Filtry
wszystkich: 1130
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: industry analysis, five forces, six forces
-
SPECTRAL RESPONSE OF STATIONARY JACK-UP PLATFORMS LOADED BY SEA WAVES AND WIND USING PERTURBATION METHOD
PublikacjaThe paper addresses non-linear vibrations of offshore jack-up drilling platforms loaded by sea waves and wind in their stationary condition using the perturbation method. Non-linearity of dynamic equations of motion for fixed offshore platforms yields from two factors. The first is load excitation generating non-linear velocity coupling in a dynamic system. This coupling is inherent in the modified Morison equation, involving the...
-
Determining the optimal filling of the surface with a linker with Universal Force Field and Reax Force Field
Dane BadawczeThe DataSet contains the atomic slabs of diamond surfaces with ATP molecules in water. The calculated data includes different sized surfaces from 90 Angstrom^2 to 691 Angstrom^2. Structures were relaxed using the Reax Force Field method with the Limited Memory Broyden–Fletcher–Goldfarb–Shanno algorithm. Structures were calculated with a convergence...
-
Smart Decisional DNA Technology to Enhance Industry 4.0 Environment in Conjunction with Conventional Manufacturing
PublikacjaKnowledge-based support has become an indispensable part not only to the traditional manufacturing set-ups but also to the new fast-emerging Industry 4.0 scenario. In this regard, successful research has been performed and extensively reported to develop Decisional DNA based knowledge representation models of engineering object and engineering process called Virtual engineering object (VEO), Virtual engineering process (VEP) and...
-
Adaptive dynamic control allocation for over-actuated dynamic positioning system based on backstepping method in case of thruster faults
PublikacjaThe objective of the research considered in this paper is dynamic positioning of a nonlinear over-actuated marine vessel in the presence of limited information about thruster forces. First, the adaptive backstepping method is used to estimate the input matrix which will compensate partial loss of actuator effectiveness in the presence of actuator dynamics. Then, the adaptive commanded virtual forces and moment are allocated into...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
Verification of punching shear outside the shear cap by the direct method
PublikacjaThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
SAWING PROCESS AS A NEW ALTERNATIVE WAY OF DETERMINING SOME WOOD PROPERTIES
PublikacjaCutting forces (power) could be considered from a point of view of modern fracture mechanics. The developed cutting model, derived from fracture mechanics, includes work of separation (fracture toughness) in addition to plasticity and friction, and also dullness of the cutting edge described by the cutting edge radius. Moreover, forecasting of the shear plane angle for the cutting models, broaden possibilities of energetic effects...
-
Development and validation of lumbar spine finite element model
PublikacjaThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research. A FE model of the 50th percentile adult male (AM) Total Human Model for Safety...
-
Izabela Mironowicz dr hab. inż. arch.
Osoby -
Expert systems in assessing the construction process safety taking account of the risk of disturbances
PublikacjaThe objective of the paper is to present the issue of safety manage-ment during the construction process. Threats in the form of disturb-ances may occur in the preparatory phase, during the execution of the construction project and also during its operational use. The arti-cle presents the concept of applying the methodology based, among others, on Learning Bayesian Networks, Artificial Neural Networks and Support Vector Machine,...
-
Vibration testing in buildings and safety of their operation
PublikacjaThe paper presents the issue of vibrations in residential buildings located near roads. It describes the measurement methodology and criteria for assessing the impact of vibrations generated by passing trucks. The article specifies a method to establish the impact on the operation of the examined facilities and it promotes the idea of employing a Bayesian network to determine probabilistically the level of risk to single-family...
-
Secured wired BPL voice transmission system
PublikacjaDesigning a secured voice transmission system is not a trivial task. Wired media, thanks to their reliability and resistance to mechanical damage, seem an ideal solution. The BPL (Broadband over Power Line) cable is resistant to electricity stoppage and partial damage of phase conductors, ensuring continuity of transmission in case of an emergency. It seems an appropriate tool for delivering critical data, mostly clear and understandable...
-
Magneto-thermal convection of low concentration nanofluids
PublikacjaThe main aim of this paper was to analyze possible utilization of the low concentration nanofluids and the magnetic field to enhance heat transfer. The studied fluids were based on water with an addition of copper particles (40-60 nm diameter). They belonged to the diamagnetic group of materials. As a first attempt to stated target the analysis of enclosure placed in the maximal value of square magnetic induction gradient was carried...
-
FEM approach to estimate the behaviour of biocomposite metal-surface coating system
PublikacjaA three dimensional (3D) model of biocomposite metal-surface coating system, which is influenced byknown external forces, is proposed. This model consists of the metallic substrate (Ti6Al4V) and thehydroxyapatite (HA) coating. Using FEM (finite element method), strain-stress maps of model weregenerated for investigating relations between the extreme stress of HA coating and the magnitude ofexternal force and the thickness of the...
-
Behaviour of Colliding Multi-Storey Buildings under Earthquake Excitation Considering Soil-Structure Interaction
PublikacjaThis paper investigates the coupled effect of the supporting soil flexibility and pounding between neighbouring, insufficiently separated buildings under earthquake excitation. Two adjacent three-storey structures, modelled as inelastic lumped mass systems with different structural characteristics, have been considered in the study. The models have been excited using the time history of the Kobe earthquake of 1995. A nonlinear...
-
Characterization of Arctic Driftwood as Naturally Modified Material. Part 1: Machinability
PublikacjaArctic driftwood has reached the coast of Iceland for centuries. This material was used by the inhabitants of the island as a building material for houses, boats, churches and pasture fences. Nowadays, the driftwood is used in the furniture industry, for the finishing of internal and external walls of buildings and also by artists. The properties of driftwood differ to that of original resource due the long-term effects of exposure...
-
AN INNOVATIVE APPROACH TO PREDICTION ENERGETIC EFFECTS OF WOOD CUTTING PROCESS WITH CIRCULAR-SAW BLADES
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. The aim of the paper is to present a new calculating model using the application of modern fracture mechanics and to compare cutting parameters of native beech, Bendywood...
-
An influence of the ship's block coefficient implementation on the evaluation of it's hull girder bending
PublikacjaAn influence of the three different ways of implementation ship's block coefficient δ (three geometrical models) on the stresses due to wave bending moment have been investigated. Two models have been applied and compared: beam one (description of the shape usingparameters) and FEM shell model (direct representation of the shape). The outcomes have been compared to Polish Register of Shipping (PRS) rules. The results show that...
-
Diagnostics and monitoring of the longest span extradosed bridge in Europe
PublikacjaThe article presents complex diagnostic procedures applied for the purpose of behavior analysis of the extradosed bridge with the longest span in Europe that was built in 2018 in Poland. The system of health monitoring was used to: register internal forces in temporary supports, monitor concrete bonding, perform in situ diagnostics and operation tests. The bridge is a continuous four-span structure with spans theoretical lengths...
-
Analiza numeryczna i analityczna przekrycia w kształcie powłoki synklastycznej o podstawie kwadratowej
PublikacjaW pracy poruszono problem obliczania przekrycia żelbetowego w kształcie powłoki synklastycznej ściętej o podstawie kwadratowej. Przedstawiono obliczenia analityczne i numeryczne sił w powłoce. Powłoka jest poddana działaniu głównie sił ściskających, co jest korzystne dla tego typu konstrukcji. W strefie brzegowej i podporowej konieczne jest wymiarowanie na mimośrodowe ściskanie i rozciąganie z uwagi na znaczący wzrost momentów...
-
New generation of the satellite hydraulic pumps
PublikacjaHydraulic satellite machines are known and produced in many versions, recognizable by the number of humps on their inner rotor and external gear, and therefore by the number of cooperating gears (satellites). All known shapes were however designed on the base of preliminary assumption that rotor’s and external gear’s pitch lines are formed by merging arcs, tangent to each other in the. This assumption makes calculations easier,...
-
On nonlinear dilatational strain gradient elasticity
PublikacjaWe call nonlinear dilatational strain gradient elasticity the theory in which the specific class of dilatational second gradient continua is considered: those whose deformation energy depends, in an objective way, on the gradient of placement and on the gradient of the determinant of the gradient of placement. It is an interesting particular case of complete Toupin–Mindlin nonlinear strain gradient elasticity: indeed, in it, the...
-
Comparative analysis of balancing of V6 engines with common- and split-pin crankshafts
PublikacjaAn analysis of balancing of V6 engines equipped with split-pin crankshafts with any cylinder bank angle based on the mathematical relations derived in the paper was carried out. A comparison of the quality of their balancing with engines equipped with common-pin crankshafts was also carried out. The bank angle ranges beneficial for balancing of moments of inertia forces in reciprocating motion were determined. A mathematical relation...
-
Dynamic analysis of lightweight structure of the Viaduct Millau in France subjected to the wind fluctuations described by Karman’s and Davenport’s spectrum
PublikacjaThe article presents numerical simulations for wind impact modelling on the Millau Viaduct structure in France performed with two independent spectrum generation methods. The viaduct's construction in affected by strong forces, as it is situated in the Tarn river's valley. Thus, the loading coming from the wind cannot be modelled, the way it is in case of simple structures as static loading, but as a loading in a form of a spectrum...
-
Theoretical analysis of the cable-stayed bridge over brda river in Bydgoszcz
PublikacjaThe topic of this article is the numerical analysis carried out for the cable-stayed tram (road) bridge over Brda river in Bydgoszcz. The goal of numerical studies was the verification of project assumptions and construction solutions elaborated by the autonomous team. The bridge calculations were conducted on three independent FEM models The internal forces and the elements effort under different loading schemes were examined....
-
ADAPTIVE BACKSTEPPING TRACKING CONTROL FOR OVER-ACTUATED DP MARINE VESSEL WITH INERTIA UNCERTAINTIES
PublikacjaDesigning a tracking control system for an over-actuated dynamic positioning marine vessel in the case of insufficient information on environmental disturbances, hydrodynamic damping, Coriolis forces and vessel inertia characteristics is considered. The designed adaptive MIMO backstepping control law with control allocation is based on Lyapunov control theory for cascaded systems to guarantee stabilization of the marine vessel...
-
A method to determine the tightening sequence for standing rigging of a mast
PublikacjaThe article proposes an alternative method to determine the sequence of generation of pre-tension forces in standing rigging of a mast. The proposed approach has been verified on both a virtual simulation experiment and laboratory tests. In this method, the desired tension values are obtained using the influence matrix which allows to calculate the effect of tension change in an individual rope on the tension distribution in the...
-
CUTTING POWER FORECASTING WHILE WOOD SAWING: FRACTURE MECHANICS APPROACH AND AXELSSON’S MODEL COMPARISON
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Another way is to forecast cutting power consumption on...
-
Influence of external climate on natural ventilation performance in buildings
PublikacjaNatural ventilation is driven by either buoyancy forces or wind pressure forces or their combinations that inherit stochastic variation into ventilation rates [ CITATION Hun99 \l 1045 ]. We now that these factors have influence on air flow speed and thermal comfort inside building. This work examines the relationship between external climate and natural ventilation including thermal comfort. The work tries in the first instance...
-
The influence of screw configuration and screw speed of co-rotating twin screw extruder on the properties of products obtained by thermomechanical reclaiming of ground tire rubber
PublikacjaThe results of our investigations on the process of continuous thermomechanical reclaiming of ground tire rubber (GTR) carried out using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear forces. The influence of screw configuration and screw speed on breaking of chemical crosslink bonds contained in ground tire...
-
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublikacjaThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
Zwodzona kładka dla pieszych na wyspę Ołowiankę w Gdańsku - analizy dynamiczne z wykorzystaniem modelu numerycznego MES
PublikacjaW artykule przedstawiono projekt zwodzonej kładki dla pieszych przez rzekę Motławę na wyspę Ołowiankę w Gdańsku. Omówiono jej konstrukcję oraz obliczenia numeryczne sprawdzające wytrzymałość, ugięcie i siły w siłownikach podczas zwodzenia. Dokonano również oceny poziomu komfortu i nośności konstrukcji pod wpływem działania obciążeń dynamicznych generowanych przez pieszych.
-
Investigation method of large-volume tire with mobile test rig
PublikacjaThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
Influence of steel brackets supporting crane runway girders structure on the stress distribution in the brackets
PublikacjaThe paper presents a numerical analysis of steel brackets supporting a double-span crane runway girders. The purpose of the study was to assess the new structural solution based on the stress distribution in the brackets. In order to simplify the connection, the bottom flange of the crane runway girder is based directly on the upper flange of the bracket. As a result, the support reaction is no longer applied in the plane of the...
-
PA32 aluminum alloy - tensile properties
Dane BadawczeIn addition to steel, aluminium alloys are the main building material used in the shipbuilding industry. Due to its undoubted advantages, such as low density (nearly three times lower than in the case of steel for shipbuilding) and high corrosion resistance, it is often used for hulls of yachts and small vessels as well as superstructures. For safety...
-
The Influence of Shear Deformation in analysis of plane frames
PublikacjaThe focus of the paper is to investigate the influence of shear deformation effect on the distribution of internal forces and frame deformation. To estimate shear deformation effect, the Timoshenko beam theory and the concept of shear deformation coefficients are used. Analysis of example frames gives the possibility to evaluate what have the most impact on size of shear deformation and in which type of frames the shear deformation...
-
Wstępny plan badań węzła z mimośrodem dodatnim w kratownicy z kształtowników o przekrojach poprzecznych otwartych. -(Autorka otrzymała wyróżnienie za tą publikację)
PublikacjaW celu określenia wpływu mimośrodowego przecinania się prętów w kratownicy z kształtowników giętych na zimno, o przekrojach poprzecznych otwartych na nośność i stateczność węzłów dźwigarów kratowych, opracowano model badawczy oraz przeprowadzono wstępną analizę numeryczną przedmiotowego węzła, w programie Marc Mentat. Uzyskane wyniki wskazują na potrzebę uzupełnienia obciążenia o parę sił poziomych w modelu badawczym.
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublikacjaIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
Orthotropic membrane as a mechanical model of surgical implant in abdominal hernia repair
PublikacjaEven though the incisional hernia repair surgery is a well known procedure, mechanical properties of the tissue-implant system are unknown so the implantation of the repairing mesh is quite intuitive and, recurrences of the illness still take place. The main objective of the study is to define an operated hernia model that can be used for surgery planning and the assessment of the repair persistence. The load applied to the structure...
-
Projektowanie zbiornika na nieczystości ciekłe
PublikacjaW artykule przedstawiono proces projektowania zbiornika podziemnego na nieczystości ciekłe o pojemności ok. 10 m3 posadowionego na gruntach niespoistych (sypkich). Porównano wartości sił wewnętrznych w przypadku skrajnie różnych warunków gruntowych: piasku drobnego o ID = 0,2 oraz żwiru o I D = 0,7. Dodatkowo przeanalizowano wpływ modelu obliczeniowego podłoża na wyniki sił wewnętrznych. Opisano procedurę normową pozwalającą na...
-
Numerical modeling and experimental validation of full-scale segment to support design of novel GFRP footbridge
PublikacjaThe paper contains analysis of full-scaled three meters long segment of a novel composite footbridge. Both numerical modeling and experimental validation were performed. Analyzed object is a shell type sandwich channel-like structure made of composite sandwich with GFRP laminates as a skin and PET foam as a core. Several static load schemes were performed including vertical and horizontal forces. In FEM analysis multilayered laminate...
-
A new approach of coastal cliff monitoring using Mobile Laser Scanning
PublikacjaThe article proposes a new approach of coastal cliff monitoring which bases on a new comprehensive monitoring system, being a combination of mobile scanning from the sea with the geotechnical stability analysis. Mobile laser scanning is an innovative solution for 3D data collection which allows the monitored object geometry to be precisely measured, thus providing opportunities for series of analyses contributing to the development...
-
Comparative analysis of the theoretical models of ideal propulsor, ideal fluid brake, ideal screw propeller and ideal axial wind turbine
PublikacjaThe article presents a detailed discussion of four different fluid dynamics devices.These devices are presented with all relevant mathematical formulae regarding the forces, the power and the efficiency. It is demonstrated that application of the Betz theorem to axial wind turbines is not correct and it underestimates the maximujm achievable efficiency. This conclusion is supported by numerical calculations.
-
15th Conference on Calorimetry and Thermal Analysis
WydarzeniaThe 15th Conference on Calorimetry and Thermal Analysis (CCTA 15) is the successive one in the cycle events coorganized by the Polish Society of Calorimetry and Thermal Analysis (PTKAT) this time Faculty of Chemistry of Gdańsk University of Technology and Stanislaw Staszic Research Association . The conference is devoted to application...
-
Pounding between high-rise buildings founded on different soil types
PublikacjaEarthquake-induced pounding is a phenomenon that has been often experienced in previous earthquakes. The aim of this study is to investigate the effect of the soil type on high-rise buildings experiencing earthquake induced-pounding. Pounding between 7-storey and 9-storey buildings is examined under five soil types defined in the ASCE 7-10 code which are hard rock, rock, very dense soil and soft rock, stiff soil and soft clay soil....
-
Investigation of stability and limit load of a truss overhead opened bridge
PublikacjaThe paper presents selected methods of determining stability and limit load of a truss top chord in opened bridges. These methods include linear buckling and non-linear static analysis based on the finite element method and algorithms based on design code procedures. The described methods were tested on an example of a steel footbridge situated in Straszyn. The results of stability analysis are compared. The results of geometrical...
-
Enhanced Remote Control Providing Medical Functionalities
PublikacjaThis paper presents the enhanced remote control and its role in pervasive healthcare in the home. The device was equipped with health-related measurement modules and a message-processing unit. Preliminary results are presented for monitoring of a pulse, hand tremors, grip forces, and for self evaluation procedures. The interaction of the device with the smart environment is presented and discussed.
-
Tyre rolling resistance and its influence on fuel consumption
PublikacjaRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Dynamics of fault arc traveling along busbars in high voltage switchboards = Dynamika łuku zwarciowego przemieszczającego się wzdłuż szyn rozdziel-nic wysokiego napięcia
PublikacjaThe paper presents the results of magnetic induction and electrodynamic force calculations acting on arc column during short-circuit in medium voltage air-insulated bus-bars. The gap between the bars was 120 mm and the prospective short-circuit currents ranged from 4 kA to 8 kA. The paper also shows the measurement results of average velocity fault arc depending on currents arc diameter and arc current was established and described....
-
SPECTRAL DYNAMIC ANALYSIS OF A STATIONARY JACK-UP PLATFORM
PublikacjaThe paper refers to the dynamic short-term response analysis of the Baltic steel drilling platform (see Fig.2) in a random sea-state represented by one-dimensional wave spectrum proposed by Striekalov and Massel and it is recommended for the Baltic Sea area. The Baltic drilling platform is a jack-up type platform for the exploration and exploitation of oil under the Baltic Sea. The analysis presented deals with the stationary...
-
Physical and mathematical modelling of implant-fascia system in order to improve laparoscopic repair of ventral hernia
PublikacjaThis paper describes an investigation of biomechanical behaviour of hernia repair, which is focused on the selection of safe linking of certain type of implant with fascia in laparoscopic operation. The strength of various fixations of the implant to the fascia is analysed. Methods: The research is based on experimental observations of operated hernia model behaviour during a dynamic impulse load corresponding to post-operative...
-
Road texture influence on tire rolling resistance
PublikacjaTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
Behaviour of asymmetric structures with base isolation made of Polymeric Bearings
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. During the last few years alone, the world has witnessed many major earthquakes, five of which have caused far-reaching consequences of a national scale for Haiti (January 2010), Chile (February...
-
COMPOSITE FOOTBRIDGE - SYNERGY EFFECT IN COOPERATION BETWEEN UNIVERSITIES AND INDUSTRY
PublikacjaPaper presents conditions of science and industry cooperation in Poland (restrictions, barriers, good practice). A key role in initiation of collaboration between units has financial support. What is also important, it is much easier to create innovative solutions on the base of combining the potential of individuals. That is why many countries all over the world look for innovative solutions using budget funds to support grants...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublikacjaPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublikacjaDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
Torsion of restrained thin-walled bars of open constant bisymmetric cross-section
PublikacjaElastic and geometric stiffness matrices were derived using Castigliano's first theorem, for the case of torsion of restrained thin-walled bars of open constant bisymmetric cross-section. Functions which describe the angles of torsion were adopted from the solutions of thedifferential equation for restrained torsion. The exact solutions were simplified by expanding them in a power series. Numerical examples were taken from Kujawa...
-
The Impact of Trade Integration with the European Union on Productivity in a Posttransition Economy: The Case of Polish Manufacturing Sectors
PublikacjaThis paper addresses the relationship between productivity growth in Polish manufacturing sectors and forces stemming from trade integration with the European Union. Empirical analysis (1995-2006) is based on sector-level bilateral data concerning both domestic (Polish) and foreign (partner countries from the enlarged European Union) markets' characteristics and their degree of openness. The main results indicate that, both in...
-
Janusz Datta prof. dr hab. inż.
OsobyJanusz Datta w roku 1988 ukończył studia na Wydziale Chemicznym Politechniki Gdańskiej. Po ich zakończeniu został zatrudniony na Wydziale Chemicznym w Zakładzie, a potem po reorganizacji, w Katedrze Technologii Polimerów, gdzie przez sześć lat pracował na stanowisku naukowo-technicznym. W tym okresie zdobywał doświadczenie uczestnicząc w licznych wyjazdach do Zakładów Chemicznych „Zachem” Bydgoszcz, gdzie brał udział w pracach...
-
Fluid Mechanics, L/L/E, DaPE, sem. 04, summer 21/22 (PG_00050282)
Kursy OnlineLECTURES Introduction and basic definitions. Properties of fluids. Models of fluids. Fluids in equilibrium. Determination of hydrostatic forces. Archimedes" law. Methods of fluid flow description. General motion of fluid. Deformation of fluid element. Vortex motion of fluid. Principles of conservation of mass, momentum and energy. Balance of entropy. Navier-Stokes equation. Bernoulli equation. Similarity of flow phenomena. Potential...
-
The nonlinear effects of sound in a liquid with relaxation losses
PublikacjaThe nonlinear effects of sound in electrolyte with a chemical reaction are examined. The dynamic equations that govern non-wave modes in the field of intense sound are derived, and acoustic forces of vortex, entropy, and relaxation modes are determined in the cases of low-frequency sound and high-frequency sound. The difference in the nonlinear effects of sound in electrolyte and in a gas with excited vibrational degrees of molecules,...
-
Dynamics of mechanical model of implant-tissue system in ventral hernia repair
PublikacjaThe paper deals with a finite element modelling of implants in the problem of ventral hernia repair. The synthetic mesh implanted in the abdomen during surgery is here modelled as a membrane structure. Thesystem undergoes the internal abdominal pressure that occurs during the postoperative cough, the load identified in the literature as the main cause of the connection failure and hernia recurrence. The model can be used to estimate...
-
The effect of an active force while slide diamond burnishing of wooden shafts upon process quality
PublikacjaThe quality of the surface of wooden elements that have been turned and burnished has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of the wooden surface after finishing (coating, painting). In the paper, selected results of the investigation of the effect of the burnishing process on the surface quality of the elements after turning are presented. Research experiments...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublikacjaThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
MODELLING OF TOXIC COMPOUNDS EMISSION IN MARINE DIESEL ENGINE DURING TRANSIENT STATES AT VARIABLE PRESSURE OF FUEL INJECTION
PublikacjaTransient states are an important part of the spectrum of engine loads, especially the traction engines. In the case of marine diesel engines, transient states are of particular importance in reducing the analysis of motion units for special areas and maneuvering in port, the participation of transient states in the load spectrum significantly increases, also, the emission of toxic compounds from this period increases proportionally....
-
Forum Innowacyjności Sił Zbrojnych
WydarzeniaOrganizatorami są Ministerstwo Obrony Narodowej, Wojskowa Akademia Techniczna, Narodowe Centrum Badań i Rozwoju
-
Investigation and operation problems of metal tanks in Poland
PublikacjaThe paper consists of three parts concerned with steel cylindrical, vertical tank for liquid fuel. In the first part the present trends in tank design and building in Poland are described. The main are: · reduction of environment contamination danger caused by tank leakage and hydrocarbons evaporation, · increasing capacity of new tanks (100000 m3 and more) due to economic factor - reduction of steel amount per m3 of storage capacity....
-
The influence of drying parameters on wood properties
PublikacjaThe influence of drying conditions on wood properties is presented. The classical approach was used to determine energetic effects (cutting forces and cutting power) of wood sawing process on the basis of the wood specific cutting resistance, material constant. Before mashining wood material (soft and hard) was dryied at various conditions using air at 25oC, air-steam meaxture at 80oC and steam at 110oC.
-
Pressure Pulsations in Turbine Blade Seal
PublikacjaThe paper presents the results of experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type. The performed experimental research proved that in a shroud clearance the pressure pulsates and the effects of the nozzle trailing edge thickness as well as the influence of the rotor blades are observed. The exemplary results...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublikacjaThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Pomiar sił w wantach mostu podwieszonego
PublikacjaW artykule przedstawiono metodę oraz wyniki badań sił w wantach Mostu III Tysiąclecia im. Jana Pawła II w Gdańsku. Do identyfikacji sił wykorzystano trzy metody: wibracyjną; z wykorzystaniem siłownika jednosplotowego (lift-off) oraz pomiaru strzałki ugięcia. Przedstawione wyniki badań dowodzą, że wszystkie metody mogą być z powodzeniem wykorzystywane do identyfikacji rzeczywistej siły w wancie. Każda z metod ma jednak ograniczenia...
-
Wojciech Litwin dr hab. inż.
Osoby1992÷1996 – Studia na Wydziale Mechanicznym Politechniki Gdańskiej1996 – Zatrudniony na Wydziale Oceanotechniki i Okrętownictwa PG2004 – Obrona pracy doktorskiej2014 – obrona rozprawy habilitacyjnej2012 – obejmuje funkcję prodziekan ds. Nauki na Wydziale Oceanotechniki i OkrętownictwaUczestniczył w wielu projektach badawczych oraz pracach zleconych przez przemysł związanych z łożyskowaniem ślizgowym wałów głównych oraz niekonwencjonalnymi...
-
Numerical study on pounding between two adjacent buildings under earthquake excitation
PublikacjaSeismic excitation, which results in large horizontal relative displacements, may cause collisions between two adjacent structures due to insufficient separation distance between them. Such collisions, known as earthquake-induced structural pounding, may induce severe damages. In this paper, the case of pounding between two adjacent buildings is studied by the application of single degree-of-freedom structural models. Impact is...
-
Synergistic effects in micellization and surface tension reduction in nonionic gemini S-10 and cationic RTAB surfactants mixtures
PublikacjaMixtures of nonionic gemini surfactant S-10 (α,α′-[2,4,7,9-tetrametyl-5-decyne-4,7-diyl]bis[ω-hydroxy -polioxyetylene] with cationic alkyltrimethylammonium bromides of different alkyl chain length (RTAB) were investigated. Basing on surface tension measurements the cmc values and other adsorption parameters were found. The Clint, Rubing’s and Rosen theories were applied for evaluation of the synergistic effects in mixed films and...
-
Reprezentation of mechanic hysteresis in a railway track using the Preisach model
PublikacjaThis paper presents an implementation of the classic scalar Preisach model to describe the hysteresis phenomenon created in a railway track subjected to lateral (in the horizontal plane) displacements. The principles of the Preisach theory and the scalar mathematical model of the mechanical hysteresis that is based on statistically distributed modified hysteresis operators are briefly presented. This article presents the characteristic...
-
Effect of soil on the capacity of viscous dampers between adjacent buildings
PublikacjaThis study investigated the seismic pounding of two adjacent buildings considering soil–structure interaction (SSI). A comprehensive parametric study of buildings with different heights was performed to reveal the pounding-involved behaviour considering the soil effect. Wavelet transform has been conducted to gain insight into the differences in the frequency contents of the impact forces between fixed- and flexible-base adjacent...
-
Designing Particle Kalman Filter for Dynamic Positioning
PublikacjaThe article presents a comparative analysis of two variants of the Particle Kalman Filter designed by using two different ship motion models. The first filter bases only on the kinematic model of the ship and can be used in many types of vehicles, regardless of the vehicle dynamics model. The input value to the filter is the noisy position of the ship. The second filter makes use of the kinematic and dynamic models of the moving...
-
Reverberation chamber in emc tests of naval systems
PublikacjaPaper covers the techniques of emission and immunity testing to the electromagnetic field in reverberation chamber. The procedure of he chamber calibration and field homogeneity assessment were covered. The naval forces' product as selected as an example for discussing the testing procedure in the chamber. The paper's summary gives the assortment of methodology in radiation emission testing and immunity to the electromagnetic field...
-
On some problems in determining tensile parameters of concrete model from size effect tests
PublikacjaThe paper presents results of numerical simulations of size effect phenomenon in concrete specimens. The behaviour of in-plane geometrically similar notched and unnotched beams under three-point bending is investigated. In total 18 beams are analysed. Concrete beams of four different sizes and five different notch to depth ratios are simulated. Two methods are applied to describe cracks. First, an elasto-plastic constitutive law...
-
Effective Formula for Impact Damping Ratio for Simulation of Earthquake-induced Structural Pounding
PublikacjaStructural pounding during earthquakes may cause substantial damage to colliding structures. The phenomenon is numerically studied using different models of collisions. The aim of the present paper is to propose an effective formula for the impact damping ratio, as a parameter of the impact force model used to study different problems of structural pounding under seismic excitations. Its accuracy has been verified by four various...
-
Mechanical lithography in a polymer substrate using AFM in contact mode
Dane BadawczeMechanical lithography in a polymer substrate. Contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
-
The Method of Finding the Optimal Spindle Speed When Milling Flexible Details
PublikacjaThe paper presents a new method of vibration reduction during milling of flexible details. The method consists in selecting the optimal spindle speed, based on the natural frequency of the workpiece. For this purpose, an original method was created, which is based on minimizing the work of cutting forces in the direction of the depth of cutting. The effectiveness of the method has been proved by comparing the RMS values of vibration...
-
Dynamics of the small-span railway bridge under moving loads
PublikacjaThe paper presents the results of dynamic analysis of the small-span railway bridge, subjected to an action of moving trains. Numerical simulations were performed using three different load models: series of moving forces, series of moving single-mass and double-mass oscillators. The parameters of the vehicle were taken from the existing EN57 train. The parameters of the bridge were taken from the existing steel span of 10,24 m...
-
Artificial-Hand Technology—Current State of Knowledge in Designing and Forecasting Changes
PublikacjaThe subject of human-hand versatility has been intensively investigated for many years. Emerging robotic constructions change continuously in order to mimic natural mechanisms as accurately as possible. Such an attitude is motivated by the demand for humanoid robots with sophisticated end effectors and highly biomimic prostheses. This paper provides wide analysis of more than 80 devices that have been created over the last 40 years....
-
Adiabatic potential energy curves of the triplet Sigma ungerade plus states of the Lithium dimer
Dane BadawczeAdiabatic potential energy curves of the triplet Sigma ungerade plus states have been calculated for the Lithium dimer. The results of the five excited states of the symmetry triplet Sigma ungerade plus have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials describing the interaction...
-
Characterization of the Functionally Graded Shear Modulus of a Half-Space
PublikacjaIn this article, a method is proposed for determining parameters of the exponentialy varying shear modulus of a functionally graded half-space. The method is based on the analytical solution of the problem of pure shear of an elastic functionally graded half-space by a strip punch. The half-space has the depth-wise exponential variation of its shear modulus, whose parameters are to be determined. The problem is reduced to an integral...
-
SIMPLIFIED DYNAMIC MODEL OF ROTATING BEAM
PublikacjaIn the paper a hybrid model of rotating beam is presented. It was obtained by using two methods: modal decomposition and spatial discretization. Reduced modal model was built for the system without the load related to inertia forces that occur during beam rotation. This inertia load was next modeled by using the method of simply spatial discretization and combined with reduced modal model. This approach allows to obtain accurate...
-
UWARUNKOWANIA I SKUTKI ŻYWIOŁOWEJ SUBURBANIZACJI W POLSCE. CZY OPANOWANIE JEJ JEST MOŻLIWE?
PublikacjaArtykuł dotyczy procesu żywiołowej suburbanizcji (urban sprawl) w Polsce. Jego celami są: (1) analiza powiązań między negatywnymi skutkami tego procesu, (2) prezentacja negatywnych skutków dla transportu i zużycia energii oraz ładu przestrzennego, (3) analiza sposobów przeciwdziałania negatywnym procesom, w tym uwarunkowań (w szczególności ograniczeń) stosowania tych sposobów i ich skuteczności. Jako metody zastosowano: obserwację,...
-
Synthesis of Novel Polycationic Quaternary Di- and Trispirocyclic Benzenes
PublikacjaTreatment of hexakis(bromomethyl)benzene with a cyclic amine {morpholine, 1-methylpiperazine, 1-(2-hydroxyethyl)piperazine, isonipecotamide, 4-hydroxypiperidine, 4-[3-(4-piperidyl)propyl]-1-piperidineethanol} gave a range of di- and trispirocyclic ammonium salts in satisfactory yields (22-62%). Presumably, the electrostatic and repulsion forces play an important role in their formation. The structure in soln. and the protonation...
-
Topographic AFM imaging of the leaf surface with magnification of details of its morphological structure
Dane BadawczeTopographic imaging of the leaf surface with magnification of details of its morphological structure. Measurements in semi-contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
-
Impacts in case of triple unilaterally constrained system
PublikacjaThe this paper focus on the behaviour of a “rigid” body biting into another “rigid” body, with some nonzero relative velocity. In the presently considered case, the introduced collision appears between a selected element of a multibody structure and its reference body being interpreted as the motionless ground. Instead of the classic case, described in a number of dissertations, where a single impacting contact is considered, three...
-
Analyses of Shear Angle in Orthogonal Cutting of Pine Wood
PublikacjaThe determination of energy effects for wood machining processes, such as cutting power and cutting forces, is very useful in designing of manufacture process of wooden products. A more accurate prediction of cutting forces requires a correct determination of the shear angle value, which can be determined using various models. In this article, shear angle values for an orthogonal linear cutting process of pine wood are determined. The...
-
Galerkin Finite Element Process for Entropy Production and Thermal Evaluation of Third-Grade Fluid Flow: A Thermal Case Study
Publikacja: A fluid’s moving class improves its heat transmission capability, as well as its rigidity, owing to multivariate molecule suspension. In this way, nanofluids are superior to common fluids. In this study, we evaluated the features of ease and heat transfer. Furthermore, we investigated permeable media, heat source, variable heat conductivity, and warm irradiation results. A mathematical technique known as the Galerkin finite element...
-
Potential energy curves of the doublet Sigma ungerade plus states of the Lithium dimer cation
Dane BadawczeAdiabatic potential energy curves of the doublet Sigma ungerade plus (dSu+) states have been calculated for the Lithium dimer cation (Li2+). The results of the five excited states of the symmetry doublet Sigma ungerade plus have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials describing...
-
Analysis of passenger car crash with a cable barrier installed with anti-glare screens on a horizontal convex road curve with 400 m radius
PublikacjaHigh-tension cable barriers have been used on roads for a relatively short period compared with other types of road barriers. Hence, there remains a need for further research on various crash scenarios. An important issue is the performance of a cable barrier on a road curve, particularly when a vehicle impacts the convex side of the barrier. To address this issue, the analysis in this study considers a system of anti-glare screens...
-
Accuracy improvement of the prestressed concrete structures precise geometry assessment by use of bubble micro-sampling algorithm
PublikacjaPrestressed concrete structures are well-known technology for a vast period, but nevertheless, this very technology is a leading solution, currently used in construction industry. Prestressed concrete structures have a huge advantage over conventional methods because it uses the properties of concrete in a very efficient way. The main idea behind this technology is to introduce into the cross-section of the structure, the internal...
-
STRENGTH of MATERIALS TOWARDS APPLICATIONS (2024)
Kursy OnlineThe SMTA DATE Course consists of the following problems to be discussed during the lectures: - Introduction to strength of materials towards applications - Fundamentals of modelling in strength of materials towards applications - Materials and basic structures - Fundamentals of modelling in strength of materials towards applications - Definition of environment and loads - General, energy-based and advanced methods for analysis...
-
Compensation of pressure peaks in pwk-type hydraulic pumps
Publikacjahydraulic axial pumps equipped with cam-driven commutation unit (pwk pumps) proved their high efficiency up to 55 mpa and ability to work self-sucking, even at high speed. displacement of pwk pump may easily be changed by moving its control cam. full discharge from hydrostatic forces makes such control possible by direct action of a low-energy actuator like proportional electromagnet or stepping motor. that eliminates heavy and...
-
Skilled-Unskilled Wage Gap Versus Evolving Trade And Labour Market Structures in the EU
PublikacjaThis paper proposes an alternative approach to the empirical study of wage gap between workers with different educational levels in the enlarged EU. The analysis is based on sectoral database, linking labor market statistics and trade data at the level of 12 manufacturing sectors in a group of 20 European countries: selected New Member States (NMS-5) and former EU-15 economies, in the period 1995-2005. The results of the empirical...
-
Pressure pulsations in turbine blade seal clearance
PublikacjaThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type, while the numerical results were obtained by means of CFD Fluent Code. The performed experimental research and numerical calculations prove that in a shroud clearance the pressure pulsates and the effects of...