displaying 1000 best results Help
Search results for: SHEAR YIELD STRENGTH
-
High-performance method of carbon nanotubes modification by microwave plasma for thin composite films preparation
PublicationIn this work we present a simple and efficient method of nitrogen plasma modification of carbon nanotubes (CNTs). The process allows for treatment of the nanotubes in the form of powder with quite a high yield (65 mg of CNTs per hour). The modified carbon nanotubes contain approx. 3.8% of nitrogen, mostly in the pyridinic form. Plasma treated CNTs exhibit better dispersibility in water and higher electric capacitance than pristine...
-
Superconductivity and ferromagnetism in Pd doped Y9Co7
PublicationThe ferromagnetic superconductor Y9Co7 was chemically doped to yield the solid solution Y9Co7-xPdx for 0 < x < 0.4. The lattice parameter a does not depend on x, whereas c increases with increasing Pd content up to x ¼ 0.2, the palladium solubility limit. The transition from ferromagnetism (TC ¼ 4.25 K) to superconductivity (Tsc ¼ 2.4 K) was observed only for the parent Y9Co7 compound. For the lowest tested Pd doping level (x ¼...
-
On the correlation between magnetoacoustic emission and magnetostriction dependence on the applied magnetic field
PublicationThe correlation between magnetoacoustic emission signal envelopes and magnetostriction curves is investigated. Two sets of samples are being considered: tempered martensitic steel and plastically deformed ferritic steel. It is shown that even though some general relations may be observed, as was demonstrated in the literature, the correlation is not always present. One may not expect to change both quantities in the same way if...
-
Non-adiabatic Effects in Pressure Drop Calculations in Flow Boiling and Flow Condensation in Minichannels
PublicationConsiderations presented in the paper relate both to the case of flow boiling and flow condensation in conventional channels as well as small diameter ones. Authors devoted all the possible attention that the modeling presented is applicable to the whole range of quality variation in both cases of condensation and boiling. The form of two-phase flow multiplier, which is a major factor in modeling presented here, should be capable...
-
Soil-structure interaction effects on modal parameters of office buildings with different number of stories
PublicationThe paper summarizes the results of a numerical investigation designed to study the soil-structure interaction effects on modal parameters of three office buildings. The reinforced-concrete 4-storey, 8-storey, and 12-storey office buildings, each with additional two levels of embedded basements, represent low, medium, and high-rise structures, respectively. In order to conduct this research, detailed finite-element structure models...
-
On the Buckling Response of Axially Pressurized Nanotubes Based on a Novel Nonlocal Beam Theory
PublicationIn the present study, the buckling analysis of single-walled carbon nanotubes (SWCNT) on the basis of a new refined beam theory is analyzed. The SWCNT is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new proposed beam theory has only one unknown variable which leads to one equation similar to Euler beam theory and is also free from any shear correction factors. The equilibrium...
-
Activated Tungsten Inert Gas Weld Characteristics of P91 Joint for Advanced Ultra Supercritical Power Plant Applications
PublicationActivated Tungsten Inert Gas (A-TIG) welding, a variant of tungsten inert gas (TIG) welding, was used for welding P91. In Generation IV power plants, P91 welds are prone to premature failure due to the presence and formation of brittle phases and creep at high temperatures. When performing A-TIG welding, the flux composition plays a role in the reversal of the Marangoni flow in the weld pool, which ultimately determines the level...
-
Mechanical Properties of Polyester Coated Fabric Subjected to Biaxial Loading
PublicationThe paper is focused on the comparison between uniaxial and biaxial laboratory test results for polyester coated fabric. A short literature review concerning coated woven fabrics with emphasis on biaxial tensile tests is presented. A description of the polyester-coated fabric under biaxial test by means of constitutive models and material parameter values is proposed. To establish the right values of the ultimate tensile strength,...
-
Fabrication of Composite Polyurethane/Hydroxyapatite Scaffolds Using Solvent-Casting Salt Leaching Technique
PublicationScaffolds are porous three-dimensional structures which are used to fill bone losses and make them possible to cells to grow. Many different structural and biological properties are required from them: porosity, mechanical strength and biocompability. The present research is aimed at development of composite polyurethane/hydroxyapatite scaffolds by using the solvent-casting salt leaching method. The SEM examinations were applied...
-
Analysis of pounding between adjacent buildings founded on different soil types
PublicationEarthquake-induced pounding was experienced in many previous earthquakes and it was found to be a critical issue. This study investigates the effect of pounding between buildings founded on the same and different soil types. Three 3-D buildings with 4, 6 and 8 storeys were considered in this study. Three pounding scenarios were taken into account, i.e. pounding between 4-storey and 6-storey buildings, between 4-storey and 8-storey...
-
Importance of sign conventions on analytical solutions to the wave-induced cyclic response of a poro-elastic seabed
PublicationThis paper discusses the influence of different sign conventions for strains and stresses, i.e. the solid mechanics sign convention and the soil mechanics sign convention, on the form of governing partial differential equations (the static equilibrium equations and the continuity equation) used to describe the wave-induced cyclic response of a poro-elastic seabed due to propagation of a sinusoidal surface water-wave. Some selected...
-
Stabilization of N-, N,N-, N,N'-Methylated and Unsubstituted Simple Amidine Salts by Multifurcated Hydrogen Bonds
PublicationIn the light of the usefulness of amidines in medicinal chem., this paper considers the effects on biol. properties and chem. reactivities of org. mols. affected by intramol. interactions. The study of chem. shifts has been an important source of information on the electronic structure of amidine salts and their ability to form non-covalent bonds with nucleic acids. The NMR and IR results demonstrate that hydrogen bonds are...
-
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublicationThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
A simplified method to assess the impact of ship-to-ship collision on the risk of tanker ship hull girder breaking accounting for the effect of ageing
PublicationOne of the most critical structural failures is the exceedance of the ship hull girder’s ultimate strength, which may result in hull breaking, and subsequent severe consequences, including loss of life and property as well as environmental damage in case of an oil spill. A cause for such loss of structural continuity can be triggered by a collision with another vessel. In addition, the ageing mechanisms of the hull structure could...
-
Evaluating Gelatin-Based Films with Graphene Nanoparticles for Wound Healing Applications
PublicationIn this study, gelatin-based films containing graphene nanoparticles were obtained. Nanoparticles were taken from four chosen commercial graphene nanoplatelets with different surface areas, such as 150 m2/g, 300 m2/g, 500 m2/g, and 750 m2/g, obtained in different conditions. Their morphology was observed using SEM with STEM mode; porosity, Raman spectra and elemental analysis were checked; and biological properties, such as hemolysis...
-
Analytical chemistry in technical approaches: immobilization of biosorbent waste containing heavy metals in cemented materials
PublicationAn ecologically safe and economically justified method of stabilization of the used biosorbents was developed. Sorbent contaminated with heavy metals has been successfully solidified/stabilized using a hydraulic binder. The test results indicated that up to 1% of the biosorbent residue used could be added without compromising the compressive strength of the mortar. The compressive strength of the modified mortars did not change...
-
The Effect of Fly Ash Microspheres on the Pore Structure of Concrete
PublicationThe fly ash microspheres (FAMs) formed during the mineral transformation stage in coal combustion are hollow spherical particles with a density less than water. This paper presents the results of X‐ray micro‐computed tomography and an automatic image analysis system of the porosity in the structure of hardened concrete with microspheres. Concrete mixtures with ordinary Portland cement and two substitution rates of cement by microspheres—5%...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublicationLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
NUMERICAL MODEL OF PLASTIC DESTRUCTION OF THICK STEEL STRUCTURAL ELEMENTS
PublicationIn the shipbuilding industry, the risk of brittle fracture of the structure is limited by using certified materials with specified impact strength, determined by the Charpy method (for a given design temperature) and by supervising the welding processes (technology qualification, production supervision, non-destructive testing). For off-shore constructions, classical shipbuilding requirements may not be sufficient. Therefore, the...
-
THE EFFECT OF NOTCH DEPTH ON CTOD VALUES IN FRACTURE TESTS OF STRUCTURAL STEEL ELEMENTS
PublicationIn elements of steel structures working at low temperatures, there is a risk of appearance of brittle fracture. This risk is reduced through the use of certified materials having guaranteed strength at a given temperature. A method which is most frequently used to determine brittle fracture toughness is the Charpy impact test, preformed for a given temperature. For offshore structures intended to work in the arctic climat e, the...
-
Muneer Ahmed Mr
PeopleLooking for an organization where I can better utilize my scientific and technical skills in the arena of research or work as a faculty person. Besides, I am also willing to work as professional engineer with dedication and diligence in dynamic environment. Likewise, I've been a committed and tenacious candidate throughout my career. I am aware of the level of commitment, dedication and strength required. Despite the fact that...
-
Design space reduction and variable-fidelity EM simulations for feasible Pareto optimization of antennas
PublicationA computationally efficient procedure for multi-objective optimization of antenna structures is presented. In our approach, a response surface approximation (RSA) model created from sampled coarse-discretization EM antenna simulations is utilized to yield an initial set of Pareto-optimal designs using a multi-objective evolutionary algorithm. The final Pareto front representation for the high-fidelity model is obtained using surrogate-based...
-
Excitation energy transfer in partly ordered polymer films differing in donor and acceptor transition moments orientation
PublicationBased on spectroscopic measurements selected properties of nonradiative Förster energy transport are studied in uniaxially stretched polyvinyl alcohol thin films for three systems differing in donor and acceptor transition moments orientation relative to the axis of stretching. In particular, donor – acceptor emission anisotropy spectra yield completely different regularities for these systems in uniaxially stretched films, whereas...
-
Velocity Field Characteristics at the Inlet to a Pipe Culvert
PublicationA poorly designed culvert inlet structure causes scouring, which can lead to the collapse of the culvert and significant damage to the neighboring land. A set of laboratory tests was evaluated to examine velocity distribution at the culvert inlet. A three-dimensional acoustic Doppler velocimeterwas used to measure instantaneous flowvelocity upstream of the culvert. The analysis of mean velocities, turbulence strength, and Reynolds...
-
Materiały stosowane do wytwarzania implantów kości
PublicationMateriały stosowane do wytwarzania implantów kostnych muszą być biokompatybilne, nietoksyczne, bioaktywne oraz wykazywać odpowiednie właściwości mechaniczne, takie jak wytrzymałość na ściskanie, na zginanie oraz sztywność i twardość. Gama stosowanych materiałów jest bardzo szeroka, obejmuje metale, polimery, ceramikę oraz ich kompozyty. Każdy z tych materiałów ma swoje mocne i słabe strony. Praca stanowi przegląd materiałów stosowanych...
-
Symulacje przepływu ciepła przez płytę betonową
PublicationW pracy przedstawiono symulacje numeryczne dojrzewania betonu w płycie górnej skrzynki czteroprzęsłowego mostu typu extradosed. Model matematyczny opisujący przepływ ciepła dedykowany jest do prognozowania dojrzałości i wytrzymałości twardniejącego betonu. Proponowany model zaimplementowano w autorskim programie numerycznym napisanym w środowisku Matlab. Podejście numeryczne zweryfikowano za pomocą danych doświadczalnych uzyskanych...
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated panels
PublicationComposite structural insulated panels (CSIPs) are novel prefabricated elements for structural applications. Panels under consideration are made from glass-fibre reinforced magnesia cement boards as facesheets and expanded polystyrene foam (EPS) as a core. Quasi-static full-scale and model bending tests under monotonic loading were performed to recognize mechanical properties of CSIPs in flexure. In addition, tensile, compressive,...
-
COMPARISON OF INFINITE ELEMENT MODELS
PublicationThe main objective of this paper is to show the comparison of two models of infinite ab- sorbing layer with increasing damping in numerical investigations of elastic wave prop- agation in unbounded structures. This has been achieved by the Authors by a careful in- vestigation of two different engineering structures characterised by gradually increasing geometrical and mathematical description complexities. The analysis included...
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublicationThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
-
Torsional stability capacity of a nano-composite shell based on a nonlocal strain gradient shell model under a three-dimensional magnetic field
PublicationThis paper considers a single-walled composite nano-shell (SWCNS) exposed in a torsional critical stability situation. As the magnetic field affects remarkably nanostructures in the small size, a three-dimensional magnetic field is assessed which contains magnetic effects along the circumferential, radial and axial coordinates system. Based on the results of the nonlocal model of strain gradient small-scale approach and the first-order...
-
Buckling Analysis of a Micro Composite Plate with Nano Coating Based on the Modified Couple Stress Theory
PublicationThe present study investigates the buckling of a thick sandwich plate under the biaxial non-uniform compression using the modified couple stress theory with various boundary conditions. For this purpose, the top and bottom faces are orthotropic graphene sheets and for the central core the isotropic soft materials are investigated. The simplified first order shear deformation theory (S-FSDT) is employed and the governing differential...
-
Electromagnetic forced vibrations of composite nanoplates using nonlocal strain gradient theory
PublicationThis article is intended to analyze forced vibrations of a piezoelectric-piezomagnetic ceramic nanoplate by a new refined shear deformation plate theory in conjunction with higher-order nonlocal strain gradient theory. As both stress nonlocality and strain gradient size-dependent effects are taken into account using the higher-order nonlocal strain gradient theory, the governing equations of the composite nanoplate are formulated....
-
Optimization-Based Robustness Enhancement of Compact Microwave Component Designs with Response Feature Regression Surrogates
PublicationThe ability to evaluate the effects of fabrication tolerances and other types of uncertainties is a critical part of microwave design process. Improving the immunity of the device to parameter deviations is equally important, especially when the performance specifications are stringent and can barely be met even assuming a perfect manufacturing process. In the case of modern miniaturized microwave components of complex topologies,...
-
Rapid Design Centering of Multi-Band Antennas Using Knowledge-Based Inverse Models and Response Features
PublicationAccounting for manufacturing tolerances as well as uncertainties concerning operating conditions and material parameters is one of the important yet often neglected aspects of antenna development. Appropriate quantification of uncertainties allows for estimating the fabrication yield but also to carry out robust design (e.g., yield maximization). For reliability reasons, statistical analysis should be executed at the accuracy level...
-
Rigid polyurethane foams with different flame retardants and their physical and mechanical properties
PublicationRigid polyurethane foams (PUFs) containing 3, 6 or 9 % of one of of two selected fire retardants (FR): oligomeric ethyl ethylene phosphate (Fyrol PNX) and expandable graphite (EG) were prepared, inspected and compared to foam without that fillers as the control. The thermal stability of PUFs was described by horizontal test according to norm: UL 94 HB. Compressive strength and physical properties (density, fragility and water absorption)...
-
Rozkład naprężeń mechanicznych w łyżce o szerokości 500 mm, przeznaczonej do koparki podsiębiernej
PublicationW artykule zaprezentowano optymalizację kształtu łyżki koparki przedsiębiernej z wykorzystaniem analizy wytrzymałościowej. Analizę oparto na trójwymiarowym modelu konstrukcji łyżki z zastosowaniem metody elementów skończonych (MES). Opracowanie wspomnianej metody pozwoliło na modyfikację konstrukcji łyżki, która dała w efekcie obniżenie naprężeń złożonych w newralgicznych obszarach konstrukcji łyżki. Przedstawiona analiza okazała...
-
Identyfikacja gatunku stali zastosowanej w obiektach budowlanych
PublicationEksploatacja istniejących metalowych konstrukcji budowlanych często związana jest z zagadnieniem koniecznej szczegółowej identyfikacji rodzaju materiału stalowego pod kątem je go cech wytrzymałościowych i składu chemicznego. Dostępne standardowe metody laboratoryjne zazwyczaj wymagają pobrania z konstrukcji próbek materiału do badań, co nie zawsze jest możliwe. W artykule zaprezentowano alternatywne metody oceny wymienionych cech...
-
XPS data of deuterium and hydrogen grown boron-doped diamond
Open Research DataThe high-resolution C1s X-ray absorption spectra of BDD@H and BDD@D samples were measured using the facilities of the HE-SGM beamline (HE-SGM) at the BESSY II synchrotron radiation source of Helmholtz–Zentrum Berlin (HZB).[90] The measurements were carried out under ultra-high vacuum conditions: P ≈ 2×10−9 Torr at T = 300 K. The NEXAFS spectra were...
-
Stochastic intervals for the family of quadratic maps
Open Research DataNumerical analysis of chaotic dynamics is a challenging task. The one-parameter families of logistic maps and closely related quadratic maps f_a(x)=a-x^2 are well-known examples of such dynamical systems. Determining parameter values that yield stochastic-like dynamics is especially difficult, because although this set has positive Lebesgue measure,...
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Thermomechanical and Fire Properties of Polyethylene-Composite-Filled Ammonium Polyphosphate and Inorganic Fillers: An Evaluation of Their Modification Efficiency
PublicationThe development of new polymer compositions characterized by a reduced environmental impact while lowering the price for applications in large-scale production requires the search for solutions based on the reduction in the polymer content in composites’ structure, as well as the use of fillers from sustainable sources. The study aimed to comprehensively evaluate introducing low-cost inorganic fillers, such as copper slag (CS),...
-
The Influence of Cement Type on Early Properties of Cold In-Place Recycled Mixtures
PublicationCold in-place recycling is a commonly used maintenance treatment in rehabilitation of low and medium volume roads in Poland. Typically, two types of binding agents are used—cement and bituminous emulsion (or foamed bitumen).Due to the harsh Polish climate with many freeze/thaw cycles and frequent occurrence of saturated conditions, the used amounts of cement are higher than those commonly used in warmer parts of Europe. While there...
-
Modele numeryczne uwzględniające tarczową pracę pokrycia dachowego z blach trapezowych
PublicationW artykule porównano wybrane sposoby uwzględniania w modelowaniu numerycznym tarczowej pracy pokrycia dachowego z blachy trapezowej, możliwe do zrealizowania w programie Autodesk Robot Structural Analysis Professional 2015, w celu oceny słuszności stosowania ich do obliczeń konstrukcji nośnej współpracującej z poszyciem z blachy trapezowej. Analizy przeprowadzono dla pojedynczej przepony. Za pomocą powłokowych elementów skończonych...
-
New approaches for improving selectivity and sensitivity of resistive gas sensors: A review
PublicationResistive gas sensors are very popular and reliable but suffer from low selectivity and sensitivity. Various methods have been suggested to improve both features without increasing the number of sensors in gas detection systems. Fluctuation enhanced gas sensing was proposed to improve gas detection efficiency by analyzing low-frequency resistance fluctuations, and noise parameters can be more informative than the single DC resistance...
-
A study of concentration depolarization and quenching of photoluminescence of solutions
PublicationThe concentration-dependence of emission anisotropy r/r0 and quantum yield eta/eta0 of the photoluminescence of glycerol-water solutions of rhodamine B in two systems of viscosities 7.4 P and 0.72 P is investigated. The experimental data are compared with the new theory of concentraticn depolarization (J. Lumin., 5, 413 (1972)) and concentration quenching of photoluminescence (Acta Phys. Hungar., 30, 145 (1972)), which takes...
-
Aerodynamic shape optimization by variable-fidelity computational fluid dynamics models: a review of recent progress
PublicationA brief review of some recent variable-fidelity aerodynamic shape optimization methods is presented.We discuss three techniques that—by exploiting information embedded in low-fidelity computationalfluid dynamics (CFD) models—are able to yield a satisfactory design at a low computational cost, usu-ally corresponding to a few evaluations of the original, high-fidelity CFD model to be optimized. Thespecific techniques considered here...
-
Fast Multi-Objective Optimization of Narrow-Band Antennas Using RSA Models and Design Space Reduction
PublicationComputationally efficient technique for multi-objective design optimization of narrow-band antennas is presented. In our approach, the corrected low-fidelity antenna model (obtained through coarse-discretization EM simulations) is enhanced using frequency scaling and response correction, sampled, and utilized to obtain a fast response surface approximation (RSA) antenna surrogate. The RSA model is constructed in the reduced design space....
-
Pyrolysis Combined with the Dry Reforming of Waste Plastics as a Potential Method for Resource Recovery—A Review of Process Parameters and Catalysts
Publication: Emissions of greenhouse gases and growing amounts of waste plastic are serious environmental threats that need urgent attention. The current methods dedicated to waste plastic recycling are still insufficient and it is necessary to search for new technologies for waste plastic management. The pyrolysis-catalytic dry reforming (PCDR) of waste plastic is a promising pro-environmental way employed for the reduction of both CO2 and...
-
Decrease in Photovoltaic Module Efficiency Due to Deposition of Pollutants
PublicationThe deposition of pollutants on the surface of photovoltaic (PV) modules reduce the efficiency that can be achieved in given climatic conditions. This results in the loss of energy yield obtained from the solar installation. A number of factors determine the scale of this problem. The first of these is the amount of impurities deposited, the associated amount of precipitation, and the speed and direction of the wind. A second aspect...
-
Chromogenic azomacrocycles with imidazole residue: Structure vs. properties
PublicationNew diazo macrocycles linked by hydrocarbon chain bearing imidazole or 4-methylimidazole residue have been synthetized with satisfactory yield (24–55%). The structure of macrocycles was confirmed by X-ray analysis and spectroscopic methods (1H NMR, MS, FTIR). Metal cation complexation studies were carried out in acetonitrile and acetonitrile-water system. It was found that azomacrocyles form triple-decker complexes with lead(II)....