PublicationAs the number of research activities and practical deployments of unmanned vehicles has shown a rapid growth, topics related to their communication with operator and external infrastructure became of high importance. As a result a trend of employing IP communication for this purpose is emerging and can be expected to bring significant advantages. However, its employment can be expected to be most effective using broadband communication...
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublicationIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Comparison of the impact test and the harmonic test in measurements of natural resonant frequencies of circular saw blades
PublicationIn this paper results of measurements of natural resonant frequencies of circular saw blades with the impact test and the harmonic test are presented. Comparison of these two methods revealed that during testing of circular saw blades, in which bodies the open and closed notches (cuts) for cleaning of knives are present, with the harmonic test method it has been observed appearing of quasi-twin resonant frequencies, whereas the...
-
The surface photoconductivity in molecular layers
PublicationW pracy przedstawiono rezultaty analizy fotoprądów powierzchniowych w cienkich warstwach tetracenu i pentacenu. W szczególności badano wpływ obecności defektów strukturalnych w warstwach na charakterystyki fotoprądów i transport nośników ładunku.
-
Phonons at the Fe(110) Surface
Publication -
Spikes removal in surface measurement
Publication -
Dynamics of surface floating objects
PublicationPrezentowana praca stanowi wstępne rozeznanie w dziedzinie badań dynamiki konstrukcji pływających z zastosowaniem teorii procesu dyfuzji. W pracy rozpatrywane są modele fizyczne jednostek wielokadłubowych oraz modele matematyczne. Spośród modeli jednostek wielokadłubowych wyróżnia się modele deterministyczne oraz modele stochastyczne.
-
Surface properties of barley straw
PublicationWłaściwości powierzchniowe słomy jęczmiennej (Hordeum vulgare) odgrywają kluczową rolę w zastosowaniach przemysłowych, takich jak sorpcja rozlewów olejowych oraz oczyszczenie gleby. Zbadano niejednorodność chemiczną oraz morfologiczną liści i łodyg słomy jęczmiennej poprzez pomiar kątów zwilżania wodą oraz olejem oraz z zastosowaniem techniki FTIR, SEM oraz AFM.
-
Smoothing of wood surface by burnishing
PublicationW artykule zaprezentowano rozwój bezwiórowych metod obróbki wykańczającej drewna. Przedstawiono wpływ nagniatania ślizgowego na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach wykonanych z drzewa sosnowego toczonych i nagniatanych ślizgowo. Nagniatanie ślizgowe przeprowadzono z wykorzystaniem nagniataka elastycznego o elemencie ślizgowym wykonanym z Karbonado. Wyniki odniesiono do głównych parametrów nagniatania...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Dynamic Nanoimpedance Characterization of the Atomic Force Microscope Tip-Surface Contact
PublicationNanoimpedance measurements, using the dynamic impedance spectroscopy technique, were carried out during loading and unloading force of a probe on three kinds of materials of different resistivity. These materials were: gold, boron-doped diamond, and AISI 304 stainless steel. Changes of impedance spectra versus applied force were registered and differences in the tip-to-sample contact character on each material were revealed. To...
-
FEM approach to estimate the behaviour of biocomposite metal-surface coating system
PublicationA three dimensional (3D) model of biocomposite metal-surface coating system, which is influenced byknown external forces, is proposed. This model consists of the metallic substrate (Ti6Al4V) and thehydroxyapatite (HA) coating. Using FEM (finite element method), strain-stress maps of model weregenerated for investigating relations between the extreme stress of HA coating and the magnitude ofexternal force and the thickness of the...
-
INFORMATION ABOUT DYNAMICS OF THE SEA SURFACE AS A MEANS TO IMPROVE SAFETY OF THE UNMANNED VESSEL AT SEA
PublicationOne of the fundamental states of the sea surface is its heave. Despite of years of the intense scientific inquiry, no clear understanding of the influence of this aspect on the dynamics of the sea environment has emerged. The separation of two nearby fluid elements which one may observed for example as a free floating of small objects on the sea surface (rescuers on the rough sea or small research vessels) is caused by the interaction...
-
The use of Response Surface Methodology for reliability estimation of aluminum silo subjected to wind load
PublicationAn axisymmetric aluminum silo model with a single, standardized geometric imperfection of its lateral surface is considered. The silo is wind – loaded only. The paper is focused on the critical, or limit value of wind pressure, both producing a loss of stability of the silo. This value is affected by vertical coordinate (position) of the imperfection and the angular relation between the imperfection and the wind direction. Reliability...