Filters
total: 604
filtered: 580
-
Catalog
Chosen catalog filters
Search results for: phase investigations
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublicationThe paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 mikrometer respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling...
-
Structural properties of superconducting PrBa 2Cu 3O 7−δ single crystals
PublicationThe influence of high-temperature reduction/oxidation treatment on the structural properties of superconducting PrBa2Cu3O7−δ (PrBCO) single crystals was examined. The scanning electron microscopy (SEM) analysis has shown that even the short-lasting exposure to the oxygen-deficient atmosphere leads to creation of regular-shaped crystallites of PrBaO3 and BaCuO2 phases with the size of 0.5 ÷ 2.0 μm on the smooth and flat crystal...
-
The influence of humic substances in treated sewage on the quality of surface waters
PublicationAt present the evaluation of WWTP effectiveness is based upon organic matter and nutrients removal. Recently it was found out that sewage treatment leads to formation of resistant to biochemical degradation organic compounds, similar to humic acids. The humic acids formed during sewage treatment process play diversified functions when discharged to surface waters - for instance they can act as carriers of hydrophobic organic pollutants...
-
Rebuilding Bailey Bridge to Bridge With Bascule Span – A Case Study
PublicationThe structural analysis of a road foldable prefabricated steel Bailey- type bridge located over the Tuga River in Żelichowo, Poland is performed in this paper. Interesting and untypical bridge redevelopment performed made it possible to lift the middle foldable bridge span by approximately 4.0 m concerning the existing state. The paper begins with a survey of literature carried out on the investigations of foldable Bailey-type...
-
Speed Sensorless AC Drive with Inverter LC Filter and Fault Detection Using Load Torque Signal
PublicationThe industrial development in recent years has seen a major increase in the use of induction motors, whereby the cost has to be as low as possible and the lifetime as long as possible. To follow up this desire, investigations in this area have become very intense. For that reason, this paper presents a solution for driving an induction motor and simultaneous fault detection with no need for additional sensors. In order to achieve...
-
THE INFLUENCE OF GESTALT THEORY ON ERNST CASSIRER’S PHENOMENOLOGY OF SYMBOLIC FORMS
PublicationIn the opinion of many scholars the notion of symbolic pregnancy is one of the key concepts in Ernst Cassirer’s philosophy of symbolic forms. Without a proper under-standing of its conceptual frame Cassirer’s philosophy lacks a consistent foundation. The notion symbolic pregnancy offers the mechanism of distinction of symbolic forms. The newest investigations (also in unpublished or less known, neglected writings of the philosopher)...
-
Determination of authenticity of brand perfume using electronic nose prototypes
PublicationThe paper presents practical application of an electronic nose technique for fast and efficient discrimination between authentic and fake perfume samples. Two self-built electronic nose prototypes equipped with a set of semiconductor sensors were employed for that purpose. Additionally 10 volunteers took part in sensory analysis. The following perfumes and their fake counterparts were analysed: Dior – Fahrenheit, Eisenberg – J’ose,...
-
Corrosion behavior of concrete produced with diatomite and zeolite exposed to chlorides
PublicationChloride induced reinforcement corrosion is widely accepted to be the most frequent mechanism causing premature degradation of reinforced concrete structures. The electrochemical impedance of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sodium chloride was assessed. Chemical, physical and mineralogical properties of three concrete samples (20% diatomite, 20% zeolite, and a reference containing neither)...
-
Analysis of guided wave propagation in adhesive joints of steel rods
PublicationThe aim of the study is the elastic wave propagation in adhesive joints of metal rods that are one of the simplest kind of glue connections. They are consisted of two metal members and an adhesive layer joining two parts together. The analysis is directed to technical diagnostics of such type of connections. Longitudinal and transversal guided waves were excited in prepared joints. Signals of propagating waves were registered in...
-
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublicationThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
Doped Nanocrystalline Diamond Films as Reflective Layers for Fiber-Optic Sensors of Refractive Index of Liquids
PublicationThis paper reports the application of doped nanocrystalline diamond (NCD) films—nitrogen-doped NCD and boron-doped NCD—as reflective surfaces in an interferometric sensor of refractive index dedicated to the measurements of liquids. The sensor is constructed as a Fabry–Pérot interferometer, working in the reflective mode. The diamond films were deposited on silicon substrates by a microwave plasma enhanced chemical vapor deposition...
-
Investigations of Aerodynamics of Tesla Bladeless Microturbines
PublicationThe paper presents an analysis of a Tesla bladeless turbine for a co-generating micro-power plant of heat capacity 20 kW, whichoperates in an organic Rankine cycle with a low-boiling medium. Numerical calculations of flow in several Tesla turbine models areperformed for a range of design parameters. Results of investigations exhibit interesting features in the distribution of flowparameters within the turbine interdisk space. The...
-
COMPARISON OF INFINITE ELEMENT MODELS
PublicationThe main objective of this paper is to show the comparison of two models of infinite ab- sorbing layer with increasing damping in numerical investigations of elastic wave prop- agation in unbounded structures. This has been achieved by the Authors by a careful in- vestigation of two different engineering structures characterised by gradually increasing geometrical and mathematical description complexities. The analysis included...
-
Nitrogen conversion during treatment of various type of wastewater in multistage treatment wetlands
PublicationThe objective of this investigation was to recognize nitrogen speciation during wastewater treatment in three multistage TWs (MTWs), which are assuming more a most effective in nitrogen removal than single stage TWs. Carried out investigations and analysis enable for determination of conditions, relationships and processes responsible for nitrogen conversions in subsequent stages of MTWs. In treated wastewater and reject water...
-
Searching of the buried objects into the sea bottom by means of nonlinear acouctic methods
PublicationThe main goal of this paper is to introduce the methodology of preparing the area for investigations that will be carried out at the sea. As the first step there is recognition of the basic method both in the theory as well as experimental investigation. There were taken into account the nonlinear methods. These ones are very promising methods that have very interesting features, very convenient for examinations of the seabed structure....
-
Wpływ smarowności na działania układu tribologicznego (impact of lubricity on the tribological system action)
Publicationthe paper presents analysis and evaluation, based on tests results, of the impact of lubricity of the used lubricating oils (shell argina t 40) on the action of boundary layer of sulzer 6zl40/48 engines aboard the ''włocławek'' sea-going ship. for comparison purposes, the same oils were tested with the ceramizer four-stroke engine (all types of the vidar four-stroke engines) regeneration agent added. so understood boundary layer...
-
Interline power flow controller - properties and control strategy in dynamic states
PublicationHigh-power electronic converter topologies, in such forms as Unified Power Flow Controllers (UPFC), Static Compensators (STATCOM) and Interline Power Flow Controllers (IPFC), have been used to enhance and optimize the use of transmission facilities, under the concept of a flexible ac transmission system (FACTS). In Europe, the anticipated proliferation of distributed-generation (DG) in the near future, driven by governmental initiatives...
-
Microfluidic devices for photo-and spectroelectrochemical applications
PublicationThe review presents recent developments in electrochemical devices for photo- and spectroelectrochemical investigations, with the emphasis on miniaturization (i.e., nanointerdigitated complementary metal-oxide-semiconductor devices, micro- and nano-porous silicon membranes or microoptoelectromechanical systems), silica glass/microreactors (i.e., plasmonic, Raman spectroscopy or optical microcavities) or polymer-based devices (i.e.,...
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublicationThe mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete Element Methods....
-
The analytical design method of railway route’s main directions intersection area
PublicationThe paper presents a design method related to railway track sections situated in a bend. In the method advantage is taken of an analytical form of description by using appropriate mathematical formulae. This may becomeparticularly usefulwhen the investigations are based on the data obtained from mobile satellite measurements. In the paper attention is concentrated on an universal approach creating an opportunity to diversify the...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublicationIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Modelling of dielectric properties of BiNbO4-based microwave ceramics
PublicationIn the present paper results of the studies devoted to computer simulations of dielectric response of electroceramics in a frequency domain as well as analysis of the experimental data are given. As an object of investigations BiNbO4-based microwave ceramics was taken. Simulations of the hypothetical impedance response of the ceramic system were performed under assumption of the brick-layer model. A strategy for analysis and modelling...
-
On low-fidelity models for variable-fidelity simulation-driven design optimization of compact wideband antennas
PublicationThe paper addresses simulation-driven design optimization of compact antennas involving variable-fidelity electromagnetic (EM) simulation models. Comprehensive investigations are carried out concerning selection of the coarse model discretization density. The effects of the low-fidelity model setup on the reliability and computational complexity of the optimization process are determined using a benchmark set of three ultra-wideband...
-
THE METHOD OF ENERGY-EFFICIENCY INVESTIGATIONS OF THE NEWLY PRODUCED MARINE FUELS THROUGH AN APPLICATION OF THE LABORATORY DIESEL ENGINE
PublicationThe article deals with one of the scientific issue solved within frames of the research project financed by Voivodeship Fund for Environmental Protection and Water Management in Gdansk, namely, in particular, the method of energy investigations of the self-ignition engine in conditions of its supply with a non-standard (modified) marine fuel. The representative results of engine tests worked out on the especially built laboratory...
-
Use of radiography images and gray level co-occurrence matrix to investigate gravitational granular flow
PublicationThe paper presents analysis of granular gravitational flow based on radiography images processing. The investigations were conducted for silo model geometry with concentric/eccentric discharging modes. The continuous X-ray radiography scans of granular material distribution, acquired during flow, were obtained by means of an especially designed model silo with rectangular bin and different settings of hopper angles. Image processing...
-
Impact of Geometrical Imperfections on Estimation of Buckling and Limit Loads in a Silo Segment Using the Vibration Correlation Technique
PublicationThe paper examines effectiveness of the vibration correlation technique which allows determining the buckling or limit loads by means of measured natural frequencies of structures. A steel silo segment with a corrugated wall, stiffened with cold-formed channel section columns was analysed. The investigations included numerical analyses of: linear buckling, dynamic eigenvalue and geometrically static non-linear problems. Both perfect...
-
Novel inorganic xerogels doped with CaWO 4 :xDy: Synthesis, characterization and luminescence properties
PublicationA series of novel phosphors based on silica xerogel doped with CaWO4:xDy(III) with various concentration of dysprosium ion was synthesized over a temperature of 800 C. The thermal analysis, XRD measurement and spectroscopic investigations of these materials are presented in this study. Steady state luminescence, luminescence excitation spectra as well as emission spectra have been measured. Under the ultraviolet light, the prepared...
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublicationAbstract: The mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also on the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete...
-
Palladium versus Platinum: The Metal in the Catalytic Center of a Molecular Photocatalyst Determines the Mechanism of the Hydrogen Production with Visible Light
PublicationTo develop highly efficient molecular photocatalysts for visible light-driven hydrogen production, a thorough understanding of the photophysical and chemical processes in the photocatalyst is of vital importance. In this context, in situ X-ray absorption spectroscopic (XAS) investigations show that the nature of the catalytically active metal center in a (N^N)MCl2 (M=Pd or Pt) coordination sphere has a significant impact on the...
-
The influence of thermal conditions on V2O5 nanostructures prepared by sol-gel method
PublicationThis work presents the result of structure investigations ofV 2O5 nanorods grown from thin films and powders prepared by sol-gel method. To examine the best temperature of nanorods crystallization, thin films deposited by spin-coating method on quartz glass or silicon substrates and bulk xerogel powders were annealed at various temperatures ranging from 100∘C to 600∘C. The structure of the samples was characterized by X-ray diffraction...
-
A commercial gas boiler fitted with the ORC module as perspective solution for households
PublicationIn this paper the applicability of the commercial gas boiler (De Dietrich DTG X23N) coupled with the laboratory prototype micro ORC setup was experimentally studied. The main objective was to determine the working fluid capability to obtain required temperatures of vapour prior to the turbine, attainable heat rates and efficiencies of the whole system. The boiler thermal power was 25 kW. Tests were carried out with a single stage...
-
Evidence for solid state electrochemical degradation within a small molecule OLED
PublicationAcridone derivative have been synthesised and used as OLED (Organic Light Emitting Diode) emitters which were found to be electroactive. Electrochemical investigations showed a side reaction takes place inside an active layer which diminished the overall device efficiency. By using a dopant and host active layer architecture, the formation of the by product was removed. The by-product was identified as a σ-dimer formed inside an...
-
Influence of external walls' thermal capacitance on indoor thermal comfort
PublicationThe doctoral thesis presents the results of numerical investigations on the influence of walls’ thermal capacitance on indoor thermal comfort. A proper set of thermal parameters of a building structure can considerably limit the heating / cooling demand, and passively increase the indoor thermal comfort. However the effect of building thermal capacitance on indoor conditions is complex and not always beneficial. Among a great number...
-
Longitudinally magnetized left-handed cylindrical ferrite coupled line junction for nonreciprocal devices
PublicationThis paper presents investigations of longitudinally magnetized left-handed cylindrical ferrite coupled line junction for nonreciprocal devices. The proposed junction is formed as a quasi periodic arrangement of N unit cells. Each unit cell is realized as a cascade of short cylindrical ferrite coupled lines with reactance circuit composed of series capacitors and parallel inductors. The left-handed cylindrical junction with π/4...
-
Radiosensitization of DNA in presence of Pt(II)-based compounds
PublicationX-ray irradiation of plasmid DNA in presence of platinum (II)-based compounds was carried out in order to assess the radiosensitization capabilities of these drugs. In present investigations pBR322 plasmid DNA was used to monitor the effectiveness of chosen compounds in inducing strand breaks. Samples were incubated in the presence of potential radiosensitisers: platinum (II) bromide and cis-diamminedibromoplatinum (II). The results...
-
Power Electronics Building Blocks for implementing Smart MV/LV Distribution Transformers for Smart Grid
PublicationWith an observed increase in the involvement of active consumers in activities aimed at improving energy efficiency and increasing interest in producing energy from renewable sources, there is a need for the development of new technologies enabling the distribution network operators to offer new services and functionalities. Smart MV/LV distribution transformers are characterized by a compact three-stage design, including an...
-
Preliminary investigations of effect of conditions of FCAW process on diffusible hydrogen content in deposited metal
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper the state...
-
Pollutants removal effectiveness in hydrophyte filters with sequential vertical and horizontal flow
PublicationThe object of investigations was the constructed wetland in Wiedersberg in Saxonia in Germany supplied with domestic sewage from 145 inhabitants. The biological part was composed of sequential reed beds with vertical and horizontal flow of sewage. It in one of new solutions, because up till now configuration with vertical bed situated at front of biological part of treatment was applied.The evaluation of object performance was...
-
Methodology of the Morphometry Study on Baltic Herring
PublicationAcoustic techniques are used in the estimation of the abundance of Baltic herring. Investigations of the relationship between the Baltic herring individual target strength TS and the total fish length L, significant in the acoustic assessment, demonstrated its de-pendence on the study area location. It motivated the detailed analysis of the relationship between herring from the southern Baltic ICES Subdivisions 24, 25, and 26,...
-
Optical and chemical characterization of thin TiNx films deposited by DC-magnetron sputtering
PublicationThin titanium nitride (tinx) films were deposited on silicon substrates by means of a reactive dc-magnetron plasma. Layers were synthesized under various conditions of discharge power and nitrogen flows in two operation modes of the magnetron (the so-called "balanced" and "unbalanced" modes). The optical constants of the tinx films were investigated by spectroscopic ellipsometry (se). X-ray photoelectron spectroscopy (xps) was...
-
A measurement method for lossy capacitive relative humidity sensors based on a direct sensor-to-microcontroller interface circuit
PublicationA new time-domain measurement method for determining the capacitance and resistance values of lossy relative humidity capacitive sensors is presented. The method is based on a direct sensor-to-microcontroller interface for microcontrollers with internal analog comparators and timers. The interface circuit consists only of four reference resistors (two reference resistors if a microcontroller includes a voltage reference source),...
-
Effect of Simultaneous Valve Closures in Hydraulic Piping Systems
PublicationThe paper investigates wave interference (between pressure waves) occurring in simple hydraulic systems. Water hammer was induced by simultaneous closure of three valves located at the reservoirs of a “Y” type hydraulic system. Numerical simulations were carried out with the help of the freeware computer package Allievi enabling the reader to replicate results in a direct manner. The influence of the following quantities has been...
-
Application of the F-statistic of the Fisher-Snedecor distribution to analyze the significance of the effect of changes in the compression ratio of a diesel engine on the value of the specific enthalpy of the exhaust gas flow
PublicationThe paper discusses the impact of changes in the compression ratio on the operating parameters of a diesel engine, e.g. on the temperature of exhaust gases. It presents the construction of the laboratory test stand, on which experimental measurements were realized. It is characterized how the actual changes of the compression ratio were introduced to the existing engine. The program of experimental investigations taking into account...
-
Environmental risk- based ranking of solvents by the combination of multimedia model and multi-criteria decision analysis
PublicationA novel procedure for assessing the environmental risk related to solvents emissions has been developed. The assessment of risk is based on hazard and exposure detailed investigations. The potential exposure related to different environmental phases is calculated with basic multimedia model, that gives the percentage distribution of solvent in environmental compartments as a result. Specific hazards– toxicological, environmental...
-
Loudness Scaling Tests in Hearing Problems Detection
PublicationThe number of people using portable audio players has increased significantly over the recent years. This implies the rise in the number of people having hearing loss problems. Therefore, there is a need to find appropriate procedures that simplify the process of the hearing problem detection. Investigations performed show that audiometric tests may not be sufficient to assess hearing in young people. Contrarily, the obtained results...
-
New Analogues of Mycophenolic Acid
PublicationMycophenolic acid (MPA) possesses antibacterial, antifungal, antiviral, immunosuppressive and anticancer properties. It is a non-competitive and reversible inhibitor of dehydrogenase inosine-5'-monophosphate (IMPDH). This compound belongs to the immunosuppressive drugs used for the prevention of both acute and chronic transplant rejection. Until now, two derivatives of MPA have been used clinically: mycophenolate mofetil (MMF,...
-
Features extraction from the electrocatalytic gas sensor responses
PublicationOne of the types of gas sensors used for detection and identification of toxic-air pollutant is an electrocatalytic gas sensor. The electrocatalytic sensors are working in cyclic voltammetry mode, enable detection of various gases. Their response are in the form of I-V curves which contain information about the type and the concentration of measured volatile compound. However,...
-
Electric Field-Driven Assembly of Sulfonated Polystyrene Microspheres
PublicationA designed assembly of particles at liquid interfaces offers many advantages for development of materials, and can be performed by various means. Electric fields provide a flexible method for structuring particles on drops, utilizing electrohydrodynamic circulation flows, and dielectrophoretic and electrophoretic interactions. In addition to the properties of the applied electric field, the manipulation of particles often depends...
-
Verification of the Analytical Traffic Model of a Multidomain IMS/NGN Using the Simulation Model
PublicationIn this paper we verify the previously proposed analytical traffic model of a multidomain Next Generation Network (NGN), which is standardized for delivering multimedia services based on the IP Multimedia Subsystem (IMS). For this reason a proper simulation model used, in which not theoretical queuing system models but the operation of real network elements and standardized call scenarios are accurately implemented. Consequently,...
-
The occurrence and role of Nitrospira in nitrogen removal systems
PublicationApplication of the modern microbial techniques changed the paradigm about the microorganisms performing nitrification. Numerous investigations recognized representatives of the genus Nitrospira as a key and predominant nitrite-oxidizing bacteria in biological nutrient removal systems, especially under low dissolved oxygen and substrate conditions. The recent discovery of Nitrospira capable of performing complete ammonia oxidation...