displaying 1000 best results Help
Search results for: ENGINE ROTATION SPEED
-
Methods for evaluating rated power of diesel-powered generator set
PublicationBasic concepts for evaluating rated power of generator sets powered by combustion engines are presented in this article. A relation between parameters of the engine and the generator are shown. Recommendations contained in the standards and technical literature are systematized. The scheme and methodology for evaluating rated power of the generator set, based on laboratory research, are suggested. Also, the main problems which...
-
Operational causes of fatigue failures within the passages of gas turbine engines
PublicationThe short profile of a fatigue wear process of gas turbine engine's constructional elements has been introduced in the article. The primary causes of a fatigue cracks formation within the mechanical system as well as within the passages of the engine have been showed. Especial attention was devoted to the low-cycle fatigue, what is associated with unsteady thermal-flow processes being worked out in the passages.The selected damages...
-
Entropy function application within the selection process of diagnostic parameters of marine diesel and gas turbine engines
PublicationThe paper presents the method of conducting an analysis of the diagnostic informativeness among the parameters characterizing the observed gas dynamic processes carried out within working spaces of marine diesel and gas turbine engines. An entropy function, as the measure of uncertainty of the identified states' set of the engine unfitness was applied. Having evaluated the diagnostic information the most adequate parameters were...
-
SEM examination of surface layer of C45 steel after grinding on defferent depth
Open Research DataFerrite examination for the medium carbon structural steel with low content of Mn, Si, Cu, Cr and Ni after its grinding to a depth of 2 µm, 8 µm, 14 µm and 20 µm, at constant wheel circumferential speed of vs = 25 m/s and constant feed rate vft = 1 m/min. It was shown that the grinding of C45 steel causes strong work hardening of ferrite in surface...
-
Sensorless Multiscalar Control of Five-Phase Induction Machine with Inverter Output Filter
PublicationThe paper presents a complete solution for speed sensorless control system for five-phase induction motor with voltage inverter, LC filter and nonlinear control of combined fundamental and third harmonic flux distribution. The control principle, also known as multiscalar control, nonlinear control or natural variables control, is based on a use of properly selected scalar variables in control feedback to linearize controlled system....
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublicationThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
The Doppler effect in a bistatic system for determining the position of moving targets
PublicationThe article presents the theoretical analysis and the results of numerical calculations of the Doppler effect it occurs in a system designed to determine the position and speed of a moving target. The transmitter is the source of the signal and it emits a sinusoidal, acoustic and continuous wave. Signal reflected off a moving target is received by four hydrophones. Based on the signals, four Doppler shifts are determined and inserted...
-
Determining and visualizing safe motion parameters of a ship navigating in severe weather conditions
PublicationThe paper presents a method of determining, organizing and displaying ship collision avoidance information, which is based on the Collision Threat Parameters Area (CTPA) technique. The method makes it possible to visualize navigational threats as well as possible collision avoidance manoeuvres. The solution is focused on supporting navigation in severe weather conditions. Normally collision avoidance decisions are made taking into...
-
Performance Characteristics of a Micro-Turbine
PublicationIn the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:heat output:...
-
Performance Characteristics of a Micro-turbine, International
Publication. In the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:- heat...
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublicationThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Impact and stretching standardized tests as useful tools for assessment of viscoelastic behavior for highly rubberized asphalt binder
PublicationAsphalt binder is generally identified as a brittle material at low service temperature or under high-speed load, and the brittleness becomes serious after weathering aging. Improving the toughness of asphalt binder through adding high-content of crumb tire rubber is an efficient method to solve this problem. Devulcanized rubber modified asphalt binder (DRMA) with different contents (15–40%) of devulcanized rubber (DR) were prepared...
-
Quantumness in Diagnostics of Marine Internal Combustion Engines and Other Ship Power Plant Machines
PublicationThe article provides proof that the diagnostics of marine internal combustion engines and other ship power plant machines should take into account the randomness and unpredictability of certain events, such as wear, damage, the variations of mechanical and thermal loads, etc., which take place during machine operation. In the article, the energy E, like the other forms (methods) that it can be converted into (heat and work), is...
-
Customization of UWB 3D-RTLS Based on the New Uncertainty Model of the AoA Ranging Technique
PublicationThe increased potential and effectiveness of Real-time Locating Systems (RTLSs) substantially influence their application spectrum. They are widely used, inter alia, in the industrial sector, healthcare, home care, and in logistic and security applications. The research aims to develop an analytical method to customize UWB-based RTLS, in order to improve their localization performance in terms of accuracy and precision. The analytical...
-
Limiting distribution of the three-state semi-Markov model of technical state transitions of ship power plant machines and its applicability in operational decision-making.
PublicationThe article presents the three-state semi-Markov model of the process {W(t): t 0} of state transitions of a ship power plant machine, with the following interpretation of these states: s1 – state of full serviceability, s2 – state of partial serviceability, and s3 – state of unserviceability. These states are precisely defined for the ship main engine (ME). A hypothesis is proposed which explains the possibility of application...
-
Vibration data for 1205 EKTN9 bearings
Open Research DataThe data contains measurements of vibration obtained with VIBstand manufactured by EC systems.
-
Multi-objective weather routing of sailboats considering wave resistance
PublicationThe article presents a method to determine the route of a sailing vessel with the aid of deterministic algorithms. The method assumes that the area in which the route is to be determined is limited and the basic input data comprise the wind vector and the speed characteristic of the vessel. Compared to previous works of the authors, the present article additionally takes into account the effect of sea waves with the resultant resistance...
-
Polarization-dependent optical absorption in phosphorene flakes
PublicationThe interest of 2D materials is constantly increasing because of their very attractive mechanical, electrical and optical parameters. They have been used in many applications, e.g. photodetectors, sensors, modulators, insulators. One of the recently discovered 2D materials is phosphorene. In contrast to graphene, phosphorene has a direct bandgap tuned by numbers of layers in the 2D structure. The phosphorene flakes are strongly...
-
An application of acoustic sensors for the monitoring of road traffic
PublicationAssessment of road traffic parameters for the developed intelligent speed limit setting decision system constitutes the subject addressed in the paper. Current traffic conditions providing vital data source for the calculation of the locally fitted speed limits are assessed employing an economical embedded platform placed at the roadside. The use of the developed platform employing a low-powered processing unit with a set of microphones,...
-
Underwater Navigation System Based on Doppler Shifts of a Continuous Wave
PublicationThe paper describes a concept of an underwater navigation system designed to determine the location and speed of its ROVs or divers. Conducted by the Department of Marine Electronic Systems at the Gdansk University of Technology for several years, research has focused on navigation systems which determine positions on the basis of Doppler shifts of echo signals reflected from a moving object. This article presents a different version...
-
Studies of Nonlinear Sound Dynamics in Fluids Based on the Caloric Equation of State
PublicationThe sound speed and parameters of nonlinearity B/A, C/A in a fluid are expressed in terms of coefficients in the Taylor series expansion of an excess internal energy, in powers of excess pressure and density. That allows to conclude about features of the sound propagation in fluids, the internal energy of which is known as a function of pressure and density. The sound speed and parameters of nonlinearity in the mixture consisting...
-
VIBRATION SURVEILLANCE DURING MILLING OF FLEXIBLE DETAILS WITH A USE OF THE ACTIVE OPTIMAL CONTROL
PublicationThe main goal of modern machining operations is to achieve increasingly better performance. High Speed Machining and/or High Performance Cutting, despite a lot of advantages, have also some drawbacks, for example, a possibility of losing stability and development of self-excited chatter vibration. This paper presents an approach of vibration surveillance during high speed milling with a use of active optimal control. Non-stationary...
-
Non-Salient Brushless Synchronous Generator Main Exciter Design for More Electric Aircraft
PublicationThis paper presents a prototype of high speed brushless synchronous generators (BSG) design for the application in autonomous electric power generation systems (e.g., airplane power grid). Commonly used salient pole field of the main generator part of BSG was replaced with a prototype non-salient pole field. The main objective of the research is an investigation into the advantages and disadvantages of a cylindrical field of the...
-
Determination of the dynamic critical maneuvering area in an encounter between two vessels: Operation with negligible environmental disruption
PublicationThis paper introduces the concept of Collision Avoidance Dynamic Critical Area (CADCA) for onboard Decision Support Systems (DSS). The indicator proposed is derived via identification of a minimum required maneuvering zone in an encounter between two vessels. The CADCA model accounts for ship maneuvering dynamics and associated hydrodynamic actions emerging from different rudder angles and forward speed effects. The method presented...
-
Rotating rod and ball
PublicationWe consider a mechanical system consisting of an infinite rod (a straight line) and a ball (a massless point) on the plane. The rod rotates uniformly around one of its points. The ball is reflected elastically when colliding with the rod and moves freely between consecutive hits. A sliding motion along the rod is also allowed. We prove the existence and uniqueness of the motion with a given position and velocity at a certain time...
-
Modelling of Mechanical Behaviour of High-Frequency Piezoelectric Actuators Using Bouc-Wen Model
PublicationThe paper presents the application of a modified, symmetrical Bouc-Wen model to simulate a mechanical behaviour of high-frequency piezoelectric actuators (PAs). In order to identify parameters of the model, a two-step algorithm was utilized. In the first stage, the mechanical parameters were identified by taking into account their bilinear variability and using a square input voltage waveform. In the second step, the hysteresis...
-
Digital Fingerprinting based on Quaternion Encryption for Image Transmission
PublicationIn this paper a new digital fingerprinting scheme for images is proposed. A proposed method is based on quaternion encryption with Cipher Block Chaining (CBC) mode of operation. Quaternions are hyper-complex numbers of rank 4 and thus often applied to mechanics in three-dimensional space. The encryption algorithm is designed for grey-tone images. For purpose of encryption, the algorithm uses the rotation of data vectors presented...
-
Foucault's pendulum. Uncomplicated tool in the study of geodesy and cartography
PublicationModern education methods often refer to the sophisticated and technologically advanced methods. In the process of education the latest technologies and inventions should be presented. Modern research achievements becomes an indispensable part of the technical studies. However the learning process of an engineer should refer to the standard methods of measurement and well known fundamental instruments. One of the simplest devices...
-
CFD Simulations and Tests of a Prototype Flow Control Valve
PublicationIn this paper a prototype of a flow control valve is described and numerically simulated. The flow control valve is used in hydraulic systems to maintain constant fluid flow despite changing loads of a receiver. The standard construction of this type of valves is modified mainly by eliminating the spring. The prototype consists the hydrostatically unloaded throttle valve and pressure ratio valve substituting pressure difference...
-
Photos of LEGO bricks
Open Research DataRandom photos of the following LEGO bricks: 2419, 2450, 3022, 3031, 4070, 30357, 41682, 44570, 47998, 52107, 54383, 54384, 64799, 87609, 93274, 99206, 99781. The bricks were placed on a white sheet of paper, the photos were taken by hand, using Huawei P20 PRO camera positioned above the bricks. The photos were taken with and without flashlight. The...
-
Enhanced voice user interface employing spatial filtration of signals from acoustic vector sensor
PublicationSpatial filtration of sound is introduced to enhance speech recognition accuracy in noisy conditions. An acoustic vector sensor (AVS) is employed. The signals from the AVS probe are processed in order to attenuate the surrounding noise. As a result the signal to noise ratio is increased. An experiment is featured in which speech signals are disturbed by babble noise. The signals before and after spatial filtration are processed...
-
Obserwatory prędkości dla bezczujnikowego sterowania maszynami prądu przemiennego
PublicationPrzedstawiono model matematyczny uogólnionej maszyny elektrycznej rozszerzony przez wprowadzenie dodatkowych zmiennych. Na podstawie modelu rozszerzonego opracowano strukturę obserwatora prędkości maszyny uogólnionej. Zaprezentowano struktury obserwatorów prędkości dla poszczególnych rodzajów maszyn prądu przemiennego. Pokazano, że prędkość kątową wirnika można odtwarzać dla różnych typów maszyn stosując odpowiednie zmienne stanu...
-
Measures of Functional Reliability of Two-Lane Highways
PublicationRural two-lane highways are the most common road type both in Poland and globally. In terms of kilometres, their length is by far greater than that of motorways and expressways. They are roads of one carriageway for each direction, which makes the overtaking of slower vehicles possible only when there is a gap in the stream of traffic moving from the opposite direction. Motorways and express roads are dual carriageways that are...
-
Consideration of dynamic loads in the determination of axle load spectra for pavement design
PublicationAxle load spectra constitute a crucial part of the data for pavement design and pavement distress analysis. Typically, axle load spectra represent static load from vehicles and do not include dynamic loads generated by vehicles in motion. While dynamic loads can significantly contribute to faster pavement distress, this fact is mostly omitted in pavement design methods. The paper presents a methodology for consideration of dynamic...
-
Effect of Base-Connection Strength and Ductility on the Seismic Performance of Steel Moment-Resisting Frames
PublicationColumn-base connections in steel moment-resisting frames (SMFs) in seismic regions are commonly designed to develop the capacity of adjoining column with an intent to develop a plastic hinge in the column member, rather than in the connection (i.e., a strong-base design). Recent research has shown base connections to possess high ductility, indicating that this practice may be not only expensive but also unnecessary. This suggests...
-
BEZCZUJNIKOWE STEROWANIE WOLNOOBROTOWYM SILNIKIEM PMSM Z KOMPENSACJĄ MOMENTU ZACZEPOWEGO
PublicationW pracy przedstawiono propozycję rozwiązania problemu bezczujnikowego sterowania wolnoobrotową maszyną synchroniczną z magnesami trwałymi PMSM. Przedstawiono silnik PMSM, który zastosowano w stanowisku badawczym. Omówiono problem występowania tętnień momentu napędowego wynikający głównie ze znacznego momentu zaczepowego. Pokazano rozwiązanie kompensujące tętnienia momentu napędowego w silniku PMSM. Przygotowano procedurę startową...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
AeroSense Measurements: Wind Tunnel ETH Zurich
Open Research DataData from wind tunnel tests of Aerosesne measurement system installed on NACA 0012 at ETH Zurich wind tunnel.
-
Constant vs. Variable Efficiency of Electric Drive in Train Run Simulations
PublicationTrain run simulations, which focus on various power- and energy-oriented aspects, should reflect the losses in the electric powertrain. In general, the powertrain efficiency varies with respect to load and speed. Including this relation in simulation requires knowledge about detailed drivetrain parameters, which are often unavailable. This paper verifies the possibility to approximate the drivetrain efficiency in train run simulations...
-
A Target Information Display for Visualising Collision Avoidance Manoeuvres in Various Visibility Conditions
PublicationThe paper introduces a new approach to displaying information on targets. The proposed display visualises three types of information: targets’ motion parameters (typical for target tracking), combinations of own course and speed which collide with those targets (typical for Collision Threat Parameters Area display by Lenart (1983)) and combinations of own course and speed which are not compliant with COLREGS in this case (based...
-
Analysis and design improvement of high class roads’ arched sections in Poland
PublicationAlthough Polish road network standards, in particular higher classes of roads are improving dynamically the number of fatalities on the network is still higher that EU’s average. Ensuring road safety and high maintaining standards is a complex issue and one that poses a major challenge for all road authorities. Road accidents at high speed roads characterize specially serious material and social consequences, thus research into...
-
Z type Observer Backstepping For Induction Machines
PublicationThis paper contains a relatively new synthesis method for non-linear objects, named backstepping. This method can be used to obtain the observer structure. The paper presents the structure of the speed observer which is a new proposition of observer backstepping with additional state variables marked Z. The rotor speed can be estimated in three different ways. The first is based on the adaptive approach, the second on the nonadaptive...
-
Changes in conditions of acoustic wave propagation in the Gdansk deep as an effect of climate changes in the Baltic Sea region
PublicationThe article presents the results from a research project investigating acoustic climate changes in the Gdansk Deep based on data extending from 1902 to 2019. This part of the southern Gotland Basin, is rarely discussed in the scientific literature. The speed of sound in the seawater is a function of temperature, salinity, and depth. In such shallow sea as Baltic Sea, the impact of depth is not substantial. The other two factors...
-
The effect of a belt position in the spindle driving system on critical rotational speeds
PublicationThe aim of this paper was to examine how the belt pulley position affects critical rotational speeds of the modernized spindle of the sliding table saw Fx3. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented. Spindles in these kind of machine tools are mainly driven with V-belts, and the pulleys on the spindles might be positioned:...
-
Experimental analysis of chip removing system in circular sawing machine
PublicationPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
Dual drive control under SVPWM, experimental results
Open Research DataThe dataset contains the experimental results of the project: A universal algorithm of space vector pulse width modulation for three-level three and multi-phase NPC inverters with DC-link voltage balancing. The analysis includes the behaviour of the drive system, examining the dynamic system response to speed and angle changes, and encompassing data...
-
Atmospheric deposition of microplastics in the coastal zone: Characteristics and relationship with meteorological factors
PublicationThe quantitative and qualitative compositions of microplastics (MPs) deposited from the atmosphere in the coastal zone were analysed. Moreover, links between MP deposition and meteorological factors (air humidity, wind speed, precipitation height, and air mass trajectories) were investigated
-
Catena-Poly[{[mu]-[eta]5:[eta]5-1-[2-(dimethylamino)ethyl-[kappa]N]cyclopentadienyl}-lithium(I)-([mu]-1,1,3,3-tetra-tert-butyltriphosphane-[kappa]3P2:P1,P3)lithium(I)]
PublicationThe title compound, [Li2(C9H14N)(C16H36P3)]n, is a by-product of the reaction of [Cp(C5H4CH2CH2NMe2)ZrCl2]n with tBu2P-P(SiMe3)Li in toluene. It is a coordination polymer composed of infinite chains running along [010]. One Li(I) atom is chelated by the cyclopentadienyl ring and and the N atom of the scorpionate ligand and a P atom, whereas the other Li(I) atom is coordinated by the backside of the cyclopentadienyl ring and two...
-
An Analysis of Uncertainty and Robustness of Waterjet Machine Positioning Vision System
PublicationThe paper presents a new Automatic Waterjet Positioning Vision System (AWPVS) and investigates components of workpiece positioning accuracy. The main purpose of AWPVS is to precisely identify the position and rotation of a workpiece placed on a waterjet machine table. Two webcams form a basis for the system, and constitute its characteristics. The proposed algorithm comprises various image processing techniques to assure a required...
-
Efficient analysis of structures with rotatable elements using model order reduction
PublicationThis paper presents a novel full-wave technique which allows for a fast 3D finite element analysis of waveguide structures containing rotatable tuning elements of arbitrary shapes. Rotation of these elements changes the resonant frequencies of the structure, which can be used in the tuning process to obtain the S-characteristics desired for the device. For fast commutations of the response as the tuning elements are rotated, the...
-
Polarimetric studies of L-arginine-doped potassium dihydrogen phosphate single crystals
PublicationConoscopic interference patterns, channelled spectra and polarimetric techniques have been used for the characterization of pure and doped (with L-arginine amino acid) potassium dihydrogen phosphate (KDP) single crystals. Experimental polarimetric data have been obtained for the frequently used wavelength of 633 nm and for two close wavelengths of 532 and 543 nm in a high-accuracy dual-wavelength polarimeter. The measurement of...
-
The methodology of design of satellite working mechanism of positive displacement machine
PublicationIn this paper is described a methodology of design of satellite mechanism consisting of two noncircular gears (externally toothed rotor and internally toothed curvature) and circular gears (satellites). In the presented methodology is assumed that the rotor pitch line is known, and the curvature pitch line is necessary to designate. The presented methodology applies to mechanisms for which the number of the curvature humps is at...
-
On Radar DoA Estimation and Tilted Rotating Electronically Scanned Arrays
PublicationWe consider DoA estimation in a monopulse radar system employing a tilted rotating array. We investigate the case of nonzero steering angles, in which case the mapping between the target’s azimuth and elevation in the global coordinate system and their counterparts in the array local coordinate system becomes increasingly nonlinear and coupled. Since estimating the azimuth using coherently integrated signals might be difficult because...
-
Performance evaluation of Unified Memory with prefetching and oversubscription for selected parallel CUDA applications on NVIDIA Pascal and Volta GPUs
PublicationThe paper presents assessment of Unified Memory performance with data prefetching and memory oversubscription. Several versions of code are used with: standard memory management, standard Unified Memory and optimized Unified Memory with programmer-assisted data prefetching. Evaluation of execution times is provided for four applications: Sobel and image rotation filters, stream image processing and computational fluid dynamic simulation,...
-
Energy Systems Stations, W, ET, sem.7, zimowy 22/23 (PG_00042106)
e-Learning CoursesInternal combustion engines - principle of operation and classification. Heat balance of the engine. Uniform and combined propulsion systems.The main comonents of the propulsion system. Power plant efficiency and waste heat utilization. Cooling water system, lubricating oil system, fuel oil systeml, gaseos fuel system (LNG), compressed air system, exhaust gas system. Fittings and accessories of pipeline systems in the power plant....
-
Thermodynamic Cycles of Air Microturbine Power Plants Working on Biomass Fuels
PublicationThe gas turbine engine is modified to work as an air turbine set which consists, in the simplest arrangement, of a compressor, a heat exchanger and a turbine. Air is a working medium for both: the compressor and the turbine. This kind of air turbine set can be applied in power plants working on biomass fuels. In this solution we can burn fuels of varying parameters in the external combustion chamber without any harmful effects...
-
Changes in Manufacturing Industries- an Empirical Verifiction of the Kaldor-Verdoorn Laws
PublicationThis paper focus on showing the importance of manufacturing industry for the growth of selected european countries from a kaldorian perspective. the author discusses and testes two (the first and the second) kaldor-verdoorn laws, which state that manufacturing is the engine of growth (the first law) and that exist positive relation between labour productivity and output in manufacturing industries because of increasing returns...
-
Review of methods for assessing traffic conditions on basic motorway and expressway sections
PublicationMotorways and expressways are the core of each country’s road system. Road planning, design and management requires tools to ensure that roads have the right geometry, traffic layout and equipment. These include methods for capacity estimation and assessing traffic conditions. Because the paper focusses on the basic segments of motorways and expressways (sections located between interchanges and outside of their influence), its...
-
Effects of Road Infrastructure on Pedestrian Safety
PublicationThe objective of the work was to identify risks for pedestrians that involve road infrastructure and roadside and to define how selected elements of geometry and traffic layout affect driver behaviour (speed on approaching pedestrian crossings). The results have helped to formulate recommendations on pedestrian crossing design. The research included an analysis of 2013-2017 statistics to identify the...
-
Wpływ błędów parametrów modelu maszyny indukcyjnej na działanie rozszerzonego obserwatora prędkości
PublicationW artykule opisano metodę odtwarzania prędkości wirnika maszyny indukcyjnej przy wykorzystaniu rozszerzonego obserwatora prędkości. Zbadano wpływ błędów parametrów modelu maszyny indukcyjnej na właściwości dynamiczne obserwatora poprzez porównanie macierzy stanu obserwatora obarczonego oraz nieobarczonego błędami parametrów. Zbadany został także wpływ błędów parametrów na jakość odtwarzania zmiennych maszyny w stanie ustalonym.
-
Satelitowy agregat pompowy
PublicationW artykule opisano najnowszą konstrukcję satelitowego agregatu pompowego charakteryzującego się tym, że pompa satelitowa jest umieszczona wewnątrz silnika elektrycznego i zasysa ciecz poprzez otwór wydrążony osiowo w wale silnika. Zastosowana w agregacie pompa satelitowa jest nowatorską konstrukcją zawierającą mechanizm satelitowy o odwróconej kinematyce znamienny tym, że planeta (wirnik) oraz płyty kompensacyjne (rozrządu) są...
-
An Efficient Simulation Method of Massive MIMO Antenna Arrays used in 5G Mobile Phones
PublicationThis paper deals with a model-order reduction method, applied to speed-up the simulations of MIMO antenna arrays, performed by means of finite element method. The obtained results of the numerical tests show that the described technique is reliable and considerably increases the efficiency of the standard finite element method.
-
Estimating Traffic Intensity Employing Passive Acoustic Radar and Enhanced Microwave Doppler Radar Sensor
PublicationInnovative road signs that can autonomously display the speed limit in cases where the trac situation requires it are under development. The autonomous road sign contains many types of sensors, of which the subject of interest in this article is the Doppler sensor that we have improved and the constructed and calibrated acoustic probe. An algorithm for performing vehicle detection and tracking, as well as vehicle speed measurement,...
-
Changes in conditions of acoustic wave propagation in the Gdansk deep as an effect of climate changes in the Baltic Sea region
PublicationThe article presents the results from a research project investigating acoustic climate changes in the Gdansk Deepbased on data extending from 1902 to 2019. This part of the southern Gotland Basin, is rarely discussed in thescientific literature.The speed of sound in the seawater is a function of temperature, salinity, and depth. In such shallow sea asBaltic Sea, the impact of depth is not substantial....
-
Reduction of Tire Rolling Resistance by Optimization of Road Surfaces and Tires
PublicationDuring interaction between tire and road surface three very important phenomena are always in effect. One of them (very desirable) is friction that is important for traction, braking and cornering. Two other phenomena are not desirable at all, that is rolling resistance and noise. This paper discusses relations between road surface and tire parameters versus tire rolling resistance. Road surface texture, porosity, impedance, strength...
-
Optimization of Bread Production Using Neuro-Fuzzy Modelling
PublicationAutomation of food production is an actively researched domain. One of the areas, where automation is still not progressing significantly is bread making. The process still relies on expert knowledge regarding how to react to procedure changes depending on environmental conditions, quality of the ingredients, etc. In this paper, we propose an ANFIS-based model for changing the mixer speed during the kneading process. Although the...
-
Sensorless control system of induction machine supplied by voltage source inverter with output filter
PublicationThe paper focuses on sensorless control of the induction machines supplied by inverter with the output filters. “The novel” idea of the speed observer which is based on the backstepping approach is shown. The standard structure of the exponential observer is extended by the integrators and additional Z vector. The simulation and experimental results validate the proposed solution.
-
Recognition of hazardous acoustic events employing parallel processing on a supercomputing cluster . Rozpoznawanie niebezpiecznych zdarzeń dźwiękowych z wykorzystaniem równoległego przetwarzania na klastrze superkomputerowym
PublicationA method for automatic recognition of hazardous acoustic events operating on a super computing cluster is introduced. The methods employed for detecting and classifying the acoustic events are outlined. The evaluation of the recognition engine is provided: both on the training set and using real-life signals. The algorithms yield sufficient performance in practical conditions to be employed in security surveillance systems. The...
-
RSVP-TE as a reservation protocol for optical networks
PublicationIn this paper, we consider the reservation of optical resources problem. We implement extensions for RSVP-TE (Resource ReSerVation Protocol with Traffic Engineering Extension) to achieve the new functionality for optical resources reservation. Based on ASON/GMPLS architecture we examine an open source implementation KOM RSVP-Engine and extend its functionality according to ITU-T and IETF recommendations. The transport plane consists...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publicationin view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
Analiza działania rozszerzonego obserwatora prędkości w szerokim zakresie zmian prędkości maszyny indukcyjnej
PublicationW artykule przedstawiono zagadnienia związane z odtwarzaniem zmiennych stanu maszyny indukcyjnej. Wykorzystano obserwator oparty na modelu matematycznym maszyny z dodatkowymi zmiennymi. Przedstawiono macierz stanu zlinearyzowanych równań błędu odtwarzania. Opisano sposób definiowania wyznacznika jakości na podstawie rozkładu biegunów obserwatora. Zaproponowano metodę korekcji wzmocnień wraz ze zmianą warunków pracy maszyny. Wykazano...
-
Testbed for development and verification of hybrid localization systems
PublicationIn this paper a testbed for development and verification of hybrid localization systems is presented. It allows for systematic analysis of hybrid localization methods and speed up the development of new schemes. The proposed testbed platform is composed of subsystem for sequential data collection and testing infrastructure that can be used for investigating the localization mechanisms in controllable environment.
-
Aggregated conducted interferences generated by group of asynchronous drives with deterministic and random modulation
PublicationThis paper addresses problems linked with electromagnetic interferences generated by group of three adjustable speed drives fed by frequency converters with deterministic and random modulation. Based on the experimental results it has been shown that decreasing of the conducted interferences in a case of random modulation is measuring phenomenon linked with selectivity of the EMI receiver.
-
NEW DESIGNS OF CENTRIFUGAL MAGNETIC FLUID SEALS FOR ROTATING SHAFTS IN MARINE TECHNOLOGY
PublicationThe centrifugal magnetic fluid seals have important advantage over the conventional centrifugal seals. They maintain very good sealing capacity at static, medium and high speeds of shaft rotation, with the increased seal lifetime, and minimum torque and static friction. These seals are particularly useful in cases when the angular shaft velocity varies and sometimes decreases to nearly or exactly zero, such as in flywheel applications,...
-
Digital Fingerprinting Based on Quaternion Encryption Scheme for Gray-Tone Images
PublicationIn this paper a new idea of digital images fingerprinting is proposed. The method is based on quaternion encryption in the Cipher Block Chaining (CBC) mode. Quaternion sare hyper-complex numbers of rank 4 and thus often applied to mechanics in three-dimensional space. The encryption algorithm described in the paper is designed for gray-tone images but can easily be adopted for color ones. For the encryption purpose, the algorithm...
-
2-D constitutive equations for orthotropic Cosserat type laminated shells in finite element analysis
PublicationWe propose 2-D Cosserat type orthotropic constitutive equations for laminated shells for the purpose of initial failure estimation in a laminate layer. We use nonlinear 6-parameter shell theory with asymmetric membrane strain measures and Cosserat kinematics as the framework. This theory is specially dedicated to the analysis of irregular shells, inter alia, with orthogonal intersections, since it takes into account the drilling...
-
Longitudinally magnetized left-handed cylindrical ferrite coupled line junction for nonreciprocal devices
PublicationThis paper presents investigations of longitudinally magnetized left-handed cylindrical ferrite coupled line junction for nonreciprocal devices. The proposed junction is formed as a quasi periodic arrangement of N unit cells. Each unit cell is realized as a cascade of short cylindrical ferrite coupled lines with reactance circuit composed of series capacitors and parallel inductors. The left-handed cylindrical junction with π/4...
-
<i>N,N,N</i>-Trimethyl-N-(methyl 5-deoxy-2,3-<i>O</i>-isopropylidene-β-D-ribofuranosid-5- yl)ammonium 4-methylbenzenesulfonate sesquihydrate.
PublicationThe structure of the title compound, [C12H24NO4][C7H7O3S]·1.5H2O, contains alternating layers parallel to (001) of hydrophobic and polar character, stabilized by C-H...O hydrogen bonding. The furan ring adopts an envelope conformation with the C(OMe) atom as the flap, and the dioxolane ring is twisted about one of the O-C(methine) bonds. A comparison to related compounds is presented. The tosylate-O atoms were disordered over two...
-
The effect of thermal modification on the quality of the milled surface of beech and pine wood
PublicationThe article deals with the effect of thermal modification on the quality of the created surface during milling on CNC milling cutters. The quality of the created surface is evaluated based on surface roughness, specifically its roughness parameter Ra. The observed surface is created by a shank cutter with a diameter of 20 mm and three cutting edges in a spiral at a standard speed of 18,000. min-1. The article compares thermally...
-
Losses and energy efficiency of drive motors and systems
PublicationLosses and energy efficiency of every drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the machine or device driven by the motor, changing in the drive operating field. Speed and load of the motor decide of the instantaneous useful power of the motor and also in a differentiated way of kinds and values of losses occurring in the...
-
Losses and energy efficiency of drive motors and systems
PublicationLosses and energy efficiency of every drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the machine or device driven by the motor, changing in the drive operating field. Speed and load of the motor decide of the instantaneous useful power of the motor and also in a differentiated way of kinds and values of losses occurring in the...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublicationThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Influence of friction stir welding technological parameters on the properties of the joints of selected aluminum alloys
PublicationThe purpose of this dissertation was to determine the effect of friction stir welding technological parameters on the properties of selected aluminum alloy joints, with consideration of the residual stresses and dislocation density in the joints. The goal of the present work was also to produce defect-free joints with high mechanical and electrochemical properties. In the dissertation, similar welds of AA6082 alloy and dissimilar...
-
Improving Output Performance of the Ultrasonic Multicell Piezoelectric Motor by Development the Multi-Rotor Structure
PublicationIn recent years, many researches have been carried out on piezoelectric multi-rotor structures. This paper describes the analysis, development and experimental process of an ultrasonic multi-cell piezoelectric motor using a multi-rotor structure. In this design, three independent cells have been integrated into a mechatronic system. Analytical model and finite element method are used for modal and dynamic analysis of the proposed...
-
Appendix E
PublicationThe advance of variable speed drives systems (VSDs) engineering highlights the need of specific technical guidance provision by electrical machines and drives manufacturers, so that such applications can be properly designed to present advantages in terms of both energy efficiency and expenditure. This book presents problems and solutions related to inverter-fed electrical motors. Practically orientated, the book describes the...
-
Experimental Study of Silent Sonar
PublicationStealth is a frequent requirement in military applications and involves the use of devices whose signals are difficult to intercept or identify by the enemy. The silent sonar concept was studied and developed at the Department of Marine Electronic Systems of the Gdansk University of Technology. The work included a detailed theoretical analysis, computer simulations and some experimental research. The results of the theoretical...
-
Tyre rolling resistance and its influence on fuel consumption
PublicationRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Fracture in composite/aluminium joints of variable adhesive properties
PublicationA strain gauge technique recently developed with the wedge test, for estimating crack length and, thus, the fracture energy of structural adhesive bonding, has been employed on a system in which one adherend had two types of surface treatment. Simple polishing and polishing with subsequent sandblasting were the treatments used, with a distinct straight line, perpendicular to the sample edges, separating the two. Despite the clear-cut...
-
Energy losses in hydrostatic drive:Drive investigation method compatible with diagram of power increase opposite to the direction of power flow
PublicationEnergy losses and efficiency of drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the driven device, changing in the drive operating field. Speed and load decide of the useful power and, in differentiated way, of kinds and values of losses in the motor. But energy losses and efficiency of drive motors are evaluated as functions of...
-
Practical Eco-Driving Strategy for Suburban Electric Multiple Unit
PublicationIn this paper, a practical approach to velocity profile optimization for electric multiple unit was presented. The study focuses on a case of fast urban railway, which is a popular mean of transport across Tricity, Poland. Based on observations and measurements, a potential for improvement of energy efficiency by modifying the speed profile was recognized. In order to conduct necessary calculations, simulation model of railway...
-
Determination of the Theoretical and Actual Working Volume of a Hydraulic Motor—Part II (The Method Based on the Characteristics of Effective Absorbency of the Motor)
Publication: In this article, the second method of determination of the theoretical and actual working volume of a hydraulic motor is described. The proposed new method is based on the characteristics of effective absorbency of the motor. The effective absorbency has been defined as the ratio of flow rate in a motor to the rotational speed of the motor’s shaft. It has been shown that the effective absorbency is a nonlinear function of the...
-
HYBRID ENERGY SYSTEM FOR A CLASSIC SHIP POWER PLANT
PublicationThe article presents a brief overview of hybrid energy systems used on ships. The area of their application is outlined. The benefits of using such systems are also indicated. Then, the classic ship power plant is defined. The most important part of the article is a proposal how to modify a classic engine room by using a hybrid energy system. The idea is: to accumulate a part of electricity in areas where it is allowed to burn...
-
Analiza możliwości zastosowania środowiska SCILAB do wspomagania projektowania podsystemów energetycznych statków = Analysis of capability of using SCILAB for adding design of power ship subsystems
PublicationW artykule przedstawiono koncepcję wykorzystania środowiska symulacyjnego Scilab, modeli matematycznych oraz badań symulacyjnych przy projektowaniu podsystemów energetycznych statku. Zredagowano przykładową strukturę zawierającą model wysokoprężnego silnika oraz model śruby okrętowej. Przedstawione procedury oraz modele matematyczne zostaną włączone do systemu ekspertowego wspomagającego projektowanie statków. This paper deals...
-
Risk criteria for sea-going ships arising from the operation of the main engines' crankshaft - conecting rod - piston systems
PublicationIn the article the risk criterion for sea-going ships arising from the operation of the main engines' crankshaft - connecting rod - piston systems is proposed. These criterion is based on the procedures recommended in the Formal Safety Assessment method developed under the auspices of International Maritime Organization (IMO). First of all the collective risk criterion for ship has been proposed. In the next step, the share of...
-
COMPREHENSIVE MODELLING OF THE COST EFFECTIVNESS OF RAILWAY LINE ELECTRIFICATION
PublicationSubject of this paper is the mathematical model estimating the Economical threshold between usage of combustion engine traction and electrical traction for new and modernized railway passenger communication lines. Currently available models do not coincide with the whole complexity of the problem. The proposed model was implemented into Matlab and then validated on “Pomorska Kolej Metropolitalna” investment time-frame and its cost...
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublicationPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
WZROST ZATRUDNIENIA W PRZEDSIĘBIORSTWACH MSP problemy badawcze i wyniki
PublicationW artykule w pierwszej kolejności przedstawiono główne problemy badawcze związane z zagadnieniem wzrostu i rozwoju przedsiębiorstwa, wskazując na najczęściej stosowane rozwiązania metodyczne w tym zakresie. W dalszej części zaprezentowano wyniki badań empirycznych, dotyczące zmian zatrudnienia oraz planów związanych z rozwojem małych i średnich przedsiębiorstw funkcjonujących na Pomorzu (badania zostały przeprowadzone w 2009 i...
-
Emotion Recognition
Open Research DataThe films presented here were recorded using so-called high-speed camera Phantom Miro. To play the movie You need the special software which can be downloaded from the web site https://www.phantomhighspeed.com/resourcesandsupport/phantomresources/pccsoftware the details of the movie are available after starting the movie in the viewer in the description...
-
Emotion Recognition
Open Research DataThe films presented here were recorded using so-called high-speed camera Phantom Miro. To play the movie You need the special software which can be downloaded from the web site https://www.phantomhighspeed.com/resourcesandsupport/phantomresources/pccsoftware the details of the movie are available after starting the movie in the viewer in the description...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublicationA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...