Filters
total: 1895
filtered: 1498
displaying 1000 best results Help
Search results for: AXLE LOAD SPECTRA
-
Instrumented end notched flexure - Crack propagation and process zonemonitoring Part II: Data reduction and experimental
PublicationA mode II instrumented end notched flexure three point bending (ENF) adhesion test is described. The adhesive joint consists of two aluminium alloy (AW7075-T6) plates bonded with a structural epoxy adhesive (Hysol EA 9395™). Strain gauges are attached to the outer surface (backface) of the substrates in the lengthwise direction to measure local surface strain during crack propagation. Simultaneously, load/displacement measurements...
-
Hybrid geothermal-fossil power cycle analysis in a Polish setting with a focus on off-design performance and CO2 emissions reductions
PublicationGrowing demand for electricity due to economic development contributes to increased greenhouse gas production, especially CO2. However, emissions can be limited by enhancing the efficiency of primary energy conversion, such as integrating geothermal energy into coal-fired power plants. Therefore, this paper proposes replacing conventional feed-water heaters with geothermal preheaters to create a hybridized system. This study was...
-
Some Aspects of Shear Behavior of Soft Soil–Concrete Interfaces and Its Consequences in Pile Shaft Friction Modeling
PublicationThis paper examines the stiffness degradation and interface failure load on soft soil–concrete interface. The friction behavior and its variability is investigated. The direct shear tests under constant normal load were used to establish parameters to hyperbolic interface model which provided a good approximation of the data from instrumented piles. Four instrumented piles were used to obtain reference soil–concrete interface behavior....
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
Lagrangian model of an isolated dc-dc converter with a 3-phase medium frequency transformer accounting magnetic cross saturation
PublicationThis article presents a nonlinear equivalent circuit model of an isolated dc-dc converter with a 3-phase medium frequency transformer. The model takes into account the magnetic cross saturation of the 3-phase core-type magnetic circuit. The model is suitable in detailed electromagnetic transient simulations of power systems involving isolated dc-dc converters. The model is developed using the Lagrange energy method. It involves...
-
A Comparison of the Efficiency of Deammonification under Different Aeration Strategies in a Laboratory-Scale Sequencing Batch Reactor
PublicationAn important source of nitrogen load entering the biological part of wastewater treatment plants (WWPTs) is derived from the anaerobic sludge digestion processes. Sludge digestion liquors constitute only 1-2% of the inflow to the plant, but the load of nitrogen directed with them to the main stream may be as high as 10-20% of the total nitrogen load. Therefore, numerous studies have focused on treatment of sludge digestion liquors...
-
Investigation on Mode I Fracture Behavior of Hybrid Fiber-Reinforced Geopolymer Composites
PublicationRecent reports in the literature have shown that fber-reinforced geopolymer composites (FRGC) made with monofbers exhibit a signifcant enhancement in fracture energy. However, many aspects of the fracture performance of hybrid fberreinforced geopolymer composites (HFRGC) remain largely unexploited, and these are predominant for the structures. For the frst time, the mode I fracture energy of HFRGC is investigated. The mode I behavior...
-
Prediction of fracture toughness in fibre-reinforced concrete, mortar, and rocks using various Machine learning techniques
PublicationMachine Learning (ML) method is widely used in engineering applications such as fracture mechanics. In this study, twenty different ML algorithms were employed and compared for the prediction of the fracture toughness and fracture load in modes I, II, and mixed-mode (I-II) of various materials, including fibre-reinforced concrete, cement mortar, sandstone, white travertine, marble, and granite. A set of 401 specimens of “Brazilian...
-
Simulation Results of Dynamic Capacity Reallocation in Hierarchical Cell Structure of UMTS Network
PublicationIn the paper simulation results of dynamic capacity reallocation between different layers of hierarchical cell structure of UMTS network has been described. This approach for load management seems to be useful for improving the resource utilization perfmorance.
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublicationIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Influence of the particle size of carbonate-siliceous rock on the efficiency of phosphorous removal from domestic wastewater
PublicationtThe aim of the study was to determine the influence of the particle size of carbonate–silica rock (opoka)used in rock filters on the efficiency of phosphorus removal from domestic wastewater. The investigationswere carried out in a laboratory using a model consisting of three vertical flow filters with carbonate–silicarock of different particle sizes (G1= 1–2 mm; G2= 2–5 mm; G3= 5–10 mm). The tested rock was subjectedto decarbonising...
-
Non-Salient Brushless Synchronous Generator Main Exciter Design for More Electric Aircraft
PublicationThis paper presents a prototype of high speed brushless synchronous generators (BSG) design for the application in autonomous electric power generation systems (e.g., airplane power grid). Commonly used salient pole field of the main generator part of BSG was replaced with a prototype non-salient pole field. The main objective of the research is an investigation into the advantages and disadvantages of a cylindrical field of the...
-
MONITORING SYSTEM OF THE ROAD EMBANKMENT
PublicationThe paper presents the analysis of the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform with the embedded steel grid. This field investigation was to study the complex interaction among the columns, the load transfer platform layer, and steel grid via in situ measurements during erection and live loading of the embankment. The study was focused on the behaviour of steel...
-
Vibration monitoring of structures in the light of the Polish and international requirements
PublicationThe paper concerns the wide range of strategies used to protect structures against man-made dynamic excitation. The most popular approaches applied worldwide are compared, and the main differences and similarities are summarized. The literature studies are supported by the results of the measurements performed on different types of real structures, which are sensitive and insensitive to the dynamic load. To make the conclusions...
-
Structure and Molecular Dynamics in Renewable Polyamides from Dideoxy-Diamino Isohexide
PublicationThe chemical structure, the conformation, andthe flexibility of the polymer chain fragments present in thepolyamides synthesized from 2,5-diamino-2,5-dideoxy-1,4;3,6-dianhydrosorbitol, 1,4-diaminobutane, and either sebacic orbrassylic acid have been studied by liquid-state 2D NMRspectroscopy viz. correlation spectra (COSY) and heteronuclearmultiple-bond correlation spectra (gHMBC), by 13Ccross-polarization/magic-angle spinning...
-
Synthesis, spectroscopy and computational studies of some biologically important hydroxyhaloquinolines and their novel derivatives
PublicationA series crystalline compounds of methyl and phosphinyl derivatives of 2-methylquinolin-8-ol (1a) and related 5,7-dichloro-2-methylquinolin-8-ol (1b) were quantitatively prepared and characterized by microanalysis, IR, UV-vis and multinuclear NMR spectroscopy. Five of them have been characterized by single crystal X-ray diffraction method. The known compounds, 8-methoxy-2-methylquinoline (2a) and 8-methoxyquinoline (2d), were synthesised...
-
Evolution of Ag nanostructures created from thin films: UV–vis absorption and its theoretical predictions
PublicationAg-based plasmonic nanostructures were manufactured by thermal annealing of thin metallic films. Structure and morphology were studied using scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HR-TEM) and X-ray photoelectron spectroscopy (XPS). SEM images show that the formation of nanostructures is influenced by the initial layer thickness as well as the...
-
Rubrene Thin Films with Viably Enhanced Charge Transport Fabricated by Cryo-Matrix-Assisted Laser Evaporation
PublicationAmong organic semiconductors, rubrene (RB; C42H28) is of rapidly growing interest for the development of organic and hybrid electronics due to exceptionally long spin diffusion length and carrier mobility up to 20 cm2V−1s−1 in single crystals. However, the fabrication of RB thin films resembling properties of the bulk remains challenging, mainly because of the RB molecule’s twisted conformation. This hinders the formation of orthorhombic...
-
Photocatalytical properties of maze-like MoO3 microstructures prepared by anodization of Mo plate
PublicationIn this work, we present a simple method of the formation of MoO3 microstructures via an electrochemical anodization of Mo plate carried out under varied conditions. The morphology, composition and structure of samples were investigated by SEM, EDX, XRD and Raman spectroscopy. The band gap energy was estimated using the Kubelka–Munk function and was found to be 2.87 eV. Finally, the photocatalytic activities of MoO3 samples were...
-
New coordination polymers based on a V-shaped ligand and lanthanides: Structural description and symmetry-luminescence correlation using europium as a probe
PublicationWe have synthesized new luminescent coordination polymers using 4,4'-sulfonyldibenzoic acid (H2SDA) and several lanthanide ions by open crystallization in DMF. Three different 1-D structures were obtained, as determined by single-crystal X-ray diffraction: [La(η2-NO3)(μ-SDA)(DMF)3]n (1), [Sm(η2-NO3)(μ-SDA)(DMF)2 2DMF]n (3), [Ln(η2-NO3)(μ-SDA)(DMF)2 DMF]n (Ln ¼ Eu (4), Dy (5), Ho (6), Er (7), Tm (8) and Lu(9)). A 2-D structure,...
-
Novel, Fully Biobased Semicrystalline Polyamides
PublicationNovel, semicrystalline polyamides and co(polyamides) were synthesized from biobased sebacic acid (SA), 2,5-diamino-2,5-dideoxy-1,4;3,6-dianhydroiditol (diaminoisoidide, DAII) as well as from 1,4-diaminobutane (DAB), also known as putrescine in nature. Low molecular weight polyamides were obtained by melt polycondensation of the salts based on these monomers or by interfacial polycondensation. In order to increase their molecular...
-
Multifrequency Nanoscale Impedance Microscopy (m-NIM): A novel approach towards detection of selective and subtle modifications on the surface of polycrystalline boron-doped diamond electrodes
PublicationIn this paper, we describe the modification of Nanoscale Impedance Microscopy (NIM), namely, a combination of contact-mode atomic force microscopy with local impedance measurements. The postulated approach is based on the application of multifrequency voltage perturbation instead of standard frequency-by-frequency analysis, which among others offers more time-efficient and accurate determination of the resultant impedance spectra...
-
Computer-aided analysis of signals from a low-coherence Fabry-Perot interferometer used for measurements of biological samples
PublicationThe aim of the study was to develop an automated computer-aided system for analysis of spectrograms obtained from measurements of biological samples performed with a low-coherence Fabry-Pérot interferometer. Information necessary to determine dispersion characteristics of measured materials can be calculated from the positions of the maxima and minima that are present in their spectra. The main challenge faced during the development...
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublicationLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Static Series and Shunt-series PE Voltage-quality Controllers
PublicationAs presented in the Chap. 7 static shunt power electronics (PE) voltage-quality controllers protect the utility electrical system from the unfavorable impact of customer loads. Shunt controllers, as shown in Chap. 6, are recommended mainly for mitigation of the causes of disturbances, and not their effects in distanced nodes of a power-electronics system. In the case when reduction of disturbances effects is required, which leads...
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublicationOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
Motor Cable Influence on the Conducted EMI Emission of the Converter Fed AC Motor Drive. - Vol. 1
PublicationInvestigation of conducted electromagnetic interference in AC motor drives fed by pulse width modulated voltage converters requires considering parasitic capacitances in converters, motor windings and feeding cables to be taken into account. Motor voltage transients and related conducted electromagnetic emission are significantly correlated with resonance effects occurring in load circuits. The levels of intensity of these phenomena...
-
Experimental investigation of the PEM fuel cells performance for automotive and stationary applications
PublicationThe aim of the study was to provide dynamic characteristics of the PEM fuel cell system consisted of Nexa modules, provide steady-state characteristics of the for different values of air excess ratio and steady-state characteristics for different stack temperatures and given load.
-
Dynamic impedance measurements of the Direct Methanol Fuel Cell cathode at various operating temperatures
PublicationThis article discusses the application of impedance analysis for diagnosing the cathode of a direct methanol fuel cell at various operating temperatures. The Dynamic Electrochemical Impedance Spectroscopy technique coupled with a linear current scan was applied for this purpose. This technique allowed the observation of changes in the cathode's properties in the fuel cell operating under real working conditions. An equivalent model...
-
Flexomagnetic response of buckled piezomagnetic composite nanoplates
PublicationIn this paper, the equation governing the buckling of a magnetic composite plate under the influence of an in-plane one-dimensional magnetic field, assuming the concept of flexomagnetic and considering the resulting flexural force and moment, is investigated for the first time by different analytical boundary conditions. To determine the equation governing the stability of the plate, the nonlocal strain gradient theory has been...
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublicationAbstract: The mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also on the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete...
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublicationThe mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete Element Methods....
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublicationThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
The impact of material degradation on the resistance and reliability of truss structures
PublicationThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...
-
Dynamics of the small-span railway bridge under moving loads
PublicationThe paper presents the results of dynamic analysis of the small-span railway bridge, subjected to an action of moving trains. Numerical simulations were performed using three different load models: series of moving forces, series of moving single-mass and double-mass oscillators. The parameters of the vehicle were taken from the existing EN57 train. The parameters of the bridge were taken from the existing steel span of 10,24 m...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublicationThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
The silver layers in fiber-optic sensors
PublicationIn this paper a method of application of the silver layers on the surface of an optical fiber was proposed. The optical properties and surface quality of the silver layer was examined by optical microscopy. The reflection and transmission of the sample were investigated. To evaluate the silver mirror it was placed in a fiber optic Fabry-Perot interferometer and the quality of the spectra was analyzed. The commercial mirror was...
-
Correlated Particle Motion and THz Spectral Response of Supercritical Water
PublicationMolecular dynamics simulations of supercritical water reveal distinctly different distance-dependent modulations of dipolar response and correlations in particle motion compared to ambient conditions. The strongly perturbed H-bond network of water at supercritical conditions allows for considerable translationaland rotational freedom of individual molecules. These changes give rise to substantially different infrared spectra and...
-
Aggregation of Rhodamine 6G in titanium dioxide nanolayers and bulk xerogels
PublicationNanolayers and bulk xerogels of Rhodamine 6G (Rh6G) in titanium dioxide (Rh6G/TiO2) were prepared using the sol–gel method. The spectroscopic and structural properties of these two types of hybrid matrices were studied as a function of dye concentration. In both cases absorption, fluorescence and time resolved emission spectra show the formation of fluorescent aggregates. The observed stronger changes in characteristics of bulk...
-
The effect of depth of surface layers constituted by vacuum technologies on pitting
PublicationThe paper presents the results of a study of the effect of vacuum technologies of formation of surface layers on pitting of associated elements in a lubricated, heavy-load rolling contact. The study has shown that increase in a PVD coat depth is accompanied by decrease in the fatigue friction pair.
-
Niskokoherencyjne czujniki światłowodowe wykorzystujące cienkowarstwowe struktury nanodiamentowe
PublicationZnaczny rozwój technologii wytwarzania czujników światłowodowych spowodował, że są one powszechnie dostępne i stosowane w wielu gałęziach przemysłu, nauki oraz medycyny. Zastosowanie nowych materiałów w konstrukcji takich czujników niesie za sobą duży potencjał. Celem rozprawy jest przedstawienie możliwości wykorzystania cienkowarstwowych struktur nanodiamentowych w niskokoherencyjnych czujnikach światłowodowych, które poprawią...
-
Quasi-Static Response
PublicationConcern for the quasi-static response of ship and offshore structures, as required for safety and serviceability assessments. Attention shall be given to uncertainty quantification of quasi-static load and response analysis approaches, and their limitations, including exact and approximate methods for derivation of different acceptance criteria.
-
Spectroscopic study of atmospheric pressure 915 MHz microwave plasma at high argon flow rate
PublicationIn this paper results of optical emission spectroscopic (OES) study of atmospheric pressure microwave 915 MHz argon plasma are presented. The plasma was generated in microwave plasma source (MPS) cavity- resonant type. The aim of research was determination of electron excitation temperature Texc gas temperature Tg and electron number density ne. All experimental tests were performed with a gas flow rate of 100 and 200 l/min and...
-
Niobate in silicate and phosphate glasses: Effect of glass basicity on crucible dissolution
PublicationUsing niobium crucibles for melting phosphate and silicate glasses of various modifier oxide contents, and therefore varying optical basicity (Λ), was found to result in varying dissolution rates of niobate during melting. Because of their high electronic polarizability, even small concentrations of niobates are detectable in the Raman spectra of glasses. Even less than 1 mol% Nb2O5 can be identified, as independently confirmed...
-
Determination of the active ingredient in pharmaceutical gel formulation by NIR spectroscopy
PublicationPharmaceuticals of their intended must be thoroughly controlled. The traditional analytical methods are very costly and time consuming. NIR spectroscopy allows to analyze pharmaceutical materials very quickly and with very low costs. First pharmaceutical applications of the NIR spectroscopy appeared with some incuriosity in the late 1960s. Application of NIR in the contemporary pharmaceutical industry is very large. The most common...
-
Vibrational Sum-Frequency Generation Activity of a 2,4-Dinitrophenyl Phospholipid Hybrid Bilayer: Retrieving Orientational Parameters from a DFT Analysis of Experimental Data
PublicationThe vibrational nonlinear activity of films of 2,4-dinitrophenyl phospholipid (DNP) at the solid interface is measured by sum-frequency generation spectroscopy (SFG). Hybrid bilayers are formed by a LangmuirSchaefer approach in which the lipid layer is physisorbed on top of a self-assembled monolayer of dodecanethiol on Pt with the polar heads pointing out from the surface. The SFG response is investigated in two vibrational frequency...
-
Raman investigation of the patina layers on Hungarian copper ingots from a fifteenth century shipwreck
PublicationWe report results of the patina study of underwater archeological finding ofmedieval copper objects performed by means of the Raman and complementary spectroscopic techniques. The objects were found submerged in the sea as cargo part of the ship which sunk in the Gulf of Gdańsk in 1408. The excavated collection consists of 230 oval ingots of the size and mass up to about 60 cm and 18 kg (total of 2 tons), respectively. In the Raman...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Field investigation of low-temperature cracking and stiffness moduli on selected roads with conventional and high modulus asphalt concrete
PublicationHigh Modulus Asphalt Concrete (HMAC) was introduced in Poland as a one of the solutions to the problem of rutting, type of deterioration common in the 1990s. After first encouraging trials in 2002 HMAC was widely used for heavily loaded national roads and motorways. However some concerns were raised about low-temperature cracking of HMAC. This was the main reason of the studies presented in this article were started. The article...