displaying 1000 best results Help
Search results for: STABILIZING FORCE
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublicationIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublicationIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Evaluation of the prediction ability of air pollutants based on the electronic nose responses
PublicationElectronic noses are able to perform on-line measurements of the toxic volatile compounds in air. Due to their low cost and compact size they can be placed in the areas exposed to pollution, outside the laboratory. Those advantages, on the other side, force the need for development of the reliable sensors data analysis procedures. One of the most important issues connected with electronic noses is the lack of stability of the gas...
-
Crystal structures of aminotransferases Aro8 and Aro9 from Candida albicans and structural insights into their properties
PublicationAminotransferases catalyze reversibly the transamination reaction by a ping-pong bi-bi mechanism with pyridoxal 5′-phosphate (PLP) as a cofactor. Various aminotransferases acting on a range of substrates have been reported. Aromatic transaminases are able to catalyze the transamination reaction with both aromatic and acidic substrates. Two aminotransferases from C. albicans, Aro8p and Aro9p, have been identified recently, exhibiting...
-
Wzbudzone siły wewnętrzne : skutki upr0szczonego modelowania zakrzywionej estakady sprężonej
Publicationthe paper presents problems, which were encountered during the construction of a southern road bypass of city gdansk. after prestressing and removing formwork, the contractor spotted, that some of outer bearings are detached. performed analysis showed that, this situation was caused by the usage of a simplified, straight beam model during design phase. the paper shows the influence of a curved in plane prestressed system on internal...
-
Synthesis of Novel Polycationic Quaternary Di- and Trispirocyclic Benzenes
PublicationTreatment of hexakis(bromomethyl)benzene with a cyclic amine {morpholine, 1-methylpiperazine, 1-(2-hydroxyethyl)piperazine, isonipecotamide, 4-hydroxypiperidine, 4-[3-(4-piperidyl)propyl]-1-piperidineethanol} gave a range of di- and trispirocyclic ammonium salts in satisfactory yields (22-62%). Presumably, the electrostatic and repulsion forces play an important role in their formation. The structure in soln. and the protonation...
-
Wstępny plan badań węzła z mimośrodem dodatnim w kratownicy z kształtowników o przekrojach poprzecznych otwartych. -(Autorka otrzymała wyróżnienie za tą publikację)
PublicationW celu określenia wpływu mimośrodowego przecinania się prętów w kratownicy z kształtowników giętych na zimno, o przekrojach poprzecznych otwartych na nośność i stateczność węzłów dźwigarów kratowych, opracowano model badawczy oraz przeprowadzono wstępną analizę numeryczną przedmiotowego węzła, w programie Marc Mentat. Uzyskane wyniki wskazują na potrzebę uzupełnienia obciążenia o parę sił poziomych w modelu badawczym.
-
Impacts in case of triple unilaterally constrained system
PublicationThe this paper focus on the behaviour of a “rigid” body biting into another “rigid” body, with some nonzero relative velocity. In the presently considered case, the introduced collision appears between a selected element of a multibody structure and its reference body being interpreted as the motionless ground. Instead of the classic case, described in a number of dissertations, where a single impacting contact is considered, three...
-
Sepulchral plate of Thomas Tympfius in St. Mary's Church in Gdańsk
Open Research DataThe data set concerns epigraphy. It refers to the sepulchral plate placed in St. Mary’s Church in Gdańsk which is dedicated to Thomas Tympfius, a minter who, together with his brother Andrew, rented several mints in the Kingdom of Poland, and gave his name to the timpf - the silver zloty released by the Tympfius mint. Unfortunately, as a result of...
-
Modelling of planar movement dynamics of upper limb
PublicationThe original model describing planar movement dynamics of upper limb is presented. The upper limb is modelled as two-joints system loaded by external forces and internal forces of striated skeletal muscles. A behaviour of each muscle is modelled as a system composed of serially linked rheologic fragments that have different mechanical properties. These muscle models allow us to simulate a behaviour of short fusiform muscle (3DOF...
-
The influence of screw configuration and screw speed of co-rotating twin screw extruder on the properties of products obtained by thermomechanical reclaiming of ground tire rubber
PublicationThe results of our investigations on the process of continuous thermomechanical reclaiming of ground tire rubber (GTR) carried out using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear forces. The influence of screw configuration and screw speed on breaking of chemical crosslink bonds contained in ground tire...
-
Galerkin Finite Element Process for Entropy Production and Thermal Evaluation of Third-Grade Fluid Flow: A Thermal Case Study
Publication: A fluid’s moving class improves its heat transmission capability, as well as its rigidity, owing to multivariate molecule suspension. In this way, nanofluids are superior to common fluids. In this study, we evaluated the features of ease and heat transfer. Furthermore, we investigated permeable media, heat source, variable heat conductivity, and warm irradiation results. A mathematical technique known as the Galerkin finite element...
-
Analyses of Shear Angle in Orthogonal Cutting of Pine Wood
PublicationThe determination of energy effects for wood machining processes, such as cutting power and cutting forces, is very useful in designing of manufacture process of wooden products. A more accurate prediction of cutting forces requires a correct determination of the shear angle value, which can be determined using various models. In this article, shear angle values for an orthogonal linear cutting process of pine wood are determined. The...
-
Tensile test results of fused filamend fabricated polylactyde and polylactyde with carbon fiber filler
Open Research DataThe Dataset contains the results of the mechanical behaviour of dog-bone shaped specimens. The specimens were additively manufactured with the fused filament fabrication (FFF) method. They used two different materials polylactide (PURE PLA) and polylactide with carbon fibre filler (PLA+CF). The specimens were segregated into three groups - unsterilized,...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublicationNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Stability of roof trusses stiffened by corrugated sheets
PublicationThe present parametric study is devoted to the stability analysis of a set of trusses stiffened by decking of corrugated steel sheets. For different parameters of corrugated sheets the critical loading of the roof is calculated. In the parametrical analysis the threshold bracing condition of the roof is obtained. Then the geometrically non-linear analysis of trusses braced by corrugated sheets was conducted. As a results of non-linear...
-
Wpływ współczynnika promienia walca i stosunku grubości warstw na odkształ- cenie warstwy twardej. The influence of radius of rolls coefficient and re-lations of thickness layers at the deformation of hard layers of bimetalic plate
PublicationW pracy przedstawiono analizę numeryczną walcowania blachy platerowanej 18 G2A i 0H18N10T. Wytwarzanie blach dwuwarstwowych jest procesem trudnym do rozwiązania na drodze teoretycznej. Do analizy procesu wykorzystano program Forge 2 oparty na teorii elementów skończonych. Artykuł przedstawia wpływ wartości współczynnika promienia walcaH/R i stosunku grubości warstw HT/HM na charakter rozkładu odkształceń blachy dwuwarstwowej.
-
Oferta kształcenia a wymogi współczesnego rynku pracy
PublicationWspółcześnie zmianom ulegają struktury gospodarek oraz sposoby gospodarowania poszczególnymi zasobami na rynkach. Wpływ na to mają nowoczesne technologie, procesy globalizacji i integracji. Obserwowane dynamiczne zmiany wymuszają włączenie się w proces unowocześniania różnych uczestników rynku. Jednym z nich są instytucje zajmujące się szeroko rozumianym kształceniem, które przygotowują zasoby pracy do wejścia na rynek pracy. Celem...
-
Experimental investigations on concrete beams reinforced with CFRP lamellas
PublicationPaper presents experimental investigation made on two concrete beams reinforced with internal Carbon Fibre Reinforced Polymer (CFRP) lamellas (i.e. strips, bands). The reinforcement geometrical arrangement was similar as in normal concrete beams reinforced with steel bars and stirrups. The beams were destroyed by the shear forces, as intended. Obtained load-carrying capacities were lower as expected: below 40% of a calculated value....
-
Pressure pulsations in turbine blade seal clearance
PublicationThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type, while the numerical results were obtained by means of CFD Fluent Code. The performed experimental research and numerical calculations prove that in a shroud clearance the pressure pulsates and the effects of...
-
Numerical modelling of asymetric double-layer Al-Cu plate rolling process
PublicationNiekorzystnym zjawiskiem towarzyszącym procesom walcowania płaskich wyrobów bimetalowych jest krzywizna pasma na wyjściu z kotliny walcowniczej wynikająca z nierównomierności odkształcenia warstw bimetalowej blachy. Możliwość szybkiego i łatwego przeciwdziałania temu zjawisku daje wprowadzenie asymetrii prędkości bądź średnic walców roboczych. W przedstawionym artykule zaprezentowano badania komputerowe procesu walcowania blach...
-
Load function walking pedestrian on the footbridge.
PublicationModern foot bridges are more and more sensitive to variable load created by moving pedestrians. These are several reasons for that. Quickly growing up road infrastructure forces us to build foot bridges just to reconnect one piece of land, separated now by the new road or railway. These bridges are lightweight because the only live load acting on them comes from pedestrians.The paper focuses on the definition of human induces dynamic...
-
Fuel systems of high power stationary engine
PublicationThe use of alternative fuels and, in the future, synthetic fuels has forced changes in the design of fuel supply systems in internal combustion engines. When operating a stationary engine at constant load, the possibility of using lean fuel mixtures appears. The selection of a precise operating mixture ignition system requires changes in traditional fuel systems. The article presents the current designs of fuel supply systems and...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-002)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-Con)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-004)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-006)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Mechanics of mesh implanted into abdominal wall under repetitive load. Experimental and numerical study
PublicationThere are a number of papers discussing medical and mechanical aspects of ventral hernia management. Despite intensive work on the problem understanding, recurrences of the sickness still happen too often. For that reason new aspects of the problem must be considered. In this paper, a change in the abdominal implant’s stiffness is discussed, which is caused by cyclic loading. Such loading influence abdominal implant e.g. while...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublicationPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Acoustic heating produced in the thermoviscous flow of a bingham plastic
PublicationThis study is devoted to the instantaneous acoustic heating of a Bingham plastic. The model of the Bingham plastic's viscous stress tensor includes the yield stress along with the shear viscosity, which differentiates a Bingham plastic from a viscous Newtonian fluid. A special linear combination of the conservation equations in differential form makes it possible to reduce all acoustic terms in the linear part of of the final equation...
-
Localized impedance measurements of AA2024 and AA2024-T3 performed by means of AFM in contact mode
PublicationPurpose: The purpose of this paper is to present the results of an atomic force microscopy (AFM) based approach to local impedance spectroscopy (LIS) measurement performed on AA2024 and AA2024-T3 aluminium alloys. Design/methodology/approach: AFM-LIS measurements were performed ex-situ without the electrolyte environment, so in fact the electrical not electrochemical impedance was obtained. Findings: Relative local impedance values...
-
Influence of compaction effectiveness on interlayer bonding of asphalt layers
PublicationThe paper presents the results of research on the interlayer bonding of asphalt layers compacted in the laboratory and in the field. To measure the interlayer bonding at a temperature of 20°C the Leutner test apparatus was used and load was applied at a rate of 50 mm/minute. Three types of interlayer interfaces were tested: no tack coat and tack coats made of two types of the pure bitumen emulsions. Four compaction techniques were...
-
THE IDENTIFICATION OF TOXIC COMPOUND EMISSION SENSITIVITY AS A DIAGNOSTIC PARAMETER DURING DYNAMIC PROCESSES OF THE MARINE ENGINE
PublicationChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure,...
-
Technical diagnostics and monitoring of traction current collectors
PublicationNew evaluation methods of the technical condition of rolling stock current collectors are proposed in this paper. The method of automatic measurement of the pantograph static force characteristic, realized when the vehicle runs through the test section of the track with especially prepared overhead line height distribution, has been practically implemented by the Polish Railways. The method of testing the slipper spring suspension...
-
Acoustic streaming caused by some types of aperiodic sound. Buildup of acoustic streaming
PublicationThe analysis of streaming caused by aperiodic sound of different types (switched on at transducer sound or sound determined by initial conditions) is undertaken. The analysis bases on analytical governing equation for streaming Eulerian velocity, which is a result of decomposition of the hydrodynamic equations into acoustic and non-acoustic parts. Its driving force (of acoustic nature) represents a sum of two terms; one is the...
-
Acoustic heating produced in the thermoviscous flow of a Bingham plastic
PublicationThis study is devoted to the instantaneous acoustic heating of a Bingham plastic. The model of the Bingham plastic's viscous stress tensor includes the yield stress along with the shear viscosity, which differentiates a Bingham plastic from a viscous Newtonian fluid. A special linear combination of the conservation equations in differential form makes it possible to reduce all acoustic terms in the linear part of of the final equation...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublicationThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Improvements and new functionalities of UNRES server for coarse-grained modeling of protein structure, dynamics, and interactions
PublicationIn this paper we report the improvements and extensions of the UNRES server (https://unres-server.chem.ug.edu.pl) for physics-based simulations with the coarse-grained UNRES model of polypeptide chains. The improvements include the replacement of the old code with the recently optimized one and adding the recent scale-consistent variant of the UNRES force field, which performs better in the modeling of proteins with the β and the...
-
Application of Shape Memory Alloys in Pipeline Couplings for Shipbuilding
PublicationThe aim of the study is to analyse shape memory alloy (SMA) pipeline joints in limited space applications for all kinds of ships. Generally, the space available in various areas on ships is strictly limited and service works usually meet many obstacles. If we consider a pipeline, the flange joints always require a larger free space around the pipe than the pipe alone. A simultaneous problem can occur with the propeller shaft line...
-
Use of Bi-Temporal ALS Point Clouds for Tree Removal Detection on Private Property in Racibórz, Poland
PublicationTrees growing on private property have become an essential part of urban green policies. In many places, restrictions are imposed on tree removal on private property. However, monitoring compliance of these regulations appears difficult due to a lack of reference data and public administration capacity. We assessed the impact of the temporary suspension of mandatory permits on tree removal, which was in force in 2017 in Poland,...
-
Numerical investigations of discrete crack propagation in Montevideo splitting test using cohesive elements and real concrete micro-structure
PublicationThe paper is aimed at accurately predicting the discrete fracture process in concrete specimens under complex stress states in two dimensional (2D) simulations. Plain concrete specimens subjected to Montevideo splitting test (MVD) were used for consideration due to non-negligible shear stresses impact in this type of test. In order to reflect the heterogeneous nature of the concrete, the meso-structure of the samples was included...
-
Numerical and experimental study on effect of boundary conditions during testing of stiffened plates subjected to compressive loads
PublicationThis study analyses the effect of boundary conditions during testing on the structural behaviour stiffened plates with different thicknesses subjected to compressive loads. The goal of the compressive tests is to analyse the ultimate strength of a stiffened plate. During the test, relevant physical quantities are measured and investigated. The supporting structure's behaviour is investigated by analysing the force-displacements...
-
Optimisation and field assessment of poroelastic wearing course bond quality
PublicationCompared to typical asphalt mixtures, poroelastic mixtures are characterised by high porosity and high flexibility, which are desirable for traffic noise reduction. However, the same properties increase the risk of debonding from the lower layer, which is a significant source of premature damage. The study investigates which of the factors – tack coat agent, type and texture of the lower layer – have the greatest impact on interlayer...
-
Open Innovation Competence for a Future-Proof Workforce: A Comparative Study from Four European Universities
PublicationDigital transformation is a key driving force of open innovation to capture and transfer knowledge inside and outside of a company’s bounds. New challenges in organizing multiple knowledge flows imply the need for increased competences related to this paradigm of future employees. In this article, we organize and aggregate the competencies required for open innovation collaboration and develop a competence profile that organizes...
-
Influence of Two-Stage Anodization on Properties of the Oxide Coatings on the Ti–13Nb–13Zr Alloy
PublicationThe increasing demand for titanium and its alloys used for implants results in need of such innovative surface treatment that may jointly increase corrosion resistance and biocompatibility, and demonstrate antibacterial protection at no cytotoxicity. The purpose of this research was to characterize the effect of two-stage anodization, performed for 30 min in phosphoric acid, at the presence of hydrofluoric acid in the second stage....
-
Miasta na prawach powiatu z rozwiniętym przemysłem jako lokalne ośrodki rozwoju na obszarach peryferyjnych polskich regionów
PublicationMost of the growth factors is situated in big cities, especially in metropolitan areas. Questions arise: 1) Whether and what development factors are in the peripheral areas of voivodeships (i.e. outside the functional areas of their capitals)? 2) Can the industry be the driving force of the development of these areas? These questions are related to the discussion on the reindustrialisation of the European Union and the role of...
-
Influence of external walls' thermal capacitance on indoor thermal comfort
PublicationThe doctoral thesis presents the results of numerical investigations on the influence of walls’ thermal capacitance on indoor thermal comfort. A proper set of thermal parameters of a building structure can considerably limit the heating / cooling demand, and passively increase the indoor thermal comfort. However the effect of building thermal capacitance on indoor conditions is complex and not always beneficial. Among a great number...
-
Rozdział mocy w układzie napędowym robota podwodnego - porównanie algorytmów alokacji naporów
PublicationPraca dotyczy syntezy systemu automatycznego sterowania robotem podwodnym w zakresie problemu rozdziału mocy w wielopędnikowym układzie napędowym. Do alokacji naporów zastosowano metody optymalizacji z ograniczeniami, pozwalające na wyznaczanie wektora naporów na podstawie wektora sił uogólnionych. Rozważono i porównano dwie metody rozdziału mocy dla robota realizującego ruch poziomy płaski o trzech stopniach swobody, rozpatrując...
-
Badania eksperymentalne słupów CFST z betonem zwykłym i ekspansywnym
PublicationPraca przedstawia badania eksperymentalne ponad 40 słupów CFST. Analizie poddano wyniki siły niszczącej słupy w aspekcie grubości stalowego płaszcza, smukłości słupa, rodzaju betonu wypełniającego stalową rurę (zwykły i ekspansywny) i jego wytrzymałości a także sposobu obciążania słupa (przez rdzeń lub przez cały przekrój). Sprawdzono efektywność słupów CFST z użyciem betonu ekspansywnego i zwykłego rozumianą jako stosunek nośności...
-
Konkursy studenckie jako narzędzie w określaniu potencjału rewitalizacyjnego miejskich terenów zdegradowanych.
PublicationZgodnie z zasadami prowadzenia działań rewitalizacyjnych określonych w ustawie o rewitalizacji obowiązującej od 9 października 2015 r. oraz horyzontalnych wytycznych w zakresie rewitalizacji w programach operacyjnych na lata 2014-2020 faza przygotowawcza procesu rewitalizacji powinna zawierać wielopłaszczyznowe analizy zakończone wnioskami aplikacyjnymi ujętymi w gminnych programach rewitalizacji obszarów zurbanizowanych. Artykuł...