Filters
total: 424
filtered: 337
Search results for: skauting
-
Multispectral impedance quality testing of coil-coating system using principal component analysis
PublicationThe task of quality checking of the coil-coated system was undertaken using impedance spectroscopy. In order to properly characterize the system the new impedance spectrum was calculated as an averaged result of 12 experimental spectra obtained from 12 different places of the sample at the same time of immersion in 3% of NaCl. The experimental spectra were recorded for a 24-h period at 1 h intervals between starting points of each...
-
Interaction Between Storm Water Conduit Flow and Overland Flow for Numerical Modelling of Urban Area Inundation
PublicationNowadays we can observe increasing frequency of inundations in cities. This makes accurate predicting of inundations more important than ever. Numerical modeling of this issue requires complex approach with simultaneous calculations of pipe flow and surface flow. In this paper, after a short review of known methods used for solving pipe and surface flow, we will try to answer the question if presented methods would be sufficiently...
-
Propagation of acoustic pulses in some fluids with yield stress
PublicationThis study is devoted to the derivation of approximate equations governing acoustic pulses in flows with yieldstress, including some time-dependent flows with a slow dependence on time of yield stress and apparent viscosity. Themodeling of yield stress and apparent viscosity in the vicinity of a zero deformation rate allows us to consider a thixotropicfluid as a Bingham plastic with coefficients that are dependent on time. The...
-
The Use of Gravimetric Measurements to Determine the Orthometric Height of the Benchmark in the Port of Gdynia
PublicationThis paper contains a description of the technology used to make gravimetric measurements of the height of a reference point located in the Port of Gdynia, Poland. Measurements were made using a CG-5 gravimeter manufactured by LaCoste & Romberg Scintrex Inc., and determinations of position used a Leica Viva GS15 receiver integrated with a network of HxGN SmartNet GNSS reference stations. The measuring methodology required gravimeter...
-
The life cycle cost of a building from the point of view of environmental criteria of selecting the most beneficial offer in the area of competitive tendering
PublicationThe article analyses environmental and ecological criteria of selecting the most beneficial offer in the aspect of LCC. Construction works contracts and the potential method of defining the above criteria, among others, is pondered on (for example by the recommendation of a material, which is supposed to be used, a ban on substances that are harmful for human health as well for the environment). In the relation to the above, it...
-
Collision-free network exploration
PublicationMobile agents start at different nodes of an n-node network. The agents synchronously move along the network edges in a collision-free way, i.e., in no round two agents may occupy the same node. An agent has no knowledge of the number and initial positions of other agents. We are looking for the shortest time required to reach a configuration in which each agent has visited all nodes and returned to its starting location. In...
-
Application of deep eutectic solvents in atomic absorption spectrometry
PublicationAtomic absorption spectrometry (AAS) is a widely applied technique for metal quantification due to its practicality, easy use and low cost. However, to improve the metrological characteristics of AAS, in particular the sensitivity and the detection limit, sample pretreatment is commonly used before the detection step itself. In consideration of the principles of Green Analytical Chemistry, new solvents are being introduced into...
-
A model of the response of the MGS-6 gravity sensor to tilting
PublicationThe reliable interpretation of the measurements made by the Micro-g marine gravimetric system (MGS-6) depends on how the temporary changes of the scale coefficients such as gravimeter scale factor, vertical cross-coupling (VCC) effect, tiltmeter cross and tiltmeter long are compensated for during the signal analysis. The listed coefficients cannot be determined from readings during the measurements or by analysing the final data....
-
Identification of residual force in static load tests on instrumented screw displacement piles
PublicationOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...
-
Isocyanate-Free Polyurethanes
PublicationIsocyanate-free polyurethanes (also called non-isocyanate polyurethanes, or NIPUs) are alternatives to the conventional (commercially used) polyurethanes synthesized using di- or polyisocyanates, polyols, and chain extenders with low molecular weight. The major routes of NIPUs’ synthesis involve polyaddition of cyclic carbonates and di- or polyamines, polycondensation of carbamates, and diols. The most important intermediates are...
-
Light-Powered Starter for Micro-Power Boost DC–DC Converter for CMOS Image Sensors
PublicationThe design of a starter for a low-voltage, micro-power boost DC–DC converter intended for powering CMOS image sensors is presented. A unique feature of the starter is extremely low current, below 1 nA, supplying its control circuit. Therefore, a high-voltage (1.3 V) configuration of series-connected photovoltaic diodes available in a standard CMOS process or a small external LED working in photovoltaic mode can be used as an auxiliary...
-
Effect of solar radiation on current-carrying capacity of PVC-insulated power cables – the numerical point of view
PublicationPower cables are usually buried in the soil, which results in their relatively high current-carrying capacity. However, there are cases in which the starting/final section of a cable line runs along a pole of an overhead power line. Power cables can be directly exposed to solar radiation then, and this negatively influences their current-carrying capacity as well as estimated life of the cables’ insulation. An analysis of thermal...
-
Partial dominated schedules and minimizing the total completion time of deteriorating jobs
PublicationA problem of scheduling deteriorating jobs on a single processor is considered. The processing time of a job is given by a function pi=ai+bisi, where si is the starting time of the job, ai>=0, bi>=0, for i=1,...,n. Jobs are non-preemptive and independent and there are neither ready times nor deadlines. The goal is to minimize the total weighted completion time. We show how to employ the concept of non-dominated schedules to construct...
-
Fast surrogate-assisted simulation-driven design of compact microwave hybrid couplers
PublicationThis work presents a robust methodology for expedited simulation-driven design optimization of compact microwave hybrid couplers. The technique relies on problem decomposition, and a bot-tom–up design strategy, starting from the level of basic building blocks of the coupler, and finishing with a tuning procedure that exploits a fast surrogate model of the entire structure. The latter is constructed by cascading local response surface...
-
Bounds on the cover time of parallel rotor walks
PublicationThe rotor-router mechanism was introduced as a deterministic alternative to the random walk in undirected graphs. In this model, a set of k identical walkers is deployed in parallel, starting from a chosen subset of nodes, and moving around the graph in synchronous steps. During the process, each node successively propagates walkers visiting it along its outgoing arcs in round-robin fashion, according to a fixed ordering. We consider...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part III. Diagnostic and operating tolerances
PublicationThe third part of the article presents a method for detecting failures of the automatic engine control system with the aid of an exhaust gas temperature setter, specially designed and machined for this purpose. It also presents a procedure of identifying the operating tolerances and determining the diagnostic tolerances for the exhaust gas temperature recorded in the naval turbine engine during the start-up and acceleration processes....
-
Searching of the buried objects in the sea bottom by means of noninvasive methods
PublicationSearching of objects on the seabed or under its surface currently is a challenge for a number of researchers interested in the sea bottom. The problem relates to the objects on the depths of up to several tens of meters from the surface of the seabed. Finding the objects is the subject of interest for a wide group of users starting from archaeologists, and ending on groups interested in marine safety, as well as in military application...
-
Local properties of organic coatings close to glass transition temperature
PublicationAcrylic coating applied on copper substrate has been investigated at different temperatures starting from the ambient one up to the level above the glass transition temperature. Its local topographic and electric properties have been examined with the atomic force microscopy (AFM) based approach including dc current mapping and local impedance spectroscopy. The local findings have been compared with the information from global...
-
Proceedings of the 9th International Conference on Structural Dynamics, EURODYN 2014
PublicationSince offshore wind turbine supporting structures are subjected to dynamic environments with time-varying loading conditions, it is important to model their dynamic behavior and validate these models by means of vibrational experiments. In this paper assessment of dynamical state of the structure is investigated by means of both: numerical modeling, and experimental modal analysis. In experimental modal analysis, capturing the...
-
Extended Reflexive Ontologies for the Generation of Clinical Recommendations
PublicationDecision recommendations are a set of alternative options for clinical decisions (e.g., diagnosis, prognosis, treatment selection, follow-up, and prevention) that are provided to decision makers by knowledge-based Clinical Decision Support Systems (k-CDSS) as aids. We propose to follow a ‘‘reasoning over domain’’ approach for the generation of decision recommendations by gathering and inferring conclusions from production rules....
-
Collaborative planning? Not yet seen in Poland. Identifying procedural gaps in the planning system 2003–2023
PublicationCollaborative planning aims to increase the legitimacy of decision-making in spatial development. In this approach, planning involves debate and engagement in discourse, and participation and interaction between actors are thus at the heart of the planning process. This article examines whether the planning system in Poland as defined for the period 2003–2025 provides a level of participation and deliberation and other qualities...
-
Multi-objective optimization of compact UWB impedance matching transformers using Pareto front exploration and adjoint sensitivities
PublicationIn this paper, a technique for fast multi-objective optimization of impedance matching transformers has been presented. In our approach, a set of alternative designs that represent the best possible trade-offs between conflicting objectives (here, the maximum reflection level within a frequency band of interest and the circuit size) is identified by directly exploring the Pareto front. More specifically, the subsequent Pareto-optimal...
-
Deep Eutectic Solvents and Their Uses for Air Purification
PublicationChemical compounds released into the air by the activities of industrial plants and emitted from many other sources, including in households (paints, waxes, cosmetics, disinfectants, plastic (PVC) flooring), may affect the environment and human health. Thus, air purification is an important issue in the context of caring for the condition of the environment. Deep eutectic solvents (DESs) as liquids with environmentally friendly...
-
Proces wytwarzania e-kursu. Studium przypadku.
PublicationArtykuł definiuje proces wytwarzania e-kursu i e-lekcji oraz kolejne jego etapy, zaczynając od okre - ślania celu i odbiorcy, a kończąc na udostępnieniu treści. Na podstawie opisanego procesu przedstawiane jest stu - dium przypadku dla e-kursu prowadzonego na studiach zaocznych na Wydziale ETI Politechniki Gdańskiej na przedmiocie Strategie informatyzacji. Artykuł pokazuje też ewaluację studium przypadku, zarówno na poziomie oceny...
-
Principles of smoking
PublicationTreatment of a large variety of foods with wood smoke has been practiced for centuries—predominantlymeats, poultry, and fish, but also scallops, cheeses, prunes, paprika, and themalt used to produce whiskey and some sorts of beer.The process usually includes salting and partial drying; it may also be coupled with heating. The aim is to increase the shelf life of the products, prevent food poisoning, and add a desirable smoky flavor....
-
Quantum security and theory of decoherence
PublicationWe sketch a relation between two crucial, yet independent, fields in quantum information research, viz. quantum decoherence and quantum cryptography. We investigate here how the standard cryptographic assumption of shielded laboratory, stating that data generated by a secure quantum device remain private unless explicitly published, is disturbed by the einselection mechanism of quantum Darwinism explaining the measurement process...
-
Adsorption behavior and corrosion inhibitive characteristics of newly synthesized cyano-benzylidene xanthenes on copper/sodium hydroxide interface: Electrochemical, X-ray photoelectron spectroscopy and theoretical studies
PublicationElegant process for synthesis of 3-(7H-dibenzo[c,h]xanthen-7-yl)benzaldehyde (3), as new starting material to create a set of novel xanthene analogues, 2-(3-(7H-dibenzo[c,h]xanthen-7-yl)benzylidene)malononitrile (4), 3-(3-(7H-dibenzo[c,h]xanthen-7-yl)phenyl)-2-cyanoacrylic acid (5), and Ethyl-3-(3-(7H-dibenzo[c,h]xanthen-7-yl)phenyl)-2-cyanoacrylate (6), was achieved starting with available materials under mild conditions. Various...
-
RESEARCH OF HYDRAULIC PISTON PUMPS’ START-UP IN LOW AMBIENT TEMPERATURES
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of increase of resistance of cold oil flow in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump...
-
MATCHED FILTER APPROACH FOR MICROSEISMIC SIGNAL PROCESSING OF REAL DATA FROM EAST POMERANIA SHALE GAS
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing (HF)process. An array of several hundred geophones is placed on the surface to record little ground tremors induced by fracturing process. Filtration and summation of signals from geophones is essential to identify and locate fracturing events from underground. Authors propose a method of matched filtering, that is usually...
-
Review of the Usefulness of Various Rotational Seismometers with Laboratory Results of Fibre-Optic Ones Tested for Engineering Applications
PublicationStarting with descriptions of rotational seismology, areas of interest and historical field measurements, the fundamental requirements for rotational seismometers for seismological and engineering application are formulated. On the above basis, a review of all existing rotational seismometers is presented with a description of the principles of their operation as well as possibilities to fulfill formulated requirements. This review...
-
Reliable Multi-Stage Optimization of Antennas for Multiple Performance Figures in Highly-Dimensional Parameter Spaces
PublicationDesign of modern antenna structures needs to account for multiple performance figures and geometrical constraints. Fulfillment of these calls for the development of complex topologies described by a large number of parameters. EM-driven tuning of such designs is mandatory yet immensely challenging. In this letter, a new framework for multi-stage design optimization of multi-dimensional antennas with respect to several performance...
-
Some Security Features of Selected IoT Platforms
PublicationIoT (Internet of Things) is certainly one of the leading current and future trends for processing in the current distributed world. It is changing our life and society. IoT allows new ubiquitous applications and processing, but, on the other hand, it introduces potentially serious security threats. Nowadays researchers in IoT areas should, without a doubt, consider and focus on security aspects. This paper is aimed at a high-level...
-
On dynamic modeling of piezomagnetic/flexomagnetic microstructures based on Lord–Shulman thermoelastic model
PublicationWe study a time-dependent thermoelastic coupling within free vibrations of piezomagnetic (PM) microbeams considering the flexomagnetic (FM) phenomenon. The flexomagneticity relates to a magnetic field with a gradient of strains. Here, we use the generalized thermoelasticity theory of Lord–Shulman to analyze the interaction between elastic deformation and thermal conductivity. The uniform magnetic field is permeated in line with...
-
Simulations of the Derecho Event in Poland of 11th August 2017 Using WRF Model
PublicationThis series contains datasets related to the forecasting of a severe weather event, a derecho, in Poland on 11 August 2017. The simulations were conducted using the Weather Research and Forecasting (WRF) model version 4.2.1 with different initial and boundary conditions of the pressure and model levels derived from 5 global models: Global Forecast System (GFS), Global Data Assimilation System (GDAS), European Centre for Medium-Range...
-
Various cases of preservation and adaptive reuse Heritage Buildings in the Port of Gdynia
PublicationThe port of Gdynia contains a diverse range of heritage assets, starting with its spatial layout which is an urban concept designed in the first half of the 1920s. It is important to point out, this historically-shaped harbor space is preserved in its general idea and still functioning in port activities. Another significant element is the structural, technological solution which was the basis for constructing the entire port area...
-
Progress in used tyres management in the european union: a review
PublicationThe dynamic increase in the manufacture of rubber products, particularly those used in the automobile industry, is responsible for a vast amount of wastes, mostly in the form of used tyres, of which more than 17 million tonnes are produced globally each year. The widely differing chemical compositions and the cross-linked structures of rubber in tyres are the prime reason why they are highly resistant to biodegradation, photochemical...
-
Pressure-induced phase transitions in LnTe (Ln=La, Gd, Ho, Yb) and AmTe
PublicationThe structural behaviour under compression of different lanthanide (La, Gd, Ho, Yb) and actinide (Am) monochalcogenides is studied by means of in situ high-pressure x-ray diffraction. All the investigated compounds crystallize at ambient conditions within a cubic (B1) NaCl-type structure but show different behaviours at high pressures. LaTe and AmTe undergo B1 to B2 (CsCl-type structure) phase transitions, starting at 9 GPa and...
-
Modeling of traffic safety indictors on Polish national road network
PublicationAlthough decreased from 2001 to 2013, Poland’s road deaths improved at a slower rate than the rest of the EU, leaving Poland as one of the worst road safety performing countries in the EU. The national road network in Poland, despite the dynamic transformation and development, still does not conform to the EU safety standards. Similar situation exists in other EU countries, particularly those in Central and Eastern Europe. Safety...
-
Integrate-and-fire models with an almost periodic input function
PublicationWe investigate leaky integrate-and-fire models (LIF models for short) driven by Stepanov and μ-almost periodic functions. Special attention is paid to the properties of the firing map and its displacement, which give information about the spiking behavior of the considered system. We provide conditions under which such maps are well-defined and are uniformly continuous. We show that the LIF models with Stepanov almost periodic...
-
Decontaminating Arbitrary Graphs by Mobile Agents: a Survey
PublicationA team of mobile agents starting from homebases need to visit and clean all nodes of the network. The goal is to find a strategy, which would be optimal in the sense of the number of needed entities, the number of moves performed by them or the completion time of the strategy. Currently, the field of distributed graph searching by a team of mobile agents is rapidly expanding and many new approaches and models are being presented...
-
Creating Hotel Services from a Perspective of Extraordinary Customer Experience
PublicationThis conceptual article aims to explore the process of providing hotel services in the context of requirements arising from the experience economy. Both the concept of experience marketing and the concept of customer experience management provided a theoretical framework for the discussion. Based on a review of literature and conclusions derived from hotel managers’ experiences, a research model is proposed, which may be of some...
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublicationThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Rheological characteristics of oligomeric semiproducts gained via chemical degradation of polyurethane foam using crude glycerin in the presence of different catalysts
PublicationPolyurethane (PU) recycling is a topic of growing interest due to the increasing amount of polyurethane waste. The main purpose of polyurethane chemical recycling is to recover the starting polyol. In this study, a method of polyurethane thermochemical recycling, glycerolysis by means of crude glycerin, is proposed. This work presents a comparative study of commercial catalysts used in order to accelerate the decomposition process,...
-
Modeling of Electrodynamic Phenomena in an Ultra-Rapid Inductive–Dynamic Actuator as Applied to Hybrid Short-Circuit Breakers - A Review Study
PublicationThis article is a study of the research development of electrodynamic phenomena occurring in ultra-fast electrodynamic drives. These types of linear drives are among the fastest, not only because of the huge accelerations achieved, but, above all, because of the extremely short reaction time. For this reason, electrodynamic drives are used in hybrid short-circuit breakers. The phenomena occurring in this type of drive are actually...
-
New procedure for the examination of the degradation of volatile organonitrogen compounds during the treatment of industrial effluents
PublicationWe present a new procedure for the determination of 32 volatile organonitrogen compounds in samples of industrial effluents with a complex matrix. The procedure, based on dispersive liquid–liquid microex-traction followed by gas chromatography with nitrogen-phosphorus and mass spectrometric detection, wasoptimized and validated. Optimization of the extraction included the type of extraction and disperser sol-vent, disperser solvent...
-
Modelling of Longitudinal Elastic Wave Propagation in a Steel Rod Using the Discrete Element Method
PublicationThe paper deals with the issue of modelling elastic wave propagation using the discrete element method (DEM). The case of a longitudinal wave in a rod with a circular cross-section was considered. A novel, complex algorithm consisting of the preparation of models and simulation of elastic waves was developed. A series of DEM models were prepared for simulations, differing in discretisation and material parameters. Additional calculations...
-
Nowoczesne metody termografii w systemie monitorowania stanu sieci przesyłowych
PublicationW artykule przedstawiono obecnie stosowane metody inspekcji termowizyjnej, skupiając się na prewencyjnej diagnostyce stanu sieci przesyłowej. Badanie termowizyjne ma różne wymiary wpływu na efektywność energetyczną. Z jednej strony wykorzystuje się ją do inspekcji szczelności termoizolacji budynków, wpływając na świadomość, że „najtańsza energia to ta zaoszczędzona”, z drugiej strony jest narzędziem dla operatorów sieci dystrybucyjnych...
-
Determination of Pesticide Residues in Honeybees using Modified QUEChERS Sample Work-Up and Liquid Chromatography-Tandem Mass Spectrometry
PublicationIncreasing emissions of chemical compounds to the environment, especially of pesticides, is one of factors that may explain present honeybee colony losses. In this work, an analytical method employing liquid chromatography-tandem mass spectrometry (LC-MS/MS) was optimized for the simultaneous screening of 19 pesticides which have not been yet determined in honeybee samples from northern Poland (Pomerania). The sample preparation,...
-
An electronic nose based on the semiconducting and electrochemical gas sensors
PublicationThe practical application of human nose for fragrance recognition is severely limited by the fact that our sense of smell is subjective and gets tired easily. Consequently, there is a significant need for an instrument that can be a substitution of the human sense of smell. Development of an electronic nose devices is an active area of research starting from pioneering research of Dodd and Persuad in the mid-1980s. Such systems...
-
Two-Step Model Based Adaptive Controller for Dissolved Oxygen Control in Sequencing Wastewater Batch Reactor
PublicationDissolved Oxygen (DO) concentration is a crucial parameter for efficient operation of biological processes taking place in the activated sludge Wastewater Treatment Plant (WWTP). High-quality DO control is difficult to achieve because of complex nonlinear behavior of the plant and substantial influent disturbances. A method to improve the Direct Model Reference Adaptive Control (DMRAC) technology in application to DO tracking for...