Filters
total: 2051
filtered: 1790
displaying 1000 best results Help
Search results for: MATERIAL AND ENERGY FLOW ANALYSIS
-
Probabilistic Methods in Reliability Assessment of Engineering Lightweight Structures
PublicationThe paper considers the probability-based analysis of structural safety measures. Two different numerical examples of representative lightweight structures are considered – a submerged truss tower supporting an offshore platform, and an overhead power line support truss tower. On the basis of these examples, the importance of a motivated selection of analysis method and a proper choice of the number of important variables is shown....
-
Sensitivity analysis of free torsional vibration frequencies of thin-walled laminated beams under axial load
PublicationThe paper addresses sensitivity analysis of free torsional vibration frequencies of thin-walled beams of bisymmetric open cross-section made of unidirectional fibre-reinforced laminate. The warping effect and the axial end load are taken into account. The consideration is based upon the classical theory of thin-walled beams of non-deformable cross-section. The first-order sensitivity variation of the frequencies is derived with...
-
On the current state of dovetail wall-corner joints in wooden Greek Catholic churches in Polish Subcarpathia with structural and sensitivity analyses
PublicationThis paper describes the current condition of some dovetail joints which form the wall corners of two Greek Catholic churches of wooden construction in Polish Subcarpathia. It also gives the historical background of the sacral architecture of that region. The two structures, which represent the same type of log corner joints are situated in Chotylub and Cewków. The buildings were examined e.g. for damage, wood moisture content,...
-
Preparation and characterisation of iron substituted Mn1.7Cu1.3-xFexO4 spinel oxides (x = 0, 0.1, 0.3, 0.5)
PublicationSpinel oxides with the general formula Mn1.7Cu1.3-xFexO4 (x= 0, 0.1, 0.3, 0.5) were prepared and evaluated in this work for their properties at high temperatures. The effect of partially substituting Cu by Fe has not been studied so far for this group of materials and is thus evaluated in this work. Mn1.7Cu1.3-xFexO4 powders were synthesised by a soft chemistry process and studied in terms of crystallographic phase analysis, electrical...
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublicationUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
The advanced monitoring as a key factor for appropriate optimization and control of full-scale activated sludge systems – case study Debogorze WWTP.
PublicationComputer simulation has become a helpful tool in wastewater treatment systems performance and effectiveness analysis. Advanced monitoring, by using appropriate software, enables to create a mathematical model of a real wastewater treatment plant (WWTP), run a simulation and subsequently interpret results under various conditions. An operation of WWTP is usually controlled by global parameters such as flow, solids retention time,...
-
Fermentative Conversion of Two-Step Pre-Treated Lignocellulosic Biomass to Hydrogen
PublicationFermentative hydrogen production via dark fermentation with the application of lignocellulosic biomass requires a multistep pre-treatment procedure, due to the complexed structure of the raw material. Hence, the comparison of the hydrogen productivity potential of different lignocellulosic materials (LCMs) in relation to the lignocellulosic biomass composition is often considered as an interesting field of research. In this study,...
-
Multi-source-supplied parallel hybrid propulsion of the inland passenger ship STA.H. Research work on energy efficiency of a hybrid propulsion system operating in the electric motor drive mode
PublicationIn the Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology, design has recently been developed of a small inland ship with hybrid propulsion and supply system. The ship will be propelled by a specially designed so called parallel hybrid propulsion system. The work was aimed at carrying out the energy efficiency analysis of a hybrid propulsion system operating in the electric motor drive mode and at...
-
Analysis of Agricultural and Engineering Systems using Simulation Decomposition
PublicationThis paper focuses on the analysis of agricultural and engineering processes using simulation decomposition (SD). SD is a technique that utilizes Monte Carlo simulations and distribution decomposition to visually evaluate the source and the outcome of different portions of data. Here, SD is applied to three distinct processes: a model problem, a nondestructive evaluation testing system, and an agricultural food-water energy system....
-
Anti-plane waves in an elastic thin strip with surface energy
PublicationWe consider anti-plane motions of an elastic plate taking into account surface energy within the linear Gurtin–Murdoch surface elasticity. Two boundary-value problems are considered that describe complete shear dynamics of a plate with free faces or with free and clamped faces, respectively. These problems correspond to anti-plane dynamics of an elastic film perfectly or non-perfectly attached to a rigid substrate. Detailed analysis...
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublicationThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...
-
Variable-fidelity response feature surrogates for accelerated statistical analysis and yield estimation of compact microwave components
PublicationAccounting for manufacturing tolerances is an essential part of a reliable microwave design process. Yet, quantification of geometry and/or material parameter uncertainties is challenging at the level of full-wave electromagnetic (EM) simulation models. This is due to inherently high cost of EM analysis and massive simulations necessary to conduct the statistical analysis. Here, a low-cost and accurate yield estimation procedure...
-
Effective Formula for Impact Damping Ratio for Simulation of Earthquake-induced Structural Pounding
PublicationStructural pounding during earthquakes may cause substantial damage to colliding structures. The phenomenon is numerically studied using different models of collisions. The aim of the present paper is to propose an effective formula for the impact damping ratio, as a parameter of the impact force model used to study different problems of structural pounding under seismic excitations. Its accuracy has been verified by four various...
-
Disturbances of magnetic field in surrounding of mobile, metalic plate
PublicationThe uniform magnetic field of the Earth in the surrounding of a mobile, metalic object undergoes deformation by eddy currents. The influence of the moving conducting object on total magnetic field of the Earth depends on the object's shape, position and speed of the changes relative to the magnetic field's vector of the Earth as well as the electric conductivity and the relative magnetic permeability of the material. The disturbances...
-
The project of pull system for storehouse and production line in a company provides electronics
PublicationThe chapter below presents how to reduced delivery of the material to production by using a "Kanban schedule board" and related tools from 48 hours and 59 minutes to 41 minutes in a company provides electronics. The solution was found through analysis of the current way of supplying stands and using Just In Time idea, the reduction of ''muda''. To solve the problem was used Kanban card", which has the shape of two triangles joined...
-
Tunable Dielectric Switching of (Quinuclidinium)[MnCl4] Hybrid Compounds
PublicationInorganic−organic hybrid QMnCl (Q = quinuclidinium) crystals were synthesized and characterized. The X-ray and variable-temperature IR/Raman analysis demonstrate that the crystals undergo a reversible structural phase transition, which originates from an order−disorder process and is related to the dynamics of the organic Q cation. Dielectric function measurements disclose a switchability between low (“OFF”) and high (“ON”) dielectric...
-
Geometrically Nonlinear Analysis of Functionally Graded Shells Based on 2-D Cosserat Constitutive Model
PublicationIn this paper geometrically nonlinear analysis of functionally graded shells in 6-parameter shell theory is presented. It is assumed that the shell consists of two constituents: ceramic and metal. The mechanical properties are graded through the thickness and are described by power law distribution. Formulation based on 2-D Cosserat constitutive model is used to derive constitutive relation for functionally graded shells. Numerical...
-
An Ultra-Low-Energy Analog Comparator for A/D Converters in CMOS Image Sensors
PublicationThis paper proposes a new solution of an ultra-low-energy analog comparator, dedicated to slope analog-to-digital converters (ADC), particularly suited for CMOS image sensors (CISs) featuring a large number of ADCs. For massively parallel imaging arrays, this number may be as high as tens-hundreds of thousands ADCs. As each ADC includes an analog comparator, the number of these comparators in CIS is always high. Detailed analysis...
-
Computer Simulation in Predicting Biochemical Processes and Energy Balance at WWTPs
PublicationNowadays, the use of mathematical models and computer simulation allow analysis of many different technological solutions as well as testing various scenarios in a short time and at low financial budget in order to simulate the scenario under typical conditions for the real system and help to find the best solution in design or operation process. The aim of the study was to evaluate different concepts of biochemical processes and...
-
Low temperature broad band dielectric spectroscopy of multiferroic Bi6Fe2Ti3O18 ceramics
PublicationIn the present research the tool of broadband dielectric spectroscopy was utilized to characterize dielectric behavior of Bi6Fe2Ti3O18 (BFTO) Aurivillius-type multiferroic ceramics. Dielectric response of BFTO ceramics was studied in the frequency domain (Δν=0.1Hz – 10MHz) within the temperature range ΔT=-100°C – 200°C. The Kramers-Kronig data validation test was employed to validate the impedance data measurements and it was found...
-
Conversion of waste biomass into activated carbon and evaluation of environmental consequences using life cycle assessment
PublicationIn this article, activated carbon was produced from Lantana camara and olive trees by H3PO4 chemical activation. The prepared activated carbons were analyzed by characterizations such as scanning electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller, X-ray diffraction, thermogravimetric analysis, and Fourier transform infrared spectroscopy. H3PO4 is used as an activator agent to create an abundant pore...
-
A novel approach for processing CaAlSiON glass-ceramics by spark plasma sintering: Mechanical and electrical properties
PublicationLithium containing glassy materials can be used as solid electrolytes or electrode materials for lithium-ion batteries due to their high energy density. Conventional melt-quenched Ca11Al14Si16O49N10 glass powder containing 24 e/o N, doped with Li-ions (1, 3, and 6 wt. %) and sintered by spark plasma sintering technique (SPS) was studied. The benefits of using SPS to produce glass-ceramics are rapid heating rates compared to conventional...
-
Revitalization of Residential Buildings Dating Back to the Late19th and Early 20th Century on the Example of “Willa Halina” in Sopot (Poland)
PublicationResidential buildings dating back to the late 19th and early 20th century constitute an important element of the urban composition of many European cities, often determining their overall spatial expression. These buildings often require revitalization and sometimes also reconstruction or extension. Such activities make it possible to restore historical buildings to their former glory, but also to create new architecture, inscribed...
-
Effective Permeability of Multi Air Gap Ferrite Core 3-Phase Medium Frequency Transformer in Isolated DC-DC Converters
PublicationThe magnetizing inductance of the medium frequency transformer (MFT) impacts the performance of the isolated dc-dc power converters. The ferrite material is considered for high power transformers but it requires an assembly of type “I” cores resulting in a multi air gap structure of the magnetic core. The authors claim that the multiple air gaps are randomly distributed and that the average air gap length is unpredictable at the...
-
Laser Beam as a Precision Tool to Increase Fatigue Resistance in an Eyelet of Undercarriage Drag Strut
PublicationThe article contains the results of tests on a laser-processed eyelet of undercarriage drag strut to increase its fatigue strength. Laser processing concentrated on both sides around the hole of eye for connecting the undercarriage drag strut caused that the material in this area withstood more than twice the number of load cycles established for this material. In order to determine the reasons for the increase in fatigue strength,...
-
Design analysis of combined gas-vapour micro power plant with 30 kW air turbine
PublicationThe article presents basic results of the design analysis of a combined gas-vapour micro power plant with a waste-heat boiler without exhaust reheat, working in the vapour section in the Organic Rankine Cycle (ORC) system. The analysis concerned working media most frequently used in those types of power plants and planned to be used in future. The object of the analysis was a micro power plant with a 30 kW gas (air) turbine for...
-
Design analysis of combined gas-vapour micro power plant with 30 kW air turbine
PublicationThe article presents basic results of the design analysis of a combined gas-vapour micro power plant with a waste-heat boiler without exhaust reheat, working in the vapour section in the Organic Rankine Cycle (ORC) system. The analysis concerned working media most frequently used in those types of power plants and planned to be used in future. The object of the analysis was a micro power plant with a 30 kW gas (air) turbine for...
-
Heat transfer characteristics of hybrid microjet -microchannel cooling module
PublicationThe paper presents the experimental investigation of heat transfer intensification in a microjet- microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublicationA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
High-efficiency mini and micro heat exchangers for dispersed power generation
PublicationTaking into account the dispersed systems technologies and their development, the ORC systems seem to be promising technology amongst various micro-CHP domestic units (electrical power production below 10 kWe), however practical realization of the ORC cycle in a micro-scale is technically challenging. The system consists in devices such as the vapour generation unit (boiler), expansion device and heat exchangers. Each of them should...
-
On the generalized model of shell structures with functional cross-sections
PublicationIn the present study, a single general formulation has been presented for the analysis of various shell-shaped structures. The proposed model is comprehensive and a variety of theories can be used based on it. The cross-section of the shell structure can be arbitrarily analyzed with the presented equations. In other words, various types of shell structures, including cylindrical, conical, spherical, elliptical, hyperbolic, parabolic,...
-
Biowodór, „paliwo przyszłości”, dotychczasowe metody otrzymywania , porównanie metod otrzymywania
PublicationWodór jest ważnym pierwiastkiem w przemyśle chemicznym. Biowodór wydaje się być użytecznym odnawialnym nośnikiem energii, który mógłby zastąpić paliwa kopalne. Największym problemem wodoru jest jego rzadkie występowanie w czystej formie molekularnej H 2 . Dlatego otrzymanie biowodoru w objętościach opłacalnych ja ko surowiec czy biopaliwo wiedzie przez bioodpady „przesycone” wodorem. Każdy związek...
-
Chemical, thermal and laser processes in recycling of photovoltaic silicon solar cells and modules
PublicationIn recent years, photovoltaic power generation systems have been gaining unprecedented attention as an environmentally beneficial method to solve the energy problem. From the economic point of view the pure silicon, which can be recapture from the used cells, is the most important material due to its cost and shortage. In the paper selected methods of used or damaged module and cells recycling and experimental results are presented....
-
Zirconia ceramics with additions of Alumina for advanced tribological and biomedical applications
PublicationThe results of an investigation on slip cast and sintered Y2O3 (3 wt%)- stabilized ZrO2 with additions of 5, 10, 15 wt% Al2O3 are reported. The surface roughness, porosity and density of the samples were measured. The hardness HRc and Hv, fracture toughness K1C, and friction coefficients were also measured using standard methods. The structural properties of the samples were observed by Scanning Electron Microscopy (SEM). The surface...
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublicationSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublicationLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Validated HPTLC method for determination of ledol and alloaromadendrene in the essential oil fractions of Rhododendron tomentosum plants and in vitro cultures and bioautography for their activity screening
PublicationRhododendron tomentosum (Ledum palustre) is a bog shrub used in traditional medicine for treatment of respiratory and rheumatic diseases. Due to the large variability of the chemical composition of its essential oil, depending on the habitat, the in vitro cultures were established as the alternative source of the volatile fraction. There is a need to monitor a quality of the field grown as well as in vitro plant material, especially...
-
Historical carpentry corner log joints—Numerical analysis within stochastic framework
PublicationThe paper presents the results of numerical analysis performed on historical, traditional carpentry corner logjoints of two basic topologies: the short-corner dovetail connection and the saddle notch connection. These types of carpentry joints are commonly used in currently preserved objects of wooden architecture. All connections have been modelled in pinewood, which has been defined in the Finite Element software MSC.Marc/Mentat...
-
Mathematical approach to design 3D scaffolds for the 3D printable bone implant
PublicationThis work demonstrates that an artificial scaffold structure can be designed to exhibit mechanical properties close to the ones of real bone tissue, thus highly reducing the stress-shielding phenomenon. In this study the scan of lumbar vertebra fragment was reproduced to create a numerical 3D model (this model was called the reference bone sample). New nine 3D scaffold samples were designed and their numerical models were created....
-
Assessment of the technological reliability of a hybrid constructed wetland for wastewater treatment in a mountain eco-tourist farm in Poland
PublicationThe aim of the present study was to assess the technological reliability of a domestic hybrid wastewater treatment installation consisting of a classic three-chambered (volume 6 m3) septic tank, a vertical flow trickling bed filled with granules of a calcinated clay material (KERAMZYT), a special wetland bed constructed on a slope, and a permeable pond used as a receiver. The test treatment plant was located at a mountain eco-tourist...
-
The Motion Analysis of Attacus Atlas Rigid Wing
PublicationThe remarkable aerodynamic efficiency of flapping insect wings has fascinated researchers for many years. Butterfly wings are distinguished by a much larger lifting surface, and thus, a different style of flapping flight. The considerations described in the article are an introduction to a fully flexible analysis of the wing in motion. The study of the rigid wing gives the basic knowledge necessary in the further process. The yaw,...
-
Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder
PublicationInvestigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry),...
-
Experimental and numerical analysis of the pyrolysis dynamics of a single wood particle: presentation of the radiographic technique
PublicationPyrolysis is an oxygen-free process for the thermal decomposition of raw materials. The heat conduction and flow of pyrolysis products (i.e., the gas fraction and liquid vapour generated during pyrolysis) influence the process and products. In this work, the influence of the orientation of wooden particle fibres with respect to the direction of the heat source on the dynamics of the process was investigated, where there were two...
-
Review of methods for assessing traffic conditions on basic motorway and expressway sections
PublicationMotorways and expressways are the core of each country’s road system. Road planning, design and management requires tools to ensure that roads have the right geometry, traffic layout and equipment. These include methods for capacity estimation and assessing traffic conditions. Because the paper focusses on the basic segments of motorways and expressways (sections located between interchanges and outside of their influence), its...
-
Experimental investigations on adiabatic frictional pressure drops of R134a during flow in 5mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg/m2 s. The frictional pressure drop was characterized for the refrigerant R134a, for vapor qualities ranging from 0 to 1. Long-time thermal stability of test facility allowed to gather...
-
Fully scalable one-pot method for the production of phosphonic graphene derivatives
PublicationGraphene oxide was functionalized with simultaneous reduction to produce phosphonated reduced graphene oxide in a novel, fully scalable, one-pot method. The phosphonic derivative of graphene was obtained through the reaction of graphene oxide with phosphorus trichloride in water. The newly synthesized reduced graphene oxide derivative was fully characterized by using spectroscopic methods along with thermal analysis. The morphology...
-
Investigation of the aerodynamics of an innovative verticalaxis wind turbine
PublicationThis paper presents a preliminary three dimensional analysis of the transient aerodynamic phenomena occurring in the innovative modification of classic Savonius wind turbine. An attempt to explain the increased efficiency of the innovative design in comparison with the traditional solution is undertaken. Several vorticity measures such as enstrophy, absolute helicity and the integral of the velocity gradient tensor second invariant...
-
A continual model of a damaged medium used for analyzing fatigue life of polycrystalline structural alloys under thermal–mechanical loading
PublicationThe main physical laws of thermal–plastic deformation and fatigue damage accumulation processes in polycrystalline structural alloys under various regimes of cyclic thermal–mechanical loading are considered. Within the framework of mechanics of damaged media, a mathematical model is developed that describes thermal–plastic deformation and fatigue damage accumulation processes under low-cycle loading. The model consists of three...
-
Eco-friendly Route for Thermoplastic Polyurethane Elastomers with Bio-based Hard Segments Composed of Bio-glycol and Mixtures of Aromatic–Aliphatic and Aliphatic–Aliphatic Diisocyanate
PublicationApplication of bio-based diisocyanates with low volatility instead petrochemical diisocyanates has positive impact on environment by reduction of hazardous effects on living organisms and lead to bio-based polyurethanes (bio-PUs) with good usage properties. This work was focused on the synthesis and chosen properties examination of partially bio-based thermoplastic polyurethane elastomers (bio-PUs) obtained using diisocyanate mixtures,...
-
Recycling of photovoltaic modules - legal status, technology, market prospects
PublicationThe increase in the number of manufactured and installed photovoltaic modules and the growing concern about the insufficient supply of pure silicon imply the need to take action to develop infrastructure for recycling PV modules. The article presents a multifaceted analysis of the current state of development of the photovoltaic module recycling sector from a global and national perspective. The essence of the issue was introduced...