Filters
total: 2704
filtered: 2065
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: REED BEDS
-
Simulation of Parallel Applications on Large-scale Distributed Systems
PublicationThis chapter has a form of a review article in the field of simulating High-Performance Computing systems. We justify the need for a new versatile simulator considering heterogeneity, energy efficiency and reliability of HPC systems. We sketch the problems that need to be solved by such simulator and rationalize using discrete-event simulation for this purpose. Based on a review of existing discrete-event HPC simulation solutions...
-
Trwałość spawanych instalacji wodnych wykonanych z nierdzewnych stali austenitycznych
PublicationW artykule przedstawiono dwa przypadki przedwczesnych uszkodzeń spawanych instalacji wodnych wykonanych ze stali odpornych na korozję. W celu ustalenia przyczyn uszkodzenia instalacji przeprowadzono badania metalograficzne, makro - i mikroskopowe oraz mikroanalizę składu chemicznego EDS na próbkach pobranych z reprezentatywnych miejsc. Wykazano, że głównymi przyczynami awarii rurociągów wody pitnej były niezgodności spawalnicze,...
-
Evaluation of Praseodymium and Gadolinium Doped Ceria as a Possible Barrier Layer Material for Solid Oxide Cells
PublicationIn this work, nanocrystalline layers based on the Pr, Gd co-doped CeO2 were investigated. For the preparation of thin layers, lowtemperature spray pyrolysis technique was used. Different stoichiometries of the layers were produced for comparison on polished sapphire substrates. The microstructure of the prepared thin layers was studied by scanning electron microscopy (SEM), energydispersive X-ray spectroscopy (EDS) and X-ray diffractometry (XRD)....
-
Treatment Wetland for Overflow Stormwater Treatment: The Impact of Pollutant Particles Size
PublicationThe problem of stormwater treatment in urban areas has become increas- ingly crucial. It has been widely recognized that both mechanical and biological treatment of stormwater is necessary to protect surface water against pollution. Moreover, technology must be applied to ensure effective treatment in changing hydraulic conditions and to serve, to the extent possible, as a retention volume. Treatment wetland (TW) could be...
-
The home-made in situ passive flux sampler for the measurement of monoterpene emission flux: preliminary studies
PublicationThe paper presents the construction and metrological characteristics of the home-made in situ passive flux sampler, an analytical tool representing small-scale emission chambers working in situ and passively sampling analytes from the gaseous phase. The sorption element was a cylindrical container made of stainless steel net, packed with a carbon sorbent bed-graphitized charcoal, Carbograph 4 (35/50mesh). The recommended working/exposure...
-
Rapid and simple multi-analyte LC–MS/MS method for the determination of benzodiazepines and Z-hypnotic drugs in blood samples: Development, validation and application based on three years of toxicological analyses
PublicationBenzodiazepines (BZDs) and Z-drugs have been particularly important treatments for sleeping and anxiety disorders for many years. However, recently, a number of new benzodiazepines (named designer benzodiazepines, DBZDs) were synthesised, but some of them have never been used in the clinic; they reached the black drug market as new psychoactive substances and are used for recreational purposes. The abuse of these substances has...
-
Relationship between the betalain composition in Opuntia ficus indica and Beta vulgaris varieties and biological activity of their extracts
PublicationBetalains are a class of pigments that are much less com- monly found in nature than anthocyanins or carotenoids. They occur only in a few edible plants such as red beetroot (Beta vulgaris), prickly pears (Opuntia ficus indica), amaranth (Amaranthus sp.) and some mushrooms. This group of pig- ments can be divided into two major groups: yellow vulgax- anthins and red betanins. Despite their structural similarity to compounds from...
-
Application of wavelength division multiplexing in sensor networks
PublicationOver the past few years the need to acquire data on various parameters from a number of sensors grew. The need that led to the development of a network of sensors which enables simultaneous control and measurement in a wide range of applications. The aim of this article is to discuss a possibility of connecting a variety of sensors in a network that would utilize WDM technology. Wavelength Division Multiplexing is commonly used...
-
Adaptive traffic optimization using Variable Speed Limits; Adaptacyjna optymalizacja ruchu drogowego przy pomocy zmiennych ograniczeń prędkości
PublicationVariable speed limits (VSL) is an intelligent transportation system (ITS) solution for traffic management. The speed limits can be changed dynamically in order to adapt to traffic, weather, or road surface conditions. This paper presents an approach for such an adaptive traffic control where the primary goal is to ensure traffic safety and efficiency of the traffic control system (fast response to dynamically changing traffic,...
-
Chitin and derivative chitosan-based structures — Preparation strategies aided by deep eutectic solvents: A review
PublicationThe high molecular weight of chitin, as a biopolymer, challenges its extraction due to its insolubility in the solvents. Also, chitosan, as the N-deacetylated form of chitin, can be employed as a primary material for different industries. The low mechanical stability and poor plasticity of chitosan films, as a result of incompatible interaction between chitosan and the used solvent, have limited its industrialization. Deep eutectic...
-
Intracranial electrophysiological recordings from the human brain during memory tasks with pupillometry
PublicationData comprise intracranial EEG (iEEG) brain activity represented by stereo EEG (sEEG) signals, recorded from over 100 electrode channels implanted in any one patient across various brain regions. The iEEG signals were recorded in epilepsy patients (N=10) undergoing invasive monitoring and localization of seizures when they were performing a battery of four memory tasks lasting approx. 1 hour in total. Gaze tracking on the task...
-
Structural and luminescence properties of B2O3-Bi2O3-AlF3 glass doped with Eu3+, Tb3+ and Tm3+ ions
PublicationThe B2O3-Bi2O3-AlF3 glass system doped with Eu3+, Tb3+, Tm3+ and triply doped with Eu3+/Tm3+/Tb3+ ions in different molar ratios were successfully synthesized. Glass transition and crystallization temperatures were examined by Differential Scanning Calorimetry (DSC) measurements. X-ray Diffraction (XRD) confirmed the amorphous character of the samples. Fourier Transform Infrared Spectroscopy (FTIR) revealed that the glass matrix...
-
“Project-factor-decision”. Decisive factors in IT projects and their impact on its success
PublicationThe aim of this article is to indicate the need for a deepening, systematizing and codifying of the theoretical and practical knowledge on IT project management, in the area of management decision-making processes. The scope of decisions made by managers is constantly on the increase. Project managers make decisions not only within the classic triangle of constraints, which consists of a schedule, a budget and the project scope,...
-
The concept of research on ecological, energy and reliability effects of modified marine fuel oils application to supply compression-ignition engines in real conditions
PublicationWithin the article, basic assumptions of the research project financed by Regional Fund for Environmental Protection and Water in Gdansk were described. The project concerns the experimental investigations carried out on laboratory compression-ignition engine in conditions of its supply with a non-standard marine fuel oil. Configuration and measuring capability of laboratory test bed presently being constructed were introduced....
-
Temperature Impact of Nitrogen Transformation in Technological System: Vertical Flow Constructed Wetland and Polishing Pond
PublicationThe article describes the results of the research, purpose of which was to evaluate influence of the temperature on the effectiveness of nitrification and denitrification in the sewage treatment system consisting of vertical flow constructed wetland and polishing pond. During the analysed period, the efficiency of removing total nitrogen was low and amounted to 12.7%. In the polishing pond in the summer period, content of total...
-
Substrate Dependence in the Formation of Au Nanoislands for Plasmonic Platform Application
PublicationIn this work, the influence of the various substrates on Au nanoisland formation has been studied. Nanostructures were obtained via annealing of thin Au films. In order to determine nanoisland formation mechanisms, correlation between an initial film thickness and temperature of formation, shapes, and dimensions of nanostructures was examined. For the surface morphology studies, nanograin structure, and chemical composition analysis,...
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublicationIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
A Low-Profile Metal-backed Dipole Loaded with Closely Coupled Arc-shaped Open Stubs for On-metal Tag Design with Wide Frequency Tuning Capability
PublicationThis research has presented a single-layer metal-backed dipole antenna, which consists of a feedline loaded with two pairs of closely-coupled arc-shaped open stubs, for designing a metal-mountable tag that features tuning capability over a wide range of frequency. Here, the stubs can generate sufficient inductive reactance for bringing down the tag resonant frequency tunable in both the regulated UHF RFID passbands (North American...
-
Enhancing the bioconversion rate and end products of black soldier fly (BSF) treatment – A comprehensive review
PublicationFood security remains a pressing concern in the face of an increasing world population and environmental challenges. As climate change, biodiversity loss, and water scarcity continue to impact agricultural productivity, traditional livestock farming faces limitations in meeting the growing global demand for meat and dairy products. In this context, black soldier fly larvae (BSFL) have emerged as a promising alternative for sustainable...
-
First highly effective non-catalytic nitrobenzene reduction in UV/dithionite system with aniline production – Advanced reduction process (ARP) approach
PublicationAdvanced reduction processes (ARPs) are currently intensively investigated as an alternative to Advanced Oxidation Processes (AOPs). The study presents efficient reduction of nitrobenzene under non-catalytic conditions through reaction with free radicals having reductive potential. Effective conversion of nitrobenzene in a model wastewater solution, was obtained for sodium dithionite (SDT)/ dithionite (DTN). The developed process...
-
Knowledge work and knowledge workers in knowledge-based economy - theoretical considerations
PublicationIt is often claimed that an organization is as good as people working in it and that talented workers are the driving force of an organization. To cope with the growing requirements of knowledge-based economy, organizations need a special type of workers - knowledge workers. This is especially important in organizations building their competitive advantage on innovations and the application of information and communication technologies...
-
Activated Carbon Produced by Pyrolysis of Waste Wood and Straw for PotentialWastewater Adsorption
PublicationPyrolysis of straw pellets and wood strips was performed in a fixed bed reactor. The chars, solid products of thermal degradation, were used as potential materials for activated carbon production. Chemical and physical activation processes were used to compare properties of the products. The chemical activation agent KOH was chosen and the physical activation was conducted with steam and carbon dioxide as oxidising gases. The eect...
-
Morphology and properties of nanotubular oxide layer on the Ti13Zr13Nb alloy
PublicationThe Ti13Zr13Nb alloy in solid and porous form was oxidised. The constant voltage 20 V, oxidation time 0.5 and 1 h, and 1 M H3PO4 (orthophosphoric acid) with addition of HF (hydrofluoric acid) as a test solution were applied. SEM (Scanning Electron Microscope) examinations of surface, EDS (Energy Dispersive X-ray Spectroscopy) chemical analysis, nanohardness and nano-scratch tests, and corrosion potentiokinetic tests at various...
-
Characterization of CaTi0.9Fe0.1O3/La0.98Mg0.02NbO4 composite
PublicationA composite of CaTi0.9Fe0.1O3 and electrolyte material, i.e. magnesium doped La0.98Mg0.02NbO4 was prepared and studied. The phase content and the sample microstructure was examined by an X-ray diffraction method and scanning electron microscopy. EDS measurements were done both for composite samples and the diffusion couple. The electrical properties were studied by four terminal DC method. The Ahigh-temperature interaction between...
-
Failure of austenitic stainless steel tubes during steam generator operation
PublicationThe article presents the failure process of austenitic stainless steels used in power devices, such as heat exchangers, steam generators, in terms of local corrosion: pitting, stress and intergranular corrosion, paying particular attention to welded joints area. The effect of steel chemical composition, microstructure, welding process and work environment was analyzed. The second part of the article presents the results of the...
-
Life Cycle Assessment of Analytical Protocols
PublicationLife cycle assessment is a relatively new tool for environmental management, which is becoming more and more important owing to the globalization of the world economy, where there is a need to develop standards in protecting the environment
-
Respiratory signals derived from capacitive electrocardiogram on the smart chair
PublicationCapacitive electrocardiogram (CECG) tends to deliver basic cardiac signals without need to use traditional glued electrodes. In the paper analysis of possibility if the ECG derived respiratory waveforms out of the CECG.
-
Advanced Monte Carlo simulator of the polarization-sensitive optical coherence tomography systems
PublicationSimulations of the optical coherence tomography (OCT) systems using the Monte Carlo method is a widely explored research area. However, there are several difficulties that need to be overcome in order to properly model the OCT imaging with the Monte Carlo algorithm. First of all, the temporal and the spatial coherence of the scattered light need to be considered, since OCT is based on the interference phenomenon. For the same reason,...
-
Effect of Laminar Pulsatile Fluid Flow on Separation of Volatile Organic Compounds from Aqueous Solution by a Hollow Fiber Membrane-Based Process
PublicationIn this study, a laminar pulsatile fluid flow was used for the separation of benzene, toluene, ethylbenzene, and xylene isomers (BTEX) from aqueous solutions. Polyether sulfone hollow fiber membrane has been applied to this process. The effects of BTEX concentration, and feed and extraction flow rates were examined. It was found that the application of the pulsatile fluid flow with...
-
Landscape protection - the challenge for sustainable planning
PublicationGrowing spatial chaos reminds us of the need for systematic, complex approaches related to environmental and landscape issues within different planning, organizational, operational, legal and political activities. It has been proved, that LVIA within EIA plays an important role in the enhancement of the spatial planning system, and that there is a need to use the potential of EIA/LVIA in spatial development and management. But...
-
Removal of VOCs from air and assessment of dominant species in a peat-perlite biotrickling filter
PublicationAir pollution has become a major concern because it is inevitably connected with the rapid development of both industrial and residential areas. Volatile organic compounds (VOCs) are emitted from various anthropogenic sources e.g. transportation, factories or landfills as well as recycling factories. It is problematic not only because of the direct impact on humans and environment but also from economy viewpoint as it increases...
-
Sustainable recovery of plant essential Nitrogen and Phosphorus from human urine using industrial coal fly ash
PublicationCoal-based thermal power plants play a pivotal role in meeting global energy demand. The amount of fly ash generated from these plants increases every year, and its successful use has posed a significant environmental risk in the last decade. In this study, coal fly ash was packed in a fixed-bed adsorption column to remove Urea–N from synthetic human urine. To assess the efficacy of fly ash in the removal of Nitrogen, various process...
-
Dynamic GPU power capping with online performance tracing for energy efficient GPU computing using DEPO tool
PublicationGPU accelerators have become essential to the recent advance in computational power of high- performance computing (HPC) systems. Current HPC systems’ reaching an approximately 20–30 mega-watt power demand has resulted in increasing CO2 emissions, energy costs and necessitate increasingly complex cooling systems. This is a very real challenge. To address this, new mechanisms of software power control could be employed. In this...
-
Photocatalytical degradation of toluene and cyclohexane using LED illumination
PublicationA sol-gel process followed by hydrothermal reaction was used to prepare coupled WO3-TiO2 photocatalysts with varying amounts of WO3 in respect to TiO2 (3 mol% and 5 mol% respectively). Additionally, photocatalysts have been subjected to different calcination temperatures of 400ºC and 800ºC, which allowed us to compare how these affect photodegradation efficiency. Photocatalysts were characterized under a scanning electron microscope,...
-
Biotrickling filtration of n-butanol vapors: process monitoring using electronic nose and artificial neural network
PublicationBiotrickling filtration is one of the techniques used to reduce odorants in the air. It is based on the aerobic degradation of pollutants by microorganisms located in the filter bed. The research presents the possibility of using the electronic nose prototype combined with artificial neural network for biofiltration process monitoring in terms of reduction in n-butanol concentration and odour intensity of treated air. The study...
-
Fabrication of Bi6Fe2Ti3O18 Ceramics by Mixed Oxide Method
PublicationIn the present study Bi6Fe2Ti3O18 (BFTO) ceramics has been fabricated by solid state reaction from the mixture of simple oxides viz. Bi2O3, TiO2 and Fe2O3. Stoichiometric mixture of the powders was thermally analyzed so parameters of the thermal treatment were determined. The EDS measurements have shown conservation of the chemical composition of the ceramic powder after calcination. Hot-pressing method was used for final densification...
-
Removal of organic matter and nitrogen in an horizontalsubsurface flow (HSSF) constructed wetland undertransient loads
PublicationA monitoring campaign in a horizontal subsurface flow constructed wetland under the influence of transient loads of flow-rate, organic matter, nitrogen and suspended solids showed an irregular removal of COD and TSS and lower both removal efficiencies and mass removal rates than the ones observed in other studies for similar operating conditions. This circumstance is associated to the presence of large amount of particulate organic...
-
Eksploatacyjne uszkodzenia stali austenitycznych w urządzeniach energetycznych
PublicationW artykule przedstawiono proces niszczenia stali austenitycznych stosowanych w urządzeniach energetycznych, takich jak wymienniki ciepła czy wytwornice pary, w warunkach korozji lokalnej: wżerowej, podosadowej, naprężeniowej i międzykrystalicznej, ze zwróceniem szczególnej uwagi na połączenia spawane. Analizowano wpływ składu chemicznego stali, mikrostruktury, procesu spawania i środowiska pracy. Przedstawiono wyniki badań metalograficznych...
-
Release and Transport of Toxic, Mobile Organic Compounds (Formaldehyde and Phenols) on an Arctic Glacier
PublicationAs a result of current deglaciation, the chemical cycles of many compounds, including toxic formaldehyde and phenols, are changing. However, the processes by which these chemicals are released have yet to be studied in situ. Here, we quantify fluxes of HCHO and phenols in a glacial catchment within one summer season, obtaining a net release from the glacier of 0.106 · 106 g formaldehyde and 0.255 · 106 g phenols, which can be interpreted...
-
MSIS sonar image segmentation method based on underwater viewshed analysis and high-density seabed model
PublicationHigh resolution images of Mechanically Scanned Imaging Sonars can bring detailed representation of underwater area if favorable conditions for acoustic signal to propagate are provided. However to properly asses underwater situation based solely on such data can be challenging for less than proficient interpreter. In this paper we propose a method to enhance interpretative potential of MSIS image by dividing it in to subareas depending...
-
THE METHOD OF ENERGY-EFFICIENCY INVESTIGATIONS OF THE NEWLY PRODUCED MARINE FUELS THROUGH AN APPLICATION OF THE LABORATORY DIESEL ENGINE
PublicationThe article deals with one of the scientific issue solved within frames of the research project financed by Voivodeship Fund for Environmental Protection and Water Management in Gdansk, namely, in particular, the method of energy investigations of the self-ignition engine in conditions of its supply with a non-standard (modified) marine fuel. The representative results of engine tests worked out on the especially built laboratory...
-
THE APPLICATION OF THE MECHANOCHEMICAL SYNTHESIS FOR THE PREPARATION OF ADVANCED CERAMICS BASED ON BARIUM TITANATE
PublicationIn the present study, the lead-free BaTi1-xZrxO3 (for x = 0, 0.05 and 0.15) ceramics were prepared by High-Energy Ball Milling and heat treatments. The performed X-ray, SEM and EDS measurements confirmed high purity, good quality and the expected quantitative composition of the obtained samples. The study of dielectric properties was performed by means of broadband dielectric spectroscopy at the frequency ranging from 0.1 Hz to...
-
Doing well by doing good — CSR in a global context
PublicationMotivation: Nowadays, there is a general understanding that stakeholders are crucial for the successful enterprise. There is also a need to think about Corporate Social Responsibility (CSR) in a global context. Never before corporations enjoyed so much power and authority. Corporations need to evolve, re-think their strategies and change their processes accordingly. However, as of now, there is no agreed way of measuring overall...
-
Scotish Philosophy and Vilnius Philosophers.
PublicationW pracy przedstawiono wpływ filozofii szkockiej (Th. Reid, D. Steward) na filozofów polskich związanych z Uniwersytetem Wileńskim (Anioł Dowgird, Jan Śniadecki, Michał Wiśniewski, Krystyn Lach-Szyrma).
-
Modification of Titanium (IV) Dioxide with Small Silver Nanoparticles: Application in Photocatalysis
PublicationThe surface of commercial TiO2 compounds (P25 and ST01) has been modified with Ag nanoparticles induced by radiolysis. On P25, the Ag nanoclusters are very small (1−2 nm) and homogeneous in size while on ST01, two populations of nanoparticles are obtained, small nanoparticles (1−2 nm) and larger ones (mean diameter 7 to 12 nm depending on the silver loading). The photocatalytic properties of Ag-modified TiO2 have been studied for...
-
Models of Information Systems Integration in CompaniesW : Information Systems Architecture and Technology : IT Models in Management Process
PublicationThis work indicates the need for supporting IT organizations with incident and change management IT tools. The work presents tche characteristics of a computer system for the comprehensive management of projects, wich can be used to resolve the issues of version management, releases and incidents.
-
Coarse-grained simulation - an efficient approach for studying motions of large proteins
PublicationOne of the most important challenges in performing Molecular Dynamics (MD) simulations of large protein complexes is to accommodate the model accuracy and the simulation timescale. Hitherto, for the most relevant dynamics of protein aggregates in an explicit aqueous environment, the timescale reachable for the all-atoms simulations is of hundreds of nanoseconds. This range is four to six orders of magnitude smaller than processes...
-
Computed aided system for separation and classification of the abnormal erythrocytes in human blood
PublicationThe human peripheral blood consists of cells (red cells, white cells, and platelets) suspended in plasma. In the following research the team assessed an influence of nanodiamond particles on blood elements over various periods of time. The material used in the study consisted of samples taken from ten healthy humans of various age, different blood types and both sexes. The markings were leaded by adding to the blood unmodified...
-
Quantitative assessment of the main antioxidant compounds, antioxidant activities and FTIR spectra from commonly consumed fruits, compared to standard kiwi fruit
PublicationBioactive compounds (polyphenols and ascorbic acid) and dietary fibers, and related antioxidant activities of commonly consumed apples, bananas, peaches, pears, blond and red grapefruits, pomelos, oranges, lemons, red plums, white grapes, mango, persimmon and strawberries grown in the same geographical and climatic conditions were compared with standard kiwi fruit. The presence of polyphenols was studied by Fourier transform infrared...
-
A Finer Point on Vision
PublicationAs an IES Member, I look forward to each issue of LD+A and read them with great interest as they are often very informative. To my surprise, the Research article (May 2019, p. 76) has an error which should be corrected.