Filtry
wszystkich: 1693
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: materials properties
-
Optical photoluminescent, and electroluminescent properties of organic solids
PublikacjaThis chapter discusses optical, photoluminescence and electroluminescence properties of organic materials. First, the spectral features of individual molecules and molecular solid states are analysed. Next, the excitonic processes in organic materials are discussed. The chapter reviews experimental methods leading to the determination of basic excitonic parameters. Finally, the electroluminescence phenomena in organic materials...
-
Novel luminescent calixarene-based lanthanide materials: From synthesis and characterization to the selective detection of Fe3+
PublikacjaCalix[n]arene-based coordination networks are an emerging class of materials with intriguing properties resulted from the presence of the cavity-like structure of the macrocycle and metallic nodes. In this work, four novel luminescent materials based on calix[4]arene-carboxylate and lanthanides (Eu3þ and Tb3þ) were prepared by two synthetic approaches, solvothermal (CDA-Eu-ST) and slow diffusion (CDA-Eu-RT, CDA-Tb-RT, CTA-Tb-complex)...
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublikacjaThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
Challenges and opportunities related to the use of sewage sludge ash in cement-based building materials – A review
PublikacjaDue to the increasingly demanding legal regulations, regarding both sewage sludge (SS) and solid residues obtained during its thermal utilization processes, new solutions to limit their negative impact on the environment are sought. One approach that eliminates the risk of sewage sludge ash (SSA) is its use in cement building materials. The article contains a detailed literature review regarding the use of SSA in mortars and concretes,...
-
Laboratory Determination of Burger's Model Parameters for Visco-elastic Analysis of Road Pavement Materials
PublikacjaBurger's Model is one of those models that describes performance of asphalt mixtures. Its parameters can be used in road construction analysis based on visco-elastic properties in wide variety of temperatures using dedicated programs (e.g. Veroad) or in Finite Element Method (FEM). Parameters of Burger's Model can be used for example in prediction of low temperature cracking in low winter temperatures or permanent deformation...
-
Recent advances on magnetic carbon-related materials in advanced oxidation processes of emerging pollutants degradation
PublikacjaRecently, carbon-related materials have been proposed to improve the charge separation of the photogenerated carriers in the semiconductor matrices’ and surface properties. Carbon-related materials may act as co-catalysts, enhancing the pollutants adsorption on the surface, improving the charge carriers separation and photocatalyst stability and providing more active centres for photocatalytic reactions. This review summarizes...
-
Modeling of wood frame structures with different insulation materials under damaging dynamic loading
PublikacjaWood frame buildings are very popular in regions that are exposed to different dynamic excitations, such as damaging earthquakes. Their seismic resistance is really important in order to prevent structural damages and human losses. This paper presents the results of advanced numerical investigation carried out using the FEM. Based on the models of wall panels, the numerical model of real structure of the wood frame building has...
-
Selection of material for X-ray tomography analysis and DEM simulations: comparison between granular materials of biological and non-biological origins
PublikacjaPhysical properties and X-ray tomography images of five different granular materials: glass bead, glass grit, short grain white rice, sorghum and clay granules (Seramis) are investigated to select the most promising materials for numerical simulations and time-lapse X-ray tomography imaging. The examined materials represent granular materials of non-biological origin (glass bead, glass grit and Seramis) and granular plant materials...
-
Polyurethanes Crosslinked with Poly(vinyl alcohol) as a Slowly-Degradable and Hydrophilic Materials of Potential Use in Regenerative Medicine
PublikacjaNovel, slowly-degradable and hydrophilic materials with proper mechanical properties and surface characteristics are in great demand within the biomedical field. In this paper, the design, synthesis, and characterization of polyurethanes (PUR) crosslinked with poly(vinyl alcohol) (PVA) as a new proposition for regenerative medicine is described. PVA-crosslinked PURs were synthesized by a two-step polymerization performed in a solvent...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Nonlinear Viscoelastic Properties of Polyurethane Nanocomposites
PublikacjaIn recent years, the nonlinear viscoelastic behaviors of elastomeric nanocomposites have been examined, especially for a wide range of rubbery composite (including natural rubber) materials. This chapter describes the influence of fillers and nanofillers on the nonlinear viscoelastic properties of elastomeric polyurethane systems. These filled elastomers (similar to the classic natural rubber reinforced elastomers), also exhibit...
-
A novel analytical approach in the assessment of unprocessed Kaffir lime peel and pulp as potential raw materials for cosmetic applications
PublikacjaVolatile fraction of fruits is a rich source of bioactive and aroma compounds, which can be used in the cosmetics industry after meeting relevant criteria. This is particularly evident in citrus fruits, especially in Citrus hystrix, in which the headspace consists mainly of terpenes. Due to the insufficient sensitivity of analytical methods, essential oils are used in investigations in contrast to fresh fruits. Therefore, a novel...
-
Petrophysical analyses of rock construction materials from the Roman rural settlement in Podšilo bay on Rab island (NE Adriatic, Croatia)
PublikacjaThis article presents the results of petrophysical analyses of limestones and sandstones used for the construction of the wall structures of a Roman rural settlement located in Podšilo Bay on Rab Island (Croatia). An on-site analysis of the walls indicated the use of different lithotypes, which is an uncommon case in the area. So far, no petrophysical properties of the applied materials have been tested, and their provenance...
-
Composite Materials Based on Polymer-Derived SiCN Ceramic and Disordered Hard Carbons as Anodes for Lithium-Ion Batteries
PublikacjaNew composite materials based on polymer-derived SiCN ceramics and hard carbons were studied in view of its application as anodes for lithium-ion batteries. Two kinds of composites were prepared by pyrolysis of the preceramic polysilazane (HTT1800, Clariant) at 1000 °C in Ar atmosphere mixed with hard carbons derived from potato starch (HC_PS) or with a hard carbon precursor, namely potato starch (PS), denoted as HTT/HC_PS and...
-
The external walls of a passive building: A classification anddescription of their thermal and optical properties
PublikacjaThis paper attempts a new classification of insulating materials from the perspective of their utility in thepro-ecological passive construction industry. The main criterion is the conductivity of thermal and solarenergy. Based on their ability to conduct or block fluxes of thermal and solar energy, six types of insulatingwalls are proposed. On the basis of this criterion there are traditional dividing walls (typical walls, wallinsulating...
-
Band engineering of BiOBr based materials for photocatalytic wastewater treatment via advanced oxidation processes (AOPs) – A review
PublikacjaSemiconductor based photocatalysts have been an efficient technology for water and wastewater remediation, addressing the concepts of green chemistry and sustainable development. Owing to narrow and suitable band structure, BiOBr is a promising candidate for efficient wastewater treatment via photocatalysis. Enhancement of photocatalytic properties can be obtained by various techniques like doping, element rich strategy, facet...
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublikacjaThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
Structure and thermoelectric properties of nickel-doped copper selenide synthesised in a hydrogen atmosphere
PublikacjaNickel-doped copper selenide—Cu2-xNixSe (x = 0; 0.01; 0.02; 0.03)—materials with high thermoelectric properties were synthesised through reduction of reagents in hydrogen. The impact of the nickel content on both the microstructure and thermoelectric properties was examined. The nickel-doped samples’ microstructure differed significantly from pristine copper selenide. Besides Cu2Se, copper precipitations were present in the materials....
-
Nanoconfined Ionic Liquids. Properties and analytical applications
PublikacjaThe synergistic combination of ionic liquids (ILs) and solid‐like matrices involves a powerful coupling towards the development of new sustainable analytical methodologies. Here we survey the literature regarding such ionic liquid‐based hybrid materials, including a database on relevant physicochemical properties of ionic liquids confined in a solid network. Furthermore, this chapter presents the strategies implemented to combine...
-
Release of Encapsulated Bioactive Compounds from Active Packaging/Coating Materials and Its Modeling: A Systematic Review
PublikacjaThe issue of achieving controlled or targeted release of bioactive compounds with specific functional properties is a complex task that requires addressing several factors, including the type of bioactive, the nature of the delivery system, and the environmental conditions during transportation and storage. This paper deals with extensive reporting for the identification of original articles using Scopus and Google Scholar based...
-
Influence of Surface-Modified Montmorillonite Clays on the Properties of Elastomeric Thin Layer Nanocomposites
PublikacjaIn recent years, polyurethane nanocomposites have attracted more attention due to the massive demand for materials with increasingly exceptional mechanical, optical, electrical, and thermal properties. As nanofillers have a high surface area, the interaction between the nanofiller and the polymer matrix is an essential issue for these materials. The main aim of this study is to validate the impact of the montmorillonite nanofiller...
-
Eco-Friendly Electromagnetic Interference Shielding Materials from Flexible Reduced Graphene Oxide Filled Polycaprolactone/Polyaniline Nanocomposites
PublikacjaHybrid nanocomposites have the unique ability of enhancing material properties due to the existing synergistic effect of the fillers. In this study, the authors report such an eco-friendly hybrid nanocomposite comprising of polyaniline and reduced graphene oxide in polycaprolactone. The conducting polyaniline improved the processability of polycaprolactone, and the final composites were prepared by incorporating graphene oxide...
-
The long-term properties of mineral-cement-emulsion mixtures
PublikacjaThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Cu-HKUST-1 and Hydroxyapatite–The Interface of Two Worlds toward the Design of Functional Materials Dedicated to Bone Tissue Regeneration
PublikacjaA novel composite based on biocompatible hydroxyapatite (HA) nanoparticles and Cu-HKUST-1 (Cu-HKUST-1@HA) has been prepared following a layer-by-layer strategy. Cu-HKUST-1 was carefully selected from a group of four Cu-based metal−organic frameworks as the material with the most promising antimicrobial activity. The formation of a colloidal Cu- HKUST-1 layer on HA nanoparticles was confirmed by various techniques, e.g., infrared...
-
MXenes Antibacterial Properties and Applications: A Review and Perspective
PublikacjaThe mutations of bacteria due to the excessive use of antibiotics, and generation of antibiotic-resistant bacteria have made the development of new antibacterial compounds a necessity. MXenes have emerged as biocompatible transition metal carbide structures with extensive biomedical applications. This is related to the MXenes’ unique combination of properties, including multifarious elemental compositions, 2D-layered structure,...
-
Structural and spectroscopic investigation of new luminescent hybrid materials based on calix[4]arene-tetracarboxylate and Ln 3+ ions (Ln = Gd, Tb or Eu)
PublikacjaLanthanide-calixarene hybrid materials are of particular interest due to the combination of the interesting properties of the ligand cavity-like structure and the luminescent features of lanthanides. The aim of this study was to synthesize and investigate the photophysical properties of Eu3+, Tb3+ and Gd3+ hybrids based on calix[4]arene-tetracarboxylate. The preparation of two structurally different...
-
Thermal and mechanical properties of polyurethanes modified with L-ascorbic acid
PublikacjaIn this study we report the thermal and mechanical properties of polyurethanes modified with ascorbic acid (AA). Ascorbic acid was used as a modifier at concentration of 1 or 2 mass%. The antioxidative properties of AA may improve the biocompatibility of the obtained materials, which were designed for biomedical applications. In this paper we describe characterization of obtained unmodified and ascorbic acid modified polyurethanes...
-
Facile synthesis and characterization of graphene and N-doped graphene by CVD method from liquid precursors for promising electrode materials
PublikacjaIn this study, high-quality and few-layered graphene was synthesized using the chemical vapor deposition (CVD) method from liquid sources. Two different liquid carbon sources, pyridine, and benzene, were used and deposited on nickel foam under heat conditions using a bubbler in a quartz tube. X-ray diffraction (XRD) and Raman analysis confirmed the crystalline properties of graphene and N-doped graphene, demonstrating the high...
-
Thermal Instability of Choline Chloride-Based Deep Eutectic Solvents and Its Influence on Their Toxicity─Important Limitations of DESs as Sustainable Materials
PublikacjaDeep eutectic solvents (DESs) have become a hot topic in many branches of science due to their remarkable properties. They have been studied in a wide variety of applications. In particular, choline chloride (ChCl)-based DESs are one of the most commonly used representatives of these fluids. Nevertheless, in order to apply DESs in some fields, it is essential to guarantee their stability, reusability, and biocompatibility. In this...
-
Mechanical Properties of Human Stomach Tissue
PublikacjaThe dataset entitled Determination of mechanical properties of human stomach tissues subjected to uniaxial stretching contains: the length of the sample as a function of the corresponding load (tensile force) and the initial values of the average width and average thickness of the sample. All tests were conducted in a self-developed tensile test machine: PG TissueTester. The dataset allows the coefficients of various models of...
-
Morphology and the physical and thermal properties of thermoplastic polyurethane reinforced with thermally reduced graphene oxide
PublikacjaIn this study, thermally reduced graphene oxide (TRG)-containing polyurethane nanocomposites were obtained by the extrusion method. The content of TRG incorporated into polyurethane elastomer systems equaled 0.5, 1.0, 2.0 and 3.0 wt%. The morphology, static and dynamic mechanical properties, and thermal stability of the modified materials were investigated. The application of TRG resulted in a visible increase in material stiffness...
-
An Influence of Factors of Flow Condition, Particle and Material Properties on Slurry Erosion Resistance
PublikacjaThe degradation of materials due to slurry erosion is the serious problem which occurs in the power industries. The paper presents actual knowledge about an influence of individual factors connected with flow conditions, particles and material properties on the slurry erosion resistance. Among the factors connected with operating conditions, an influence of impact angle, and velocity of impact, particle concertation and liquid...
-
Environmental Degradation of Engineering Materials & Materials Engineering and Technologies
Publikacja -
Comparison of Cu1.3Mn1.7O4 spinels doped with Ni or Fe and synthesized via wet chemistry and solid-state reaction methods, designed as potential coating materials for metallic interconnects
PublikacjaThe influence of the method applied to synthesize Cu-Mn-O spinel was evaluated. The methods selected for the investigation were EDTA gel processes and solid-state reaction synthesis. From the obtained powders, sinters were prepared and assessed in terms of their properties as potential coating materials. Additionally, the influence of Ni and Fe dopants was evaluated. The results show that the EDTA gel processes method seems to...
-
Influence of Rock Dust Additives as Fine Aggregate Replacement on Properties of Cement Composites—A Review
PublikacjaConcrete production consumes enormous amounts of fossil fuels, raw materials, and is energy intensive. Therefore, scientific research is being conducted worldwide regarding the possibility of using by-products in the production of concrete. The objective is not only to identify substitutes for cement clinker, but also to identify materials that can be used as aggregate in mortar and concrete productions. Among the potential alternative...
-
Chemical properties of bismuth telluride – carbon composites.
Dane BadawczeCarbon nanotubes and amorphous carbon have been introduced into bismuth telluride matrix (in 0.15 and 0.30 wt % ratio) in order to investigate influence of carbon on composite’s thermoelectric properties. Composites with well-dispersed additives have been obtained by sonication and ball-milling. Chemical composition of materials was confirmed by XPS...
-
Problems with modelling the strength properties of sailing vessels rigging ropes
PublikacjaThis article presents the basic parameters of soft ropes: natural fibre ropes, soft wire ropes and synthetic fibre ropes used for running rigging. There are only several materials still used for the production of natural fibre ropes, including cotton, jute, hemp, sisal and manila hemp. The most commonly used soft wire ropes are twisted pair ropes; for smaller diameters there is a 6x19M - FC rope and for larger diameters – 6x37M...
-
Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ on structural, electrical, and electrochemical properties for potential oxygen electrode of intermediate temperature solid oxide cells
PublikacjaThis work presents the results of a comprehensive study on the impact of the A-site non-stoichiometry of SrxTi0.3Fe0.7O3-δ (x = 0.90, 0.95, 1.00, 1.05) ceramics on their physicochemical properties. The materials were fabricated by the conventional solid-state reaction method and their structure was determined by X-ray diffractometry, X-ray photoelectron spectroscopy and electron microscopy. Their sintering and thermal expansion...
-
Raman Spectroscopy for Investigation of Sol-Gel Materials and Ceramic Materials.
PublikacjaPrzedstawiono rezultaty prac nad zastosowanie spektroskopii ramanowskiej do badania polimerów hybrydowych wytwarzanych metodą zol-żel oraz ceramik ferroelektrycznych. Wykonano pomiary dla próbek objętościowych i struktur cienkowarstwowych. Zademonstrowano możliwośc monitorowania procesu syntezy w czasie rzeczywistym.
-
Cavitation Erosion Resistance Influence of Material Properties
PublikacjaThe cavitation erosion is the phenomena that causes degradation of fluid flow machinery components due to repetitive implosion of cavitation bubbles adjacent to the solid surface. Cavitation erosion is a complex phenomenon, which includes not only hydrodynamic factors of liquid, but also properties of erodible material e.g. microstructure, hardness or Young modulus. In order to reduce the negative impact of erosion on machine components,...
-
Green thermoplastic poly(ether-urethane)s – synthesis, chemical structure and selected properties investigation
PublikacjaThis work aimed to characterize the effect of the monomers chemical structure on the selected properties of the green thermoplastic poly(ether-urethane)s. During synthesis two types of polyether biopolyols, 4,4′-diphenylmethane diisocyanate and bio-based 1,3-propanediol were employed. Materials were synthesized with the use of two step method and two different prepolymers, which were mixed together in equimolar quantities. Obtained...
-
Properties of LiMnBO3 glasses and nanostructured glass-ceramics
PublikacjaPolycrystalline LiMnBO3 is a promising cathode material for Li-ion batteries. In this work, we investigated the thermal, structural and electrical properties of glassy and nanocrystallized materials having the same chemical composition. The original glass was obtained via a standard melt-quenching method. SEM and 7Li solid-state NMR indicate that it contains a mixture of two distinct glassy phases. The results suggest that the...
-
Effect of Polymerization Statistics on the Electronic Properties of Copolymers for Organic Photovoltaics
PublikacjaStatistical block copolymers, composed of donor (D) and acceptor (A) blocks, are a novel type of material for organic photovoltaics (OPVs) devices. In particular a new series of polymers based on PBTZT-stat-BDTT-8, recently developed by Merck, offers high solubility in different solvents, and a high power conversion efficiency (PCE) in different device architectures. Although it is known that the electronic properties of these...
-
GTR/NBR/Silica Composites Performance Properties as a Function of Curing System: Sulfur versus Peroxides
PublikacjaIn this work, conventional sulfur and two types of organic peroxides (dicumyl peroxide (DCP) and di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB)) curing systems were used to investigate the possibility for tailoring of the performance properties of GTR/NBR blends reinforced with a variable content of highly dispersive silica (0–30 phr). The curing characteristics, static mechanical and acoustical properties, swelling behavior,...
-
The mechanical properties and bactericidal degradation effectiveness of tannic acid-based thin films for wound care
PublikacjaThe surface area is the most important aspect when considering the interactions between a material and the surrounding environment. Chitosan (CTS) and tannic acid (TA) were previously successfully tested by us to obtain thin films to serve as wound dressings or food packaging materials. However, surface properties as well as the antimicrobial activity of the material were not considered. They are important if the material is likely...
-
Structure and Stability Characterization of Natural Lake Pigments Made from Plant Extracts and Their Potential Application in Polymer Composites for Packaging Materials
PublikacjaNatural dyes were extracted from various plant sources and converted into lake pigments based on aluminum and tin. Three different plants (weld, Persian berries, and Brazilwood) were chosen as representative sources of natural dyes. High-performance liquid chromatography (HPLC) and triple-quadrupole mass spectrometry (QqQ MS) were used to identify dyestuffs in the raw extracts. The natural dyes and lake pigments were further characterized...
-
Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder
PublikacjaInvestigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry),...
-
Electrical properties of organic and perovskite systems used in solar cells
PublikacjaNowadays, a great progress in the areas of molecular and hybrid photovoltaics is observed. The devices based on organic and perovskite materials are getting attention mostly due to their low cost production process. However, their efficiency and stability are still lower than for inorganic materials which make them less popular. Therefore, a detailed understanding of the device physics is fundamental for organic and perovskite...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublikacjaThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
Thermal and Mechanical Properties of Microporous Polyurethanes Modified with Reduced Graphene Oxide
PublikacjaMicroporous polyurethanes (MPU) were modified by adding 0.25%–1.25 wt% of reduced graphene oxide (RGO). The materials were prepared without solvent via in situ polymerization. From a technological point of view, it is very important to obtain functional materials by using reacting compounds only. The thermal characteristics of obtained MPU were investigated using TGA, DSC, and DMA techniques. In comparison to nonmodified microporous...
-
Thorium and Uranium in the Rock Raw Materials Used For the Production of Building Materials
Publikacja -
Auxetic foams
PublikacjaThis paper presents a method of producing auxetic polyurethane foams (PUFs) and their unique properties. The experience was based on a synthesis of traditional flexible polyurethane foam and thermal conversion to auxetic foam. The foam specimens were transformed from conventional Poisson's ratio to auxetic (negative Poisson's ratio) [1]. Basic research was performed to determine the mechanical properties and cell structure. Auxetic...
-
Imaging of ferroelectric properties of sinter by means of Piezoresponse Force Microscopy
Dane BadawczeFerroelectricity is a property of certain materials [1], characterized by a spontaneous electrical polarization that can be reversed by applying an external electric field. Ferroelectric properties can be used to make capacitors with adjustable capacity. The permeability of ferroelectrics is not only regulated, but usually also very high, especially...
-
Underwater Processing of Materials
PublikacjaEditorial do SI
-
Morphology and properties of recycled polyethylene/ground tyre rubber/thermoplastic poly(ester-urethane) blends
PublikacjaThe growing amount of plastics waste produced every year resulted in development of mechanical and chemical recycling methods of polymers and their blends or composites. From the environmental point of view, the possibility of plastics waste reusing and recycling is desirable. In this study three polymer blends were obtained with using recycled polyethylene (RPE), ground tyre rubber (GTR) and thermoplastic poly(ester-urethane)...
-
Chemical modifications of graphene and their influence on properties of polyurethane composites: a review
PublikacjaPolyurethane composites are materials of great interest nowadays due to their wide range of available forms and applications in industry. Controlling and achieving unique properties via matrix modifications and addition of various specific nanofillers seems be one of the key elements to success. The purpose of this work is to briefly present some examples of graphene nanoderivatives, their syntheses, properties and influence on...
-
Valorization of bio-based polyols synthesized via biomass liquefaction
Dane BadawczeAs the properties of polyols have a huge impact on the properties of manufactured polyurethanes, this study aims to determine the influence of polyethylene glycols with different molecular masses on the course of the biomass liquefaction process and bio-polyol properties. The obtained polyols were characterized by rheological studies. To confirm the...
-
Influence of Water-Induced Degradation of Polytetrafluoroethylene (PTFE)-Coated Woven Fabrics Mechanical Properties
PublikacjaThe impact of water-induced degradation on the mechanical properties of the chosen two PTFE-coated, glass threads woven fabrics is investigated in this paper. The paper begins with a survey of literature concerning the investigation and determination of coated woven fabric properties. The authors carried out the uniaxial tensile tests with an application of flat and curved grips to establish the proper values of the ultimate tensile...
-
Corrosion Properties of Dissimilar AA6082/AA6060 Friction Stir Welded Butt Joints in Different NaCl Concentrations
PublikacjaA solid-state friction stir welding method which is increasingly used in the marine and shipbuilding industry, has been developed to produce welds with high mechanical properties. In seawater, the oxide layer of aluminium is attacked by Cl− ions resulting in its disruption and formation of pitting corrosion. It is particularly important to determine the electrochemical properties of the produced welds and to evaluate the efect...
-
Structure and properties comparison of poly(ether-urethane)s based on nonpetrochemical and petrochemical polyols obtained by solvent free two-step method
PublikacjaThe application of thermoplastic polyurethanes (TPU) is becoming more and more extensive, and the decreasing of used petrochemical monomers and reduction of energy for the polymerization and processing processes is getting increasingly important. In this paper, we confirmed the positive influence of high bio-based monomers contents (by replacing petrochemical polyol and glycol by bio-based counterparts) on processing and properties...
-
Effect of high loading of titanium dioxide particles on the morphology and selected properties of natural rubber-based composites
PublikacjaThe aim of this work was to prepare and characterize the natural rubber vulcanizates contained different amounts of titanium dioxide particles. At first rubber mixture was prepared using a laboratory two-roll mill and then samples were vulcanized in a hydraulic press. The formulation of rubber mixture and rubber-processing technique is based on our earlier investigations. Materials were obtained at the different titanium dioxide...
-
Thermal, electrical, and magnetic properties of Fe2O3–PbO–SiO2 glass prepared by traditional melt-quenching and twin roller fast-cooling methods
PublikacjaIn this study, Fe–Pb–Si oxide glasses containing between 12.5 and 17.5 mol% Fe2O3 were prepared using two different methods comprising traditional melt-quenching and twin roller fast-cooling techniques. The topography and structure of the materials obtained were characterized by X-ray powder diffraction and scanning electron microscopy. All of the materials were found to be amorphous. The topography of most of the glasses comprised...
-
Katarzyna Merkel dr hab.
OsobyOver the past 15 years, my work has mainly been related to the study of liquid crystal compounds with a diverse structure (discotic, dendrimeric, banana, bimedogenic, uniaxial and biaxial nematics and smectics) as well as polymeric materials (biopolymers, nano-composites) and biological materials. My work concerned mainly the issues of organization, observation of orientation effects, studying the dynamics of molecular processes...
-
Biomass-Derived Nitrogen Functionalized Carbon Nanodots and Their Anti-Biofouling Properties
PublikacjaThe prevalence of the antibiotic resistant bacteria remains a global issue. Cheap, sustainable and multifunctional antibacterial membranes are at the forefront of filtrating materials capable of treating multiple flow streams, such as water cleansing treatments. Carbon nanomaterials are particularly interesting objects shown to enhance antibacterial properties of composite materials. In this article, amino-functionalized, photoluminescent...
-
Obtaining and Characterization of the PLA/Chitosan Foams with Antimicrobial Properties Achieved by the Emulsification Combined with the Dissolution of Chitosan by CO2 Saturation
PublikacjaA new method of obtaining functional foam material has been proposed. The materials were created by mixing the poly lactic acid (PLA) solution in chloroform, chitosan (CS) dissolved in water saturated with CO2 and polyethylene glycol (PEG), and freeze-dried for removal of the solvents. The composite foams were characterized for their structural (SEM, FT-IR, density, porosity), thermal (DSC), functional (hardness, elasticity, swelling...
-
Obtaining and Characterization of the PLA/Chitosan Foams with Antimicrobial Properties Achieved by the Emulsification Combined with the Dissolution of Chitosan by CO2 Saturation
PublikacjaA new method of obtaining functional foam material has been proposed. The materials were created by mixing the poly lactic acid (PLA) solution in chloroform, chitosan (CS) dissolved in water saturated with CO2 and polyethylene glycol (PEG), and freeze-dried for removal of the solvents. The composite foams were characterized for their structural (SEM, FT-IR, density, porosity), thermal (DSC), functional (hardness, elasticity, swelling...
-
Palm Oil Fuel Ash-Based Eco-Efficient Concrete: A Critical Review of the Short-Term Properties
PublikacjaThe huge demand for concrete is predicted to upsurge due to rapid construction developments. Environmental worries regarding the large amounts of carbon dioxide emanations from cement production have resulted in new ideas to develop supplemental cementing materials, aiming to decrease the cement volume required for making concrete. Palm-oil-fuel-ash (POFA) is an industrial byproduct derived from palm oil waste’s incineration in...
-
Dielektryki-en WFTIMS
Kursy OnlineDielectric materials - properties, applications, structure.
-
Effects of Basalt and Carbon Fillers on Fire Hazard, Thermal, and Mechanical Properties of EPDM Rubber Composites
PublikacjaDue to growing restrictions on the use of halogenated flame retardant compounds, there is great research interest in the development of fillers that do not emit toxic compounds during thermal decomposition. Polymeric composite materials with reduced flammability are increasingly in demand. Here, we demonstrate that unmodified graphene and carbon nanotubes as well as basalt fibers or flakes can act as effective flame retardants...
-
Polyurethane Glycerolysate as a Modifier of the Properties of Natural Rubber Mixtures and Vulcanizates
PublikacjaChemical recycling of polyurethanes can be realized in several different ways, but the most important methods are glycolysis and glycerolysis. Both methods permit recovery of polyols (when the process is realized with the mass excess of depolymerizing agent) or substitutes of polyols, which contain urethane moieties in the main chains and terminate mainly in hydroxyl groups (when the process is realized with the mass excess of...
-
Improvement of microstructure and mechanical properties of high dense sic ceramics manufactured by high-speed hot pressing
PublikacjaNon-oxide ceramics possess high physical-mechanical properties, corrosion and radiation resistance, which can be used as a protective materials for radioactive wastes disposal. The aim of the present study was the manufacturing of high density SiC ceramics with advanced physical and mechanical parameters. The high performance on the properties of produced ceramics was determined by the dense and monolithic structure. The densified...
-
Physicochemical studies (Raman) of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains Raman spectroscopy studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...
-
Carbonized Metal-Organic Frameworks-based strucutres with aluminium, phosphorus and nitrogen
Dane BadawczeThe dataset includes Raman spectra of carbonized Metal-Organic Frameworks (MOF) [acquired on Renishaw] and electrochemical properties of the materials [acquired on EC Lab], which includes techniques such as Linear Sweep Voltammetry (LCV), Electrochemical Impedance Spectroscopy (EIS), Taffel slope and Chronopotentiometry (CP).
-
Preparation and characterization of porous scaffolds from chitosan-collagen-gelatin composite
PublikacjaNovel porous scaffolds composed of chitosan, collagen and gelatin were prepared and characterized. For preparing scaffolds gelatin and collagen isolated from fish skins with various physicochemical properties were used. In order to reduce preparation solubility glutaraldehyde in the amount of 1%, w/w relative to the total biopolymers weight in solution was used. All obtained biomaterials showed a homogeneous porosity. Protein polymer...
-
Physicochemical Properties and Application of Silica-Doped Biochar Composites as Efficient Sorbents of Copper from Tap Water
PublikacjaThis article concerns research on new sorption materials based on silica-doped activated carbon. A two-stage synthesis involved pyrolysis of plant material impregnated in a water glass solution , followed by hydrothermal activation of the pyrolysate in KOH solution. The resulting composite can be used as a sorbent in drinking water filters. The proposed method of synthesis enables the design of materials with a surface area...
-
Comparison of anti-plane surface waves in strain-gradient materials and materials with surface stresses
PublikacjaHere we discuss the similarities and differences in anti-plane surface wave propagation in an elastic half-space within the framework of the theories of Gurtin–Murdoch surface elasticity and Toupin–Mindlin strain-gradient elasticity. The qualitative behaviour of the dispersion curves and the decay of the obtained solutions are quite similar. On the other hand, we show that the solutions relating to the surface elasticity model...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublikacjaMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
PROCESSING, MECHANICAL AND THERMAL PROPERTIES OF RECYCLED LOW-DENSITY POLYETHYLENE STREAMS
PublikacjaThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for the potential methods of their utilization. Nevertheless, for the efficient application of recycled materials it is crucial to analyze their performance. Therefore, in presented paper we investigated the processing (melt flow index),...
-
Praseodymium Orthoniobate and Praseodymium Substituted Lanthanum Orthoniobate: Electrical and Structural Properties
PublikacjaIn this paper, the structural properties and the electrical conductivity of La1−xPrxNbO4+δ (x = 0.00, 0.05, 0.1, 0.15, 0.2, 0.3) and PrNbO4+δ are presented and discussed. All synthesized samples crystallized in a monoclinic structure with similar thermal expansion coefficients. The phase transition temperature between the monoclinic and tetragonal structure increases with increasing praseodymium content from 500 ◦C for undoped...
-
Effect of bio-polyol molecular weight on the structure and properties of polyurethane-polyisocyanurate (PUR-PIR) foams
PublikacjaThe increasing interest in polyurethane materials has raised the question of the environmental impact of these materials. For this reason, the scientists aim to find an extremely difficult balance between new material technologies and sustainable development. This work attempts to validate the possibility of replacing petrochemical polyols with previously synthesized bio-polyols and their impact on the structure and properties...
-
Influence of laser melting on surface layer properties of titanium alloy Ti6Al4V
PublikacjaIn time of rapid technology and medicine progress, implants are becoming more widely used in the human body, ranging from dental implants, stabilizing plates, screws, orthopaedic prostheses. For example, there are many types of hip prostheses used for hip replacement as well as various types of materials used for these orthopaedic prostheses. Properties of titanium alloys used in hip prostheses combined with good strength properties,...
-
An investigation on wetting of porous materials
PublikacjaPośrednie metody oceny zdolności zwilŜania drobnych cząstek lub materiałów porowatych wymagają wyboru cieczy odniesienia, dla której kąt zwilŜania jest równy zeru. W badaniach własnych zastosowanometodę wzniesienia kapilarnego oraz metodę flotacji filmowej dla układów mikrokulki szklane-woda i mikrokulki szklane-dekan. Uzyskane dane dla cieczy odniesienia i dla cieczy badanej wprowadzano dozmodyfikowanego równania Washburn'a i...
-
Determination of molybdenum in biological materials
Publikacja -
Application of organic materials in electronics
PublikacjaRozwój urządzeń elektronicznych na bazie materiałów organicznych przestawia jedno z najbardziej spektakularnych osiągnięć nauki w XXI wieku. Do produkcji zostały wdrożone urządzenia zbudowane na cienkich warstwach organicznych, i poczynione zostały pierwsze kroki w kierunku rozwoju elektroniki molekularnej. Celem publikacji jest dostarczenie podstawowych informacji dotyczących urządzeń elektronicznych zbudowanych na bazie cienkich...
-
Conductivity and superconductivity in granular materials
PublikacjaMetale i nadprzewodniki granulaste są bardzo ciekawymi materiałami dzięki jednoczesnej obecności oddziaływań kulombowskich, tunelowania elektronów i par Coopera oraz różnych zjawisk związanych z nieuporządkowaniem. W pracy przedstawiono i porównano niektóre właściwości granulastych nisko- i wysokotemperaturowych nadprzewodników. Granulasty nadprzewodnik wysokotemperaturowy otrzymano metodą krystalizacji w fazie stałej szkła (Bi,Pb)-Sr-Ca-Cu-O....
-
Sampling selected solid materials
PublikacjaW pracy przedstawiono: ogólne zasady pobierania próbek gleby, osadów dennychi innych materiałów stałych; opis urządzeń do pobierania próbek materiałówstałych; techniki przygotowania pobranych próbek do analizy.
-
Modelling of engineering materials with microstructure
PublikacjaArtykuł omawia różne modele do opisu lokalizacji odkształceń w postaci rys i stref ścinania w materiałach budowlanych takich jak grunt i beton. Zastosowane modele mechaniki ośrodka ciągłego i modele dyskretne.
-
Mechanical and Corrosion Properties of Laser Surface-Treated Ti13Nb13Zr Alloy with MWCNTs Coatings
Publikacja: Titanium and its alloys is the main group of materials used in prosthetics and implantology. Despite their popularity and many advantages associated with their biocompatibility, these materials have a few significant disadvantages. These include low biologic activity—which reduces the growth of fibrous tissue and allows loosening of the prosthesis—the possibility of metallosis and related inflammation or other allergic reactions,...
-
Solubilization of keratins and functional properties of their isolates and hydrolysates
PublikacjaThe keratinous wastes of the textile industry and poultry slaughterhouses may be used as sources of soluble keratins or hydrolysates. This review presents methods for processing raw keratin-based materials into bioproducts with functional and bioactive properties suitable for biomedical, cosmetic, food, and agricultural applications. Soluble keratin can be obtained by thermal treatment in some organic solvents, reduction, or oxidation...
-
Mechanical Properties of Bio-Composites Based on Epoxy Resin and Nanocellulose Fibres
PublikacjaThe aim of our research was to investigate the effect of a small nanocellulose (NC) addition on an improvement of the mechanical properties of epoxy composites. A procedure of chemical extraction from pressed lignin was used to obtain nanocellulose fibers. The presence of nanoparticles in the cellulose pulp was confirmed by FTIR/ATR spectra as well as measurement of nanocellulose particle size using a Zetasizer analyzer. Epoxy...
-
Thermodynamics of solid phases containing rare earth oxides
PublikacjaRare earth elements (RE) are incorporated into a large variety of complex oxide phases to provide tailored mechanical, electrical, optical, and magnetic properties. Thermodynamics control phase stability, materials compatibility in use, corrosion, and transformation. This review presents, in one compilation, the thermodynamic properties of a large number of such materials and discusses systematic trends in energetics and the factors...
-
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublikacjaA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
-
The luminescence study of LiGa5(1−x)O8:5xCr3+ coumpounds
Dane BadawczeInfrared luminescent materials have evoked much attention from chemists and material scientists. Although substantial progress is made in materials design, the luminescent mechanism remains ambiguous in the complex structures, presenting major barriers to developing novel infrared luminescent materials. Herein, this study aims to deliberate a complete...
-
Fourier transform infrared spectroscopy (FTIR) of pre- PXBS (0 h) and PXBS during the crosslinking process (24 h–288 h)
Dane BadawczeThe goal of this research was developing biodegradable and biocompatibile xylitol-based copolymers with improved mechanical properties, and investigating the change in their thermal and chemical properties withprogress of the cross-linking process. Using a raw material of natural origin such as xylitol, a prepolymer wasobtained by esterification and...
-
The assessment of microbiological antimicrobial properties of PE film loaded with nanozinc filler
Dane BadawczeThe dataset contains the results of a single series of determinations of the antimicrobial properties against E. coli and S. aureus of polyethylene films containing the nanozinc filler.
-
Evaluation of Mechanical Properties of Two-Stage Concrete and Conventional Concrete Using Nondestructive Tests
PublikacjaDifferent types of concrete mixtures are used as building materials. The manufacturing process of two-stage concrete (TSC) differs from that of conventional concrete. This study investigated conventional mechanical properties derive empirical relations for estimation of the mechanical parameters of TSC and conventional concrete mixtures. TSC was used to prepare 216 specimens and conventional concrete was used to prepare 108 specimens...
-
Synthesis, Structure and Properties of Poly(ester-Urethane-Urea)s Synthesized Using Biobased Diamine
PublikacjaModern polymer science and technology is focused on the development of partial or fully green polymers. This focus is related to green chemistry trends, which propose using natural and renewable resources as monomers in the synthesis of polymers. In this study, biobased diamine was used as a chain extender of ester-urethane prepolymer. Obtained poly(ester-urethane-urea) contains 16 wt% of biobased diamine. There is mention of an...
-
Broadband dielectric spectroscopy studies of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains broadband dielectric spectroscopy studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different...
-
Topography studies of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains topography studies with scanning electron microscope of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material...
-
Electrochemical analyses of multiple times processed poly(lactic acid)-carbon black composites
Dane BadawczeThis dataset contains cyclic voltammetry studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...