Search results for: STRUCTURAL STUDIES
-
Numerical Determination of the Load-Bearing Capacity of a Perforated Thin-Walled Beam in a Structural System with a Steel Grating
PublicationThis article presents the results of numerical simulations of a structural system consisting of steel perforated thin-walled beams and a steel grating. The simulations were conducted using the finite element method. The analysis took into account physical and geometric nonlinearity as well as the contact between the steel grating and the beams. The main goal of the research was to develop load-bearing curves for the main beam in...
-
Wave Method for Structural Health Monitoring: Testing Using Full-Scale Shake Table Experiment Data
PublicationAn algorithm of the wave method for structural health monitoring (SHM) is tested and calibrated using shake table experiment data of a full-scale, seven-story, reinforced-concrete building slice. The method is based on monitoring changes in the velocity of waves propagating vertically through the structure, identified by least-squares (LSQ) fit of beam models. The experiment was conducted by a team from the University of California,...
-
Influence of reduction process on the structural and mechanical properties of (Pb,Bi)-(Si,Ge)-O oxide glasses
PublicationThe effect of the reduction process in H2 at 380 °C on the microstructure and elemental composition of a glass Bi0.4Pb0.2Si0.4Ox has been investigated. It has been shown that after reduction a clearly separated top layer with a thickness of approx. 50 µm was formed on the surface of the sample. This layer is depleted of oxygen and has higher electrical conductivity than the interior of the glass. It has also been found that some...
-
Robust continuous-time controller design via structural Youla-Kučera parameterization with application to predictive control.
PublicationPraca dotyczy projektowania ciągłoczasowego sterowania liniowymi układami SISO o niepewnych parametrach w celu uzyskania nominalnej i odpornej stabilności oraz nominalnej i odpornej jakości regulacji. Specyficzne zastosowanie koncepcji parametryzacji Youli-Kučery (YK) prowadzi do nowego zastosowania obserwatorowych struktur sterowania. Metoda ta została połączona z nominalną strategią uogólnionego sterowania predykcyjnego CGPC,...
-
Case Study of Old Steel Riveted Railway Truss Bridge: From Material Characterization to Structural Analysis
PublicationThe structural analysis of an old steel riveted railway truss bridge located over the Maruska River on the Działdowo – Olsztyn, Poland railway line is performed in this paper to check its behaviour under today’s railway loads. The mechanical properties of construction steel extracted from the old steel bridge are investigated by tensile tests, impact tests through the Charpy pendulum impact V-notch, and an optical emission spectrometer....
-
Homoleptic mono-, di-, and tetra-iron complexes featuring phosphido ligands: a synthetic, structural, and spectroscopic study
PublicationWe report the first series of homoleptic phosphido iron complexes synthesized by treating either the β-diketiminato complex [(Dippnacnac)FeCl2Li(dme)2] (Dippnacnac = HC[(CMe)N(C6H3-2,6-iPr2)]2) or [FeBr2(thf )2] with an excess of phosphides R2PLi (R = tBu, tBuPh, Cy, iPr). Reaction outcomes depend strongly on the bulkiness of the phosphido ligands. The use of tBu2PLi precursor led to an anionic diiron complex 1 encompassing a planar...
-
Numerical and experimental investigation of guided ultrasonic wave propagation in non-uniform plates with structural phase variations
PublicationThe article presents the results of numerical and experimental investigations of guided wave propagation in aluminum plates with variable thickness. The shapes of plate surfaces have been specially designed and manufactured using a CNC milling machine. The shapes of the plates were defined by sinusoidal functions varying in phase shift, which forced the changes in thickness variability alongside the propagation path. The main aim...
-
Mapping the Structural and Dynamic Determinants of pH-Sensitive Heparin Binding to Granulocyte Macrophage Colony Stimulating Factor
PublicationGranulocyte macrophage colony stimulating factor (GMCSF) is an immunomodulatory cytokine that is harnessed as a therapeutic. GMCSF is known to interact with other clinically important molecules, such as heparin, suggesting that endogenous and administered GMCSF has the potential to modulate orthogonal treatment outcomes. Thus, molecular level characterization of GMCSF and its interactions with biologically active compounds is critical...
-
Synthesis and structural characterization of bio-based bis(cyclic carbonate)s for the preparation of non-isocyanate polyurethanes
PublicationBio-based cyclic carbonates are of significant research interest as monomers for non-isocyanate polyurethane (NIPU) synthesis. This research describes the synthesis of a series of five-membered bis(cyclic carbonate)s using bio-based polyether polyols (PO3G) with different molecular weights (250, 650 and 1000 g mol−1) and carbon dioxide as green feedstocks. The utilization of CO2 as a source of carbon in the chemical reaction is...
-
Evaluating Industry 4.0 Implementation Challenges Using Interpretive Structural Modeling and Fuzzy Analytic Hierarchy Process
PublicationThe fourth industrial revolution known as Industry 4.0 is reshaping and evolving the way industries produce products and individuals live and work therefore, gaining massive attraction from academia, business and politics. The manufacturing industries are optimistic regarding the opportunities Industry 4.0 may offer such as, improved efficiency, productivity and customization. The present research contributes to the Industry 4.0...
-
Structural changes of bacterial cellulose due to incubation in conditions simulating human plasma in the presence of selected pathogens
PublicationBacterial nanocellulose (BNC) is a natural biomaterial with a wide range of medical applications. However, it cannot be used as a biological implant of the circulatory system without checking whether it is biodegradable under human plasma conditions. This work aimed to investigate the BNC biodegradation by selected pathogens under conditions simulating human plasma. The BNC was incubated in simulated biological fluids with or...
-
Influence of microwave treatment conditions of GTR on physico-mechanical and structural properties of NBR/NR/GTR composites
PublicationThe increasing amount of tires used in the industry induces the researchers to find alternatives to the recycling of the end-of-life tires. Several alternatives in order to application of ground tire rubber GTR include their incorporation as a filler in composites. The main issue in this approach is the lack of compatibility between GTR and polymer matrix. In order to solve this problem the devulcanization by microwaves has been...
-
Synthesis, structural characterization, and thermal properties of Ca‐ and La‐doped soda‐lime glasses by laser melting
PublicationLaser melting techniques have been used in the preparation of unconventional glass compositions with high melting temperatures. Thus, we wanted to test the feasibility of using a CO2 laser in the preparation of nitrogen-rich oxynitride glasses and nitride silicate glasses. Melting from oxides and metallic raw materials, we wanted to study first glass formation and possible evaporation losses of the glass components. Two glass series...
-
Mixed ionic-electronic conductivity and structural properties of strontium-borate glass containing nanocrystallites of Bi2 VO5.5
PublicationSamples of strontium borate glass containing bismuth vanadate nanocrystallites were prepared. Nanocomposites containing up to 45mol% of the Bi2VO5.5 phase exhibit electrical properties closer to the strontium-borate glass than to the ferroelectric Bi2VO5.5 ceramic. The glass matrix still may contain some part of bismuth and vanadium ions even after crystallization process and there is too little of crystalline phase to observe...
-
The Perception of an Entrepreneur’s Structural, Relational and Cognitive Social Capital among Young People in Poland - An Exploratory Study
PublicationThe goal of the current paper is to verify how an entrepreneur’s structural, relational and cognitive social capital levels are perceived by young people in Poland. The research involved a group of 374 undergraduate business students from a Polish university as participants. Participants completed a survey on entrepreneurial cognitions. It was found that participants assess the level of an entrepreneur’s social capital as relatively...
-
Cobalt doping of nickel ferrites via sol gel approach: effect of doping on the structural and dielectric properties
Publication -
Light-Induced Transformation of the Aromatic Heptaene Antifungal Antibiotic Candicidin D into Its All-Trans Isomer
PublicationIllumination of the aromatic heptaene macrolide antifungal antibiotic candicicin D with UV light results in an isomerization of the molecule. The product formed after irradiation of the candicidin complex with UV light (λ=365nm), namely, iso-candicidin D, was isolated and subjected to 2D NMR studies, consisting of DQF-COSY, ROESY, TOCSY, HSQC, and HMBC experiments. The obtained spectral data unambiguously evidenced that iso-candicidin...
-
Preventing of earthquake-induced pounding between steel structures by using polymer elements – experimental study
PublicationPounding between two, or more, adjacent buildings during earthquakes has been identified as one of the reasons for substantial damage or even total collapse of colliding structures, so it has been the subject of numerous studies in the recent years. A major reason leading to interactions between adjacent, insufficiently separated structures results from the differences in their dynamic properties. A number of different methods...
-
Deformation Analysis of a Composite Bridge during Proof Loading Using Point Cloud Processing
PublicationRemote sensing in structural diagnostics has recently been gaining attention. These techniques allow the creation of three-dimensional projections of the measured objects, and are relatively easy to use. One of the most popular branches of remote sensing is terrestrial laser scanning. Laser scanners are fast and efficient, gathering up to one million points per second. However, the weakness of terrestrial laser scanning is the...
-
Modified nanodiamond particle size studies by means of dynamic light scattering technique
PublicationThe Methods Utilizing the Phenomena of Light Scattering to Measure Particle Size distribution in different solvent, such as deionise water and alcohol and also to study the various structural formation when nanodiamond solution is placed on silicon surface. The purpose of this research project is divided into two parts to configure the measurement units for examining modified nanodiamond particles, examination...
-
Modified nanodiamond particle size studies by means of dynamic light scattering technique
PublicationThe Methods Utilizing the Phenomena of Light Scattering to Measure Particle Size distribution in different solvent, such as deionise water and alcohol and also to study the various structural formation when nanodiamond solution is placed on silicon surface. The purpose of this research project is divided into two parts to configure the measurement units for examining modified nanodiamond particles, examination...
-
Morphology and conductivity investigations of nickel-molybdenium alloy by means of Scanning Spreading Resistance Microscopy
Open Research DataElectrolytically deposited nickel-molybdenum alloys are interesting materials because of their high corrosion resistance and low over-potential for hydrogen evolution. Despite many studies devoted to the deposition of these alloys, the mechanism of co-deposition is not fully understood [1]. The aim of the research was to preserve the electrochemically...
-
NEW SOLUTIONS FOR THE SOLAR CHARGE CONTROLLERS DESIGN FOR OBTAINING TRUE MPP IN PARTLY SHADED PV MODULES
PublicationSoft shading sources such as tree limbs, structural elements of buildings and chimneys, scatter and refract sunlight, significantly reducing the amount of radiation reaching the surface of the module. The hard shadings located directly on the surface (i.e. bird droppings, leaves, snow) tend to stop sunlight completely. These phenomena significantly affects the output characteristics of photovoltaic modules and often contribute...
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Enhanced photoelectrochemical and photocatalytic performance of iodine-doped titania nanotube arrays
PublicationThe paper discusses the synthesis and performance of iodine doped titania nanotube arrays exhibited under irradiation. The doping procedure was performed as an additional, electrochemical process carried out after formation of nanotube arrays via anodization of Ti substrate. The optical and structural properties were characterized using Raman, UV-vis, photoluminescence and X-ray photoelectron spectroscopy. The surface morphology...
-
Epoxydibenzo[b,f][1,5]diazocines: From a Hidden Structural Motif to an Efficient Solvent-Free Synthetic Protocol
Publication -
Structural modification and band gap engineering of carbon nano-onions via sulphur doping: Theoretical DFT study
Publication -
Structural Change in New Member States (1995–2005): Shift–Share Analysis of Productivity Growth and its Determinants
Publication -
Structural change in New Member States (1995-2005): shift-share analysis of productivity growth and its determinants
PublicationThe chapter focuses on the latest developments in ten New MemberStates (presented vis-à-vis EU-15countries), seen from the perspective of structural change and quality upgrading of their economic structures. In particular, recently released disaggregated labor statistics are used,allowing to analyse the process of labor reallocation and productivitychanges associated with inter-and intra-industrystructural change. Since the mid-1990s...
-
Structural evaluation of percolating, self-healing polyurethane–polycaprolactone blends doped with metallic, ferromagnetic, and modified graphene fillers
PublicationComposites with differently shaped micro- and nanofillers show various, unique thermal, and physicochemical properties when mixed with carefully chosen polymer matrix. Selected composition holds strategic value in achieving desired properties that is biodegradability, thermoelectric conductivity, and shape memory for organic coating. The main aim of this work is to briefly examine structural changes after reaching percolation...
-
Structural and Evolutionary Analysis Indicate That the SARS-CoV-2 Mpro Is a Challenging Target for Small-Molecule Inhibitor Design
Publication -
Magnetic, Structural and Spectroscopic Properties of Iron(II)-Octacyanoniobate(IV) Crystalline Film Obtained by Ion-Exchange Synthesis
Publication -
Structural and Evolutionary Analysis Indicate that the SARS-CoV-2 Mpro is an Inconvenient Target for Small-Molecule Inhibitors Design
Publication -
Processing of point cloud data retrieved from terrestrial laser scanning for structural modeling by Finite Element Method
PublicationFinite Element Method is one most popular contemporary method of strength analysis. The method is an advanced method for solving differential equations, based on discretization, which means that area is divided into finite elements. Each finite element has a solution of the equation approximated by specific functions and performing the actual calculations only for nodes of this division. Finite Element Method is widely used in...
-
Structural changes of a simple peptide—Trpzip-1—in aqueous solutions and the corresponding hydration phenomena under the influence of temperature
PublicationTrpzip-1, a simple β-hairpin, is a rare example of peptide with stable secondary structure and can be a convenient model to study temperature-related processes that potential prion or amyloid proteins undergo. Although its sequence is simple, the exact processes which the peptide undergoes in aqueous solutions are quite complex and not well understood. The selection of well-established experimental (DSC, FTIR) and theoretical methods...
-
Evaluation of structural change during fast transformation process of cross-linked NR into liquid NR by light pyrolysis
PublicationThe presence of cross-linked networks in rubber creates a tremendous problem for recycling and reusing of waste rubber. Fast transformation of cross-linked natural rubber (NR) into liquid natural rubber was carried out by light pyrolysis in temperature range from 240 to 300 °C in variable time (in range: 1–30 min). The transformation efficiency was evaluated by measuring the sol fraction and the cross-link density of the gel fraction....
-
Effect of crystallinity on structural, thermal, and in vitro dissolution properties of Na2O-CaO-Nb2O5/MgO-P2O5 glass-ceramics
PublicationThe impact of the crystallinity on structural, thermal, and in vitro dissolution properties were examined for Na2O- CaO-Nb2O5/MgO-P2O5 glasses/glass-ceramics. Glass-ceramics were synthesized via a spontaneous crystallization process. The Nb content in the materials increased with melting temperature, furthermore, the crystallinity is proportional to the Nb content. The presence of crystalline niobates and phosphates is confirmed...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublicationThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Rozwój technologii nanokrystalizacji warstwy wierzchniej materiałów konstrukcyjnych = Development of nanocrystallization technologies of the surface layer of structural materials
PublicationPrzedstawiono szereg metod modyfikacji warstwy wierzchniej prowadzących do wytworzenia struktur nanokrystalicznych. Wskazano na zalety, wady i kierunki rozwoju poszczególnych metod
-
Evaluation of structural and electrical properties of multicomponent spinel oxide thin films deposited via spray pyrolysis technique
PublicationThis work reports the preparation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited layers were amorphous, and crystallised upon heat treatment at 500 ◦C. Microstructural analyses proved a homogeneous...
-
Thermal performance of building envelopes with structural layers of the same density: Lightweight aggregate concrete versus foamed concrete
Publication -
Analytical expression between the impact damping ratio and the coefficient of restitution in the non-linear viscoelastic model of structural pounding
PublicationWyniki wcześniejszych badań pokazują, iż nieliniowy model lepko-sprężysty zderzeń konstrukcji budowlanych podczas trzęsień ziemi najdokładniej symuluje siłę zderzenia w czasie kontaktu oraz odpowiedź konstrukcji. Celem niniejszego artykułu jest wyprowadzenie wzoru na zależność pomiędzy liczbą tłumienia zderzenia (parametr wspomnianego modelu) a współczynnikiem odbicia, który jest parametrem często stosowanym i analizowanym w literaturze....
-
Structural Changes and Their Implications in Foamed Flexible Polyurethane Composites Filled with Rapeseed Oil-Treated Ground Tire Rubber
PublicationThe utilization of post-consumer car tires is an essential issue from an ecological andeconomic point of view. One of the simplest and the least harmful methods is their material recyclingresulting in ground tire rubber (GTR), which can be further applied as fillers for polymer-basedcomposites. Nevertheless, insufficient interfacial interactions implicate the necessity of GTR modi-fication before introduction into polymer matrices....
-
Structural evaluation of percolating, self-healing polyurethane–polycaprolactone blends doped with metallic, ferromagnetic, and modified graphene fillers
PublicationComposites with differently shaped micro- and nanofillers show various, unique thermal, and physicochemical properties when mixed with carefully chosen polymer matrix. Selected composition holds strategic value in achieving desired properties that is biodegradability, thermoelectric conductivity, and shape memory for organic coating. The main aim of this work is to briefly examine structural changes after reaching percolation threshold...
-
Two-step Conversion of Crude Glycerol Generated by Biodiesel Production into Biopolyols: Synthesis, Structural and Physical Chemical Characterization
PublicationIn this work biopolyols were synthesized via two-step process from crude glycerol and castor oil. For better evaluation of analyzed process, the impact of its time and temperature on the structure and properties of biopolyols was determined. Obtained results fully justified conducting of synthesis in two steps. Prepared materials were characterized by hydroxyl value and water content comparable to polyols industrially applied in...
-
Nonlinear finite element modeling of vibration control of plane rod-type structural members with integrated piezoelectric patches
PublicationThis paper addresses modeling and finite element analysis of the transient large-amplitude vibration response of thin rod-type structures (e.g., plane curved beams, arches, ring shells) and its control by integrated piezoelectric layers. A geometrically nonlinear finite beam element for the analysis of piezolaminated structures is developed that is based on the Bernoulli hypothesis and the assumptions of small strains and finite...
-
DEM analysis of micro-structural events within granular shear zones under passive earth pressure conditions
PublicationW artykule omówiono wyniki obliczeń numerycznych dla pasku dla stanu pasywnego sztywnej ścianki podczas jej translacji stosując metodę elementów dyskretnych. Analizowano głównie zjawiska mikrostrukturalne w strefach ścinania podczas translacji sztywnej ścianki. Szczególna uwagę zwrócono na pojawienie się wirów w materiale granulowanym.
-
The influence of transition metals (Fe, Co) on the structural, magnetic and optical properties of TiO2 nanoparticles synthesized by the hydrothermal method
Publication -
Investigation on structural, optical and anti-bacterial properties of organic additives iron oxide prepared by chemical route method
Publication -
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
Journals