displaying 1000 best results Help
Search results for: non-anechoic measurements
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublicationHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Determining the conditions for temperature measurements during flat lapping
PublicationPrzedstawiono pomiary temperatury układu wykonawczego docierarki jednotarczowej ABRALAP 380. Badano wpływ liczby stosowanych pierścieni prowadzących przy docieraniu elementów ceramicznych mikroziarnami węglika krzemu. Analizowano przyrost temperatury układu w czasie do trzech godzin. W badaniach zastosowano kamerę termowizyjną V-20II firmy VIGO System S.A.
-
Capacitively coupled ECG measurements - a CMRR circuit improvement
PublicationA typical galvanic-connected electrocardiogram (ECG) measurement system utilizes two signal’s electrodes and a third one in driven-right-leg (DRL) circuit for improving a common-mode rejection ratio(CMRR) of the acquisition system. In capacitive-coupled ECG similar techniques are used, however it is expected, that the utilized DRL subsystem is formed using a capacitive coupling approach, too. An improvement of the acquisition system...
-
Diagnostics of induction motors by means of current supplying measurements
PublicationSkładowe prądu zasilającego silnik, które związane są z uszkodzeniami łożysk są małe w porównaniu z dominującą składową sieciową. Zaproponowano układ pomiarowy do ich pomiaru i przedstawiono wyniki badań diagnostycznych na obiektach rzeczywistych.
-
On measurements applied in scientific researches of microwave heating processes
PublicationPrzedstawiono trudności techniczne wykonywania pomiarów w systemach gdzie stosuje się duże poziomy mocy mikrofalowej. Omówiono zasadę pracy do badania procesu grzania mikrofalowego oraz wybrane problemy występujące przy realizacji takiego systemu. Uzasadniono celowość prowadzenia przedstawionych rodzajów pomiarów w badaniach procesów grzania mikrofalowego materiałów.
-
On accurracy of polarization resistance estimation by electrochemical noise measurements
PublicationPrzedstawiono sposób estymacji rezystancji polaryzacji, wykorzystywanej do oceny szybkości procesów korozji. Zaproponowano formułę określającą błąd losowy estymacji rezystancji polaryzacji. Przytoczono i przedyskutowano eksperymentalne wyniki estymacji rezystancji polaryzacji na podstawie pomiarów szumów elektrochemicznych w układzie trzech elektrod pomiarowych.
-
Electron diffision coefficients in triatomic gases measurements and model
PublicationPraca zawiera porównanie współczynników dyfuzji elektronów w gazach trójatomowych (N2O, C2O) zmierzonych w doświadczeniu ze współczynnikami wyznaczonymi numerycznie z wykorzystaniem równania Boltzmanna oraz z zastosowaniem metody Monte Carlo. Przedstawiona procedura pozwala zweryfikować przekroje czynne na zderzenia elektronów z drobinami gazów.
-
Targed tracking with adaptive fusionof multiple sensor measurements.
PublicationW pracy przedstawiono metodę adaptacyjnej selekcji pomiarów z wielu radarów wykorzystywanych w procesie integracji pomiarów dla śledzenia obserwowanego obiektu. W przypadku dużego zróżnicowania dokładności pomiarów pochodzących z różnych radarów, rezultaty integracji pomiarów nie różnią się znacząco od wyników śledzenia opartego na pomiarach z najbardziej dokładnego źródła.
-
Digital measurements of the feedback signals for observing behaviour of a drive.
PublicationW pracy omówiono sposoby badań przebiegu ruchu realizowanego przez napęd, w tym poprzez pomiar sygnałów sprzężeń zwrotnych. Przedstawiono różne typy błędów pomiaru sygnałów sprzężeń zwrotnych i ich oddziaływanie na wyniki.
-
Impedance measurements of skin layered structure for burns determination.
PublicationW pracy analizowany jest dwuwarstwowy model skóry. Pokazano, że za pomocą wielokrotnych pomiarów immitancyjnych jest możliwe wyznaczenia zarówno parametrów elektrycznych oparzonej skóry jak i geometrycznych. Przedstawiono algorytm estymacji i procedurę pomiarową wyżej wymienionych parametrów.
-
Experimental measurements of the hydrodynamic characteristics of the pod propulsor models
PublicationPraca przedstawia wyniki pomiarów charakterystyk hydrodymicznych trzech wariantów modelu pędnika azymutalnego. Charakterystyki obejmują napór pędnika, siłę boczną i moment względem osi pionowej w zależności od współczynnika posuwu i kąta dryfu.
-
On the use of a charge balancing method for low energy measurements
PublicationThe paper presents the method for the estimation of the energy consumption of the low-power microcontroller-based devices. Due to high dynamics of the changes of the supply current of the tested devices during the operational cycle, the consumed energy estimation is not easy. In order to avoid disadvantages of known methods, the charge balancing method was employed similarly like in some types of A/D converters.
-
Comment on "Measurements without probabilities in the final state proposal"
PublicationThe final state proposal [G.T. Horowitz and J.M. Maldacena, J. High Energy Phys.2004(2),8 (2004)] is an attempt to relax the apparent tension betweenstring theory and semiclassicalarguments regarding the unitarity of black hole evaporation. The authors of [R. Bousso and D.Stanford, Phys. Rev. D89, 044038 (2014)] analyze thought experiments where an infalling observerfirst verifies the entanglement between early and late Hawking...
-
Typology of low developed non-metropolitan sub-regions in the European Union
PublicationThis paper shows a typology of 319 NUTS-3 sub-regions in the European Union. The selected sub-regions are non-metropolitan sub-regions, whose gross domestic product per capita in 2011 was below 75% of the EU average. The objective of this typology was to recognize diversity in the examined sub-regions as a starting point for the selection of areas for future comparative research. The typology takes into account 24 variables related...
-
On modelling and non-linear elasto-plastic analysis of thin shells with deformable junctions
PublicationThe undeformed base surface of the irregular thin shell is modelled by the union of a finite number of regular smooth surface elements joined together along spatial curvilinear surface edges. The equilibrium conditions are formulated by postulating an appropriate form of the principle of virtual work, where also deformability of shell junctions is taken into account. The PVW is then discretised by C1 finite elements and the incremental-iterative...
-
Sensitivity analysis based on non-intrusive regression-based polynomial chaos expansion for surgical mesh modelling
PublicationThe modelling of a system containing implants used in ventral hernia repair and human tissue suffers from many uncertainties. Thus, a probabilistic approach is needed. The goal of this study is to define an efficient numerical method to solve non-linear biomechanical models supporting the surgeon in decisions about ventral hernia repair. The model parameters are subject to substantial variability owing to, e.g., abdominal wall...
-
Non-isolated resonant quasi-Z-source network DC–DC converter
PublicationA novel non-isolated resonant quasi-impedance (quasi-Z)-source network DC–DC converter is proposed. The resonant impedance source network is derived from the quasi-Z-source network by including the autotransformer-based resonant cell instead of the second inductor of the quasi-Z-network. The leakage inductance of the autotransformer and two resonant capacitors connected in series with the autotransformer windings constitute a high-frequency...
-
Excitation of Non-Wave Modes by Sound of Arbitrary Frequency in a Chemically Reacting Gas
PublicationThe nonlinear phenomena in the field of high intensity sound propagating in a gas with a chemical reaction, are considered. A chemical reaction of A → B type is followed by dispersion and attenuation of sound which may be atypical during irreversible thermodynamic processes under some conditions. The first and second order derivatives of heat produced in the chemical reaction evaluated at the equilibrium temperature, density and...
-
Seeding enhancement for microcrystaline diamond layers growth on non-diamond substrates
PublicationThe present paper gives an overview on the possible methods of seeding substrates for diamond layers growth. Diamond in reason of his properties is very desirable material in microelectronic, biomedical and waste treatment sensors. Microcrystalline diamond for these applications must be grown on silicon substrate in microwave plasma assisted chemical vapor deposition (MPACVD). To grow diamond on non-diamond surface pre-growth...
-
Accuracy of a low-cost autonomous hexacopter platforms navigation module for a photogrammetric and environmental measurements
PublicationA photogrammetry and environmental measurements from an unmanned aerial vehicle (UAV) are a low-cost alternative for a traditional aerial photogrammetry. A commercial off-the-shelf products (COTS) offers a variety of cheap components that a suitable to be used on board a UAV. In this paper a low-cost navigation module based on Ublox NEO-M8N GPS and Pixhawk flight controller have been described, as a main extrinsic parameters source...
-
APPLICATION OF INFRARED THERMOGRAPHY TO NON-CONTACT TESTING OF AD/DC POWER SUPPLY
PublicationTesting of AC/DC power supplies using the thermography was carried out in order to assess their assembly and operation correctness before launching them on the market. The investigation was carried out for 17 AC/DC power supplies which passed the standard tests (measurements of their basic parameters and characteristics). The investigation consisted of two steps. In the first step the dispersion of temperature on power supply boards...
-
The results of the nitrogen adsorption/desorption measurements of CPMD and CPMH
Open Research DataThe results of the nitrogen adsorption/desorption measurements of CPMD and CPMH. The adsorption/desorption isothermswere carried out at 77 K using a Quantachrome Autosorb-1C-MS instrument. Sample abbreviations (CPMD, CPMH) are in agreement with the markings used in the linked publication.
-
Results of electrical voltage measurements in reactors - part 1
Open Research DataResults of electric voltage measurements in six reactors using various plantings. These are the results of the project: Integrated approach 3M (Macrophytes-Microbiome-Modelling) to elucidate mechanisms of bioenergy production and micropollutants transformation in Floating Treatment Wetlands combined with Microbial Fuel Cells.
-
Non-ergodic fragmentation upon collision-induced activation of cysteine–water cluster cations
PublicationCysteine–water cluster cations Cys(H2O)3,6 + and Cys(H2O)3,6H+ are assembled in He droplets and probed by tandem mass spectrometry with collision-induced activation. Benchmark experimental data for this biologically important system are complemented with theory to elucidate the details of the collisioninduced activation process. Experimental energy thresholds for successive release of water are compared to water dissociation energies...
-
Non-enzymatic flexible glucose sensing platform based on nanostructured TiO2–Au composite
PublicationAll over the world the number of people suffering from diabetes and related complications is drastically growing. Therefore, the need for accurate, reliable and stable sensor for monitoring of glucose in human body fluids is becoming highly desirable. In this work we show that material composed of gold layers deposited onto TiO2 nanotubes (NTs) formed onto the flexible Ti foil exhibits great response toward glucose oxidation and...
-
Application of adjusted subpixel method (ASM) in HRCT measurements of the bronchi in bronchial asthma patients and healthy individuals
PublicationBackground: Recently, we described a model system which included corrections of high-resolution computedtomography (HRCT) bronchial measurements based on the adjusted subpixel method (ASM).Objective: To verify the clinical application of ASM by comparing bronchial measurements obtained bymeans of the traditional eye-driven method, subpixel method alone and ASM in a group comprised ofbronchial asthma patients and healthy individuals.Methods:...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Stationary underwater channel experiment: Acoustic measurements and characteristics in the Bornholm area for model validations
PublicationThe underwater acoustical channel is time-variant, and even on small time scales there is often existing no ‘acoustical frozen ocean’. Popular is the use of WSSUS-channel transmission modeling (Wide-Sense Stationary Uncorrelated Scattering) for the stochastic description of bandpass signals in GSM mobile phones with moving participants; since this results in a halved number of model parameters. For underwater sound applications...
-
Tyre/road noise of passenger car tyres, including tyres for electric vehicles - road measurements
PublicationThe paper presents the results from CPX measurements of tyre/road noise performed for selected passenger car tyres, including the tyres especially designed for electric vehicles. The tyres have been measured when rolling on several typical road surfaces in Norway and in Poland. In addition, the tyres have been measured on some very low noise road surfaces, such as a the poroelastic road surface (PERS). The measurement results...
-
Induction Generator with Direct Control and a Limited Number of Measurements on the Side of the Converter Connected to the Power Grid
PublicationThe article presents an induction generator connected to the power grid using the AC/DC/AC converter and LCL coupling filter. Three-level inverters were used in the converter, both from the generator side and the power grid side. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field-Oriented Control (DFOC) method. At...
-
Decomposition of Acoustic and Entropy Modes in a Non-Isothermal Gas Affected by a Mass Force
PublicationDiagnostics and decomposition of atmospheric disturbances in a planar flow are considered in this work. The study examines a situation in which the stationary equilibrium temperature of a gas may depend on the vertical coordinate due to external forces. The relations connecting perturbations are analytically established. These perturbations specify acoustic and entropy modes in an arbitrary stratified gas affected by a constant...
-
Comparison of buckling resistance of columns modelled by beam and shell elements using non-linear analysis
PublicationThe aim of the paper is to investigate the stability process in the axially compressed columns modelled by beam and shell elements using static and dynamic finite element analysis by taking both the geometric and material non-linearity into account. The perfect columns and columns with geometric imperfections were analysed. The differences between the results of static and dynamic analyses in shell and beam models were discussed.
-
XPS measurements of the iron elements covered by chromium
Open Research DataAnticorrosive coatings are an important issue in modern materials engineering. One of the most commonly used, for that coating materials, is chrome. Three metal elements were measured, named as Turcja, WB Tech and Nomet. Names were given according to producer of elements. XPS measurements of the Cr 2p region give an ansver concering on surface chemical...
-
Instantaneous power signal measurements for bearing diagnostics
Open Research DataBearing diagnostics can be carried out based on the method, which relies on the measurement and analysis of the variability of the signal instantaneous power, defined as the product of instantaneous current and voltage power supplied to the engines. Bearing damage causes the appearance of deformations, which are in the form of additional harmonic components...
-
Regression points in non-intrusive polynomial chaos expansion method and D-optimal design
PublicationThe paper addresses selected issues of uncertainty quantification in the modelling of a system containing surgical mesh used in ventral hernia repair. Uncertainties in the models occur e.g. due to variability of abdominal wall properties among others. In order to include them, a non-intrusive regression-based polynomial chaos expansion method is employed. Its accuracy depends on the choice of regression points. In the study a relation...
-
Testing the Positioning Accuracy of GNSS Solutions during the Tramway Track Mobile Satellite Measurements in Diverse Urban Signal Reception Conditions
PublicationMobile Global Navigation Satellite System (GNSS) measurements carried out on the railway consist of using satellite navigation systems to determine the track geometry of a moving railway vehicle on a given route. Their purposes include diagnostics, stocktaking, and design work in railways. The greatest advantage of this method is the ability to perform measurements in a unified and coherent spatial reference system, which...
-
Zdzisław Kowalczuk prof. dr hab. inż.
PeopleZdzislaw Kowalczuk received his M.Sc. degree in 1978 and Ph.D. degree in 1986, both in Automatic Control from Technical University of Gdańsk (TUG), Gdańsk, Poland. In 1993 he received his D.Sc. degree (Dr Habilitus) in Automatic Control from Silesian Technical University, Gliwice, Poland, and the title of Professor from the President of Poland in 2003. Since 1978 he has been with Faculty of Electronics, Telecommunications and Informatics...
-
An observability and detectability analysis for non-linear uncertain CSTR model of biochemical processes
PublicationThe problem of proving observability/detectability properties for selected non-linear uncertain model of biochemical processes has been addressed in this paper. In particular, the analysis of observability/detectability in the face of parametric and unstructured uncertainty in system dynamics transformed into unknown inputs, and unknown initial conditions has been performed. Various sets of system measured outputs were taken into...
-
Measurements of no-load and short-circuit parameters of power transformers with taps
Open Research Data1) The Laboratory LINTE^2 is a large research infrastructure operated by the Faculty of Electrical and Control Engineering at Gdańsk University of Technology, to be found in Gdańsk, Poland (54.3690 N, 18.6130 E).
-
Bio‑derived polyurethanes obtained by non‑isocyanate route using polyol‑based bis(cyclic carbonate)s—studies on thermal decomposition behavior
PublicationNon-isocyanate polyurethanes (NIPUs) constitute one of the most prospective groups of eco-friendly materials based on their phosgene-free synthesis pathway. Moreover, one of the steps of their obtaining includes the use of carbon dioxide (CO 2 ), which allows for the promotion of the development of carbon dioxide capture and storage technologies. In this work, non- isocyanate polyurethanes were obtained via three-step synthesis...
-
Computer-aided analysis of signals from a low-coherence Fabry-Perot interferometer used for measurements of biological samples
PublicationThe aim of the study was to develop an automated computer-aided system for analysis of spectrograms obtained from measurements of biological samples performed with a low-coherence Fabry-Pérot interferometer. Information necessary to determine dispersion characteristics of measured materials can be calculated from the positions of the maxima and minima that are present in their spectra. The main challenge faced during the development...
-
Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ
Open Research DataThis dataset contains results of the research on the basis of which the Figures presented in the manuscript entitled "Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ on structural, electrical, and electrochemical properties for potential oxygen electrode of intermediate temperature Solid Oxide Cells" were prepared. A detailed description...
-
NON-STATIONARY THERMAL SELF-ACTION OF ACOUSTIC BEAMS CONTAINING SHOCK FRONTS IN THERMOCONDUCTING FLUID
PublicationNon-stationary thermal self-action of a periodic or impulse acoustic beam containing shock fronts in a thermoconducting Newtonian fluid is studied. Self-focusing of a saw-tooth periodic and impulse sound is considered, as well as that of a solitary shock wave which propagates with the linear sound speed. The governing equations of the beam radius are derived. Numerical simulations reveal that the thermal conductivity weakens the...
-
Linear game non-contextuality and Bell inequalities—a graph-theoretic approach
PublicationWe study the classical and quantum values of a class of one-and two-party unique games, that generalizes the well-known XOR games to the case of non-binary outcomes. In the bipartite case the generalized XOR(XOR-d) games we study are a subclass of the well-known linear games. We introduce a 'constraint graph' associated to such a game, with the constraints defining the game represented by an edge-coloring of the graph. We use the...
-
Modeling the impact of rotor movement on non-linearity of motor currents waveforms in high-speed PMSM drives
PublicationMotor current measurement techniques as well as predictive control algorithms for electric drives rely on an assumption of linear motor currents changes resulting from constant inverter output voltages. Recent research has reported that this assumption does not hold in motors with short electrical time constant, and in drives whose rotor position advances substantially during a control period. This paper proposes a simulation model...
-
Evaluation of the Possibility of Identifying a Complex Polygonal Tram Track Layout Using Multiple Satellite Measurements
PublicationWe present the main assumptions about the algorithmization of the analysis of measurement data recorded in mobile satellite measurements. The research team from the Gda´nsk University of Technology and the Maritime University in Gdynia, as part of a research project conducted in cooperation with PKP PLK (Polish Railway Infrastructure Manager), developed algorithms supporting the identification and assessment of track axis layout....
-
Evaluation of the Possibility of Identifying a Complex Polygonal Tram Track Layout Using Multiple Satellite Measurements
PublicationWe present the main assumptions about the algorithmization of the analysis of measurement data recorded in mobile satellite measurements. The research team from the Gda´nsk University of Technology and the Maritime University in Gdynia, as part of a research project conducted in cooperation with PKP PLK (Polish Railway Infrastructure Manager), developed algorithms supporting the identification and assessment of track axis layout....
-
Isolation of the relative decrease in magnetic permeability contribution to reluctance of an open magnetic circuit based on stray field measurements
PublicationThe goal of the study was to evaluate a relative decrease in magnetic permeability in open magnetic circuits based on stray magnetic field measurements. The boundary element method was used to simulate magnetic circuits with variable geometry and variable magnetic permeability. The simulated magnetic circuits were rectangular or bone-shaped flat samples. Reluctance was increased in the middle of the samples resulting in leakage...
-
New Method of Non-Linear Electrochemical Impedance Spectroscopy with an Amplitude-Modulated Perturbation Signal
PublicationThe paper presents a new method of non-linear electrochemical impedance spectroscopy (NLEIS), which allows fast and nondestructive evaluation of the corrosion rate and determination of the Tafel coefficients values for a corrosion system under investigation. This method employs amplitude modulation of the ac perturbation signal. The study demonstrated that it was possible to obtain impedance characteristic as a function of the...
-
Enriching the Context: Methods of Improving the Non-contextual Assessment of Sentence Credibility
PublicationThis paper presents several methods of automatic context enrichment of sentences that need to be evaluated, tagged or fact-checked by human judges. We have created a corpus of medical Web articles. Sentences from this corpus have been fact-checked by medical experts in two modes: contextually (reading the entire article and evaluating sentence by sentence) and without context (evaluating sentences from all articles in random order)....