displaying 1000 best results Help
Search results for: ROUTE RECONSTRUCTION
-
Critical analysis of laboratory measurements and monitoring system of water-pipe network corrosion-case study.
PublicationCase study of corrosion failure of urban water supply system caused by environmental factors was presented. Nowadays corrosion monitoring of water distribution systems is an object of major concern. There is possibility of application broad range of techniques like gravimetric and electrochemical. Both kinds of techniques can be applied in laboratory and field conditions. In many cases researches limit the case analysis to measurements...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublicationThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
The aluminium and polycarbonate covering to the roof over the stadium in Gdańsk
PublicationThis paper presents information about structural elements of the roof covering to the stadium in Gdansk built for the 2012 European Football Championship in Poland and the Ukraine. The paper discusses elements of the polycarbonate covering, the supporting structure and the drainage system. It also provides information about tests and research performed prior to construction, which determined the solutions adopted as well as...
-
Strucutral steel - tensile test results
Open Research DataModern floating structures such as ships, oil platforms and offshore wind towers are built mostly of structural steel. It is a material that is subject to requirements which, when met, allows the construction and safe operation of the structure throughout its entire work cycle. One of the basic criteria that a material must meet is its strength. The...
-
Processing, physico-mechanical and thermal properties of reclaimed GTR and NBR/reclaimed GTR blends as function of various additives
PublicationIn this work, ground tire rubber (GTR) was mechano-chemically reclaimed in the presence of bitumen and various additives. During studies three types of processing and curing additives: (i) peptizer P300; (ii) vulcanization accelerator tetramethylthiuram disulfide (TMTD) and (iii) organic peroxide di(2-tert-butyl-peroxyisopropyl)benzene (BIB1) were applied to enhance reclaiming of GTR. Reclaiming process was evaluated by oscillating...
-
Raman investigation of the patina layers on Hungarian copper ingots from a fifteenth century shipwreck
PublicationWe report results of the patina study of underwater archeological finding ofmedieval copper objects performed by means of the Raman and complementary spectroscopic techniques. The objects were found submerged in the sea as cargo part of the ship which sunk in the Gulf of Gdańsk in 1408. The excavated collection consists of 230 oval ingots of the size and mass up to about 60 cm and 18 kg (total of 2 tons), respectively. In the Raman...
-
Lanthanide co-doped TiO2: the effect of metal type and amount on surface properties and photocatalytic activity
PublicationPreparation of new rare earth metal-containing TiO2 nanocomposites (Nd3+/Er3+, Nd3+/Eu3+, Eu3+/Ho3+-TiO2) using sol–gel route and their photoactivity under visible and ultraviolet light is reported. The obtained photocatalysts were subsequently characterized by Brunauer–Emmett–Teller (BET) method, UV–Vis diffuse-reflectance spectroscopy (DRS), luminescence spectroscopy, X-ray photoelectron spectroscopy (XPS) and X-ray powder diffraction...
-
Effect of molar ratio [NCO]/[OH] groups during prepolymer chains extending step on the morphology and selected mechanical properties of final bio‐based thermoplastic poly(ether‐urethane) materials
PublicationThe main aim of this work was to investigate the effect of [NCO]/[OH] molar ratio used during the prepolymer chain extending step (with bio‐based diols) on the chemical structure, and thermomechanical and mechanical properties of thermoplastic poly(ether‐urethane)s. Thermoplastic poly(ether‐urethane)s were obtained from bio‐based polyol (polytrimethylene ether glycol), bio‐based glycol (1,4‐butanediol or 1,3‐propanediol), and 4,4'diphenylmethane...
-
Mercury concentration in the sediments as a function of changing climate in coastal zone of Southern Baltic Sea – preliminary results
PublicationMercury, despite of its many uses in industry, is also highly toxic. It is highly neurotoxic, and because of the ability of mercury to penetrate placental barrier, in some countries ban on predatory fish consumption (the main route of mercury into human organism) by pregnant women was introduced. There are very little publications describing the consequences of weather anomalies on contaminants cycles. No research was published...
-
Light-improved glucose sensing on ordered Au-Ti heterostructure
PublicationNon-enzymatic electrochemical platforms sensitive towards glucose presence have attracted a worldwide attention during last decades. We report on influence of solar light onto response of gold-titanium heterostructures prepared via controllable approach. The material based on Au nanoparticles orderly distributed over the structured titanium foil was obtained by electrochemical anodization followed by chemical etching, magnetron...
-
Ultrasound-assisted heterogeneous activation of persulfate and peroxymonosulfate by asphaltenes for the degradation of BTEX in water
PublicationThis study investigated – for the first time - the simultaneous degradation of benzene, toluene, ethylbenzene and o-xylene (BTEX) by persulfate (PS) and peroxymonosulfate (PMS) activated by asphaltenes (Asph) under ultrasound (US) irradiation. Advantageous properties such as high thermal stability, low production cost and extensive availability make asphaltenes as an appealing carbonaceous material for heterogeneous catalysis....
-
Design and synthesis of TiO2/Ti3C2 composites for highly efficient photocatalytic removal of acetaminophen: The relationships between synthesis parameters, physicochemical properties, and photocatalytic activity
PublicationIn this study, we report the potential of TiO2/Ti3C2 composite fabricated by oxidation of MXene for degradation of persistent organic pollutants. The effect of the synthesis conditions (time, temperature, and reaction environment) on the morphology, physicochemical properties, and photocatalytic activity was investigated. It was found that acetaminophen degradation was positively correlated with TiO2 content in the composite structure. Furthermore,...
-
Janusz Kozak prof. dr hab. inż.
PeopleJanusz KOZAK Born 04.07.1953 Puck, Poland Intermediate school” Technikum Budowy Okrętów „Conradinum” Gdansk, 1973. Graduated on Faculty of Shipbuilding of Gdańsk University of Technology, Poland, 1978. Employed: From 1978 - Gdynia Shipyard 1978 as designer, from 1980 as a specialist in Chair of Technology in Faculty of Shipbuilding of Gdańsk University of Technology, 1993 as assistant, PhD (1993), “Method for assessment...
-
Weak localization competes with the quantum oscillations in a natural electronic superlattice: The case of Na1.5(PO2)4(WO3)20
PublicationWe report an investigation of the combined structural and electronic properties of the bronze Na1.5(PO2)4(WO3)20. Its low-dimensional structure and possible large reconstruction of the Fermi surface due to charge density wave instability make this bulk material a natural superlattice with a reduced number of carriers and Fermi energy. Signatures of multilayered two-dimensional (2D) electron weak localization are consequently reported,...
-
Application of Intelligent Conversational Agents in E-learing Environments
PublicationThe paper concerns intelligent tutoring systems and concentrates on apliaction of virtual mentors in distance learning environments. Different educational agent types are described. The prototype of an agent developed at Gdansk University of Technology is also presented, as well as its internal representation and construction. Benefits of virtual mentors applied in distance learning are also pointed out.
-
Blast Charge Technique as a Method of Soil Improving to Locate the New Supporting Runways
PublicationA quick and effective method of reinforcing the ground base designed for the construction of engineering structures used for performing various types of air operations was presented. It allows to use wastelands, wetlands, swamps, etc. for these purposes, thus creating a dispersed network of landing sites, increasing the access of large social groups to air transport and increasing their mobility.
-
Uniwersalny program komputerowy do projektowania zmiany kierunku trasy
PublicationW pracy przedstawiono kolejny program komputerowy stanowiący implementację algorytmu obliczeniowego dotyczącego projektowania zmiany kierunku trasy kolejowej, dostosowanego do techniki ciągłych pomiarów satelitarnych. Program ten ma charakter uniwersalny, gdyż w ogólnym przypadku obejmuje wprowadzenie do układu geometrycznego dwóch łuków kołowych o różnym promieniu, czyli zastosowanie łuku koszowego. Może się to okazać szczególnie...
-
Recent steel structures in Poland - the selected projects
PublicationThe paper presents selected examples of recently completed steel structures in Poland. These are roofs over sport stadiums, construction of public buildings and bridges. Described examples do not exhaust the acquis in the field of steel constructions in Poland. The authors, however, may hope that the presented con-structions represents current achievements in Poland in the field of steel structures.
-
Five-phase Induction Motor Drive Operation During Stator Phase Fault
PublicationThe article presents the most important advantages of multi-phase electric drives. The construction of a five-phase squirrel cage induction motor together with possible stator winding distribution cases is presented, which affect the properties of such motor. Increased reliability of five-phase drives was indicated. The drive operation properties were confirmed by experimental results.
-
Nomination Dossier, The Modernist Centre of Gdynia, Part 2b, History and Development
PublicationHistory and development of Gdynia, from Medieval times up until today. The project concerns such chapters as: Introduction; The village of Gdynia; Gdynia as a seaside resort; Construction of the port and the city in the interwar period; The modernist city centre – layout; architecture;Architecture of the city centre; South Pier and Grand District; Post-war development of Śródmieście: a continuation
-
The Transmission Protocol of Sensor Ad Hoc Networks
PublicationThis paper presents a secure protocol for a radio Ad Hoc sensor network. This network uses the TDMA multiple access method. The transmission rate on the radio channel is 57.6 kbps. The paper presents the construction of frames, types of packets and procedures for the authentication, assignment of time slots available to the node, releasing assigned slots and slots assignment conflict detection.
-
Video traffic data - Interchange Lotnisko (S2-S79) - Exit +entry lanes, Poland
Open Research DataThe data includes video traffic data registered with 8 video cameras at entry or exit lanes of the Lotnisko interchange within S2 expressway in Poland (interchange of expressway S2 and expressway S79), located in the Warsaw Agglomeration. The data covers the one day: 05.09.2017 (expressway S2).
-
Linear impedance as a function of A.C. voltage for 50(2Bi2O3-V2O5)-50SrB4O7 glass-ceramic heat-treated at 813 K measured with impedance spectroscopy method at high temperature region
Open Research DataThe linear electrcial properties as a function of A.C. voltage of 50(2Bi2O3-V2O5)-50SrB4O7 glass-ceramic heat treated at 813 K was measured by impedance spectroscopy method.
-
The role of isolated farmsteads in the open landscape protection on the example of Kashubia
PublicationAs a result of the social and economic transformation of rural areas, open landscapes are disappearing. Former farmsteads are being devastated or beginning to lose their landscape context due to the spread of residential building development. At the same time, in many places, the farmstead form is clearly legible and remains an element with which the view is structured and enriched. The article was aimed at drawing attention to...
-
Review on robust laser light interaction with titania – Patterning, crystallisation and ablation processes
PublicationTitanium dioxide is regarded as a very promising semiconducting material that is widely applied in many everyday-use products, devices, and processes. In general, those applications can be divided into energy or environmental categories, where a high conversion rate, and energy and power density are of particular interest. Therefore, many efforts are being put towards the elaboration of novel production routes, and improving the...
-
DETERMINING THE TIME CONSTANT USING TWO METHODS AND DEFINING THE THERMOCOUPLE RESPONSE TO SINE EXCITATION OF GAS TEMPERATURE
PublicationThis paper describes the two methods of determining the time constant of type K thermocouple, for two construction solutions: the exposed weld and the mantle fillet weld. This is an important parameter indicating the response time of the thermocouple on the recorded signal. The first method consists of determining the value of τ in the way of numerical simulation of heat exchange between the thermocouple and the current of gas...
-
Advances in olfaction-inspired biomaterials applied to bioelectronic noses
PublicationAmong all the senses, olfactory system of mammals is the least characterised as far as the mechanisms of odour identification are concerned. The results of recent investigations allow better understanding of the operation mechanism of the sense of smell. Progress in this field is crucial for the development of sensor technology based on olfaction-inspired biomaterials, which simulate the olfactory system of the biological counterparts....
-
Radar technique in application of interlayer identification connections
PublicationOne of important issues in pavement construction is to ensure that layers applied directly one on top of the other make up a continuous whole and form an integral construction complex. An appropriate interlayer connection plays here significant role ensuring proper transmission of distortions generated by wheels of vehicles to lower layers and preventing water penetration between the layers. In case of damaged pavements where lack...
-
Palm Oil Fuel Ash-Based Eco-Efficient Concrete: A Critical Review of the Short-Term Properties
PublicationThe huge demand for concrete is predicted to upsurge due to rapid construction developments. Environmental worries regarding the large amounts of carbon dioxide emanations from cement production have resulted in new ideas to develop supplemental cementing materials, aiming to decrease the cement volume required for making concrete. Palm-oil-fuel-ash (POFA) is an industrial byproduct derived from palm oil waste’s incineration in...
-
The Eastern Battery in Świnoujście, Poland - history and architecture of a Prussian coastal fort from the 19th century
PublicationThe article describes the history, architecture and development of the Eastern Battery (also known as the Gerhard Fort) – one of three remaining coastal forts in Świnoujście (former Swinemünde) located in northern Poland, by the Baltic Sea. The research is mostly based on historical cartographic material and architectural plans verified during field studies. This data served to create a digital model – one of the results of the...
-
Reduced-cost surrogate modeling of input characteristics and design optimization of dual-band antennas using response features
PublicationIn this article, a procedure for low-cost surrogate modeling of input characteristics of dual-band antennas has been discussed. The number of training data required for construction of an accurate model has been reduced by representing the antenna reflection response to the level of suitably defined feature points. The points are allocated to capture the critical features of the reflection characteristic, such as the frequencies...
-
Effect of coarse grain aggregate on strength parameters of two-stage concrete
Publication. Two-stage concrete (TSC) is a special type of concrete that the method of its construction and implementation is different from conventional one. In TSC, coarse aggregate particles are first placed in the formwork and voids between them are subsequently injected with a special cementations mixture. TSC has been successfully used in many applications, such as underwater construction, casting concrete sections congested with reinforcement...
-
Tuning of the finesse coefficient of optoelectronic devices
PublicationOptoelectronic devices attracted considerable attention in many branches of science and technology, which can be attributed to their unique properties. Many of them use optical cavities which parameters can be adopted to specific requirements. This thesis investigates the introduction of diamond structures (nitrogen-doped diamond film, boron-doped diamond film, undoped diamond sheet) to optical cavities to tune their finesse coefficient....
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublicationThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Study on the Positioning Accuracy of the GNSS/INS System Supported by the RTK Receiver for Railway Measurements
PublicationCurrently, the primary method for determining the object coordinates is positioning using Global Navigation Satellite Systems (GNSS) supported by Inertial Navigation Systems (INS). The main goal of this solution is to ensure high positioning availability, particularly when access to satellite signals is limited (in tunnels, areas with densely concentrated buildings and in forest areas). The aim of this article is to determine whether...
-
Comparison of non-linear statical analysis of truss with linear and rotational side supports and 3d roof model
PublicationIn the paper geometrically non-linear analysis of example truss with linear and rotational elastic side supports is compared with geometrically non-linear analysis of part of the roof construction with purlins and truss-bracing. For different stiffness of side-supports a non linear relation between normal force in compressed chord due to out of truss plane displacement has been calculated.
-
The secure transmission protocol of sensor Ad Hoc network
PublicationThe paper presents a secure protocol of radio Ad Hoc sensor network. This network operates based on TDMA multiple access method. Transmission rate on the radio channel is 57.6 kbps. The paper presents the construction of frames, types of packets and procedures for the authentication, assignment of time slots available to the node, releasing assigned slots and slots assignment conflict detection.
-
Problems of Active Dynamic Thermography Measurement Standardization in Medicine
PublicationReliability of thermographic diagnostics in medicine is an important practical problem. In the field of static thermography, a great deal of effort has been made to define the conditions for thermographic measurements, which is now the golden standard for such research. In recent years, there are more and more reports on dynamic tests with external stimulation, such as Active Dynamic Thermography, Thermographic Signal Reconstruction...
-
Imaging of Increasing Damage in Steel Plates Using Lamb Waves and Ultrasound Computed Tomography
PublicationThis paper concerns inspection of steel plates, with particular emphasis on the assessment of in-creasing damage. Non-destructive tests were performed on four plates, one of which was un-damaged, while the remaining three had a defects in the form of circular holes with a diameter of 2, 5, and 10 cm. Guided Lamb waves were used in the research, and the image reconstruction was performed using ultrasound computed tomography. The...
-
Spatially variant PSF modeling in confocal macroscopy
PublicationThe point spread function (PSF) of imaging systems plays an essential role in image reconstruction. In the context of confocal microscopy, optical performance degrades towards the edge of the field of view. In confocal macroscopy, the related artifacts are even stronger, as the field of view is much larger. Because the related PSFs are strongly spatially variant, it is essential to be able to model them with few parameters. The...
-
Bounds on the cover time of parallel rotor walks
PublicationThe rotor-router mechanism was introduced as a deterministic alternative to the random walk in undirected graphs. In this model, a set of k identical walkers is deployed in parallel, starting from a chosen subset of nodes, and moving around the graph in synchronous steps. During the process, each node successively propagates walkers visiting it along its outgoing arcs in round-robin fashion, according to a fixed ordering. We consider...
-
Environmental Fate of Two Psychiatric Drugs, Diazepam and Sertraline: Phototransformation and Investigation of their Photoproducts in Natural Waters
PublicationExperimental studies were conducted to investigate the photodegradation of diazepam and sertraline, two of the most frequently used psychiatric drugs, induced by xenon lamp irradiation, which overlap the sunlight spectra, and natural sunlight. Degradation kinetics was established indicating the occurrence of autocatalytic reactions. The application of liquid chromatography coupled to quadrupole time-of-flight mass spectrometry...
-
Ergonomic Aspects of Development of Architecture in the Context of Sanitary and Hygiene Safety
PublicationAbstract Ergonomics answers the need of safe development of space by creating spatial forms which help to implement the safety procedures and limit the threats involved both in ordinary use of the spaces and in case of unforeseen events. Using the knowledge of ergonomics and architecture on the basis of defining the routes of germ transmission, allows to limit the spread of those organisms. Ergonomics of developing architectural...
-
A novel approach exploiting properties of convolutional neural networks for vessel movement anomaly detection and classification
PublicationThe article concerns the automation of vessel movement anomaly detection for maritime and coastal traffic safety services. Deep Learning techniques, specifically Convolutional Neural Networks (CNNs), were used to solve this problem. Three variants of the datasets, containing samples of vessel traffic routes in relation to the prohibited area in the form of a grayscale image, were generated. 1458 convolutional neural networks with...
-
Isocyanate-Free Polyurethanes
PublicationIsocyanate-free polyurethanes (also called non-isocyanate polyurethanes, or NIPUs) are alternatives to the conventional (commercially used) polyurethanes synthesized using di- or polyisocyanates, polyols, and chain extenders with low molecular weight. The major routes of NIPUs’ synthesis involve polyaddition of cyclic carbonates and di- or polyamines, polycondensation of carbamates, and diols. The most important intermediates are...
-
Synthesis Methods and Favorable Conditions for Spherical Vaterite Precipitation: A Review
PublicationVaterite is the least thermodynamically stable anhydrous calcium carbonate polymorph. It exists very rare in nature, e.g. in some rock formations or as a component of biominerals produced by some fishes, crustaceans or birds. Synthetic vaterite particles are proposed as carriers of active substances in medicines, additive in cosmetic preparations as well as adsorbents. Also, their utilization as a pump for microfluidic flow is...
-
Electrophoretic co-deposition of Mn1.5Co1.5O4, Fe2O3 and CuO: Unravelling the effect of simultaneous addition of Cu and Fe on the microstructural, thermo-mechanical and corrosion properties of in-situ modified spinel coatings for solid oxide cell interconnects
PublicationA systematic microstructural, thermo-mechanical and electrical characterization of simultaneous Fe–Cu doped Mn–Co spinel coatings processed by electrophoretic co-deposition on Crofer 22 APU is here reported and discussed. An innovative approach for the simultaneous electrophoretic deposition of three spinel precursors is designed, conceived and optimised, with the aim of outlining time- and energy-saving spinel modification routes....
-
Designing of Track Axis Alignment with the Use of Satellite Measurements and Particle Swarm Optimization
PublicationDesigning of the track’s alignment is a key issue from the point of view of maintaining of proper geometries. The paper presents a design method for sections of railway line located in the horizontal arch. The method is adapted to the technique of mobile satellite measurements. The general principles of this measurement method have been described in the article. A project's solution has been presented using mathematical notation...
-
Cadmium complex possessing simultaneously silanethiolato- and dithiocarbamato-ligands. A novel single-source precursor of cadmium sulfide
PublicationThermal decomposition of suitable coordination compounds may be used as efficient route for fabrication of semiconducting layers. A new potential CdS precursor—a cadmium complex with all-sulfur Cd-coordination sphere [Cd{l-SSi(OBut)3}(S2CNC4H8)]2 (1) —has been prepared and its properties are investigated. The complex was obtained in the reaction between dimeric bis(tri-tert-butoxysilanethiolato) cadmium(II) [Cd{SSi(OBut)3}2]2 and...
-
The need for linear revitalization. Gdynia case
PublicationThe aim of the article is to discuss the need of defining and implementation of the linear revitalization - the new approach related to the revitalization processes. The results of the preliminary investigations indicate that this kind of revitalization seems to be an important tool supporting city management and planning, especially in cases of cities fragmentation - causing lack of physical, social, economic and ecological cohesion....