displaying 1000 best results Help
Search results for: deceleration capacity
-
Structural Health Monitoring of Composite Shell Footbridge for Its Design Validation
PublicationThe paper presents the structural health monitoring system of the composite bridge for pedestrians and cyclists. The footbridge was designed and manufactured within the FOBRIDGE project. It is the first bridge in the world, which is classified as a consistent single element structural girder, made of sandwich shells, entirely produced in a single cycle. The developed structural health monitoring system, supported design process,...
-
Tin oxide nanoparticles from laser ablation encapsulated in a carbonaceous matrix – a negative electrode in lithium-ion battery applications
PublicationThis report concerns carbonaceous electrodes doped with tin(II) oxide nanoparticles. Tin nanoparticles are obtained by pulsed laser ablation in water. Crystalline nanoparticles have been encapsulated in a carbonaceous matrix formed after pyrolysis of a mixture consisting of tin/tin(IV) oxide nanoparticles and gelatine. The obtained material is characterized by means of X-ray diffraction, selected area diffraction, scanning electron...
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublicationThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
Analysis of Denoising Autoencoder Properties Through Misspelling Correction Task
PublicationThe paper analyzes some properties of denoising autoencoders using the problem of misspellings correction as an exemplary task. We evaluate the capacity of the network in its classical feed-forward form. We also propose a modification to the output layer of the net, which we called multi-softmax. Experiments show that the model trained with this output layer outperforms traditional network both in learning time and accuracy. We...
-
Simulation of parallel similarity measure computations for large data sets
PublicationThe paper presents our approach to implementation of similarity measure for big data analysis in a parallel environment. We describe the algorithm for parallelisation of the computations. We provide results from a real MPI application for computations of similarity measures as well as results achieved with our simulation software. The simulation environment allows us to model parallel systems of various sizes with various components...
-
Low frequency nois of supecapacitor
Open Research DataDataset contains noise measurement results on prototype electrochemical double layer capacitor. The measurement procedure is described in https://dx.doi.org/10.1515/mms-2017-0059.
-
Inline Microstrip Bandpass Filter With Two Transmission Zeros and Increased Order Using Spurious Resonance of Frequency-Dependent Inverter
PublicationA design method for a class of fourth-order inline microstrip bandpass filter with two transmission zeros and 20% fractional bandwidth is presented. The filter consists of two quarter-wavelength transmission-line resonators coupled by a frequency-dependent inverter. The inverter is composed of two open-ended stubs that are connected by an interdigital capacitor and introduces two poles and two transmission zeros in the filter response....
-
Electromagnetic Simulation with 3D FEM for Design Automation in 5G Era
PublicationElectromagnetic simulation and electronic design automation (EDA) play an important role in the design of 5G antennas and radio chips. The simulation challenges include electromagnetic effects and long simulation time and this paper focuses on simulation software based on finite-element method (FEM). The state-of-the-art EDA software using novel computational techniques based on FEM can not only accelerate numerical analysis, but...
-
Barriers to and Facilitators of Scientific Productivity: A Case Study from Polish Technical University
PublicationScientific productivity plays an essential role in the creation of innovation and it stimulates social and economic growth. This study aimed to identify the barriers to and facilitators of scientific productivity in engineering and technology field, as perceived from the perspective of academic managers. Along with quality approach, the study relied on semi-structured interviews with managing bodies, i.e. seven deans and deputy...
-
Effect of excitation intensity on slope stability assessed by a simplified approach
PublicationThe paper concerns the selection of a design accelerograms used for the slope stability assessment under earthquake excitation. The aim is to experimentally verify the Arias Intensity as an indicator of the excitation threat to the slope stability. A simple dynamic system consisting of a rigid block on a rigid inclined plane subjected to horizontal excitation is adopted as a slope model. Strong ground motions recorded during earthquakes...
-
Thermal boundary conditions to simulate friction layers and coatings at sliding contacts
PublicationA brief review of the thermal boundary conditions specified at sliding interfaces was performed. New thermal boundary conditions were derived aimed at solving problems of sliding with account of surface layers representing friction layers and tribological coatings. Based on the assumption of linear temperature distributions in the surface layers, the proposed conditions enable one to simplify simulations by eliminating the surface...
-
Ammonia amendment promotes high rate lactate production and recovery from semi-continuous food waste fermentation
PublicationIn this study, a reliable approach using ammonia nitrogen was proposed to increase lactate production during semi-continuous food waste (FW) fermentation under mesophilic conditions. Both free ammonia nitrogen (FAN) and ammonium ion (NH4+-N) were present in mesophilic reactors, with a wide FAN/NH4+-N ratio variation due to the intermittent pH control. The investigation of responsible mechanisms revealed that the increased production...
-
An in situ technique for the assessment of adhesive properties of a joint under load
PublicationSlow crack propagation in adhesive bonded joints has been characterised using an asymmetric wedge test. Crack position was evaluated from strain gauge measurements, both in the debonded partof the joint and in the bonded zone. Test temperature was changed during loading, giving insight into bond evolution. The technique allows accurate, and virtually continuous, determination of crack position to be made, and therefore the evaluation...
-
Feasibility Study for Food Intake Tasks Recognition Based on Smart Glasses
PublicationIn this exploratory study 13 adult test subjects have performed different food intake tasks while wearing a three axis accelerometer mounted at a temple of glasses. Two different algorithms for task recognition have been applied and compared. The retrospective data processing leads to better task recognition results when the frequency range of 50 Hz to 100 Hz is analysed within accelerometer signal recordings. A straightforward...
-
Histogram of Oriented Gradients with Cell Average Brightness for Human Detection
PublicationA modification of the descriptor in a human detector using Histogram of Oriented Gradients (HOG) and Support Vector Machine (SVM) is presented. The proposed modification requires inserting the values of average cell brightness resulting in the increase of the descriptor length from 3780 to 3908 values, but it is easy to compute and instantly gives ≈ 25% improvement of the miss rate at 10‒4 False Positives Per Window (FPPW). The...
-
Application of Fracture Mechanics for Energetic Effects Predictions While Wood Sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (or power - more interesting from energetic point of view) could be considered from a point of view of modern fracture mechanics. Cutting...
-
Damaged plasticity model - seismic analysis of structure of the Petronas Twin Towers (Kuala Lumpur) in Malaysia
PublicationThe article presents numerical simulations for the modelling of seismic impact on the structure of Petronas Twin Towers (Kuala Lumpur) in Malaysia with application of two methods. The Response Spectrum method, in which a spectrum of the structure's responses to an earthquake's impact is generated and the Acceletogram (BETA) method, in which we generate dynamic load in the form of a diagram of the connection between acceleration...
-
How proteins bind to DNA: target discrimination and dynamic sequence search by the telomeric protein TRF1
PublicationTarget search as performed by DNA-binding proteins is a complex process, in which multiple factors contribute to both thermodynamic discrimination of the target sequence from overwhelmingly abundant off-target sites and kinetic acceleration of dynamic sequence interrogation. TRF1, the protein that binds to telomeric tandem repeats, faces an intriguing variant of the search problem where target sites are clustered within short fragments...
-
Design of Resilient Vehicle-to-Infrastructure Systems
PublicationVehicular ad hoc networks (VANETs) have recently gained noticeable attention due to advantages in improving road traffic safety, shaping the road traffic and providing infotainment opportunities to travellers. However, transmission characteristics following from the IEEE 802.11p standard and the high mobility of VANET nodes remarkably reduce the lifetime, reach and capacity of wireless links, and often lead to simultaneous disruptions...
-
Demolition of the cereal elevator building located in the conservation protection zone in the aspect of technical, functional-utility and economic conditions
PublicationThe paper presents a description of the technical condition of the Grain Elevator building situated on the port quay, which after many years of operation has been decommissioned. The immediate reason for the cessation of operation was the change in the use profile of the port quay, which caused the handling of other goods at the quay than the bulk materials originally stored in Elewator Zbożowy. The work contains...
-
Flexural behaviour of concrete slabs reinforced with FRP bars in experiments and according to aci ACI 440.1R guide
PublicationThe paper presents research conducted on two concrete slabs reinforced with the carbon composite bars and two other concrete slabs reinforced with basalt composite bars. The carbon bars were plain, while the basalt ones were ribbed. The slabs were experimentally investigated in the flexural state of effort with the concentrated forces applied. The results are compared with the analytical solution proposed in the guide ACI 440.1R-06...
-
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublicationThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublicationThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Synthesis, structure and physical properties of new intermetallic spin glass-like compounds RE2PdGe3 (RE = Tb and Dy)
PublicationNew intermetallic compounds Tb2Pd1.25Ge2.75 and Dy2Pd1.25Ge2.75 have been synthesized using the arc-melting method. The crystallographic structure and magnetic, electronic transport, and thermal properties are reported. The crystal structure obtained from powder x-ray diffraction analysis suggests that these compounds crystallize in the AlB2-type structure (space group P6/mmm, no. 191) with lattice parameters a = 4.228 53(5)/4.230 54...
-
Superconductivity on a Bi Square Net in LiBi
PublicationWe present the crystallographic analysis, superconducting characterization and theoretical modeling of LiBi, that contains the lightest and the heaviest nonradioactive metal. The compound crystallizes in a tetragonal (CuAu-type) crystal structure with Bi square nets separated by Li planes (parameters a = 3.3636(1)Å and c = 4.2459(2) Å, c/a = 1.26). Superconducting state was studied in detail by magnetic susceptibility and heat...
-
Diatoms Biomass as a Joint Source of Biosilica and Carbon for Lithium-Ion Battery Anodes
PublicationThe biomass of one type cultivated diatoms (Pseudostaurosira trainorii), being a source of 3D-stuctured biosilica and organic matter—the source of carbon, was thermally processed to become an electroactive material in a potential range adequate to become an anode in lithium ion batteries. Carbonized material was characterized by means of selected solid-state physics techniques (XRD, Raman, TGA). It was shown that the pyrolysis...
-
Study of QoS Parameters Measurement Methodology and Requirements in RSMAD
PublicationThe paper presents the results of analysis and research of the quality of service requirements (defined by the QoS parameters) for data transmission services in Radio System for Monitoring and Acquisition of Data from Traffic Enforcement Cameras (in short: RSMAD). The paper also presents and discusses the results of test of impact of the size of images from traffic enforcement cameras (TECs) on the average transmission time. Moreover,...
-
Simple and low-cost wireless voting system
PublicationThis paper presents the concept of a simple and low-cost wireless voting system working on the 868 MHz frequency band. Described system is dedicated to general shareholders assemblies but it can be easily adapted for other applications. The main advantage is its simplicity and mobility as it consists solely of three components - voting modules, base station and a PC application from which the whole system is managed. This architecture...
-
Preliminary experimental research on stability of truss' joint with positive eccentricity
PublicationRecently, a very large interest in lightweight steel structures made from cold-formed sections has been noticeable. In the design practice, a large emphasis is put on rational shaping of both the thin-walled elements and constructions designed on them. The aim of this paper is to present the methodology for preparation of experimental research that model the behaviour of members in trusses made of cold-formed sections with positive...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublicationSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
Sorption of Chlorinated Solvents on Pine and Oak sawdust
PublicationThe article presents assessment of pine and oak sawdusts as sorbents for removal of chlorinated solvents from water. Sawdusts as potential sorbents were characterized with elemental analysis and BET analyses. Sorption capacity was determined for both pine and oak sawdust towards 1,1,2-trichloroethane, tetrachloroethene and 1,1,1,2-tetrachloroethane. Pine sawdust was able to adsorb greater amounts of chlorinated solvents compared...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
Simple and low-cost wireless voting system
PublicationThis paper presents the concept of a simple and low-cost wireless voting system working in the 868 MHz frequency band. The described system is dedicated to general shareholders assemblies but it can be easily adapted for other applications. The main advantage is its simplicity and mobility as it consists solely of three components - voting modules, a base station and a PC application from which the whole system is mamaged. This...
-
Optimization of Hydrogen - Evolving Photochemical Molecular Devices
PublicationA molecular photocatalyst consisting of a RuII photocenter, a tetrapyridophenazine bridging ligand, and a PtX2 (X=Cl or I) moiety as the catalytic center functions as a stable system for light-driven hydrogen production. The catalytic activity of this photochemical molecular device (PMD) is significantly enhanced by exchanging the terminal chlorides at the Pt center for iodide ligands. Ultrafast transient absorption spectroscopy...
-
Microcracking monitoring and damage detection of graphene nanoplatelets-cement composites based on acoustic emission technology
PublicationThis study aims to identify the micro-cracking pattern and structural applications of cement composites replaced with 0 wt%, 0.04 wt%, and 0.08 wt% contents of graphene nanoplatelets (GNPs) over cement weight through acoustic emission (AE) monitoring under mechanical degradation. The ultraviolet-visible spectroscopy (UV–vis) results showed that at 60 min sonication period, GNP-4 showed maximum absorbance rate of 16.15% compared...
-
Modelling Signalised Intersections Reliability of Functioning
PublicationThe article addresses a fundamental aspect of traffic, i.e. the operation of traffic signals at intersections, in reference to the reliability theory. In many cases, when intersections carry substantial amounts of traffic, selecting control parameters to produce satisfactory traffic conditions is quite difficult. Design methods do not cover all possible situations which are the result of intersection geometry and location...
-
An Easy and Ecological Method of Obtaining Hydrated and Non-Crystalline WO3−x for Application in Supercapacitors
PublicationIn this work, we report the synthesis of hydrated and non-crystalline WO3 flakes (WO3−x) via an environmentally friendly and facile water-based strategy. This method is described, in the literature, as exfoliation, however, based on the results obtained, we cannot say unequivocally that we have obtained an exfoliated material. Nevertheless, the proposed modification procedure clearly affects the morphology of WO3 and leads to loss...
-
Possibilities of Phoslock® application to remove phosphorus compounds from wastewater treated in hybrid wetlands
PublicationTreatment wetland technologies for wastewater treatment can be easily applied for removal of all pollutants except phosphorous. They are applicable in a small towns and rural areas, places where conventional wastewater treatment plant cannot properly operate because of common economic constraints. In Poland only the 8% of rural areas are equipped with sewer system, thus treatment wetlands might be an alternative, effective and...
-
Single-phase, Five-level Inverter with SPWM-Based Neutral Point Voltage Balancing Scheme
PublicationMultilevel inverter topologies provide several advantages over two-level inverter configuration. These benefits are the reason for the growing interest in multilevel topologies among research society. One of the most popular topological concepts (diode and active switch clamping) requires neutral-point potential balancing due to series-connected capacitor banks across the input dc link in such derived inverter configurations. This...
-
Influence of configurations of the beds on contaminations removal in hybrid constructed wetlands.
PublicationThree hybrid constructed wetlands in configuration HF-VF-HF in Poland and one with another configuration VF-HF-Pond in Gremany were analysed. These hybrid constructed wetlands provide the second stage biological treatment. They are located in Pommerania region, in Sarbsk, Wiklino and Wieszyno, and their capacities are 29.7, 18.6 and 24.5 m3/day, respectively. The analysed system in Germany in Waizenfeld (Gemeinde Pommelsbrunn,...
-
ISSUES OF ECONOMIC ANALYSIS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublicationThis article presents basic dependences for conducting a technical and economic analysis related with investment projects. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to generate electric energy in the so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine system...
-
LNG TANK IN ŚWINOUJŚCIE: NONLINEAR ANALYSIS OF THE TANK DOME ELEMENTS BEHAVIOUR
PublicationIn this paper, the dome of a tank in the Świnoujście LNG terminal is analysed. Some of the rafter ribs at the connection with hangers were not mounted during construction of the tank dome. Therefore, it has become necessary to estimate its response, which has been done with the aid of some computational models of the dome, that have been created in the finite element method environment. Different local models are studied, aiming...
-
Hybrid energy storage forelectric multiple units to operate at the partially electrified line Gdynia -Hel
PublicationThe article presents calculations enabling the selection of an on-board energy storage device to replace diesel-powered trains with modern storage multiple units on the example railway line Gdynia Główna -Hel. The pioneering and currently used storage electric multiple units, mainly in Europe, were presented. The condensed results of the inventory of the line in question, including the technical condition...
-
Intermetallic disordered magnet Gd2Pt1.1Ge2.9 and its relation to other AlB2 -type compounds
PublicationThe intermetallic germanide Gd 2 Pt 1.1 Ge 2.9 was synthesized using an arc-melting method. The crystal structure was characterized using powder x-ray diffraction, revealing a disordered ternary AlB 2 -type structure (space group P 6 / m m m , No. 191) with lattice parameters a = 4.2092 ( 1 ) Å and c = 4.0546 ( 2 ) Å . Physical properties were investigated by magnetic susceptibility and heat capacity measurements, which...
-
A Novel Iterative Decoding for Iterated Codes Using Classical and Convolutional Neural Networks
PublicationForward error correction is crucial for communication, enabling error rate or required SNR reduction. Longer codes improve correction ratio. Iterated codes offer a solution for constructing long codeswith a simple coder and decoder. However, a basic iterative code decoder cannot fully exploit the code’s potential, as some error patterns within its correction capacity remain uncorrected.We propose two neural network-assisted decoders:...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublicationThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
Microemulsion Delivery Systems with Low Surfactant Concentrations: Optimization of Structure and Properties by Glycol Cosurfactants
PublicationExtensive use of microemulsions as delivery systems raises interest in the safe ingredients that can form such systems. Here, we assessed the use of two glycols, i.e., propylene glycol and pentylene glycol, and their mixtures to manipulate the properties and structure of microemulsions. Obtained systems with glycols were extensively characterized in terms of capacity to incorporate water phase, droplet size, polydispersity, structure...
-
MXene-based materials for removal of antibiotics and heavy metals from wastewater– a review
PublicationAs a novel family of 2D materials, MXenes provide an extensive variety of applications in water and effluent treatment due to their distinctive properties and attractive applicability, including superior electrical conductivity, higher thermal stability, hydrophilicity, and high sorption-reduction capacity. Their excellent sorption selectivity makes them perfect for removing hazardous contaminants. Currently, MXene-based materials...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublicationAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
The impact of material degradation on the resistance and reliability of truss structures
PublicationThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...