Search results for: knowledge base
-
Analytical Steady-State Model of the Pipeline Flow Process
PublicationThe paper addresses the issue of modeling the flow process in transmission pipelines. A base model used for numerical simulation is introduced. Under certain assumptions concerning steady state analysis, the differential equations describing the process are solved analytically for two cases: zero and nonzero inclination angle α. These equations describe a constant flow rate and a corresponding distribution of the pressure along...
-
CFD and FEM model of an underwater vehicle propeller
PublicationDuring the project execution of design and optimization the Remotely Operated Vehicle (ROV) research on its propulsion has been carried out. The entire project was supported by CFD and FEM calculations, which taking into account the characteristics of underwater vehicle. One of the tasks was to optimize the semi-open duct for horizontal propellers, which provided propulsion and controllability in horizontal plane. In order to...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublicationTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Antibacterial Activity and Cytocompatibility of Bone Cement Enriched with Antibiotic, Nanosilver, and Nanocopper for Bone Regeneration
PublicationBacterial infections due to bone replacement surgeries require modifications of bone cement with antibacterial components. This study aimed to investigate whether the incorporation of gentamicin or nanometals into bone cement may reduce and to what extent bacterial growth without the loss of overall cytocompatibility and adverse effects in vitro. The bone cement Cemex was used as the base material, modified either with gentamicin...
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublicationThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
High-Temperature Tensile Behaviour of GTAW Joints of P92 Steel and Alloy 617 for Two Different Fillers
PublicationThis study explores the high-temperature (HT) tensile rupture characteristics of a dissimilar gas-tungsten-arc-welded (GTAW) joint between P92 steel and Alloy 617, fabricated using ER62SB9 and ERNiCrCoMo-1 fillers. The high-temperature tensile tests were performed at elevated temperatures of 550 ◦C and 650 ◦C. An optical microscope (OM) and a field emission scanning electron microscope (FESEM) were utilized to characterize the...
-
Addressing Challenges in AI-based Systems Development: A Proposal of Adapted Requirements Engineering Process
Publication[Context] Present-day IT systems are more and more dependent on artificial intelligence (AI) solutions. Developing AI-based systems means facing new challenges, not known for more conventional systems. Such challenges need to be identified and addressed by properly adapting the existing development and management processes. [Objective] In this paper, we focus on the requirements engineering (RE) area of IT projects and aim to propose...
-
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublicationThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
Dependence of Housing Real Estate Prices on Inflation as One of the Most Important Factors: Poland’s Case
PublicationThe study aimed to examine the impact of inflation on the real estate market using Polish panel data for the last 13 years. It is based on a panel model, where price changes of one square meter of housing are determined as a function in changes of inflation, the central bank's base rate, dwellings built, as well as new mortgage loans. The quarterly dynamics of the average price of 1 square meter of housing in...
-
Techno‐economic evaluation of a natural deep eutectic solvent‐based biorefinery: Exploring different design scenarios
PublicationThis paper presents a comprehensive techno‐economic evaluation of an integrated natural deep eutectic solvent (NADES)‐based biorefinery – a 1 ton day−1 capacity design plant. The key parameters include payback period, net present value (NPV), and internal rate of return (IRR). These were compared with the parameters of conventional biorefineries. The ‘n th plant’ results clearly revealed that the single product‐based biorefinery...
-
Effect of Flow Normalization in Micro-Pin-Finned Heat Sink: Numerical Study
PublicationThe micro-pin-fin heat sink (MPFHS) is widely employed for the heat transfer enhancement of microchannel heat sinks. In the current paper, the effect of flow normalization on the thermohydraulic performance of micro-pin-finned heat sinks is studied numerically. Two geometries of MPFHSs, the conventional design micro-pin-fin heat sink (CD-MPFHS) with a uniform-width micro pin fin and the proposed design micro-pin-fin heat sink (PD-MPFHS)...
-
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublicationAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
Cattaneo–Christov heat flow model for copper–water nanofluid heat transfer under Marangoni convection and slip conditions
PublicationThis report is devoted to the study of the flow of MHD nanofluids through a vertical porous plate with a temperature-dependent surface tension using the Cattaneo–Christov heat flow model. The energy equation was formulated using the Cattaneo–Christov heat flux model instead of Fourier’s law of heat conduction. The Tiwari–Das model was used to take into account the concentration of nanoparticles when constructing the momentum equation....
-
Research on Linear Actuators for Active Foil Bearings
PublicationActive foil bearings are a kind of gas foil bearing. They contain actuators which allow for modification of the bearing sleeve size and the shape of the lubrication gap. Rotor vibrations can be actively controlled by these changes. It is possible, among other things, to reduce the starting torque, control the vibration amplitude at different speeds and improve operational safety. Prototypes of active foil bearings are being developed...
-
The origins of the brick architecture in Pomerania
PublicationTraditionally, brick is one of the most popular building materials on the southern coast of the Baltic Sea. Although the origins of brick architecture have been the subject of numerous research studies, their results were focused on the Kingdom of Denmark, merchant-towns and the State of the Teutonic Order. Most scholars claimed that Pomeranian architecture had not been as developed as that in the neighbouring countries. Moreover,...
-
Language material for English audiovisual speech recognition system developmen . Materiał językowy do wykorzystania w systemie audiowizualnego rozpoznawania mowy angielskiej
PublicationThe bi-modal speech recognition system requires a 2-sample language input for training and for testing algorithms which precisely depicts natural English speech. For the purposes of the audio-visual recordings, a training data base of 264 sentences (1730 words without repetitions; 5685 sounds) has been created. The language sample reflects vowel and consonant frequencies in natural speech. The recording material reflects both the...
-
CURRENT TRENDS IN RECYCLING OF PHOTOVOLTAIC SOLAR CELLS AND MODULES WASTE
PublicationIn comparison to other energy producing techniques, photovoltaics (PV) is one of the most promising options: no emission of any matter into the environment during operation; extremely long operation period (estimated average: 25 years), minimum maintenance, robust technique, aesthetic aspects. The use of photovoltaics is rapidly increasing, and the respective market is developing accordingly. Although PV manufacturing equipment...
-
Recycling of Photovoltaic Solar Cells and Modules - Te State - Of - Art
PublicationIn comparison to other energy producing techniques, photovoltaics (PV) is one of the most promising options: no emission of any matter into the environment during operation; extremely long operation period (estimated average: 25 years), minimum maintenance, robust technique, aesthetic aspects. The use of photovoltaics is rapidly increasing, and the respective market is developing accordingly. Although PV manufacturing equipment...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes - experimental study
PublicationIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. The aim of this paper is to investigate experimentally the behaviour of horizontally deformed columns (deformation...
-
Chiral Schiff base complexes as an effective catalyst in Diels-Alder reaction
PublicationDiels Alder reaction is a very important tool in carbon-carbon bond formation. It is a cycloaddition between a conjugated diene and a second compound called dienophile. Where one or more heteroatoms are present in the diene and/or dienophile framework, the cycloaddition is called hetero-Diels-Alder reaction (HDA). The asymmetric Diels-Alder reaction is among the most powerful available methodologies for that construction of optically...
-
Simulation model for evaluation of QOS dynamic routing
PublicationCurrent informational networks use a large variety of technologies to support data exchange. Most of them are focused on IP protocol and include mechanisms which by definition should supply demanded QoS. One of those mechanisms is efficient path calculation - routing. Traffic offered to the network can change very rapidly in short term. Routing should support such traffic changes and all the time calculate valid paths in terms...
-
Investigation of the electrochemical behaviour of AA1050 aluminium alloy in aqueous alkaline solutions using Dynamic Electrochemical Impedance Spectroscopy
PublicationThe paper presents the electrochemical behaviour of aluminium alloy AA1050 in aqueous alkaline media in the pH range 14–8.5. Electrochemical study was applied in order to obtain comprehensive information on the mechanism and kinetics of the process of anodic dissolution of aluminium, supplemented by monitoring of surface topography using an electron microscope. The corrosion rate of AA1050 increases with increasing concentration...
-
Application of artificial intelligence into/for control of flexible manufacturing cell
PublicationThe application of artificial intelligence in technological processes control is usually limited. One problem is how to respond to changes in the environment of manufacturing system. A way to overcome the above shortcoming is to use fuzzy logic for representation of the inexact information. In this paper fundamentals of artificial intelligence and fuzzy logic are introduced from a theoretical point of view. Still more the fuzzy...
-
The influence oil additives on spread cracks in silicon nitride
PublicationThe paper presents an experimental study of the influence of oil additives (Cl, S, P, cerium dioxide (CeO2)) on spread cracks in silicon nitride. The additives Cl, S, P are bound in molecules in liquid form soluble in the base oil. The CeO2 is purely in powder form in suspension. The use of CeO2 powder was made based on the good results of polishing of silicon nitride. A ceramic angular contact ball bearing was modelled using a...
-
The Impact of Homogeneity of High Modulus Asphalt Concrete Layer on Low-Temperature Cracking
PublicationDuring winter season of 2012 numerous transverse cracks developed in high-modulus asphalt concrete (HMAC) base of newly constructed motorway. Pavement cracked both in transverse joint locations and in the area between them. Research which was conducted during investigation of the causes and mechanisms of cracking consisted of: field examination, laboratory testing of specimens cored out of the existing pavement, computational analyses...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublicationDiagnosis of damage in civil engineering structures has recently become an important issue in the safety assessment procedure. Among a number of different approaches, a method of measuring the changes in natural frequencies is one of the most effective indicators of global damage. It has been successfully applied to relatively small. structures, however, the tests on large structures are very difficult and the practical application...
-
C-1311 (Symadex), a potential anti-cancer drug, intercalates into DNA between A and G moieties. NMR-derived and MD-refined stereostructure of the d(GAGGCCTC) 2 :C-1311 complex
PublicationImidazoacridinone C-1311 (Symadex®) is an antitumor agent which has been recommended for Phase II clinical trials a few years ago. Previously, it was shown experimentally that during the initial stage of its action C-1311 forms stable intercalation complexes with DNA duplexes. Herein, a NMR-derived stereostructure of d(GAGGCCTC)2:C-1311 complex was reported. The ligand was found locating itself between A and G moieties, forming...
-
Corrosion process monitoring by AFM higher harmonic imaging
PublicationThe atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever...
-
Application of soil nailing technique for protection and preservation historical buildings
PublicationSoil nailing is one of the recent in situ techniques used for soil improvement and in stabilizing slopes. The process of soil nailing consists of reinforcing the natural ground with relatively small steel bars or metal rods, grouted in the pre-drilled holes. This method has a wide range of applications for stabilizing deep excavations and steep slopes. Soil nailing has recently become a very common method of slope stabilisation...
-
Study of pH and temperature effect on lipophilicity of catechol-containing antioxidants by reversed phase liquid chromatography
PublicationLipophilicity of selected antioxidant phytochemicals, including flavonoids, phenolic acids and xanthonoids, was determined by reversed phase high performance liquid chromatography with UV detection (RP-HPLC-UV). The analyses run at different temperature and pH conditions in isocratic mode suggested that lipophilicity as distribution coefficient (logD) between aqueous and organic phase decreases with increasing temperature. For...
-
Assessment of the Accuracy of Determining the Angular Position of the Unmanned Bathymetric Surveying Vehicle Based on the Sea Horizon Image
PublicationThe paper presents the results of research on assessing the accuracy of angular position measurement relative to the sea horizon using a camera mounted on an unmanned bathymetric surveying vehicle of the Unmanned Surface Vehicle (USV) or Unmanned Aerial Vehicle (UAV) type. The first part of the article presents the essence of the problem. The rules of taking the angular position of the vehicle into account in bathymetric surveys...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublicationThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
Galerkin Finite Element Process for Entropy Production and Thermal Evaluation of Third-Grade Fluid Flow: A Thermal Case Study
Publication: A fluid’s moving class improves its heat transmission capability, as well as its rigidity, owing to multivariate molecule suspension. In this way, nanofluids are superior to common fluids. In this study, we evaluated the features of ease and heat transfer. Furthermore, we investigated permeable media, heat source, variable heat conductivity, and warm irradiation results. A mathematical technique known as the Galerkin finite element...
-
How acidic amino acid residues facilitate DNA target site selection
PublicationDespite the negative charge of the DNA backbone, acidic residues (Asp/Glu) commonly participate in the base readout, with a strong preference for cytosine. In fact, in the solved DNA/protein structures, cytosine is recognized almost exclusively by Asp/Glu through a direct hydrogen bond, while at the same time, adenine, regardless of its amino group, shows no propensity for Asp/Glu. Here, we analyzed the contribution of Asp/Glu...
-
Simple Millimeter Wave Identification System Based on 60 GHz Van Atta Arrays
PublicationThe paper presents a proof-of-concept of a millimeter-wave identification system based on Van Atta array tags in the 60 GHz band. For interrogation of the tags, a vector network analyzer and a measurement transceiver were employed in alternative test configurations. The design, fabrication and measurements of co- and cross-polarized Van Atta arrays are presented in the paper. They can be treated as simple chipless RFID tags with...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublicationTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Effect of Tool Positioning Factors on the Strength of Dissimilar Friction Stir Welded Joints of AA7075-T6 and AA6061-T6
PublicationFriction Stir Welding (FSW) is a solid-state bonding technique. There are many direct and indirect factors affecting the mechanical and microstructural properties of the FSW joints. Tool offset, tilt angle, and plunge depth are determinative tool positioning in the FSW process. Investigating the effect of these factors simultaneously with other parameters such as process speeds (rotational speed and translational speed) and tool...
-
Highly effective asphaltene-derived adsorbents for gas phase removal of volatile organic compounds
PublicationA novel nitrated asphaltene-derived adsorbent (Asf-Nitro) was prepared using facile isolation and modification procedures. The successful modification was confirmed by Fourier-transform infrared spectroscopy (FTIR). The nitrated adsorbent was evaluated in terms of dispersive and specific interactions, Lewis acid-base properties and adsorption isotherms by means of inverse gas chromatography (IGC). Nitration was found to be extremely...
-
The Positioning Accuracy of BAUV Using Fusion of Data from USBL System and Movement Parameters Measurements
PublicationThe article presents a study of the accuracy of estimating the position coordinates of BAUV (Biomimetic Autonomous Underwater Vehicle) by the extended Kalman filter (EKF) method. The fusion of movement parameters measurements and position coordinates fixes was applied. The movement parameters measurements are carried out by on-board navigation devices, while the position coordinates fixes are done by the USBL (Ultra Short Base...
-
Forced degradation studies of ivabradine and in silico toxicology predictions for its new designated impurities
PublicationAll activities should aim to eliminate genotoxic impurities and/or protect the API againstdegradation. There is a necessity to monitor impurities from all classification groups,hence ivabradine forced degradation studies were performed. Ivabradine was provedto be quite durable active substance, but still new and with insufficient stability data.Increased temperature, acid, base, oxidation reagents and...
-
Low temperature broad band dielectric spectroscopy of multiferroic Bi6Fe2Ti3O18 ceramics
PublicationIn the present research the tool of broadband dielectric spectroscopy was utilized to characterize dielectric behavior of Bi6Fe2Ti3O18 (BFTO) Aurivillius-type multiferroic ceramics. Dielectric response of BFTO ceramics was studied in the frequency domain (Δν=0.1Hz – 10MHz) within the temperature range ΔT=-100°C – 200°C. The Kramers-Kronig data validation test was employed to validate the impedance data measurements and it was found...
-
The interactions of monomeric acridines and unsymmetrical bisacridines (UAs) with DNA duplexes: an insight provided by NMR and MD studies
PublicationMembers of a novel class of anticancer compounds, exhibiting high antitumor activity, i.e. the unsymmetrical bisacridines (UAs), consist of two heteroaromatic ring systems. One of the ring systems is an imidazoacridinone moiety, with the skeleton identical to the structural base of Symadex. The second one is a 1-nitroacridine moiety, hence it may be regarded as Nitracrine’s structural basis. These monoacridine units are connected...
-
Speed estimation of a car at impact with a W-beam guardrail using numerical simulations and machine learning
PublicationThis paper aimed at developing a new method of estimating the impact speed of a passenger car at the moment of a crash into a W-beam road safety barrier. The determination of such a speed based on the accident outcomes is demanding, because often there is no access to full accident data. However, accurate determination of the impact speed is one of the key elements in the reconstruction of road accidents. A machine learning algorithm...
-
Magnetoelectric, spectroscopic, optical and elastic properties of Co-doped BaTiO3 ceramics
Publicationhe BaTiO3 perovskite is widely used in the electronic technology due to its dielectric, piezoelectric and ferroelectric properties and is a well-known base for obtaining a promising multifunctional material. In this paper we report the extensive studies on the Co-doped BaTiO3 ceramics for the wide range cobalt content. Full structural characterization of studied samples in a 20–450 K range was provided. The results of research...
-
Sources and composition of chemical pollution in Maritime Antarctica (King George Island), part 2: Organic and inorganic chemicals in snow cover at the Warszawa Icefield
PublicationThe study area is located on King George Island, where 90% of the area is permanently glaciated. This study provides a comprehensive analysis of the inorganic and organic chemistry of snow cover in the icefield and a comparison against previous results obtained in fresh water. Snow samples were collected in the summer of 2017 in the Warszawa Icefield area. Sampling points are located along two transects: between the Arctowski Polish...
-
Interactions of telomeric proteins with nucleic acids: sequence recognition on intact and oxidatively damaged telomeres
PublicationTelomeres are complex nucleoprotein assemblies that play a vital role in the maintenance of functional ends of linear chromosomes. Telomeric DNA, composed of tandem repeats of the 5'-TTAGGG-3' motif, solves the so-called end replication problem: as chromosomes shorten with each cell division, no information is lost, and the telomere can be re-extended. In the cell, many protein factors regulate telomere length, nuclear positioning...
-
Behaviour of asymmetric structures with base isolation made of Polymeric Bearings
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. During the last few years alone, the world has witnessed many major earthquakes, five of which have caused far-reaching consequences of a national scale for Haiti (January 2010), Chile (February...
-
Miniaturization of ESPAR Antenna Using Low-Cost 3D Printing Process
PublicationIn this paper, the miniaturized electronically steerable parasitic array radiator (ESPAR) antenna is presented. The size reduction was obtained by embedding its active and passive elements in polylactic acid (PLA) plastic material commonly used in low-cost 3D printing. The influence of 3D printing process imperfections on the ESPAR antenna design is investigated and a simple yet effective method to...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes: numerical analysis
PublicationIt has been observed during earthquakes that the so called soft-storey failure of an upper floor of a building leads to considerable vertical impact load acting on structural members of the lower storeys. The aim of this paper is to investigate numerically the behaviour of horizontally deformed columns (deformation as the result of earthquake loading) that are additionally subjected to vertical impact load. In the first stage of...