Search
Filters
total: 1490
filtered: 1229
displaying 1000 best results Help
Search results for: PREFERENCJE DWUDZIESTOLATKÓW
-
Hierarchical dissolved oxygen control for activated sludge processes
PublicationA hierarchical controller for tracking the dissolved oxygen reference trajectory in activated sludge processes is proposed and investigated. The removal of nitrogen and phosphorous from wastewater is considered. Typically, an aeration system itself is a complicated hybrid nonlinear dynamical system with faster dynamics compared to the internal dynamics of the dissolved oxygen in a biological reactor. It is a common approach to...
-
Temperature influence on tyre/road noise of selected tyres
PublicationAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Low-cost data-driven modelling of microwave components using domain confinement and PCA-based dimensionality reduction
PublicationFast data-driven surrogate models can be employed as replacements of computationally demanding full-wave electromagnetic simulations to facilitate the microwave design procedures. Unfortunately, practical application of surrogate modelling is often hindered by the curse of dimensionality and/or considerable nonlinearity of the component characteristics. This paper proposes a simple yet reliable approach to cost-efficient modelling...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Description of the Dataset Rhetoric at School – a Selection of the Syllabi from the Academic Gymnasium in Gdańsk – Transcription and Photographs
PublicationThe research dataset described in the article was based on photographs and transcription of a textual record from Latin syllabi for classes at the Gdańsk Academic Gymnasium. The syllabi concern the years 1645/1648/1652/1653. The original document is held in the collection of the Gdańsk Library of the Polish Academy of Sciences [reference number: Ma 3920 8o]. The collected research material can be used for studying the practical...
-
Niepewność wyniku analizy - sposób obliczania
PublicationW pracy przedstawiono sposób obliczania niepewności wyniku analizy zalecany przez EURACHEM. Zamieszczono także podstawowe terminy i definicje, które są stosowane przy konsultowaniu budżetu niepewności i obliczaniu niepewności całkowitej. Praca powstała na podstawie doświadczeń autora w trakcie 2 letniego stażu podoktorskiego, odbytego w Institute for Reference Materials and Measurements w Geel (Belgia), jednym z laboratoriów Komisji...
-
Guitar String Sound Retrieved from Moving Pixels
PublicationThe aim of this study was to develop a method of visual recording and analyzing the vibrations of guitar strings using high-speed cameras and dedicated video processing algorithms. The recording of a plucked string reveals the way in which the deformations propagate, composing the standing and travelling wave. The paper compares the results for a few selected models of classical and acoustic guitars, and it involves processing...
-
Separation of Volatile Oxygen-containing Organic Compounds by Gas Chromatography - selectivity comparison of different polarity stationary phases
PublicationThis paper present a results of the separation of 36 reference compounds belonging to the group of Volatile Oxygen-Containing Organic Compounds (OVOCs) using capillary gas chromatography with flame ionization detector (GC-FID) and three stationary phases of different polarity. A selectivity has been studied regarding to OVOCs and n -alkanes. The most useful for the separation of the group OVOCs is a polar ionic liquid stationary...
-
MEASUREMENT O F HEALTHCARE SYSTEM EFFICIENCY IN OECD COUNTRIES
PublicationIncreased spending on healthcare systems in many countries tends to attract attention to their efficiency. The aim of this paper is to evaluate the efficiency of healthcare systems in the OECD countries and indicate causes of inefficiency by applying Data Envelopment Analysis (DEA) and using additive and super-efficiency models. The homogeneity of the sample is assessed and outliers are excluded. A ranking is established on the...
-
Geometry of cycling track
PublicationThe paper describes the problems related to shaping of the geometry of the cycling track. The method of selection of the angle at the track curve is presented. Issues related to the selection of the appropriate transition curve and the superelevation section along the transition curve are presented. Reference to the recommendations presented in the literature and scientific papers has been made. Special attention...
-
The preferable ways of decision-making in IT teams
PublicationSoftware development team collaboration requires various decisions regarding essential aspects of a project’s progress. General and particular decision-making models are considered, and their main aspects such as team types, problem solving categories, and decision-making ways are analyzed. The research concerns representative groups of IT specialists and their preferences in decision-making are investigated. Four possible cases were...
-
Porównanie algorytmów lokalizacji wewnątrzbudynkowej bazujących na radiowych pomiarach odległości
PublicationNiniejszy artykuł ma na celu ocenę wybranych algorytmów estymacji położenia, które mogą być zastosowane w systemach lokalizacji w środowiskach zamkniętych. Przedstawiono pięć algorytmów bazujących na pomiarach odległości. Następnie porównano ich dokładności estymacji w warunkach statycznych oraz dla scenariusza dynamicznego przy ustalonym rozmieszczeniu trzech stacji referencyjnych. Dokonano również porównania czasu estymacji pojedynczej...
-
The impact of addition of olive oil on thermal degradation of refined rapeseed oil
PublicationFats are an important component of the everyday diet and have a significant impact on the proper functioning of human organism. However, during the process of frying chemical transformations take place in the oil; hence fats characterised by high oxidative stability should be given preference. The aim of this work was to determine the quality of rapeseed oil, blended oil, and refined olive oil, all sourced from the domestic market....
-
Metody usuwania zakłóceń podczas pomiarów polowych widm Ramana
PublicationW pracy zostały scharakteryzowane źródła zakłóceń występujące podczas pomiarów widm Ramana w warunkach polowych. Zaprezentowano wpływ czasu integracji na jakość rejestrowanych widm w przypadkach, gdy szumy własne spektrometru mają składową typu 1/f, dominującą w zakresie małych częstotliwości. Przedstawiono także wyniki uzyskane podczas pomiarów z detekcją synchroniczną, stosowaną w przenośnych spektrometrach Ramana, w pomiarach...
-
A new approach to active noise and vibration control - [Part II: unknown frequency case]
PublicationThis paper presents a new approach to rejection of complex-valued sinusoidal disturbances acting at the output of a discrete-time stable linear plant with unknown and possibly timevarying dynamics. It is assumed that both the instantaneous frequency of the sinusoidal disturbance and its amplitude may be slowly varying with time and that the output signal is contaminated with wideband measurement noise. It is not assumed that a...
-
Evaluation of respiration rate and pattern using a portable thermal camera
PublicationThe goal of this paper was to analyze the accuracy of the proposed method for the evaluation of respiration rate and respiration rhythm patterns (e.g. inspiration slope) using the portable and mobile thermal camera module that could be a part of smart glasses. Parameters were analyzed for 12 volunteers in two experiments, when subjects speak and do not speak. The pressure, chest belt was used as a reference measurement method....
-
The silver layers in fiber-optic sensors
PublicationIn this paper a method of application of the silver layers on the surface of an optical fiber was proposed. The optical properties and surface quality of the silver layer was examined by optical microscopy. The reflection and transmission of the sample were investigated. To evaluate the silver mirror it was placed in a fiber optic Fabry-Perot interferometer and the quality of the spectra was analyzed. The commercial mirror was...
-
A Review of Antennas for Indoor Positioning Systems
PublicationThis paper provides a review of antennas applied for indoor positioning or localization systems. The desired requirements of thoseantennas when integrated in anchor nodes (reference nodes) are discussed, according to different localization techniques and theirperformance. The described antennas will be subdivided into the following sections according to the nature of measurements:received signal strength (RSS), time of flight (ToF),...
-
The change of mechanical properties of selected wood species after drying process under various conditions
PublicationThe result of mechanical properties change of selected wood species after drying process under various parameters are presented. The global elasticity modulus and bending strength for steam dried, air-steam mixture dried and air dried samples as reference were measured. It allowed to reveal the effect of wood stream, air-steam mixture and their temperature on mechanical properties of wood. It has been recognized that steam and...
-
Mobile application technology in levelling
PublicationThe topic of this article is the use of mobile application technology in geodetic measurements with an emphasis on levelling. Reference points were registered as data from levelling benchmarks, performed with a traditional dumpy level. The created application allowed the recording of measurements on location, sending them to a remote server for processing and preparing a report to be saved in a database. The project was to decrease...
-
The properties of reduced Ge-Sb-O glasses for thermoelectric devices
PublicationThe structural and electrical properties of germanium-antimonate glasses after heat treatment in hydrogen have been determined. In the case of 50GeO2-50Sb2O3 glass reduced at 340°C even for less than 1 hour a continuous layer of antimony granules is formed and its electrical properties determine the surface conductivity of the reduced sample. The bulk electrical conductivity at 100°C of this sample was determined as 1000 Scm-1...
-
Load test of new European record holder in span length among extradosed type bridges
PublicationThe article presents acceptance load tests of a newly built extradosed MS-3 bridge located along the national road DK-16 near Ostróda (Poland). The structure features significant dimension in European reference scale. It is a new record holder in span length regarding this distinct bridge category. Its length ranges 206 m. Static and dynamic load tests were performed here. The program was extended by entire structural laser scanning...
-
Efektywność procesu kształcenia w wyższych szkołach zawodowych w 2012 roku
PublicationCelem artykułu jest pomiar efektywności działalności dydaktycznej oraz określenie rankingu efektywności wyższych szkół zawodowych w 2012 roku. Analiza obejmuje 25 wyższych szkół zawodowych nadzorowanych przez Ministerstwo Nauki i Szkolnictwa Wyższego. Do obliczenia efektywności wykorzystano nieparametryczną metodę DEA. Za rezultaty przyjęto liczbę absolwentów oraz wskaźnik oceny preferencji pracodawców, w przypadku nakładów...
-
Analityczny hierarchiczny proces decyzyjny. Nierozmyte i rozmyte porównania parami. Seria: Badania systemowe. T. 29
PublicationAnalityczny hierarchiczny proces decyzyjny należy do klasy metod wielokryterialnych podejmowania decyzji. Polega na wyborze najlepszego wariantu, z niezbyt dużej ich liczby, z uwzględnieniem wielu kryteriów. Metoda oparta jest na porównaniach parami wariantów, dokonywanych przez ekspertów, w oparciu o subiektywną preferencję jednego wariantu nad drugim. Wynikiem porównania może być ocena rozmyta i nierozmyta. Na podstawie...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublicationTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
Experimental study of the impact of notches and holes made in the front edge of adherends on the properties of static and fatigue strength of adhesive joints
PublicationThe paper presents the results of experimental studies aimed at determining the effect of holes and notches at the front edge of adherends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets joined with Araldite 2014-2 epoxy adhesive were tested. Comparative tests of static strength in the shear test as well as high-cycle fatigue strength tests were carried out. Joints with three holes with a diameter...
-
An optimized dissolved oxygen concentration control in SBR with the use of adaptive and predictive control schemes
PublicationThis paper addresses the problem of optimizing control of the aeration process in a water resource recovery facility (WRRF) using sequencing batch reactor (SBR), one that affects the efficiency of wastewater treatment by stimulating metabolic reactions of microorganisms through dissolved oxygen (DO) level control, and accounts for the predominant part of operating costs. Two independent approaches to DO control algorithm design...
-
Core loss resistance impact on sensorless speed control of an induction motor using hybrid adaptive sliding mode observer
PublicationInduction motors (IMs) experience power losses when a portion of the input power is converted to heat instead of driving the load. The combined effect of copper losses, core losses, and mechanical losses results in IM power losses. Unfortunately, the core losses in the motor, which have a considerable impact on its energy efficiency, are not taken into account by the generally employed dynamic model in the majority of the studies. Due...
-
Field Calibration of Low-Cost Particulate Matter Sensors Using Artificial Neural Networks and Affine Response Correction
PublicationDue to detrimental effects of atmospheric particulate matter (PM), its accurate monitoring is of paramount importance, especially in densely populated urban areas. However, precise measurement of PM levels requires expensive and sophisticated equipment. Although low-cost alternatives are gaining popularity, their reliability is questionable, attributed to sensitivity to environmental conditions, inherent instability, and manufacturing...
-
Arching of railway turnouts by analytical design method
PublicationThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Application of the Electronic Nose Technique to Differentiation between Model Mixtures with COPD Markers
PublicationABSTRACT The paper presents the potential of an electronic nose technique in the field of fast diagnostics of patients suspected of Chronic Obstructive Pulmonary Disease (COPD). The investigations were performed using a simple electronic nose prototype equipped with a set of six semiconductor sensors manufactured by FIGARO Co. They were aimed at verification of a possibility of differentiation between model reference mixtures with...
-
The Central European GNSS Research Network (CEGRN) dataset
PublicationThe Central European GNSS Research Network (CEGRN) collects GNSS data since 1994 from contributors which today include 42 Institutions in 33 Countries. CEGRN returns a dataset of coordinates and velocities computed according to international standards and the most recent processing procedures and recommendations. We provide a dataset of 1229 positions and velocities resulting from 3 or more repetitions of coordinate measurements...
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublicationIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
Analytical design method for widening the intertrack space
PublicationThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Reliable Surrogate Modeling of Antenna Input Characteristics by Means of Domain Confinement and Principal Components
PublicationA reliable design of contemporary antenna structures necessarily involves full-wave electromagnetic (EM) analysis which is the only tool capable of accounting, for example, for element coupling or the effects of connectors. As EM simulations tend to be CPU-intensive, surrogate modeling allows for relieving the computational overhead of design tasks that require numerous analyses, for example, parametric optimization or uncertainty...
-
Numerical analysis of pile installation effects in cohesive soils
PublicationIn this thesis the empirical equation for radial effective stress calculation after displacement pile installation and following consolidation phase has been proposed. The equation is based on the numerical studies performed with Updated Lagrangian, Arbitrary Lagrangian-Eulerian and Coupled Eulerian-Lagrangian formulations as well as the calibration procedure with database containing world-wide 30 pile static loading tests in cohesive...
-
Golden artefacts, resin figurines, body adhesives and tomb sediments from the pre-Columbian burial site El Caño (Gran Coclé, Panamá): tracing organic contents using molecular archaeometry
PublicationThis research aimed to determine the origin of organic residues from funerary contexts in the El Ca~no settlement (Gran Cocl�e area, Panam�a, Central America) by means of multiple molecular probing techniques (GC-MS of organic solvent extracts and pyrolysis-GC-MS, THM-GC-MS and FTIR of solid samples). The samples include particles of precious resin figurines, fillings of golden objects, tomb sediments, plant exudates from extant...
-
TDOA versus ATDOA for wide area multilateration system
PublicationThis paper outlines a new method of a location service (LCS) in the asynchronous wireless networks (AWNs) where the nodes (base stations) operate asynchronously in relation to one another. This method, called asynchronous time difference of arrival (ATDOA), enables the calculation of the position of the mobile object (MO) through the measurements taken by a set of non-synchronized fixed nodes and is based on the measurement of...
-
Analysis of human behavioral patterns
PublicationWidespread usage of Internet and mobile devices entailed growing requirements concerning security which in turn brought about development of biometric methods. However, a specially designed biometric system may infer more about users than just verifying their identity. Proper analysis of users’ characteristics may also tell much about their skills, preferences, feelings. This chapter presents biometric methods applied in several...
-
The power of silence? opinion contagion and the surprise of the polish 2005 parlamentary and presidential elections
PublicationThis paper investigates opinion contagion in collective behaviour using threshold model (Granovetter (1978), Krassa(1988)). The theoretical background is the spiral of silence concept developed by Noelle-Neumann (1974), arguing that people only assert their opinions if they perceive a minimal support from a relevant proportion of others. We apply the model to explain the dispersion between pre-elections preferences and the final...
-
DECISION - MAKING IN VIRTUAL SOFTWARE TEAMS USING CLOUD PLATFORMS
PublicationSoftware development projects are usually realized by traditional or virtual IT teams using computing clouds. Team collaboration requires decision - making regarding essential aspects of a project progress. The article concerns methods of decision – making process in the case of traditional and virtual teams’ work. The research results conducted in a group of IT specialists are presented, and to analyze their preferences in decision-making...
-
Augmenting digital documents with negotiation capability
PublicationActive digital documents are not only capable of performing various operations using their internal functionality and external services, accessible in the environment in which they operate, but can also migrate on their own over a network of mobile devices that provide dynamically changing execution contexts. They may imply conflicts between preferences of the active document and the device the former wishes to execute on. In the...
-
Superkomputery do wspomagania procesów gospodarczych ze szczególnym uwzględnieniem sektora bankowego
PublicationW artykule omówiono wykorzystanie superkomputerów do wspomagania procesów gospodarczych ze szczególnym uwzględnieniem sektora bankowego. Odniesiono się do wybranych projektów wspierających rozwój gospodarczy w oparciu o superkomputery. W szczególności zaproponowano zastosowanie HPC do implementacji wybranych metod sztucznej inteligencji w bankowości, w tym oceny ryzyka wybranych przedsięwzięć. Zaproponowane podejście umożliwia...
-
ZASTOSOWANIE FILTRACJI CZĄSTECZKOWEJ DO ESTYMACJI POŁOŻENIA W SYSTEMIE LOKALIZACYJNYM UWB
PublicationNiniejszy artykuł dotyczy kwestii poprawy dokładności estymacji położenia w systemie lokalizacji wewnątrzbudynkowej, bazującym na radiowych pomiarach odległości realizowanych przez modemy UWB. Proponuje się zastosowanie metody filtracji cząsteczkowej do zmniejszenia błędu wyznaczania pozycji obiektu przy braku bezpośredniej widoczności ze stacją referencyjną. W artykule opisano algorytm filtru cząsteczkowego, jego przykładową implementację...
-
Proces zmiany sprzedawcy energii elektrycznej w Polsce dla odbiorcy w gospodarstwie domowym
PublicationW publikacji przedstawiono proces zmiany sprzedawcy energii elektrycznej dla odbiorcy w gospodarstwie domowym, prowadzony w detalicznym segmencie rynku energii. Szczególny nacisk położono na proces bazujący na generalnej umowie dystrybucji dla usługi kompleksowej. Odniesiono się do wszystkich, istotnych regulacji mających zastosowanie do poruszanych kwestii, ze szczególnym uwzględnieniem zapisów instrukcji ruchu i eksploatacji...
-
Bodybuilders and high-level meat consumers’ behavior towards rabbit, beef, chicken, turkey, and lamb meat: A comparative review
PublicationIn bodybuilders’ diets, protein plays a crucial role in supporting muscle growth and repairing damaged muscle tissue. These individuals meet their protein needs by combining dietary sources with supplements. Animal-based proteins are often preferred over plant-based proteins because they are believed to better support muscle protein synthesis. This review explores the meat consumption patterns of bodybuilders and high-level meat...
-
CLASSIFICATION OF RESTRAINTS IN THE OPTIMIZATION PROBLEM OF A COLD-FORMED PROFILE
PublicationThis work describes the restraints in the optimization problem. This is an important and complicated issue because it requires taking into account a vast range of information related to the design and production. In order to describe the relations of a specific optimization problem, it is essential to adopt appropriate criteria and to collect information on all kinds of restraints, i.e. boundary conditions. The following paper...
-
A Method and Device for 3D Recognition of Cutting Edge Micro Geometry
PublicationA very useful method was successfully applied in the investigation of tools for machining wood and wood based composites. It allows scanning of the cutting edge micro geometry in three dimensions and reproducing it in a virtual space as a 3D surface. The application of the method opens new possibilities of studying tool wear by scanning, including the calculation of volume loss and other analysis of tool wedge geometry along and...
-
Effectiveness of the robust PSS design
PublicationThe paper discusses optimal PSS of synchronous generator synthesis. The optimal controller is an Hinf controller, what means that minimises Hinf norm of transfer function between the exogenous signals such as reference inputs and disturbances, and the error signals which are to be minimised to meet the control objective. The dynamic properties of the plant are shaped by choosing appropriate weighting function applied to the plant...
-
Electrodes array for contactless ECG measurement of a bathing person - a sensitivity analysis
PublicationAn applicability of a remote (contactless) electrocardiogram (ECG) measurements in a bathtub is presented in the paper. Possibility of ECG measurements in shallowly filled tube with a water was examined. A bathing person was, both, sitting and lying during experiments performed. The problem became non-trivial when the bathing person was moving in reference to a fixed set of electrodes and located at the longer walls of the bathtub....