Search
Filters
total: 529
filtered: 400
Search results for: COAMPS
-
Designing drainage systems – possible application of advanced calculations and hydrodynamical modeling
PublicationNowadays we can observe a faster development of drainage systems than ever. This gives us an opportunity to de- sign more efficient systems that can cope with the rapid growth of cities and, what comes with it, impervious surfaces. Here the question arises, whether traditional methods used in drainage system design are potent enough to cope with the emerging prob- lems and difficulties. In this paper we will make...
-
Generalized access control in hierarchical computer network
PublicationThe paper presents the design of the security layer for a distributed system located in the multizone hierarchical computer network. Depending on the zone from which a client’s request comes to the system and the type of the request, it will be either authorized or rejected. There is one common layer for the access to all the business services and interactions between them. Unlike the commonly used RBAC model, this system enforces...
-
A study of a reduction of a micro- and nanometric bismuth oxide in hydrogen atmosphere
PublicationA reduction of bismuth oxide in hydrogen atmosphere was investigated. The reaction was performed with a material in various structural forms: powder: with micrometric grains, powder with nanometric grains and powder pressed into pellets. The process was performed in both isothermal and non-isothermal conditions. An activation energy of the reaction calculated with Friedman method was found to be about 85 kJ/mol for the reduction...
-
Complex Predictive Solution for Computerized Processes in Tire Industry
PublicationFollowing increasing market needs of productivity, cost reduction and safety requirements, computerized industry are faced to finding optimum between economic aspects of business and safety-related risk management. Modern factories equipped with computerized processes and extended diagnostic tools to support operator do not often use of all information’s which comes from the equipment. Some of the relations between the events are...
-
THE IMPACT OF GROUND TIRE RUBBER TREATMENT ON THE THERMAL CONDUCTIVITY OF FLEXIBLE POLYURETHANE/GROUND TIRE RUBBER COMPOSITES
PublicationWaste car tires are burdensome waste, and their utilization is crucial for the natural environment. In many countries, the primary method of their recycling is energy recovery, performed by simple combustion. However, material recycling is much more effective and significantly more beneficial for the natural environment. It results in the generation of ground tire rubber, which can be used to produce polymerrubber composites. It...
-
E-Estonia as a role model? Some general considerations and applicability in France
PublicationEstonia has recently been widely recognised – in the policy circles, academia, as well as the media space – as one of the more advanced nation states when it comes to digital government (and governance) transformation (e.g. Margetts and Naumann, 2017; Heller, 2017). Ever greater attention Estonia attracted with the two most recent digital government initiatives, namely the e-Residency and the virtual data embassy, both first of...
-
What is in a name: Defining “high entropy” oxides
PublicationABSTRACT High entropy oxides are emerging as an exciting new avenue to design highly tailored functional behaviors that have no traditional counterparts. Study and application of these materials are bringing together scientists and engineers from physics, chemistry, and materials science. The diversity of each of these disciplines comes with perspectives and jargon that may be confusing to those outside of the individual fields,...
-
Study on transmission quality in cellular 4G and 5G networks between 2019–2021: Impact of the COVID-19 pandemic on the level of provided services by operating base transceiver stations
PublicationThe COVID-19 pandemic has significantly limited user mobility, not least among students. Remote learning had a particular impact on resource allocation in relation to using terrestrial cellular networks, especially 4G systems in urban agglomerations. This paper presents the results of a quality evaluation of an outdoor environment, carried out between 2019 and 2021 on the campus of a technical university. Annual studies are conducted...
-
Properties of Barium Cerate-Zirconate Thin Films
PublicationIn this work, we review several experimental results showing the electrical properties of barium cerate-zirconate thin films and discuss them in view of the possible influence of various factors on their properties. Most of the presented Ba(Ce, Zr, Y)O3 thin films were formed by the pulsed laser deposition (PLD) technique, however thin films prepared using other methods, like RF magnetron sputtering, electron-beam deposition, powder...
-
Wpływ polietylenu szczepionego bezwodnikiem maleinowym oraz sił ścinających na właściwości mieszanin polietylen wysokiej gęstości-miał gumowy
PublicationScharakteryzowano wpływ kompatybilizatora w postaci polietylenu szczepionego bezwodnikiem maleinowym na właściwości mieszanin PE-HD–miał gumowy. Kompozycje termoplastyczne zawierające 50 cz. mas. rozdrobnionych odpadów gumowych, otrzymano przy użyciu współbieżnej wytłaczarki dwuślimakowej. Poziom sił ścinających generowanych podczas mieszania, regulowano za pomocą zmian prędkości obrotowych ślimaków. Przeprowadzono charakterystykę...
-
Greening Higher Education in Europe. Institutional Transitions to Sustainable Development
PublicationThis book provides a comprehensive overview of the advances made in European higher education institutions (HEIs) over the last twenty years in response to the challenges of sustainable development. In recent years, there has been a visible shift toward sustainable development, and universities have been addressing their accountability to the public through corporate social responsibility. Greening Higher Education in Europe explores...
-
Performance Comparison of a 650 V GaN SSFET and CoolMOS
PublicationThe new technology of wide band gap semiconductors is said to outperform up-to-date silicon devices. High voltage Gallium Nitride (GaN) transistors, now emerging in the market, have even three times shorter switching times and even four times smaller energy losses compared to the best in-class Si devices. In this paper the performance of a 650 V GaN SSFET is evaluated and compared with the newest silicon family of CoolMOS™ technology....
-
Effects of artificial lighting on bioactivity of sweet red pepper (Capsicum annuum L.)
PublicationRecent studies have shown that artificial light effectively promotes the growth and development of red peppers when light spectra, intensities and duration are controlled. Cited reports deal mostly with studies involving with the growth stages of pepper. Changes in the biochemical status of plants were not studied. Therefore, this study focuses on the changes in the content of some bioactive compounds (polyphenols, flavonoids,...
-
3D porous graphene-based structures- synthesis and applications
PublicationPorous carbon-based materials are of the great industrial and academic interest due to their high surface area, low density, good electrical conductivity, chemical inertness and low cost of fabrication. Up to now, the main approach to obtain porous carbon structures has involved the pyrolysis of carbonaceous natural or synthetic precursors. After the isolation of graphene, the interest in 3D porous graphene-based structures (called...
-
Lamp of adjustable spectrum for photographic usage
PublicationPhotography is a unique rapidly growing interdisciplinary field encompassing aspects of science, art and technology. Expectations of photographers are steadily increasing with the development of technology. One of the areas playing a crucial role in photography is lighting. Consequently, several types of light sources for photographic use have been developed. The ongoing research in this field concentrates on lamps with tunable...
-
Selective monitoring of noise emitted by vehicles involved in road traffic
PublicationAn acoustic intensity probe was developed measures the sound intensity in three orthogonal directions, making possible to calculate the azimuth and elevation angles, describing the sound source position. The acoustic sensor is made in the form of a cube with a side of 10 mm, on the inner surfaces of which the digital MEMS microphones are mounted. The algorithm works in two stages. The first stage is based on the analysis of sound...
-
Enzymatic activities behind degradation of glucosinolates
PublicationMyrosinase (thioglucosidase, EC 3.2.1.147) is the enzyme responsible for the hydrolysis of glucosinolates (GLs). In plant tissue, myrosinase and GLs are sequestered in separate cellular compartments. As a result of cell disruption, e.g., after pathogen attack or on chopping or grinding during food preparation, the myrosinase comes into contact with GLs and catalyzes the hydrolysis of thioglucosidic bond in GL structure. Consequently,...
-
Laser-Assisted Synthesis and Oxygen Generation of Nickel Nanoparticles
PublicationNowadays, more than ever, environmental awareness is being taken into account when it comes to the design of novel materials. Herein, the pathway to the creation of a colloid of spherical, almost purely metallic nickel nanoparticles (NPs) through pulsed laser ablation in ethanol is presented. A complex description of the colloid is provided through UV-vis spectroscopy and dynamic light scattering analysis, ensuring insight into...
-
Con l’introduzione
PublicationNata nel 1953 con l’obiettivo di portare l’Italia tra le nazioni avanzate anche in campo energetico, Eni rappresenta una delle principali imprese ad aver influenzato l’innovazione economica del Paese. La sua storia, legata a doppio filo alla figura di Enrico Mattei, consente di seguirne le traiettorie di sviluppo e le strategie di internazionalizzazione, nel quadro di un contesto in continua evoluzione. Questo volume ripercorre...
-
Computational simulation of motion of a rescue module during its launching from ship at rough sea
PublicationThis paper is a continuation of the work titled : “A comp utational model for simulation of motion of rescue module during its launching from stern ramp of a ship at rough sea”. It presents results of computer simulations of motion of a rescue module with embarked persons during its launching on rollers along stern ramp of a ship at rough sea. The simulations were conducted for a selected ship fitted with a launching ramp , for...
-
A grey box model of glucose fermentation and syntrophic oxidation in microbial fuel cells
PublicationIn this work, the fermentative and oxidative processes taking place in a microbial fuel cell (MFC) fed with glucose were studied and modeled. The model accounting for the bioelectrochemical processes was based on ordinary, Monod-type differential equations. The model parameters were estimated using experimental results obtained from three H-type MFCs operated at open or closed circuits and fed with glucose or ethanol. The experimental...
-
COMBINING FUNCTIONAL AND AESTHETIC ASPECTS OF DAYLIGHTING IN SUSTAINABLE ARCHITECTURE WITH THE USE OF DIGITAL DESIGN METHODS
PublicationThe aesthetics of modern architecture should relate to its origins and goals - the environment, function, sustainability and its users. One of the conditions that meet the criteria is the presence of daylight and the use of its potential. The contemporary digital tools that support the design process allow to controlling the use of difficult and capricious materials, such as daylight. They also combine daylighting aspects with...
-
Application of short-time GNSS solution geodynamical studies
PublicationThe paper presents the results of research related to the application of GNSS solutions in short observational periods in geodynamical investigations. Authors used the 3-hour solution appointed from hour-long interval of about 30 chosen stations on mountainous terrains from over 100 which were worked out. The main aim was to check the correctness of such solutions by the comparison with the daily ones. Some outliers in East component...
-
Wpływ struktur wsparcia na efektywność nauczania języka pisanego w środowisku e-learningowym
PublicationThe process of knowledge and language skills development during an online course can be very effective if student engagement in learning is achieved. This can be attained by introducing general and specific support mechanisms prior to the commencement of the course and during it. The former relates to the technological aspect, that is to familiarizing students with the functionalities of the virtual learning environment they will...
-
Influence of compaction effectiveness on interlayer bonding of asphalt layers
PublicationThe paper presents the results of research on the interlayer bonding of asphalt layers compacted in the laboratory and in the field. To measure the interlayer bonding at a temperature of 20°C the Leutner test apparatus was used and load was applied at a rate of 50 mm/minute. Three types of interlayer interfaces were tested: no tack coat and tack coats made of two types of the pure bitumen emulsions. Four compaction techniques were...
-
Mathemathical model of radial passive magnetic bearing
PublicationIn the article mathematical radial model of passive magnetic bearings to ocean engineering units has been presented. The units application in underwater thrusters should increase propulsion systems durability and gives lower maintenance costs. The rotor of electric motor is hanging in magnetic field taken from radial passive magnetic bearings. However axial direction maintenance must be controlled with electromagnets and their...
-
Intracranial electrophysiological recordings from the human brain during memory tasks with pupillometry
PublicationData comprise intracranial EEG (iEEG) brain activity represented by stereo EEG (sEEG) signals, recorded from over 100 electrode channels implanted in any one patient across various brain regions. The iEEG signals were recorded in epilepsy patients (N=10) undergoing invasive monitoring and localization of seizures when they were performing a battery of four memory tasks lasting approx. 1 hour in total. Gaze tracking on the task...
-
Identification of the Agile Mindset and Its Comparison to the Competencies of Selected Agile Roles
PublicationIn this paper we present the results of the identification and evalua-tion of the elements of an agile mindset as well as its comparison to the compe-tence models for the roles of Scrum Master, Product Owner and agile analyst. We have identified 70 unique agile mindset elements from literature and 5 in-terviews with experts. Based on an opinion survey among 52 agile practitioners we evaluated the importance of 26 selected elements...
-
Integration of Multi-Source Geospatial Data from GNSS Receivers, Terrestrial Laser Scanners, and Unmanned Aerial Vehicles
PublicationThe analysis based on geospatial data from different measurement systems now constitutes a complex numerical and practical enterprise. The dynamic development of modern technologies enables rapid and precise acquisition of such data. Nonetheless, the diversity of reference systems is today one of the main challenges for their correct interpretation. The combined use of the processed measurement results and archival data in paper...
-
FPGA Based Real Time Simulations of the Face Milling Process
PublicationThe article presents a successful implementation of the milling process simulation at the Field-Programmable Gate Array (FPGA). By using FPGA, very rigorous Real-Time (RT) simulation requirements can be met. The response time of the FPGA simulations is significantly reduced, and the time synchronization is better than in a typical RT system implemented in software. The FPGA-based approach is characterized by enormous flexibility...
-
Some geomechanical properties of a biopolymer treated medium sand
PublicationSome geomechanical properties of a biopolymer treated medium sand. This paper presents a laboratory assessment of geomechanical properties of sandy soil improved by biopolymer application. Additives (biosubstance) consist of polysaccharides and water. Biosubstance used in the project was xanthan gum, which comes from bacteria Xanthomonas campestris. Triaxial shear compression tests and unconfi ned compression tests were carried...
-
Local material symmetry group for first- and second-order strain gradient fluids
PublicationUsing an unified approach based on the local material symmetry group introduced for general first- and second-order strain gradient elastic media, we analyze the constitutive equations of strain gradient fluids. For the strain gradient medium there exists a strain energy density dependent on first- and higher-order gradients of placement vector, whereas for fluids a strain energy depends on a current mass density and its gradients....
-
General anaesthesia or sedation for percutaneous aortic valve implantation? The questionnaire results and authors’ experience
Publication -
COVID-19 in Pediatric Intensive Care Units in Poland, PAPITCO-19 Study (Polish Analysis of PICU Trends during COVID-19)
Publication -
Damage Detection Strategies in Structural Health Monitoring of Overhead Power Transmission System
PublicationOverhead power transmission lines, their supporting towers, insulators and other elements create a highly distributed system that is vulnerable to damage. Typical damage scenarios cover cracking of foundation, breakage of insulators, loosening of rivets, as well as cracking and breakage of lines. Such scenarios may result from various factors: groundings, lightning strikes, floods, earthquakes, aeolian vibrations, conductors galloping,...
-
WYBRANE WŁAŚCIWOŚCI FIZYCZNO-CHEMICZNE MIKROSFER I MOŻLIWOŚĆ ICH WYKORZYSTANIA W KOMPOZYTACH CEMENTOWYCH : The selected physico-chemical properties of microspheres and possibility of their use in cement composites
PublicationMicrospheres are formed during the mineral transformation stage in coal combustion. Their content in fly ashes from the combustion of different types of coals varies over a rather wide range from 0.01 to 4.8 wt.%. The microspheres have three main elements, silicon, aluminum and iron, the oxides of which account for about 89.0 wt.% of the material. Mineralogical analysis using XRD shows that microspheres mainly contain mullite and...
-
Arterial cannula shape optimization by means of the rotational firefly algorithm
PublicationThe article presents global optimization results of arterial cannula shapes by means of the newly modified firefly algorithm. The search for the optimal arterial cannula shape is necessary in order to minimize losses and prepare the flow that leaves the circulatory support system of a ventricle (i.e. blood pump) before it reaches the heart. A modification of the standard firefly algorithm, the so-called rotational firefly algorithm,...
-
THE ARCHITECTURE OF DAYLIGHT IN THE DISCOURSE ABOUT THE AESTHETICS OF SUSTAINABILITY
PublicationThe need to create ecological and energy efficient architecture is evident today. In the contemporary discourse on architecture more and more attention is dedicated to the aesthetics that expresses the idea of sustainability. The article is a voice in this debate, concentrating on the architecture that features daylight. Solar light comes from the natural environment and brings some substantial benefits for the architectural space,...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublicationWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Thermal decomposition kinetics of dynamically vulcanized polyamide 6-acrylonitrile butadiene rubber-halloysite nanotube nanocomposites
PublicationThermally stable thermoplastic elastomer nanocomposites based on polyamide 6 (PA6), acrylonitrile butadiene rubber (NBR), and halloysite nanotubes (HNTs) were dynamically vulcanized, and their nonisothermal decomposition kinetics were examined. The Friedman, Kissinger–Akahira–Sunose (KAS), Ozawa–Wall–Flynn (FWO), and modified Coats–Redfern (m‐CR) isoconversional models were used to obtain information about the kinetics of the thermal...
-
Personal Brand Authenticity and Social Media: The Top 5 Football Players’ Case
Publicationhe authenticity is a key factor which attracts the interest of young consumers in the more and more dominant virtual world full of “fake news”,“fake images”, and “fake impressions”. The celebrity authenticity is also important when it comes to gain the positive attitude of the audience and the success in the long term. The unique talent is crucial for all stars. According to football stars, the authenticity of their personal brands...
-
Proposed method for estimating the costs of safety barrier life cycle
PublicationToday barrier types are frequently selected for their price with little regard for the total costs the structure will incur over its lifetime. One of the basic tools designed to manage road infrastructure is the life cycle cost method (LCC, Life cycle cost). It sums up the costs to plan, design, build, operate (use and maintain) and decommission a road structure. Having developed dynamically at the turn of the century the method...
-
The selected roof covering technologies in the aspect of their life cycle costs
PublicationIn the article is presented an analysis of the life cycle costs calculation for selected roof coverings. The scope of research includes costs of construction, maintenance and demolition of the roof covering structure for two alternative technologies – the traditional and new generation. On the presented example of an industrial building with a roof area of 1000 m², the above costs are taken to consideration for the roof covering...
-
Experimental determination of basic mechanical properties of elastomeric polymer
PublicationThere are a lot of different methods of repairing and reinforcing damaged structures, but when it comes to historical buildings and other cultural heritage objects, it is as much about mechanical safety as the aesthetical aspects. Recently, a new and innovative method of repairing damaged structures by filling the cracks with a specially prepared polymer mass has been proposed. This new and innovative technique, known as the Flexible...
-
Recycling of Polyurethanes Containing Flame-Retardants and Polymer Waste Transformed into Flame-Retarded Polyurethanes
PublicationThe growing number of polyurethanes (PUs) produced every year has developed methods for their mechanical and chemical recycling which yield valuable products like substitutes for commercial polyols or flame-retardants. PUs can be produced in different shapes and forms (i.e., elastomers, flexible or rigid foams, coatings, etc.) using several different components (i.e., di- or polyisocyanates, ester- or ether-based polyols, low-molecular...
-
Towards Use of OntoClean for Ontology Contextualization
PublicationOntologies are formal systems of concepts used to describe numerous domains of interest. Ontologies are usually very expressive, but it comes at a price of computationally expensive reasoning over them. In our previous work we discussed the possible performance benefits that can be obtained by decomposing an ontology into contexts. While the benefits are appealing, we discovered that, in our case, the main obstacle against using...
-
The influence of IT-competency dimensions on job satisfaction, knowledge sharing and performance across industries
PublicationPurpose – Technology makes knowledge management easier. Knowledge sharing is essential for organizational development. Job satisfaction fosters knowledge sharing. Hence, this study aims to develop an understanding of the mutual relationship between knowledge sharing and job satisfaction when both are predicted by information technology (IT)-competency dimensions such as IT-operations, IT-knowledge and IT-infrastructure in the context...
-
Lighting conditions in Home Office and occupant’s perception: an international study
PublicationThe global pandemic and physical distancing restrictions are forcing us to rethink how residential buildings are used regarding the visual environment. This paper describes home office lighting conditions within different countries and continents. The aim is to define the current limitations of home offices in providing a resilient visual environment. The work was developed by a team of international experts working together on...
-
Properties of Barium Cerate Thin Films Formed Using E-Beam Deposition
PublicationThis article focuses on the properties of the BaCeO3 thin films formed by electron-beam vapor deposition and investigates the formation of barium cerates on supports with different thermal expansion coefficients (Stainless Steel, Invar, Glass Sealing, and Inconel substrates) and the influence of the technological parameters on the properties of the formed thin films with an emphasis on the stability of the films. Morphology and...
-
High frequency dynamics of an isotropic Timoshenko periodic beam by the use of the Time-domain Spectral Finite Element Method
PublicationIn this work results of numerical simulations and experimental measurements related to the high frequency dynamics of an aluminium Timoshenko periodic beam are presented. It was assumed by the authors that the source of beam structural periodicity comes from periodical alterations to its geometry due to the presence of appropriately arranged drill-holes. As a consequence of these alterations dynamic characteristics of the beam...