Filters
total: 31423
filtered: 17473
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: THERMAL EFFECTS, HYDRODYNAMIC JOURNAL BEARING, WATER-LUBRICATION, EXPERIMENTAL TESTS, NUMERICAL SIMULATIONS
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublicationThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
Deep learning based thermal image segmentation for laboratory animals tracking
PublicationAutomated systems for behaviour classification of laboratory animals are an attractive alternative to manual scoring. However, the proper animals separation and tracking, especially when they are in close contact, is the bottleneck of the behaviour analysis systems. In this paper, we propose a method for the segmentation of thermal images of laboratory rats that are in close contact during social behaviour tests. For this, we are...
-
Water Behavior Near the Lipid Bilayer
PublicationIn this chapter, we focus on the dynamics of water molecules situated in the vicinity of a phospholipid bilayer. Using a molecular dynamics simulation method, we studied interactions between water and the bilayer and tracked trajectories of the water molecules. Based on the hypothesis that molecules trapped inside the bilayer make different motions than the ones which are either attached to the surface or move freely in the water...
-
Experimental verification of natural convective heat transfer phenomenon from isothermal cuboids
PublicationArtykuł przedstawia wyniki badań eksperymentalnych konwekcyjnej wymiany ciepła od powierzchni izotermicznego prostopadłościanu o stosunkowo dużych rozmiarach (t.j. 1.5 m x1 m x 0.5 m). Celem tych badań było otrzymanie wyników, które można by porównać z otrzymanymi dla obiektu w mniejszej skali i prezentowano we wcześniejszych doniesieniach (Int. J. Heat Mass Transfer 46 (2003) 2169-2178). Rozwiązanie eksperymentalne przeprowadzono...
-
Effects of Urea and Trimethylamine-N-oxide on the Properties of Water and the Secondary Structure of Hen Egg White Lysozyme
PublicationW celu określenia sposobu hydratacji mocznika i N-tlenku trimetyloaminy, wykorzystano spektroskopię oscylacyjną FTIR. Dane eksperymentalne, otrzymane z pomiarów widm oscylacyjnych wody półciężkiej (HDO) rozcieńczonej izotopowo w wodnych roztworach badanych związków, analizowane były za pomocą "metody widm różnicowych". Strukturalno-energetyczna charakterystyka wody zaburzonej przez cząsteczki osmolitów wskazuje, że woda zaburzona...
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublicationIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
Chapter 2: Modelling and analysis of rotor with magnetic bearing system
PublicationThe paper is concerned with rotor magnetic bearing system modelling. Such system is a relatively complex electromechanical system and can be considered as typical mechatronic one. The port-based modelling of physical systems has been used to obtain discrete-continuous model of considered system. Proposed approach enables to obtain reduced low-order lumped parameter representation of the system including gyroscopic interactions....
-
Impulsive lubrication of hip joint for hypo-elastic cartilage model
PublicationPraca rozwiązuje problem smarowania stawu biodrowego człowieka w warunkach niestacjonarnych z uwzględnieniem hypo-sprężystych (pod-sprężystych) właściwości odkształcalnej szkieletu chrząstki stawowej. Prezentowane są rozkłady wartości ciśnienia hydrodynamicznego oraz zmienne w czasie rozkłady wartości sił nośnych.
-
Periodic and impulsive lubrication of hip joint with stochastic rough surface.
PublicationNiniejsza praca przedstawia porównanie wartości nośności uzyskanych numerycznie dla niestacjonarnego smarowania impulsywnego oraz niestacjonarnego smarowania periodycznego sferycznego stawu biodrowego człowieka. W obu przypadkach przyjęto, że smarująca ciecz synowialna ma własności lepkosprężyste a występy chropowatych powierzchni chrząstki stawowej zmieniają się losowo. Charakterystyki zmiennych w czasie rozkładów wartości ciśnienia...
-
In vivoevaluation of the CB1allosteric modulator LDK1258 reveals CB1-receptor independent behavioral effects
PublicationIn the present study, we examined whether LDK1258, which produces strong CB1receptor allosteric effects ininvitroassays, would elicitin vivoeffects consistent with allosteric activity. In initial studies, LDK1258 reducedfood consumption and elicited delayed antinociceptive effects in the chronic constrictive injury of the sciaticnerve (CCI) model of neuropathic pain, which unexpectedly emerged 4 h post-injection. UPLC-MS/MS analysisquantified...
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublicationPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
Bioaugmentation of a sequencing batch reactor with Archaea for the treatment of reject water
PublicationIn this study, the bioaugmentation of a sequencing batch reactor (SBR) for the treatment of reject water from wastewater treatment plant was evaluated. For the bioaugmentation step a product containing an enrichment of microorganisms from the Archaea domain was used to enhance the performance of the reactor for treating reject water. The experiment was carried out in two parallel lab-scale sequencing batch reactors. The first one...
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublicationThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Degradation of 1,4-dioxane by sono-activated persulfates for water and wastewater treatment applications
PublicationThis paper presents a hybrid advanced oxidation process (AOP) based on sonocavitational activation of persulfate (PS) for degradation of 1,4-dioxane during wastewater treatment. Application of sono-cavitation effectively convert PS to radical species demonstrating synergistic effect by increasing the reaction rate and reducing the required energy for activation. It is economically feasible and deployed alternative to the direct...
-
Simplified Numerical Model for Transient Flow of Slurries at Low Concentration
PublicationRapid transients are particularly dangerous in industrial hydro-transport systems, where solid-liquid mixtures are transported via long pressure pipelines. A mathematical description of such flow is difficult due to the complexity of phenomena and difficulties in determining parameters. The main aim of the study was to examine the influence of the simplified mixture density and wave celerity description on satisfactory reproduction...
-
Evaluation of expanded uncertainty of instantaneous power measurement in a bearing diagnostic system.
PublicationThe paper presents the issues concerning the estimation of the expanded uncertainty in the system for the diagnosis of rolling bearings, consisting of transducers: voltage and current voltage, which is used for diagnostic bearing motors method based on the measurement and analysis of the instantaneous power signal consumed by the induction motor. It presents the methodology for assessing the measurement uncertainty and presents...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublicationNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Numerical simulation of screw displacement pile interaction with non-cohesive soil
PublicationA trial numerical simulation of screw displacement pile interaction with non-cohesive subsoil during the transfer of compression load. The simulation was carried out in an axisymmetric system. The technological phases of pile installation in the ground were numerically modelled using equivalent processes which provided similar effects to real technical actions. The results of the numerical calculations were verified by comparing...
-
TIME-DOMAIN NUMERICAL EVALUATION OF SHIP RESISTANCE AND MOTION IN REGULAR WAVES BY USING THE CFD URANS METHOD
PublicationTaking into account the International Maritime Organisation’s (IMO) strategy to radically reduce the GHG emitted by the shipping industry towards zero emission operation, today's assessment of ship behaviour in waves, its seakeeping characteristics and resistance and their interrelation with fuel consumption and emissions are one of the most attended research subject. There are three methods to conduct this analysis, which are...
-
Joint experimental and theoretical study on low-energy elastic electron scattering by gaseous alkynes: Differential cross sections, shape resonances, and methylation effects
PublicationA detailed comparison of experimental and theoretical elastic cross sections for low-energy electron scattering by ethyne, taken earlier in our group by Gauf et al. [Phys. Rev. A 87, 012710 (2013)], and some of its methylated derivatives, propyne, and the isomers 1-butyne and 2-butyne, taken here, are presented. The present differential cross sections were measured at incident electron energies ranging from 1 eV to 30 eV and...
-
Synthesis and thermal studies of flexible polyurethane nanocomposite foams obtained using nanoclay modified with flame retardant compound
PublicationThis work presents thermal studies of nanocomposites based on the flexible polyurethane (PU) matrix and filled using montmorillonite organically modified with organophosphorus flame retardant compound. Flexible PU nanocomposite foams were prepared in the reaction carried out between reactive alcoholic hydroxyl and isocyanate groups with the ratio of NCO to OH groups equal to 1.05. The amount of an organoclay ranging from 3 to 9...
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublicationThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Discrete simulations of a triaxial compression test for sand by DEM.
PublicationArtykuł przedstawia wyniki symulacji dyskretnych dla ściskania trójosiowego stosując metodę elementów dyskretnych DEM. Symulacje wykonano dla piasku. Zastosowano kuli z momentami kontaktu do symulacji kształtu ziaren. Przeprowadzono analizy dla różnych zmiennych parametrów: średnica piasku, krzywa uziarnienia, kształt ziaren, wymiary próbki i warunki brzegowe.
-
From U2TP Models to Executable Tests with TTCN-3
PublicationThe approach towards system engineering according to Model-Driven Architectures (MDA) with code generation derived from model implies also an increased need for research on automation of the test generation process. This paper presents an approach to derive executable tests from UML 2.0 Testing Profile diagrams automatically. In particular, an approach to derive executable tests within the Testing and Test Control Notation (TTCN-3)...
-
A COMPARISON OF WEAR PROPERTIES OF WATER LUBRICATED NBR AND PTFE SLIDING BEARINGS
PublicationThe excessive wear of a journal shaft can be caused by many factors, for example, working conditions (e.g., temperaturę, slip speed, the type of lubricant), pressure, the type of material used on the bearings and shafts and their roughness, as well as contamination remaining in the system. This paper presents the roughness profiles co-operating with a rubber (NBR) and polytetrafluoroethylene (PTFE) bushes. The conditions of cooperation...
-
Experimental ORC micro-power plant for CHP application Part B: Radial and Multi-stage axial turbines
PublicationThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. Special attention is paid to a micro-turbine which was built and tested in two variants: a radial turbine and an axial turbine. A concept of a radial turbine with 2 centripetal and 2 centrifugal stages is shown. This prototype was equipped with an aerostatic gas bearing and, alternatively, with...
-
Solubility of Methane in Water: Some Useful Results for Hydrate Nucleation
PublicationIn this paper, the solubility of methane in water along the 400 bar isobar is determined by computer simulations using the TIP4P/Ice force field for water and a simple LJ model for methane. In particular, the solubility of methane in water when in contact with the gas phase and the solubility of methane in water when in contact with the hydrate has been determined. The solubility of methane in a gas–liquid system decreases as temperature...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublicationFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Detection and Model of Thermal Traces Left after Aggressive Behavior of Laboratory Rodents
PublicationAutomation of complex social behavior analysis of experimental animals would allow for faster, more accurate and reliable research results in many biological, pharmacological, and medical fields. However, there are behaviors that are not only difficult to detect for the computer, but also for the human observer. Here, we present an analysis of the method for identifying aggressive behavior in thermal images by detecting traces...
-
Numerical Analysis of Impact of Energy Buoy Anchoring Configurations on its Motion and Efficiency
PublicationThis paper presents a numerical analysis of the impact of energy buoy mooring configurations on its movement on the wave and effectiveness. The method used to analyse the buoy movement modelling in six degrees of freedom was described in a paper presented at the Conference 2011. Simulations of the buoy movement in regular wave and power calculations were conducted for several configurations of anchoring systems and position of...
-
The use of GFRP tubes as load-bearing jackets in concrete-composite columns
PublicationThe paper presents the fields of applications of polymer composites in building structures. The use of composite glass fibre tubes is discussed in more detail. The laboratory methods used to test the mechanical properties of these pipes are presented. An original research program is presented, including six concrete-filled glass fibre tubes. The cylinders and columns made in this way were tested for their axial load capacity. Conclusions...
-
TESTING CONTRACTION AND THERMAL EXPANSION COEFFICIENT OF CONSTRUCTION AND MOULDING POLYMER COMPOSITES
PublicationThe paper presents results of systematic tests of contraction and thermal expansion coefficients of materials based on polymer composites. The information on the above material properties is essential both at the design stage and during the use of finished products. Components for the samples were selected in such a way as to represent typical materials used for production of construction and moulding elements. The performed tests...
-
Numerical Simulation of Catastrophic Flood: the Case Study of Hypothetical Failure of the Bielkowo Hydro–Power Plant Reservoir
PublicationThe numerical modeling of flood wave propagation following the hypo-thetical breaks of the embankments of the Bielkowo hydro–power plant storage reservoir (Kolbudy II Reservoir) on the Radunia River in Poland have been presented. The results of computations were used to estimate the parameters of the flood waves, which are indispensable for the flood zone determination and mapping and then for the flood risk analysis. When estimating...
-
Deterioration of masonry structure investigated by a thermal camera with a qualitative assessment of thermal image processing
PublicationThermal imaging is contemporary remote sensing measurement technique, which provides an image of the temperature distribution in the measured object. The method is widely used, due to its mobility as well as the non-destructive character of the measurement. Infrared thermography is especially relevant in the inspection of insulation, what is more, it is a suitable device for detecting thermal bridges and structural changes, which...
-
MODELING THE pH EFFECTS ON NITROGEN REMOVAL IN THE ANAMMOX-ENRICHED GRANULAR SLUDGE
PublicationThe aim of the study was to determine the pH effects on nitrogen removal in the anammox-enriched 10 granular sludge. The experimental data were extracted from a 4L completely-mixed batch reactor with the 11 granular sludge at different initial pH values (6.5, 7, 7.5, 8, 8.5, 9, 9.5, 10, 10.5) and constant temperature 12 T=30℃. Simulations were run in GPS-X 6.4 using a comprehensive mechanistic model Mantis2. Two 13 kinetic parameters,...
-
Verification of the criteria for evaluation of water and frost resistance of asphalt concrete
PublicationThe paper presents the results of field investigation - condition survey of existing pavements and the results of laboratory tests on water and frost resistance of samples cored from the these pavements. The purpose of testing was to verify the criteria for evaluation of the resistance of asphalt concrete to the action of water and frost by way of comparing the results of field and laboratory tests, followed by evaluation of their...
-
Pore Water Pressure Development in Soft Soil due to Installation and Loading of Controlled Modulus Columns
PublicationExcess pore water pressure (EPWP) development and decay due to the installation and static loading tests of controlled modulus columns (CMC) in soft soil was measured with piezometers equipped with low air entry (LAE) filters and a piezocone (CPTU) equipped with a high air entry (HAE) filter. The HAE filter allows for detailed detection of EPWP in short time intervals during construction of CMC. The influence zone due to the installation...
-
Thermal visualization of Ostwald-de Waele liquid in wavy trapezoidal cavity: Effect of undulation and amplitude
PublicationThe present study is concerned with the numerical simulations of Ostwald-de Waele fluid flow in a wavy trapezoidal cavity in the presence of a heated cylinder situated at the center of the cavity. The work consists in characterizing the mixed convection as a function of the intensity of heat flow. The flow behaviour and temperature distribution in a cavity are the main focus of this study. The lower wall of the cavity is fixed...
-
Small Vessel with Inboard Engine Retrofitting Concepts; Real Boat Tests, Laboratory Hybrid Drive Tests and Theoretical Studies
PublicationThe development of modern technologies and their increasing availability, as well as the falling costs of highly ecient propulsion systems and power sources, have resulted in electric or hybrid propulsions systems’ growing popularity for use on watercraft. Presented in the paper are design and lab tests of a prototype parallel hybrid propulsion system. It describes a concept of retrofitting a conventionally powered nine meter-long...
-
THE INFLUENCE OF WATER AND MINERAL OIL ON MECHANICAL LOSSES IN THE DISPLACEMENT PUMP FOR OFFSHORE AND MARINE APPLICATIONS
PublicationIn this paper mechanical losses in a positive displacement pump supplied with water and mineral oil (two liquids having significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a special design (prototype) of a satellite pump. The design of the satellite pump is presented in the article. The pump features a non-circular tooth working mechanism. This pump...
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublicationDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
Impact of thermal backfill parameters on current-carrying capacity of power cables installed in the ground
PublicationProper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity...
-
Antenna Modeling Using Variable-Fidelity EM Simulations and Constrained Co-Kriging
PublicationUtilization of fast surrogate models has become a viable alternative to direct handling of fullwave electromagnetic (EM) simulations in EM-driven design. Their purpose is to alleviate the difficulties related to high computational cost of multiple simulations required by the common numerical procedures such as parametric optimization or uncertainty quantification. Yet, conventional data-driven (or approximation) modeling techniques...
-
Developing Methodology for Model Tests of Floating Platforms in Low -Depth Towing Tank
PublicationThe paper presents two different methods of physical modeling of semi-submersible platform mooring system for research in low depth towing tank. The tested model was made in the scale of 1:100 resembling the "Thunder Horse" platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced starshape and attached at the bottom to suction piles. The tests...
-
Experimental and first-principles studies of high-pressure effects on the structural, electronic, and optical properties of semiconductors and lanthanide doped solids
Publication -
Defining the thermal conductivity of thermally heterogeneous hollow wall bricks used as elements for increasing the comfort of buildings
PublicationThe article presents numerical calculation analysis in the scope of determining thermal conductivity coefficientλeq[W/(m·K)] of thermally heterogeneous hollow bricks of thermally heterogeneous structure (a combinationof structural material with thermal insulation material). Numerical calculations were conducted by means ofprofessional software TRISCO-KOBRU 86, serving thermal circulation analysis in a 2D field in stationary approach.The...
-
On thermal stability of piezo-flexomagnetic microbeams considering different temperature distributions
PublicationBy relying on the Euler–Bernoulli beam model and energy variational formula, we indicate critical temperature causes in the buckling of piezo-flexomagnetic microscale beams. The corresponding size-dependent approach is underlying as a second strain gradient theory. Small deformations of elastic solids are assessed, and the mathematical discussion is linear. Regardless of the pyromagnetic effects, the thermal loading of the thermal...
-
Preliminary experimental research on stability of truss' joint with positive eccentricity
PublicationRecently, a very large interest in lightweight steel structures made from cold-formed sections has been noticeable. In the design practice, a large emphasis is put on rational shaping of both the thin-walled elements and constructions designed on them. The aim of this paper is to present the methodology for preparation of experimental research that model the behaviour of members in trusses made of cold-formed sections with positive...