Filters
total: 2685
filtered: 1947
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: railway line capacity
-
EM-Driven Multi-Objective Design of Impedance Transformers By Pareto Ranking Bisection Algorithm
PublicationIn the paper, the problem of fast multi-objective optimization of compact impedance matching transformers is addressed by utilizing a novel Pareto ranking bisection algorithm. It approximates the Pareto front by dividing line segments connecting the designs found in the previous iterations, and refining the obtained candidate solutions by means of poll-type search involving Pareto ranking. The final Pareto set is obtained using...
-
Estimation of a single balun parameters on the base of back-to-back measurements
PublicationA method of estimation of a single balun S parameters based on the measured parameters of back-to-back configuration is presented in the paper. Proposed approach is to measure two back-to-back circuits: i) direct connection of baluns and ii) connection with additional transmission line segment between the baluns. Coupling effects in both circuits are calculated from full-wave simulations. Next they are applied to estimate the parameters...
-
A testing method of analog parts of mixed-signal electronic systems equipped with the IEEE1149.1 test bus
PublicationA new solution of the JTAG BIST for testing analog circuits in mixed-signal electronic microsystems controlled by microcontrollers and equipped with the IEEE1149.1 bus is presented. It is based on a new fault diagnosis method in which an analog circuit is stimulated by a buffered signal from the TMS line, and the time response of the circuit to this signal is sampled by the ADC equipped with the JTAG. The method can be used for...
-
In Vitro Studies on Nanoporous, Nanotubular and Nanosponge-Like Titania Coatings, with the Use of Adipose-Derived Stem Cells
PublicationIn vitro biological research on a group of amorphous titania coatings of different nanoarchitectures (nanoporous, nanotubular, and nanosponge-like) produced on the surface of Ti6Al4V alloy samples have been carried out, aimed at assessing their ability to interact with adipose-derived mesenchymal stem cells (ADSCs) and affect their activity. The attention has been drawn to the influence of surface coating architecture and its physicochemical...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublicationTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
BPL-PLC Voice Communication System for the Oil and Mining Industry
PublicationApplication of a high-efficiency voice communication systems based on broadband over power line-power line communication (BPL-PLC) technology in medium voltage networks, including hazardous areas (like the oil and mining industry), as a redundant mean of wired communication (apart from traditional fiber optics and electrical wires) can be beneficial. Due to the possibility of utilizing existing electrical infrastructure, it can...
-
Novel molecules containing structural features of NSAIDs and 1,2,3-triazole ring: Design, synthesis and evaluation as potential cytotoxic agents
PublicationFor the first time the template containing structural features of more than one NSAIDs and the 1,2,3-triazole ring was explored for the identification of potential cytotoxic agents. These new and complex molecules were predicted to be effective inhibitors of PDE4B by molecular modelling studies in silico. The multi-step synthesis of these compounds were carried out starting from the well-known drug nimesulide and involved the use...
-
Surrogate-assisted EM-driven miniaturization of wideband microwave couplers by means of co-simulation low-fidelity models
PublicationThis article proposes a methodology for rapid design optimization of miniaturized wideband couplers. More specifically, a class of circuits is considered, in which conventional transmission lines are replaced by their abbreviated counterparts referred to as slow-wave compact cells. Our focus is on explicit reduction of the structure size as well as on reducing the CPU cost of the design process. For the sake of computational feasibility,...
-
Structure, Physicochemical and Biological Properties of an Aqua (2,2′,2′′-Nitrilotriacetato)-oxidovanadium(IV) Salt with 4-Methylpyridinium Cation
PublicationThe crystal structure of a nitrilotriacetate (nta) oxidovanadi-um(IV) salt with 4-methylpyridinium cation, [4-Me(Py)H]+, of [4-Me(Py)H][VO(nta)(H2O)] stoichiometry was determined. The com-plex comprises a discrete mononuclear [VO(nta)(H2O)]–coordinationentity that can be rarely found among other known compounds con-taining nitrilotriacetate oxidovanadium(IV) moieties. The complex wascharacterized by spectroscopic (IR and EPR) methods,...
-
Ekonomiczne aspekty zastosowania techniki Mobilnych Pomiarów Satelitarnych przy regulacji osi toru
PublicationOd 2009 roku interdyscyplinarny zespół naukowy Politechniki Gdańskiej i Akademii Marynarki Wojennej (a obecnie Akademii Morskiej w Gdyni) rozwija technikę Mobilnych Pomiarów Satelitarnych toru kolejowego. Technika ta polega na objeździe trasy ciągnikiem szynowym z przyczepą (wagonem-platformą) lub wózkami, z zainstalowanymi na tych pojazdach odbiornikami sygnałów satelitarnych. Umożliwia ona precyzyjne określenie współrzędnych...
-
Modelowanie kratownicy z kształtowników giętych na zimno z mimośrodami dodatnimi w węźle = Modelling of truss with cold-formed section and positive eccentricyty in the node.
PublicationThe topic of this research is establishing load-carrying capacity of compressed and tensed chords of trusses made of cold-formed open cross-sections. Occurrence of bending in the truss’ chord is the result of specific production technology assumed by the designer and producer of lattice girder’s systems. The aim of this research is to present methodology of conduct while creating numerical models that best depict the behaviour...
-
Efficiency of the Use of LTE System Radio Resources in Highway Transport Enironment
PublicationThe paper describes the problem of analysis of throughput-coverage characteristics of the LTE system. Simulation results of the efficiency of the use of LTE radio resources are presented. Simulation studies on the basis of original model of the LTE network simulator were carried out. In addition, the evaluation of throughput for a single connection, and available capacity were evaluated in the context of the use of the same...
-
Methods of Network Resource Provisioning for the Future Internet IIP Initiative
PublicationIn this paper, we present specification, design and implementation aspects of a network resource provisioning module introduced for the Polish Initiative of Future Internet called System IIP. In particular, we propose a set of novel LP optimization models of network resource provisioning designed to minimize the network resource consumption, either bandwidth or node’s computational power, as well as to maximize the residual capacity....
-
Modeling of truss with cold-formed section and positive eccentricity in the node
PublicationThis work is dedicated to establishing the load carrying capacity of tensed and compressed truss’ nodes made of cold-formed open cross sections. The occurrence of bending in the truss’ nodes is the result of a specific production technology for system lattice girders assumed by the designer and the producer. The aim of this research is to present the methodology of conduct for creation of computational models that best depict the...
-
Superconductivity in the niobium-rich compound Nb5Se4
PublicationThe niobium rich selenide compound Nb5Se4 was synthesized at ambient pressure by high-temperature solid–state reaction in a sealed Ta tube. Resistivity and heat capacity measurements reveal that this compound is superconducting, with a Tc = 1.85K. The electronic contribution to the specific heat γ and the Debye temperature are found to be 18.1 mJmol−1K−2 and 298 K respectively. The calculated electron-phonon coupling constant λep...
-
Large thermo-elastic displacement and stability FEM analysis of multilayered plates and shells
PublicationThe paper concerns the load capacity analysis of thermally loaded multilayered plates and shells. The multilayered body is treated as an equivalent single layer whose kinematics is consistent with first order shear deformation theory. The authors focus on the thermo-elastic stability problem of the thin-walled structures. The equilibrium paths are traced with the use of Riks-Wempner-Ramm algorithm. By making use of the Tsai-Wu...
-
Wireless Charging Station Design for Electric Scooters: Case Study Analysis
PublicationThis study proposes an example of a wireless charging station design for a small-scale vehicle available on the market. The article analyzes basic transmitter inverter topologies and their compensation methods in terms of flexibility of control, tolerance to uncertainty in positioning, and the possibility of decreasing the integration price. Our comprehensive analysis focuses on the battery voltage range, energy capacity, cost,...
-
Normal stress distribution in built‑up cold‑formed column in relation to interconnecting bolt spacing
PublicationIn order to increase a stiffness of cold-formed steel (CFS) elements it is practised to built-up the cross-section. In the analysed case, a main element is strengthened by adding extra chord in contact partially along the column. This additional chord acts as a longitudinal stiffener connected with the main section by series of bolts. Authors check whether rules applied over the years, for hot-rolled elements, can be indiscriminately...
-
Shaft friction from the DMT and direct shear interface tests
PublicationThe article presents preliminary attempt to create tri-linear transfer curves for describing pile behaviour under axial loading. Transfer curves would use the parameter measured in dilatometer test, particularly a constrained modulus MDMT. The proposed method is based on concrete rough and smooth interface tests performed in a direct shear apparatus. Based on the obtained mobilization curves, relationships were created between...
-
Modeling and experimental investigation of the small UPQC systems
PublicationIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model were talked over. In short form power balance as well as fundamental dependences and analytic model with regard of decoupling circuits were investigated. Applied method for DC link capacity selection...
-
The effect of laser on metal surfaces for multidisciplinary usage in material and thermal engineering
PublicationThe subject of heat transfer and cooling systems is still a matter of contention in many different fields of science and industry. Infrigidation is much more difficult than warming, and so, much more needed in more and more different devices, starting from massive industrial machinery and air conditioning in commercial buildings, up to micro and nano-surgery tools. In fact, the size of many cooling systems is still a problem. It...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublicationIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Experimental study of the post tensioned prestressed concrete corbels
PublicationThe results of experimental investigation of 6 symmetrical double prestressed corbels of variable shear span to depth ratio and variable location of prestressing bars are presented in the paper. The post ten- sioned corbels were prestressed with Macalloy 1030 bars of 25 mm in diameter. The results of the tests were compared with the cracking and load carrying capacity of corbels reinforced with passive reinforce- ment. As a result...
-
Higher harmonics produced by traction substations – computer modelling and experimental verification
PublicationVoltage and current harmonics have a detrimental effect on the components of a power system. Current harmonics may result in the overload and damage to power transformers, although the rms value of load current does not exceed their current-carrying capacity. Voltage harmonics may result in, for example, damage to capacitor banks used to compensate reactive power. Devices which contribute to both current and voltage distortion...
-
Research on Quality Requirements of Data Transmission Services in RSMAD
PublicationThe paper presents a results and analysis of research of the quality of service requirements (defined by the QoS attributes) for imaging data transmission services using Radio System for Monitoring and Acquisition of Data from Traffic Enforcement Cameras (in short RSMAD). The paper also presents and discusses results of test on the impact of the size of photos from traffic enforcement cameras on the average transmission time. These...
-
Geokompozyty drenażowe w odwodnieniach drogowych i kolejowych
PublicationZagadnienie zagospodarowania wód opadowych i gruntowych w rejonie konstrukcji drogowych i kolejowych stanowi istotny element bezpiecznej i efektywnej eksploatacji tych obiektów. Odpowiednie wykorzystanie geokompozytów drenażowych zapewnia bezproblemową pracę konstrukcji oraz właściwą ochronę przed uszkodzeniami wynikającymi z niekontrolowanego oddziaływania wody.
-
Modernizacja układów geometrycznych toru z wykorzystaniem metody oceny wielokryterialnej
PublicationW pracy przedstawiono główne założenia opracowanej metody wielokryterialnej oceny stosowanej przy przebudowie układów geometrycznych toru. Określono kryteria wpływające na inwestycje modernizacyjne. Zdefiniowano zastosowaną w analizie funkcję celu. Przedstawiono przykład zastosowania algorytmu optymalizacyjnego z wykorzystaniem programu komputerowego
-
Modelowanie losowych imperfekcji geometrycznych przestrzennych konstrukcji metalowych
PublicationImperfekcje geometryczne zbiorników, silosów i powłok siatkowych mogą znaczą-co wpłynąć na ich nośność, a więc powinny być one uwzględniane w obliczeniach komputerowych i w procesie projektowania. Wykazano, że przy podstawowych obcią-żeniach, działających na tego typu konstrukcje, tj. podciśnieniu oraz naporu wiatru i śniegu (w przypadku powłok siatkowych), wykazują wyraźne różnice w porównaniu z analogicznymi wynikami dla tych...
-
Modyfikacja połączenia dźwigara ze słupem w konstrukcji stalowej Terminalu T2 Portu Lotniczego w Gdańsku
PublicationW2015 r. ukończono rozbudowę Terminalu T2 Portu Lotniczego im. Lecha Wałęsy wGdańsku. Politechnika Gdańska pełniła nadzór naukowy nad rozbudową obiektu. Wykonano wiele analiz, których celem była weryfikacja pracy konstrukcji w fazach montażu oraz w stanie docelowym. Wnioski z przeprowadzonych badań doprowadziły do modyfikacji oparcia dźwigarów dachowych na stalowych słupach nośnych, z uwagi na stwierdzone lokalne przekroczenia...
-
Managerial Energy in Sustainable Enterprises: Organizational Wisdom Approach
PublicationThe circular economy (CE) as an idea involves applying the concept of sustainable development that has been gaining worldwide support. This shift in perception of energy and resource-use from its linear to circular forms creates a specific business environment, which constitutes the subject of this research. This article aims to analyze the impact of a manager’s energy on organizational wisdom, focusing on its circular business...
-
Development, characterization and evaluation of composite adsorbent for the adsorption of crystal violet from aqueous solution: Isotherm, kinetics, and thermodynamic studies
PublicationThe purpose of this work focuses on the production and investigations of a new composite material as alternative low-cost adsorbent for the removal of crystal violet (CV) dye from waste solution. The production method was performed by in-situ thermal activation technology via extrusion process of polymer wastes containing tire rubber (50 wt%) and polyurethane foam (50 wt%) using single-screw extruder under processing temperature...
-
Characterization of diatomaceous earth coated with nitrated asphaltenes as superior adsorbent for removal of VOCs from gas phase in fixed bed column
PublicationAsphaltenes isolated from bitumen possess unusual adsorption characteristics that can be further enhanced by chemical modifications to promote interactions with VOCs’. Herein, nitrated asphaltenes are used as an active layer coated on a surface of a diatomaceous earth, in order to prepare an efficient adsorbent (AsfNitro). Breakthrough experiments with benzene, pyridine, and 1-nitropropane revealed significant increase in adsorption...
-
Fermi-liquid behavior of binary intermetallic compounds Y3 M (M = Co, Ni, Rh, Pd, Ir, Pt)
PublicationA series of polycrystalline samples of Y3 M (M = Co, Ni, Rh, Pd, Ir, Pt), intermetallic binary compounds were synthesized by the arc-melting method. Powder x-ray diffraction (pXRD) confirmed the orthorhombic cementite-type crystal structure and allowed for the estimation of the lattice parameters. Physical properties were investigated by means of electrical resistivity and heat capacity measurements between 1.9 K and 300 K. All...
-
Błędy cyfrowej rejestracji prędkości obrotowej z wykorzystaniem przetwornika obrotowo-impulsowego
PublicationPrzedstawiono zasadę działania przetwornika obrotowo-impulsowego w zastosowaniu do pomiaru prędkości obrotowej. Omówiono metody rejestracji on-line sygnału impulsowego z przetwornika obrotowo-impulsowego. W metodach tych prędkość obrotowa wyznaczana jest na podstawie ostatniego przedziału miedzyimpulsowego lub na podstawie dwóch ostatnich przedziałów miedzyimpulsowych z ekstrapolacji. Dla sinusoidalnej zmiany prędkości udowodniono,...
-
Dynamic Positioning System with Vectorial Backstepping Controller
PublicationThe problem of synthesis a dynamic positioning system for low frequency model of surface vessel was considered in this paper. The recursive vectorial backstepping control design was used to keep a fixed position and heading in presence of wave disturbances. The passive observer was introduced to smooth the measurements and to estimate the velocities needed for the control algorithm. Some parameters of observer were optimized off-line...
-
Synthesis and biological activity of mycophenolic acid-amino acid derivatives
PublicationIn search of new immunosuppressants, mycophenolic acid (MPA) was coupled with amino acid methyl esters followed by hydrolysis to analogs bearing free carboxylic groups. The obtained compunds were tested in vitro as growth inhibitors of lymphoid cell line (Jurkat) and human peripheral blood mononuclear cells (PBMC) from healthy donors. According to obtained results recovering of free carboxylic group increased their activity. Additionally,...
-
Test Execution Logging and Visualization Techniques
PublicationTraditionally, log traces of test cases ex ecution are stored in textual format and their analysis is done in a post- execution phase. Our approach bases on the concept of gr aphical presentation of te st execution which enables better analysis of log traces and also gives the opportunity to consider them on-line. In particular, we discuss the graphical symbols we chose, we pres ent the logging interface we defined a nd describe...
-
Elliptical slot UWB monopole antenna
PublicationThe UWB monopole antenna with elliptical radiating slot end and microstrip feeding line terminated with radial stub have been designed, fabricated and measured. The antenna show return loss less than -12 dB in the whole UWB bandwidth. Linearity of the reflection coefficient phase product have also been achieved. Radiation patterns of the antenna measured at three selected frequency points indicated regular, approximately omni directional...
-
On the instantaneous frequency smoothing for signals with quasi-linear frequency changes
PublicationThe problem of estimation of the slowly-varying instantaneous frequency of a nonstationary complex sinusoidal signal buried in noise is considered. This problem is usually solved using frequency tracking algorithms. It is shown that the accuracy of frequency estimates can be considerably increased if the results yielded by the frequency tracker are further processed using the appropriately designed filters. The resulting frequency...
-
Budowanie zaufania w relacjach interentowych
PublicationArtykuł prezentuje znaczenie zaufania w relacjach interpersonalnych oraz wpływ globalizacji na proces budowania i percepcji zaufania pomiędzy uczestnikami relacji społecznych. Przedstawiono badania własne, w których autorka zweryfikowała postawy badanych wobec zaufania w relacjach internetowych i poziom wiarygodności partnera w komunikacji odbywającej się z wykorzystaniem różnych internetowych funkcjonalności (forum internetowe,...
-
Economic benefits of dynamic charging of electric buses
PublicationDiesel engines buses are still the most used type of buses. Electric buses provide promising green alternatives and a lot of advantages, but their main disadvantages are limited travel range and long charging time. This article is a presentation of innovative solution for charging of electric busses - Dynamic Charging (IMC). The modern IMC system in Solingen was presented. At the end of the article, a proposal was made to introduce...
-
Techniki śródoperacyjnego monitorowania EKG
PublicationZ badania EKG lekarze uzyskują szereg cennych informacji niezbędnych do prawidłowego podejmowanie ważnych decyzji terapeutycznych. EKG stało się pierwszym parametrem monitorowanym standardowo i w sposób ciągły podczas znieczulenia. Współczesna technika umożliwia nie tylko ciągłe monitorowanie zapisu EKG, a także transmisję danych on-line do dowolnego miejsca w szpitalu, i ich cyfrową rejestrację. Najistotniejszym kryterium przydatności...
-
A Point Set Connection Problem for Autonomous Mobile Robots in a Grid
PublicationConsider an orthogonal grid of streets and avenues in a Manhattan-like city populated by stationary sensor modules at some intersections and mobile robots that can serve as relays of information that the modules exchange, where both module-module and module-robot communication is limited to a straight line of sight within the grid. The robots are oblivious and move asynchronously. We present a distributed algorithm that, given...
-
Reference FEM model for SHM system of cable-stayed bridge in Rzeszów
PublicationThe paper presents the references model for structural health monitoring system (SHM) of cable-stayed bridge recently constructed in Rzeszów over Wisłok River. The SHM system is design to provide on-line information on the structure state and facilitate its maintenance procedures. The main feature of the SHM system is permanent observation of the dynamic behavior of the bridge with focus on cable vibrations. The paper discusses...
-
Regulation of Cellular Redox Homeostasis by (–)-Epicatechin and Cocoa Extracts—A Pilot Study
PublicationCocoa polyphenols play an important role in protection against diseases in which oxidative stress is implicated as a causal or contributing factor. The main aim of this study was to elucidate the influence of different cocoa extracts and main cocoa bioactive compound (–)-epicatechin on cell growth and support of antioxidant cellular barrier in colon adenocarcinoma cell line model (HT29). Results show that the tested cocoa bioactivity...
-
REGULATION OF CELLULAR REDOX HOMEOSTASIS BY (-)-EPICATECHIN AND COCOA EXTRACTS – PILOT STUDY
PublicationCocoa polyphenols play an important role in protection against diseases in which oxidative stress is implicated as a causal or contributing factor. The main aim of this study was to elucidate the influence of different cocoa extracts and main cocoa bioactive compound (–)-epicatechin on cell growth and support of antioxidant cellular barrier in colon adenocarcinoma cell line model (HT29). Results show that the tested cocoa bioactivity...
-
An Approach to Mean Path Loss Model Estimation for Off-Body Channels
PublicationThis paper presents an approach to estimation of the mean path loss model parameters in off-body Body Area Networks channels. In this approach, the path loss exponent is constrained to a value obtained for the line-of-sight (LoS) propagation in the co-polarised channel, considering a generalised static scenario. The comparison of the goodness of fit between the proposed approach and other approaches, for a set of measurements obtained...
-
A Noether theorem for stochastic operators on Schatten classes
PublicationWe prove that a stochastic (Markov) operator S acting on a Schatten class C_1 satisfies the Noether condition S'(A) = A and S'(A^2) = A^2, where A is a Hermitian bounded linear operator on a complex Hilbert space H, if and only if, S(E(G)XE(G)) = E(G)S(X)E(G) holds true for every Borel subset G of the real line R, where E(G) denotes the orthogonal projection coming from the spectral resolution of A. Similar results are obtained...
-
Modelowanie zmiennej krzywizny na długości toru zwrotnego rozjazdu
PublicationW pracy została przedstawiona analityczna metoda wyznaczania krzywizny toru zwrotnego rozjazdu kolejowego posiadającego na swojej długości odcinki zmiennej krzywizny. Taki rozjazd jest dedykowany w głównym stopniu kolejom dużych prędkości. Rozpatrzono dwa odrębne przypadki obejmujące liniowy przebieg krzywizny oraz przebieg nieliniowy, w postaci wielomianowej. Uzyskane rozwiązania problemu pozwalają na przyjmowanie dowolnych wartości...
-
Cyfrowa wewnątrzsamolotowa magistrala komunikacyjna ARINC 429
PublicationW artykule przedstawiono standard cyfrowej magistrali komunikacyjnej ARINC 429 przeznaczonej do współpracy urządzeń na pokładzie samolotów. Skupiono się na warstwie fizycznej i protokolarnej tego standardu.