Filtry
wszystkich: 959
-
Katalog
- Publikacje 859 wyników po odfiltrowaniu
- Osoby 10 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Projekty 2 wyników po odfiltrowaniu
- Laboratoria 1 wyników po odfiltrowaniu
- Kursy Online 24 wyników po odfiltrowaniu
- Wydarzenia 2 wyników po odfiltrowaniu
- Dane Badawcze 60 wyników po odfiltrowaniu
Wyniki wyszukiwania dla: GENEROWANIE RESIDUÓW
-
Evolution of post welded residual stress due multilayer circumferentialweld of tube.
PublikacjaOpisano sposób wykorzystania polowego efektu Barkhausena do pomiaru rozkładu naprężeń w spawanych rurach. Przedstawiono procedurę kalibracji oraz wyniki pomiaru naprężeń uzyskanych po stopniowym spawaniu rury.
-
Requirements for Residual Current Devices Intended for Electric Vehicle Charging Systems
PublikacjaThe properties of residual current devices have been presented from the point of view of their ability to detect a specific shape of the residual current waveform. Moreover, the standard requirements relating to residual current protection used in electric vehicle charging installations have been pointed out. The operating characteristics of the IC-CPD and RDC-DD protections, which are intended for charging electric vehicles in...
-
Detection, identification and determination of chiral pharmaceutical residues in wastewater: Problems and challenges
PublikacjaChiral pharmaceuticals (CPs) are widely used in different areas of human life, thus they are frequentlydetected in different ecosystems. However, before CPs reach the environment, wastewater is subjected todifferent treatment processes in order to remove them. Nevertheless, such processes may affect thechirality of CPs, thus it is very important to monitor CP levels during the wastewater treatment.This review addresses the present...
-
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublikacjaMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
Determination of Pesticide Residues in Honey using the GC×GC-TOFMS Technique
PublikacjaIn this study, a QuEChERS method and gas chromatography coupled with time-of-flight mass spectrometry (GCxGC-TOFMS) was developed for rapid extraction and simultaneous determination of 12 pesticide residues in honey. The GCxGC-TOFMS method was validated according to the SANCO guidance in terms of linearity, selectivity, reproducibility and recovery. Regarding the results, recovery rates ranged between 70-120% with relative standard...
-
Stabilization of Solid Residues Obtained During Sewage Sludge Thermal Treatment
PublikacjaCurrently wastewater treatment plants are still dealing with the problem of ecological management of sewage sludge. Nowadays, thermal utilization is considered the most eco-friendly way of processing excess sludge. However, during mentioned process, fractions of ashes and dusts are generated. Such wastes, especially dusts fraction, can be potentially harmful for the environment and wastes should be stabilized before further management....
-
Pesticide residues levels in honey from apiaries located of Northern Poland
PublikacjaConcentration levels of 30 pesticide residues were measured in honey samples collected from apiaries in northern part of Poland (Pomerania) using method based on the QuEChERS extraction followed by liquid chromatography-tandem mass spectrometry with electron spray ionization (LC-ESI-MS/MS). In 29% of the samples were found positive for at least some of the target compounds. Concentration of bifenthrin, fenpyroximate, methidathion,...
-
Novel Diazocrowns with Pyrrole Residue as Lead(II) Colorimetric Probes
PublikacjaNovel 18- and 23-membered diazomacrocycles were obtained with satisfactory yields by diazocoupling of aromatic diamines with pyrrole in reactions carried under high dilution conditions. X-ray structure of macrocycle bearing five carbon atoms linkage was determined and described. Compounds were characterized as chromogenic heavy metal ions receptors. Selective color and spectral response for lead(II) was found in acetonitrile and...
-
High-speed binary-to-residue converter with the reduced input layer
Publikacjaprzedstawiono architekturę szybkiego konwertera z systemu binarnego do systemu resztowego dla modułów 5-bitowych. Algorytm konwersji oparty jest na dodawaniu binarnym reszt potęg liczby 2 obliczonych modulo m i redukcji modulo m sumy dla poszczególnych modułów bazy systemu resztowego. Warstwa wejciowa konwertera jest redukowana poprzez wykorzystanie wspólnych elementów układu dla odpowiednio zestawionych par modułów.
-
High-speed residue-to-binary converter based on the Chinese RemainderTheorem.
PublikacjaPrzedstawiono szybki konwerter z systemu resztowego do systemu binarnego dla modułów 5-bitowych oparty o chińskie twierdzenie o resztach. Projekcje ortogonalne są generowane przy użyciu odwzorowania realizowanego przy zastosowaniu funkcji logicznych pięciu zmiennych. Wartość wyjściowa jest obliczana przy użyciu drzewaWallace'a z segmentacją wektorów wyjściowych i redukcją do 2M, M zakres liczbowy systemu oraz efektywny finalny...
-
Pipelined division of signed numbers with the use of residue arithmetic in FPGA
PublikacjaAn architecture of a pipelined signed residue divider for small number ranges is presented. The divider makes use of the multiplicative division algorithm where initially the reciprocal of the divisor is calculated and subsequently multiplied by the dividend. The divisor represented in the signed binary form is used to compute the approximated reciprocal in the residue form by the table look-up. In order to reduce the needed length...
-
Scaling of numbers in residue arithmetic with the flexible selection of scaling factor
PublikacjaA scaling technique of numbers in resudue arithmetic with the flexible selection of the scaling factor is presented. The required scaling factor can be selected from the set of moduli products of the Residue Number System (RNS) base. By permutation of moduli of the number system base it is possible to create many auxilliary Mixed-Radix Systems associated with the given RNS with respect to the base, but they have different sets...
-
An investigation on residual stress and fatigue life assessment of T-shape welded joints
PublikacjaThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
How acidic amino acid residues facilitate DNA target site selection
PublikacjaDespite the negative charge of the DNA backbone, acidic residues (Asp/Glu) commonly participate in the base readout, with a strong preference for cytosine. In fact, in the solved DNA/protein structures, cytosine is recognized almost exclusively by Asp/Glu through a direct hydrogen bond, while at the same time, adenine, regardless of its amino group, shows no propensity for Asp/Glu. Here, we analyzed the contribution of Asp/Glu...
-
Advanced numerical modelling for predicting residual compressive strength of corroded stiffened plates
PublikacjaAn advanced methodology for predicting the residual compressive strength of corroded stiffened plates is developed here using the non-linear finite element method. The non-uniform loss of a plate thickness is accounted for on a macro-scale. In contrast, mechanical properties are changed using the constitutive model to reflect the corrosion degradation impact on a micro-scale. Three different stiffened plate thicknesses are considered,...
-
Identification of residual force in static load tests on instrumented screw displacement piles
PublikacjaOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...
-
Influence of circuit breaker operation upon transformeros residual flux and inrush current
PublikacjaPrzedstawiono model i wyniki obliczeń prądu i strumienia magnetycznego w układzie zawierającym transformator trójfazowy i wyłącznik. Opracowano obwodowy model łącznika z łukiem elektrycznym. Model łuku zbudowano w oparciu o jego statyczną charakterystykę prądowo-napięciową z uwzględnieniem uproszczonej charakterystyki dynamicznej. Przeprowadzone symulacje wykazały, że wartość maksymalna prądu włączania transformatora zależy zarówno...
-
Novel calix[4]resorcinarenes with side azobenzo-15-crown-5 residues
PublikacjaZsyntezowano nowe kaliks[4]rezorcareny z dwoma lub czteroma resztami azobenzo-15-korony-5 w dowolnym pierścieniu. Związki te otrzymano w reakcji kondensacji rezorcynolu z odpowiednimi aldehydami (acetalami).
-
Menopause: a trigger for simultaneous development of ulcerative colitis in sigmoid neovagina and residual colorectum?
Publikacja -
Solution conformations of bradykinin antagonists modified with CαCα cyclized nonaromatic residues
Publikacja -
Numerical Analysis of Magnetic Core Properties Influence on Residual Current Device Behaviour
PublikacjaW artykule przedstawiono analizę wpływu kształtu prądu w uzwojeniu pierwotnym transformatora prądowego na pracę przekładnika różnicowo-prądowego. Przeprowadzono obliczenia symulacyjne dla wymuszenia o kształcie sinusoidy i sinusoidy wyprostowanej dla częstotliwości 50 Hz. Wzięto pod uwagę dwa typy charakterystyki magnesowania transformatora: dla materiału magnetycznie miękkiego i materiału o prostokątnej pętli histerezy. Analiza...
-
Residual Effects of Different Cropping Systems on Physicochemical Properties and the Activity of Phosphatases of Soil
Publikacja -
Numerical calculation of three-phase transformer's residual flux in ATP and PSpice programs.
PublikacjaW artykule przedstawiono analizę przebiegów prądu i strumienia magnetycznego podczas wyłączania transformatora energetycznego, wykonaną w celu określenia strumieni szczątkowych. Wykorzystano do tego celu modele obwodowe zbudowane w oparciu o programy symulacyjne ATP (Alternative Transients Program) i PSpice. Wyniki obliczeń okazały się bardzo zbliżone dla obu modeli. Przy ich wykorzystaniu obliczono strumienie szczątkowe w kolumnach...
-
Characterization of Mesorhizobium huakuii lipid A containing bothD-galacturonic acid and phosphate residues.
PublikacjaLipid A jest mieszaniną co najmniej 6 związków, różniących się stopniem fosforylacji i strukturą kwasów tłuszczowych przyłączonych do szkieletu polisacharydowego. Szkielet cukrowy zawiera beta(1'->6)połączone dwie cząsteczki 2,3-diamino-2,3-dideoksyglucosy (DAG)oraz aglikon kwas alfa-D-galaktouronowy.
-
Greenness assessment of analytical methods used for antibiotic residues determination in food samples
PublikacjaFood of animal origin plays an important role in ensuring a healthy and sustainable human diet. However, residues of pharmaceuticals, especially antibiotics, can be the cause of many health problems. To protect consumers and improve food quality, analytical methods used to determine contaminants should be simple, selective, and have high throughput and low detection limits. Recently, greenness metric tools have proven useful in...
-
Testing sensitivity of A-type residual current devices to earth fault currents with harmonics
PublikacjaIn many applications, modern current-using equipment utilizes power electronic converters to control the consumed power and to adjust the motor speed. Such equipment is used both in industrial and domestic installations. A characteristic feature of the converters is producing distorted earth fault currents, which contain a wide spectrum of harmonics, including high-order harmonics. Nowadays, protection against electric shock in...
-
New Trends in Sample Preparation Techniques for the Analysis of the Residues of Pharmaceuticals in Environmental Samples
PublikacjaPharmaceutical residues in the environment is a field of special interest due to the adverse effects to either human health or aquatic and soil environment. Pharmaceuticals have been already detected in underground, surface and wastewaters, soils, manure and sediments. The growing awareness of environmental pollution arising from human activity forces the need for their comprehensive determination. Environmental samples are complex...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublikacjaIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Determination of pesticide residues in fruits and vegetables using QuEChERS sample preparation method
PublikacjaThe intensive development of agriculture means that more and more toxic organic and inorganic compounds are entering the environment. Because of their widespread use, environmental stability, selective toxicity and bioaccumulative capability, pesticides belong to the most hazardous substances contaminating the environment. They are particularly dangerous in fruits and vegetables, because they are one of the reasons why people are...
-
Improving sensitivity of residual current transformers to high frequency earth fault currents
PublikacjaFor protection against electric shock in low voltage systems residual current devices are commonly used. However, their proper operation can be interfered when high frequency earth fault current occurs. Serious hazard of electrocution exists then. In order to detect such a current, it is necessary to modify parameters of residual current devices, especially the operating point of their current transformer. The authors proposed...
-
Quechers sample preparation method variants for analysis of pesticide residues in fruits and vegetables
PublikacjaThis article describes the comparison of different versions of an easy, rapid and low-cost sample preparation approach for the determination of pesticide residues in fruits and vegetables by concurrent use of gas and liquid chromatography coupled to MS or ECD for detection. The sample preparation approach is known as QuEChERS, which stands for quick, easy, cheap, effective, rugged and safe. It is a combination of liquid-liquid...
-
Fault loop impedance measurement in low voltage network with residual current devices
PublikacjaW sieciach i instalacjach niskiego napięcia z wyłącznikami różnicowoprądowymi pomiar impedancji pętli zwarciowej jest kłopotliwy. Prąd pomiarowy powoduje ich zbędne zadziałanie, co uniemożliwia prawidłowe wykonanie pomiaru. W artykule omówiono przyczyny zbędnego zadziałania wyłączników różnicowoprądowych podczas pomiaru impedancji pętli zwarciowej oraz warunki, w jakich ten pomiar można wykonać poprawnie.
-
Driver influence on tyre/road noise generated by vehicle in road traffic.Wpływ kierowcy na hałas generowany przez pojazd w ruchu drogowym.
PublikacjaW pracy omówiono wkływ stylu jazdy kierowcy oraz stanu technicznego wybranych zespołów pojazdu na jego hałas generowany w ruchu drogowym. Wpływ został przeanalizowany w aspekcie takich parametrów, jak: prędkość jazdy, obciążenie kół siłami wzdłużnumi i poprzecznymi, ciśnienie w ogumieniu, obciążenie pionowe kół, zbieżność i inne.
-
Strength and Compressibility of Ammonia-Soda Residue from the Solvay Sodium Plant
Publikacja -
Validation of the HS-GC-FID method for the determination of athanol residue in tablets
PublikacjaW pracy opisano proces walidacji metody oznaczania zawartości pozostałości etanolu w tabletkach. W pomiarach wykorzystano technikę HS-GC-FID. Wyznaczono następujące parametry walidacyjne:- selektywność- liniowość- poprawność- precyzję (powtarzalność i precyzję pośrednią)- granice wykrywalności i oznaczalności- zakres pomiarowy- niepewność
-
Validation of the HS-GC-FID method for the determination of ethanol residue in tablets
Publikacja -
Solvent residue determination in Uncaria Tomentosa Bark by HS-GC technique
PublikacjaPrzedstawiono wyniki oznaczeń pozostałości rozpuszczalników organicznych w preparacie uzyskanym z kory liany U. Tomentosa, wykorzystywanej do produkcji farmaceutyków i dodatków do żywności. 1,1,2-trichloroeten oraz dichlorometan są powszechnie stosowane do usunięcia z kory kilku grup alkaloidów o znanych właściwościach biologicznych, co umożliwia zbadanie pozostałych jej związków. Ilościowe oznaczanie tych rozpuszcalników jest...
-
Photolysis for the Removal and Transformation of Pesticide Residues During Food Processing: A State-of-the-Art Minireview
PublikacjaPesticide residues are of great significant issue that exerted adverse effects on humans. There is a need for effective and non-toxic decontamination of pesticide residues during food processing. In this minireview, the recent advances in the degradation of pesticide residues by photolysis have been firstly described during food processing. The mechanisms of pesticide residues destruction by photolysis were discussed accordingly....
-
Electrical safety in low-voltage DC microgrids with B-type residual current devices
PublikacjaResidual current devices (RCDs) are most popular devices used in low-voltage installations for protection against electric shock and fire. In cases of high risk of electric shock the application of RCDs is mandatory. Currently, the spread of local direct current (DC) microgrids is widely considered. This creates new challenges for protective systems, in particular those based on RCDs. The main purpose of the research is to test...
-
Tripping of F-type RCDs for sinusoidal residual current with superimposed smooth DC component
PublikacjaRecent trends in green energy development make that photovoltaics and electric vehicles are applied on an increasing scale. In both photovoltaic and electric vehicle charging installations, a significant value of DC component of the earth fault current may appear, which is a challenge, in particular, for commonly used residual current devices (RCDs). This paper presents results of the laboratory test on the operation of F-type...
-
Pyrolysis of Pruning Residues from Various Types of Orchards and Pretreatment for Energetic Use of Biochar
PublikacjaThe routine pruning and cutting of fruit trees provides a considerable amount of biowaste each year. This lignocellulosic biomass, mainly in the form of branches, trunks, rootstocks, and leaves, is a potential high-quality fuel, yet often is treated as waste. The results of a feasibility study on biochar production by pyrolysis of residues from orchard pruning were presented. Three types of biomass waste were selected as raw materials...
-
Stimulated by cyclodextrins high yield synthesis of azocrown analogues comprising pyrrole or imidazole residues
PublikacjaThe influence of cyclodextrins (CDs) on the formation of azocrown ethers comprising pyrrole, imidazole and substituted imidazole has been studied. Pyrrole, imidazole, 2-methyl-, 4-methyl- and 4-phenylimidazole were coupled with bisdiazonium salts derived from bis-1,5-(2-aminophenoxy)-3-oxapentane or bis-1,8-(2-aminophenoxy)-3,6-dioxaoctane to form macrocyclic compounds with two azo units. The syntheses were performed under standard...
-
Stimulated by cyclodextrins high yield synthesis of azocrown analogues comprising pyrrole or imidazole residues
PublikacjaBadano wpływ cyklodekstryn na reakcję syntezy aza-eterów zawierających w strukturze pirol lub imidazol. Stosowano alfa-, beta- i gamma-cyklodekstryny. Uzyskane wyniki analizowano pod kątem sposobu umieszczenia cząsteczki azolu we wnęce cyklodekstryny.
-
Protection Against Electric Shock Using Residual Current Devices in Circuits with Electronic Equipment
PublikacjaW artykule przedstawiono problematykę stosowania wyłączników różnicowoprądowych w obwodach z urządzeniami elektronicznymi, które powodują, że prąd różnicowy ma zmienną częstotliwość lub jest odkształcony. Wyniki badań wskazują, że częstotliwość obiegająca od znamionowej oraz zawartość wyższych harmonicznych w prądzie różnicowym niekorzystnie wpływa na skuteczność ochrony przeciwporażeniowej przy zastosowaniu wyłączników różnicowoprądowych....
-
Analytical Techniques for Determining Pharmaceutical Residues in Drinking Water – State of Art and Future Prospects
Publikacja -
Synthesis of analogues of anthraquinones linked to tuftsin or retro-tuftsin residues as potential topoisomerase inhibitors
PublikacjaZsyntetyzowano 10 nowych analogów antrachinonów z pochodnymi tuftsyny i retro-tuftsyny jako potencjalne inhibitory topoizomerazy. Substratem wyjściowym były zsyntetyzowane 1,4-, 1,5- i 1,8-bis(tosyloksy)-9,10-antrachinony oraz odpowiednio chronione pochodne tuftsyny i retro-tuftsyny, które otrzymano metodą mieszanych bezwodników z zastosowaniem chloromrówczanu izobutylu i NMM. Reakcje prowadzone były w acetonitrylu pod azotem w...
-
Complementary studies of residual stress distribution of repaired power plant steam turbine casing
PublikacjaRozkład i poziom naprężeń własnych w korpusach turbin badano za pomocą efektu Barkhausena oraz metodą nawiercania otworów. Badano również twardość. Korpusy były reperowane metodą zaspawania. Wykazano, iż zastosowana technologia nie wprowadza naprężeń o poziomie zagrażającym dalszej ekploatacji korpusu.
-
Determination of solvents residues in vegetable oils and pharmaceuticals by headspace analysis and capillary gas chromatography.
PublikacjaPrzedstawiono wyniki zastosowania techniki analizy fazy nadpowierzchniowej w połączeniu z kapilarną chromatografią gazową do oznaczania wybranych rozpuszczalników organicznych w próbkach olejów jadalnych i produktów farmaceutycznych. Oznaczane rozpuszczalniki to: benzen, toluen, heksan oraz chlorowcopochodne węglowodorów alifatycznych. Opracowaną procedurę poddano walidacji. Wyznaczono granicę wytrzymalności, oznaczalności, liniowość...
-
Influence of Surface Laser Treatment on Mechanical Properties and Residual Stresses of Titanium and its Alloys
PublikacjaSurface modification of the titanium and its alloys used in implantology with a long-pulse laser can change the surface topography, but it also leads to changes in the stress sign and magnitude in the resulting subsurface layer. The presented research was aimed at evaluating the state of stress after laser remelting with the Nd:YAG laser of pre-etched titanium alloys Ti6Al4V and Ti13Nb13Zr and pure titanium. The obtained surface...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublikacjaThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Immunity of residual current devices to the impulse leakage current in circuits with variable speed drives
PublikacjaThis paper concerns reliability of supply in variable speed drive circuits with residual current devices. During normal operation of these circuits high value of leakage current causes unwanted tripping of residual current devices. Immunity of residual current devices to the impulse leakage current should be evaluated. The system for testing of residual current devices and results of the test are presented
-
The Current State-of-the-Art in the Determination of Pharmaceutical Residues in Environmental Matrices Using Hyphenated Techniques
PublikacjaSeveral thousand tons of pharmaceuticals and their transformation products (metabolites and degradation products) are introduced into the environment each year. They affect both human health and the environment, therefore, analytical procedures enabling the determination of a wide range of pharmaceuticals at trace levelswithminimal effort, time, and energy are required. Nowadays, hyphenated techniques are commonly applied in pharmaceutical...
-
Application of Immunological Techniques (from Vaccination to FinalMeasurements) in Determination of Pharmaceutical Residues in Environmental Samples
PublikacjaWiele biologicznie aktywnych związków wytwarzanych przez człowieka trafia ostatecznie do środowiska. Ich los środowiskowy pozostaje nadal wyzwaniem dla analityków środowiskowych i osób odpowiedzialnych za szacowanie ryzyka. Artykuł przedstawia przegląd jednej z najszerszych i bezpośrednich metod analiz środowiskowych - immunoanalitykę - ze szczególnych uwzględnieniem jej zastosowania do oznaczania jakościowego i ilościowego pozostałości...
-
Discussion of Derivability of Local Residual Stress Level from Magnetic Stray Field Measurement
PublikacjaThe NDT procedure dubbed ‘metal magnetic memory’ method and the related ISO 24497 standard has found wide industrial acceptance in some countries, mainly in Russia and China. The method has been claimed by some researchers (Roskosz and Bieniek in NDT&E Int 45:55–62, 2012; Wilson et al. in Sens Actuators A 135:381–387, 2007) as having potential for quantitative determination of local residual stress state in engineering structures,...
-
Occurrence and seasonal variations of 25 pharmaceutical residues in wastewater and drinking water treatment plants
PublikacjaThousands of tons of pharmaceuticals are introduced into the aqueous environment due to their incomplete elimination during treatment process in wastewater treatment plants (WWTPs) and water treat- ment plants (WTPs). The presence of pharmacologically active compounds in the environment is of a great interest because of their potential to cause negative effects. Furthermore, drugs can undergo different pro- cesses leading to the...
-
Design of a complex multiplier based on the convolution with the use of the polynomial residue number system
Publikacjazaproponowano realizację mnożnika zespolonego opartego na algorytmie dekompozycyjnym skavantzosa i stouraitisa. mnożenie zespolone jest wykonywane jako splot 8-punktowy. przedstawiono przykład obliczeniowy i architekturę mnożnika dla małych liczb.
-
An improved high-speed residue-to-binary converter based on the chinese remainder theorem
Publikacjaw pracy zaprezentowano nowy szybki konwerter z systemu resztowego do systemu binarnego. Projekcje ortogonalne wyznaczane są przy użyciu funkcji logicznych pięciu zmiennych. Suma projekcji obliczana jest z zastosowaniem drzewa Wallace'a. Wektor sumy i wektor przeniesienia są dzielone na segmenty tak aby liczba reprezentowana łącznie przez obydwa segmenty o młodszych wagach nie przekraczała zakresu systemu resztowego,M. Bity segmentów...
-
On configuration of residue scaling process in pipelined radix-4 MQRNS FFT processor
PublikacjaResidue scaling is needed in pipelined FFT radix-4 processors based on the Modified Quadratic Residue Number System (MQRNS) at the output of each butterfly. Such processor uses serial connection of radix-4 butterflies. Each butterfly comprises n subunits, one for each modulus of the RNS base and outputs four complex residue numbers. In order to prevent the arithmetic overflow in the succesive stage, every number has to be scaled,...
-
On simplification of residue scaling process in pipelined Radix-4 MQRNS FFT processor
PublikacjaResidue scaling is needed in pipelined FFT radix-4 processors based on the Modified Quadratic Residue Number System (MQRNS) at the output of each butterfly. Such processor uses serial connection of radix-4 butterflies. Each butterfly comprises n subunits, one for each modulus of the RNS base and generates four complex residue numbers. In order to prevent arithmetic overflow intermediate results after each butterfly have to be...
-
FPGA realization of high-speed multi-stage FIR filter in residue arithmetic
PublikacjaW pracy przedstawiono implementację szybkiego wielostopniowego, kaskadowego filtru FIR w technologii FPGA. Zastosowanie arytmetyki resztowej pozwala na uzyskanie dużych częstotliwości próbkowania w zwiżaku z użyciem małych mnożników. Zalety wynikające z uzycia arytmetyki resztowej sa w pewnym stopniu ograniczne koniecznością wykonania skalowania przy kaskadowym połaczeniu filtrów FIR, tak aby uniknąć nadmiaru arytmetycznego. W...
-
Fpga implementation of the two-stage high-speed fir filter in residue arithmetic
Publikacjaw pracy przedstawiono implementację szybkiego, dwustopniowego kaskadowego filtru fir w technologii fpga z użyciem arytmetyki resztowej. zastosowanie arytmetyki resztowej pozwala na uzyskanie dużych częstotliwości potokowania w związku z użyciem małych mnożników. zalety arytmetyki resztowej są ograniczane w pewnym stopniu koniecznością wykonywania skalowania po pierwszym stopniu filtru celem uniknięcia nadmiaru arytmetycznego. w...
-
Piotr Konieczka prof. dr hab. inż.
Osoby -
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Application of the Finite Element Method for Modelling of the Spatial Distribution of Residual Stresses in Hybrid Surface Layers
Publikacja -
Residual Current Devices Operational Characteristics within the Frequency Range 50 Hz to 1000 Hz.
PublikacjaW artykule przedstawiono charakterystyki działania powszechnie stosowanych wyłączników różnicowoprądowych przy prądach różnicowych w zakresie częstotliwości 50÷1000 Hz. Częstotliwość wyższa niż 50 Hz wpływa niekorzystnie na prąd zadziałania wyłączników, a w skrajnych przypadkach mogą one w ogóle nie reagować na wolno narastający prąd różnicowy.
-
Elimination of the negative effect of earth fault current higher frequency on tripping of residual current devices
PublikacjaCzęstotliwość prądu różnicowego większa niż 50/60 Hz ma niekorzystny wpływ na wyzwalanie wyłączników różnicowoprądowych. Przy zwiększonej częstotliwości prądu różnicowego rzeczywisty prąd zadziałania wyłączników zwiększa się, a niektóre z nich w ogóle nie wyzwalają. W artykule omówiono główne przyczyny zwiększenia się prądu zadziałania wyłączników różnicowoprądowych oraz przedstawiono sposób eliminacji niekorzystnego wpływu zwiększonej...
-
Performance of Vector-valued Intensity Measures for Estimating Residual Drift of Steel MRFs with Viscous Dampers
PublikacjaViscous Dampers (VDs) are widely used as passive energy dissipation system for improving seismic performance levels especially in retrofitting of buildings. Residual Inter-story Drift Ratio (R-IDR) is another important factor that specifies the condition of building after earthquake. The values of R-IDR illustrates the possibility of retrofitting and repairing of a building. Therefore, this study aims to explore the vector-valued...
-
Advanced Scalar-valued Intensity Measures for Residual Drift Prediction of SMRFs with Fluid Viscous Dampers
PublikacjaMaximum Residual Inter-story Drift Ratio (RIDRmax) plays an important role to specify the state of a structure after severe earthquake and the possibility of repairing the structure. Therefore, it is necessary to predict the RIDRmax of Steel Moment-Resisting Frames (SMRFs) with high reliability by employing powerful Intensity Measures (IMs). This study investigates the efficiency and sufficiency of scalar-valued IMs for predicting...
-
RCDs Tripping in the Range from DC to AC 50 kHz for Slowly Rising Residual Current
PublikacjaThe wide use of power electronic converters means that in many low-voltage systems earth fault currents containing components from DC to AC of various frequencies have to be taken into account. Due to the tendency to increase the modulation frequency in converters, components of higher frequencies may be in the order of several tens of kilohertz. Therefore, it is very important to verify the behavior of devices for protection against...
-
Verification of safety in low-voltage power systems without nuisance tripping of residual current devices
PublikacjaLow-voltage power systems require initial and periodical verification to check the effectiveness of protection against electric shock. As a protection in case of fault, automatic disconnection of supply is most often used. To verify such a protection measure, the earth fault loop impedance or resistance is measured. This measurement is easy to perform in circuits without residual current devices. When residual current devices are...
-
The effect of PWM frequency on the effectiveness of protection against electric shock using residual current devices
PublikacjaW referacie przedstawiono analizę widmową odkształconego prądu ziemnozwarciowego z obwodu silnika o regulowanej prędkości obrotowej za pomocą przemiennika częstotliwości. Oszacowano wpływ tego odkształcenia na próg fibrylacji serca. Analizowano skuteczność ochrony przeciwporażeniowej wykorzystującej wyłączniki różnicowoprądowe przy różnych wartościach częstotliwości PWM przemiennika. Przedstawiono charakterystykę działania zaproponowanego...
-
The Dominant Influence of Plastic Deformation Induced Residual Stress on the Barkhausen Effect Signal in Martensitic Steels
PublikacjaThe paper presents the results of investigation of the influence of plastic deformation on the magnetic properties of martensitic steel (P91 grade). The properties of the hysteresis loops as well as of the Barkhausen effect (BE) signal are analysed for both tensile and compressive loading up to ε = 10% of plastic deformation. The choice of the steel and of the deformation range is unique, since for such combination one can expect...
-
A new method of fault loop resistance measurement in low voltage systems with residual current devices
PublikacjaThis paper presents a new method of fault loop resistance measurement in low voltage systems with residual current devices. The method enables measuring fault loop resistance without nuisance tripping of residual current devices, by application an unconventional waveform of measurement current. It is important for proper verification of the effectiveness of protection against electric shock.
-
Analytical procedures for quality control of pharmaceuticals in terms of residual solvents content: Challenges and recent developments
PublikacjaResidual solvents play an important role in the synthesis of drugs and in product formulations. In addition, they pose a serious problem, that is toxicity, as many of them exhibit toxic or environmentally hazardous properties. Therefore, constant monitoring of quality control is needed. In this study, we present an overview of regulatory and general methods described by various pharmacopoeias. Then, the most commonly used methodologies...
-
Derivatization of SWCNTs with cobalt phthalocyanine residues and applications in screen printed electrodes for electrochemical detection of thiocholine
PublikacjaJednościenne nanorurki węglowe (SWCNTs) sfunkcjonalizowane resztami ftalocyjaniny kobaltu zostały nałożone na sitodrukowane elektrody grafitowe (SPEs) i zastosowane do elektrochemicznego utleniania tiocholiny (TCh) w zakresie niskich potencjałów. Kowalencyjne przyłączenie ftalocyjaniny kobaltu do SWCNTs trwałym wiązanie sulfonamidowym zostało dowiedzione spektroskopią Ramana i UV-Vis i analizą termograwimetryczną połączoną z detekcją...
-
The effect of PWM frequency on the effectiveness of protection against electric shock using residual current devices
PublikacjaW artykule przedstawiono analizę widmową odkształconego prądu ziemnozwarciowego z obwodu silnika o regulowanej prędkości obrotowej za pomocą przemiennika częstotliwości. Oceniono skuteczność ochrony przeciwporażeniowej wykorzystującej wyłączniki różnicowoprądowe przy różnych wartościach częstotliwości PWM przemiennika. Przedstawiono charakterystykę działania proponowanego wyłącznika różnicowoprądowego.
-
Modification of the operating point of residual current transformers for high frequency earth fault currents detection
PublikacjaFor protection against electric shock in low voltage systems residual current devices are commonly used. However, their proper operation can be interfered when earth fault current with high frequency components occurs. Serious hazard of electrocution exists then. One of the most important element of residual current devices is a residual current transformer with iron core. Tripping characteristic of residual current devices strictly...
-
Evaluation of applicability of classic methods of a fault loop impedance measurement to circuits with residual current devices
PublikacjaMeasurement of fault loop impedance in low voltage grids and systems is in most cases performed to verify the effectiveness of protection against electric shock by automatic disconnection of supply. For the sake of measurement accuracy, it is advisable to perform it using large current. Unfortunately, in circuits with residual current devices which are very widely used nowadays, a large measurement current may trigger those devices...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublikacjaThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Janusz Górski prof. dr hab. inż.
Osoby -
FPGA realization of the high-speed residue-to-binary converter based on the Chinese Remainder Theorem
Publikacja...
-
Replica Exchange and Multicanonical Algorithms with the Coarse-Grained United-Residue (UNRES) Force Field
Publikacja -
Preparation and characterization of Langmuir-Blodgett films of 16-membered azobenzocrown ether with naphthalene residue
PublikacjaOtrzymano i charakteryzowano filmy Langmuira-Blodgett 16-członowej azobenzokorony z resztą naftalenową. Monowarstwy Langmuira były z sukcesem przenoszone na stałe substraty z utworzeniem filmów LB. Filmy osadzone na elektrodach z ITO zostały również użyte jako elektrody w woltametrii cyklicznej i uzyskano rezultaty wskazujące na to, że filmy te wykazują wyraźną odpowiedź na jony metali.
-
Production of Biogas from Distillation Residue as a Waste Material from the Distillery Industry in Poland
PublikacjaIn this paper, the possibility to obtain an alternative source of energy from methane fermentation, catalysed by biomass, has been discussed in detail. As a main substrate, the distillation residue from the distillery industry was taken in the case of mono-fermentation and its co-fermentation with sewage sludge. The results showed that higher biogas and methane production can be obtained in a mono-fermentation process. Fermentation...
-
Pipelined sceling of signed residue numbers with the mixed-radix conversion in the programmable gate array
PublikacjaIn this work a scaling technique of signed residue numbers is proposed. The method is based on conversion to the Mixed-Radix System (MRS) adapted for the FPGA implementation. The scaling factor is assumed to be a moduli product from the Residue Number System (RNS) base. Scaling is performed by scaling of terms of the mixed-radix expansion, generation of residue reprezentation of scaled terms, binary addition of these representations...
-
Radix-4 dft butterfly realization with the use of the modified quadratic residue number system
PublikacjaW pracy zaprezentowano projektowanie i realizację obliczenia motylkowego dft dla podstawy 4 z użyciem zespolonego systemu resztowego (CRNS) i zmodyfikowanego kwadratowego systemu resztowego (MQRNS). System MQRNS oprócz własności dekompozycyjnych pozwala na realizację mnożenia zespolonego przy zastosowaniu trzech mnożeń rzeczywistych. Przedstawiono konwertery wejściowy CRNS/MQRNS i wyjściowy MQRNS/CRNS, mnożenie zespolone w MQRNS,...
-
Radix-4 dft butterfly realization with the use of the modified quadratic residue number system
PublikacjaW pracy przedstawiono algorytm realizacji mnożenia zespolonego z użyciem zmodyfikowanego kwadratowego zmodyfikowanego systemu liczbowego (mqrns) oraz jego zastosowanie do wykonania obliczenia motylkowego dft dla podstawy 4. pokazano też wstępne rezultaty implementacji w układzie xilinx fpga.
-
FPGA realization of the high-speed residue-to-binary converter based on chinese remainder theorem
PublikacjaW pracy przedstawiono architekturę, realizację FPGA oraz symulację numeryczną na poziomie bitowym szybkiego konwertera z systemu resztowego do systemu binarnego dla modułów 5-bitowych opartego na chińskim twierdzeniu o resztach. Algorytm konwertera obejmuje obliczanie projekcji ortogonalnych poprzez odczyt pamięci oraz sumowanie modulo M realizowane dwustopniowo, pierwszy stopień oparty o sumatory CSA umożliwia redukcję do zakresu...
-
Sample preparation procedure for the determination of polycyclic aromatic hydrocarbons in petroleum vacuum residue and bitumen
PublikacjaThis paper describes a novel method of samplepreparation for the determination of trace concentrations ofpolycyclic aromatic hydrocarbons (PAHs) in high-boilingpetroleum products. Limits of quantitation of the investigatedPAHs in materials of this type range from tens ofnanograms per kilogram to <20 μg/kg. The studies revealedthat in order to separate most of interferences from theanalytes without a significant loss of PAHs, it...
-
Wpływ nawierzchni jezdni na hałas drogowy - część 2
PublikacjaW pracy przedstawiono mechanizmy generowania hałasu opon związane z drganiami mechanicznymi oraz z przepływami powietrza. Omówiono wpływ rzeźby bieżnika opony oraz tekstury nawierzchni na generowany hałas podczas toczenia się opony po nawierzchni jezdni.
-
Edytor polityk negocjacyjnych mobilnego dokumentu elektronicznego
PublikacjaW artykule opisano edytor polityk negozjacyjnych umożliwiający generowanie ich specyfikacji w postaci bardzo rozległych drzew na podstawie elementów składowych ofert oraz reguł polityk i ich wartościowanie. Przedstawiono również zarys problemu negocjacji miedzy dokumentem a agentem, ktory ma ten dokument obsługiwać. Drzewa generowane przez edytor mają posłużyć za zbiory uczące dla sieci neuronowej przyspieszającej proces negocjacji.
-
Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels
PublikacjaThis article deals with the dissimilar joining of two different grade Cr-Mo steel (2.25Cr-1Mo: P22 and modified 9Cr-1Mo: P91) for power plant application. The dissimilar butt-welded joint was produced for conventional V groove design by using the gas tungsten arc welding (GTAW) process with the application of an ERNiCrMo-3 Ni-based super alloy filler. A microstructure characterization was performed to measure the inhomogeneity...
-
Emissions and toxic units of solvent, monomer and additive residues released to gaseous phase from latex balloons
PublikacjaThis study describes the VOCs emissions from commercially available latex balloons. Nine compounds are determined to be emitted from 13 types of balloons of different colors and imprints in 30 and 60°C. The average values of total volatile organic compounds (TVOCs) emitted from studied samples ranged from 0.054 up to 7.18 μg∙g-1 and from 0.27 up to 36.13 μg∙g-1 for 30oC and 60oC, respectively. The dataset is treated with principal...
-
The application of single drop extraction technique for chromatographic determination of solvent residues in edible oils and pharmaceutical products
PublikacjaW pracy przedstawiono zalety i wady techniki ekstrakcji do pojedynczej kropli, będącą prostą i tanią alternatywą dla mikroekstrakcji do fazy stacjonarnej. Ponadto opisano dwie analityczne procedury do chromatograficznego oznaczania wybranych rozpuszczalników organicznych (heksanu, benzenu, toluenu oraz trichlorometanu, 1,1,1-trichloroetanu, tetrachlorometanu, trichloroetylenu, tetrachloroetenu)w olejach jadalnych i próbkach farmaceutycznych....
-
Validation of SPME-GC and HS-GC procedures for the determination of selected solvent residues in edible oil matrices
PublikacjaW pracy przedstawiono przebieg procesu walidacji, przeprowadzonej zgodnie ze wskazaniami ICH (International Conference on Harmonization), procedur wykorzystywanych do oznaczania pozostałości wybranych rozpuszczalników w olejach jadalnych i preparatach farmaceutycznych. W celu izolacji i wzbogacania analitów wykorzystano dwie bezrozpuszczalnikowe techniki ekstrakcyjne: ekstrakcję do fazy nadpowierzchniowej (HS) i mikroekstrakcję...
-
Environmental aspects of using gas chromatography for determination of pharmaceutical residues in samples characterized by different composition of the matrix
Publikacja -
Laboratory station for research of the innovative dry method of exhaust gas desulfurization for an engine powered with residual fuel
PublikacjaContemporary methods of exhaust gas desulfurization in marine engines are all expensive methods (4-5 million euro). This is, among other reasons, due to the limited market audience, but primarily due to the monop-olized position of manufacturers offering fabrication and assembly of this type of marine ship installations. Proposed as part of a research project financed by the Regional Fund for Environmental Protection and Maritime...
-
Levels of 13 multi-class pesticide residues in Polish honeys determined by LC-ESI-MS/MS
PublikacjaLevels of 13 pesticides in 40 honey samples form Poland are reported. A rapid and sensitive method was developed for the LC-ESI-MS/MS determination of multi-class pesticide residues in honey samples. Liquid-liquid extraction (LLE) on a diatomaceous earth support (requiring the use of small amounts of organic solvent), followed by chromatographic separation on a C18 column and gradient elution were employed. The method quantifies...
-
Fast-response optoelectronic detection of explosives’ residues from the nitroaromatic compounds detonation: field studies approach
PublikacjaWe are presenting an application of optoelectronic nitrogen dioxide (NO2) analyzer based on cavity enhanced absorption spectroscopy in the detection of traces of explosives after detonation. It has been shown that the analyzer using blue-violet laser is able to detect explosive residues after the detonation of various amounts of nitroaromatic compounds (75g-1kg) with higher efficiency than the HPLC soil sample testing equipment,...