Filtry
wszystkich: 7185
wybranych: 1161
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TD-SFEM
-
Train the trainer course
PublikacjaThis chapter presents the concept, evaluation and evaluation results for the train the trainer. This concept of train the trainers is prepared within Workpackage 5 of EU-funded project: MASTER BSR (Erasmus+ Strategic Partnership Programme). Due to the nature of adult learning the content is designed for the use of participatory methods (involved, active). This method uses various techniques of active learning e.g. group work,...
-
Fabrication and structural properties of Y and Fe co-doped SrTiO3 nanoceramics for SOFC
PublikacjaYttria and iron co-doped strontium titanate perovskites, (Y0,07Sr0,93Ti1-xFexO3-δx=0,1; 0,2) samples were fabricated by two methods: solid-state synthesis (SS) and the Pechinisol-gel modified method. The morphology of samples were measured by SEM and X-raydiffraction. Results were compared and discussed. The strong relationship between fabricationprocedure and microstructure has been proven. It was also observed, that the nanoceramicsobtained...
-
Comparative Analysis of Salient and Non-Salient Pole Brushless Synchronous Generator for Application in Autonomous Electric Power System
PublikacjaThis paper presents a comparative study of two types of brushless synchronous generator for application in autonomous electric power systems (e.g. airplane power grid). Commercially used salient pole and a prototype non-salient pole high speed multi-pole brushless synchronous generator (BSG) have been presented. Comparative analysis of both types of the generator has been performed. Chosen simulation (using FEM and circuit models)...
-
Liquid-solid interaction during formation of nanocomposite systems
PublikacjaW pracy zaprezentowano wyniki badań nad zmianami strukturalnymi w układach ciekłego Bi i małych cząsteczek Ni lub Cu w zakresie temperatur od 615 do 1145K. Zaobserwowano (SEM) mikrostruktury kompozytowe i przeanalizowano dla różnych temperaturach i różnych czasów mieszania. Strukturę układów Bi-Ni oraz Bi-Cu, zarówno w stanie stałym i ciekłym, zbadano za pomocą dyfrakcji rentgenowskich.
-
ECONOMICAL AND SAFE METHOD OF GRANULAR MATERIAL STORAGE IN SILOS IN OFFSHORE PORT TERMINALS
PublikacjaThe article discusses issues related with storage of granular materials in silos made of corrugated sheets and reinforced with vertical ribs. Advantages and disadvantages of these structures are named, and typical technological solutions used by largest silo producers are presented. Moreover, basic assumptions of Eurocode 3 are discussed in the context of determining the buckling load capacity of a ribbed jacket. Alternative methods...
-
Determination of equivalent circuit parameters of an induction motor using field calculation software
PublikacjaSimulation of the drive system comprising a power electronic converter and an induction motor requires that the equivalent circuit parameters of the motor are known. These parameters can be either measured or calculated. A method of calculation of self and mutual inductances that are parameters of a polyphase model of the motor is presented in the paper. All self-inductances and mutual inductances have been calculated using the...
-
The impact of China’s One-Belt One-Road initiative on international trade and global value chains
PublikacjaThis study examines the potential effects of China’s ‘One-Belt One-Road’initiative (OBOR) on trade flows and global value chain (GVC) connections.The empirical analysis is based on the augmented trade gravity model, which comprises 186 economies and 199 of their partners from 2000 to 2018. We also estimate the gravity model for involvement in GVC (domestic value added in intermediate exports, foreign value added in exports, and...
-
Massive Open Online Courses: strategies and research areas
PublikacjaThe latest education revolution, the massive open online courses (MOOCs), is gaining momentum, accolades, and participation across industry and academia. These learning laboratory behemoths host and assess tens to hundreds of thousands of students in a single class, for free. Similar to their scope, MOOCs’ short- and long-term educational implications seem massive. Immediate MOOC educational outcomes vary widely from roaring successes...
-
Modeling of wood frame structures with different insulation materials under damaging dynamic loading
PublikacjaWood frame buildings are very popular in regions that are exposed to different dynamic excitations, such as damaging earthquakes. Their seismic resistance is really important in order to prevent structural damages and human losses. This paper presents the results of advanced numerical investigation carried out using the FEM. Based on the models of wall panels, the numerical model of real structure of the wood frame building has...
-
The Synergistic Microbiological Effects of Industrial Produced Packaging Polyethylene Films Incorporated with Zinc Nanoparticles
PublikacjaZinc compounds in polyolefin films regulate the transmission of UV-VIS radiation, affect mechanical properties and antimicrobial activity. According to hypothesis, the use of zinc- containing masterbatches in polyethylene films (PE) with different chemical nature—hydrophilic zinc oxide (ZO) and hydrophobic zinc stearate (ZS)—can cause a synergistic effect, especially due to their antimicrobial properties. PE films obtained on an...
-
Estakada E2 - kluczowy obiekt Obwodnicy Wałcza
PublikacjaW artykule przedstawiono uwarunkowania i przebieg projektowania estakady E2 z betonu sprężonego w ciągu Obwodnicy Wałcza. Pokazano efekt procesu optymalizacji projektu pierwotnego. Opisano przeprowadzone analizy wynikające z przyjętej technologii nasuwania podłużnego oraz istotne aspekty, które należy poruszyć przy wyborze tej technologii. Zaprezentowano modele numeryczne konstrukcji przęseł i metodę analizy z uwzględnieniem pracy...
-
FEA analysis of the multicell piezoelectric motor
PublikacjaThe presented paper concerns a design, modeling and chosen tests of the prototype multicell piezoelectric motor (MPM). The principle of operation based on three independent traveling wave actuators is presented. The main materials and technologies used in the fabrication process are described. The structure of the motor is modeled using static and modal FEM analysis. The process of traveling wave generation in the MPM structure...
-
High temperature oxidation of porous alloys for solid oxide fuel cell applications
PublikacjaW pracy proszki PI600, 317L i 430L stali użyto do przygotowania porowatych metalowych podłoży dla tlenkowych ogniw paliwowych. Po spiekaniu w różnych temperaturach oceniana była ich porowatość i wysokotemperaturową odporność na korozję. Cykliczna analiza termograwimetryczna, dyfraktometria rentgenowska i obrazów SEM były używane do opisu właściwości tych porowatych stopów. Właściwości elektryczne badano dla wybranych próbek. Wpływ...
-
ANALYSIS OF THE PUNCHING FAILURE MECHANISM IN WORKING PLATFORMS
PublikacjaPaper presents an analysis of the shear failure mechanism which occurs from the punching of a working platform layer in relation to its thickness, grain size arrangement and mechanical properties, taking into consideration the interaction with soft subgrade. The study is based on the observations of performance of natural scale structures (Streefkerk) and the results of model investigations numerically represented with the use...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublikacjaThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...
-
Determination of leakage inductances of multi-winding and single-phase transformer
PublikacjaThis paper presents the method for determination of leakage inductances of single-phase and multi-winding transformer. The matrix of leakage inductances takes into account leakage self and also leakage mutual magnetic couplings. It is assumed that there is a flux common to all windings and several leakage fluxes referred to a particular winding. The flux linkages of each coil needed fo calculation of leakage inductances was computed...
-
Improvement of electrochemical action of zinc-rich paints by addition of nanoparticulate zinc
PublikacjaThe influence of nanosized particles on electrochemical action of standard zinc-rich paints by means of SEM as well as potential and impedance measurements has been investigated. The motivation for doing this was to obtain additional electrical connection between the spherical microparticles themselves and zinc particles and steel substrate. Overall zinc content was at the level of 92% by weight. Samples with different concentration...
-
Evaluation of cavitation erosion-corrosion degradation of mild steel by means of Dynamic Impedance Spectroscopy in galvanostatic mode
PublikacjaPrzedstawiono wyniki badań degradacji stali węglowych na skutek oddziaływania erozji-korozji kawitacyjnej. Do analizy wykorzystano technikę Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej w trybie galwanostatycznym, bliżej odwzrorowującym warunki naturalne. Do oceny stopnia degradacji posłużyły również funkcja ubytku masy MDPR oraz obrazy mikroskopowe SEM. Potwierdzono wpływ łączonej degradacji erozyjno-korozyjnej na...
-
Wpływ metody wytwarzania na właściwości laminatów poliestrowo/szklanych do budowy małych jednostek pływających
PublikacjaW pracy porównano pod względem mikrostruktury i wybranych wskaźników wytrzymałościowych jakość laminatów poliestowo/szklanych wytworzonych w zakładzie budowy dużych łodzi motorowych za pomocą metod: ręcznej, worka próżniowego i infuzji. Badano jakość struktury pod kątem udziału osnowy żywicznej i liczby pęcherzy za pomocą SEM i analizy obrazu. Porównano własności mechaniczne na podstawie prób: trzypunktowego zginania, ścinania...
-
DYNAMIC RESPONSE OF FORUM GDANSK STRUCTURE DUE TO RAIL TRAFFIC
PublikacjaThe paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing...
-
Strength parameters of masonry walls in modelling historic constructions
PublikacjaThe paper presents the determination of the basic material properties of a historic brickwork. Experimental studies were used to identify the basic material properties of bricks. The mechanical properties of the masonry, as an orthotropic homogenized material, were calculated. Then, numerical simulations using the Finite Element Method (FEM) were performed to verify the experimental outcomes. Macromodels with element sizes of 40,...
-
Electrical conductivity and relaxation processes in V2O5 nanorods prepared by sol–gel method
PublikacjaProperties of high purity V2O5 nanorods prepared by a sol – gel method are presented. The studied materials were characterized by: X-ray diffractometry (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The electrical impedance was measured as a function of temperature and frequency. The obtained results show that the electrical conductivity increases with increasing temperature. The d.c. conductivity...
-
Instantaneous impedance monitoring of AA 7075 aluminum alloy corrosion in borate buffer with admixed chloride ions
PublikacjaThe study presents a research capabilities of Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a tool used for instantaneous on-line monitoring of corrosion processes on the example of AA 7075 aluminum alloy. A borate buffer with admixed chloride ions in a quantity ranging from 0.05 to 25 mM was used to represent different types of corrosion attack. The surface of samples specimens was evaluated before and after the tests...
-
THEORETICAL AND EXPERIMENTAL INVESTIGATION OF THIN-WALLED BEARING SHELL’S DESIGN PARAMETERS AND ASSEMBLY CONDITIONS ON THE HOLDING TORQUE INSIDE A HOUSING BORE OF A CONNECTING ROD
PublikacjaThe aim of the work was the experimental and theoretical evaluation of the influence of the most important parameters determining the holding torque of a thin-walled bearing shell inside a housing bore of a connecting rod. The main investigated parameters were defned by authors experience in this feld. In the frst stage of research, a special test stand was designed in order to allow measuring the real values of the friction torque...
-
Special Issue "Applications of Finite Element Modeling for Mechanical and Mechatronic Systems"
PublikacjaNumerical modeling is very important in today's engineering because, among other things, it reduces the costs associated with prototyping or predicting the occurrence of potentially dangerous situations during operation in certain defined conditions. Different methods have so far been used to implement the real structure into the numerical version. The most popular have been variations of the finite element method (FEM). The aim...
-
Detection of defects in PMMA beam using shear waves - numerical simulation and experiment
PublikacjaTest doświadczalny falami sprężystymi jest częścią systemu diagnostycznego belek. Autorzy badają pole przyspieszeń wywołane przepływem fal ultradźwiękowych i jego modyfikacje wynikające z wprowadzonych uszkodzeń belki. Artykuł porównuje wyniki eksperymentalne z symulacjami numerycznymi MES. The experimental test introduced in the paper is the part of the diagnostic system utilizing the elastic waves. The authors investigate the...
-
The Impact of EU Funds on the Development of Business Environment Institutions – Research Results in Pomeranian Voivodeship in Poland
PublikacjaThe paper presents the main findings of the research conducted to assess the impact of EU funds on development of business environment infrastructure in Pomeranian Voivodeship in Poland, and – indirectly – on the growth of the innovation capacity of Pomeranian entrepreneurs. The research shows that support of ROP PV 2007-2013 contributed to the creation of multifunctional business infrastructure throughout the Pomorskie Voivodship,...
-
Source-related Wavefields in Fluids and Dielectrics: A new way of Thinking about Medium Dynamics
PublikacjaAcoustic and electromagnetic wave phenomena may seem to have a proper formal representation in field theory dating from the 19th century, founded on the mathematics of complex functions. This paper shows, however, that when replacing the classical spectrum-domain approach related to the assumption of harmonic timeform of signals, with a time-domain approach imposingnorestrictionastotheclassoftimeevolutionofsourceandfieldsignals,...
-
Performance of a single layer fuel cell based on a mixed proton-electron conducting composite
PublikacjaMany of the challenges in solid oxide fuel cell technology stem from chemical and mechanical incompatibilities between the anode, cathode and electrolyte materials. Numerous attempts have been made to identify compatible materials. Here, these challenges are circumvented by the introduction of a working single layer fuel cell, fabricated from a composite of proton conducting BaCe0.6Zr0.2Y0.2O3-δ and a mixture of semiconducting...
-
Limitations of Emotion Recognition in Software User Experience Evaluation Context
PublikacjaThis paper concerns how an affective-behavioural- cognitive approach applies to the evaluation of the software user experience. Although it may seem that affect recognition solutions are accurate in determining the user experience, there are several challenges in practice. This paper aims to explore the limitations of the automatic affect recognition applied in the usability context as well as...
-
Novel analysis methods of dynamic properties for vehicle pantographs
PublikacjaTransmission of electrical energy from a catenary system to traction units must be safe and reliable especially for high speed trains. Modern pantographs have to meet these requirements. Pantographs are subjected to several forces acting on their structural elements. These forces come from pantograph drive, inertia forces, aerodynamic effects, vibration of traction units etc. Modern approach to static and dynamic analysis should...
-
Insight into the microstructural and durability characteristics of 3D printed concrete: Cast versus printed specimens
PublikacjaThis study presents the comparison of microstructural and durability characteristics of 3D printed concrete (3DPC) depending on its production method (printing or casting). Printed samples with different numbers of layers, as well as a cast specimen with an identical mix composition, were produced and compared, with their microstructural pore and solid characteristics quantitatively and qualitatively investigated. For this purpose,...
-
Reinforced concrete thin wall dome after eighty years of operation in maritime climate environment
PublikacjaThe paper presents a description of the construction elements of the Gdynia Seaport main hall dome. Firstly, it provides information about the technical condition of the dome’s structure. Secondly, it examines the strength analysis of the thin-walled reinforced concrete dome covering. Throughout the last 80 years the building has been exposed to an unfavourable marine climate. The analysis of the state of stress and deformations...
-
A multi-analytical approach to the characterization of natural organic dyestuffs and inorganic substrates present in the 19th-century artistic oil paints manufactured by a French art materials supplier Richard Aines
PublikacjaThis paper presents a comprehensive analysis of artistic paints produced in the 19th century by a French art materials supplier Richard Ain`es. Improved mild extraction with hydrofluoric acid enabled the observation of intact organic dyes. Reversed-phase liquid chromatography with diode-array and mass spectrometry detection was utilised for the identification of 35 dyes present in yellow and red paint samples, and in selected plant...
-
Effect of kenaf fibre modification on morphology and mechanical properties of thermoplastic polyurethane materials
PublikacjaThe presented study examined the morphology and mechanical properties of biocomposites obtained from kenaf natural fibre and thermoplastic polyurethane. Kenaf was modified using various methods, namely: acetylation, blocked isocyanate, maleic anhydride and permanganate treatment. Those methods and ways of carrying out of surface modifications were not studied before on kenaf/thermoplastic polyurethane composites. Different fibre...
-
Experimental and Numerical Investigation of Tensile and Flexural Behavior of Nanoclay Wood-Plastic Composite
PublikacjaIn this study, the effect of wood powder and nanoclay particle content on composites’ mechanical behavior made with polyethylene matrix has been investigated. The wood flour as a reinforcer made of wood powder was at levels of 30, 40, and 50 wt.%, and additional reinforcement with nanoclay at 0, 1, 3, and 5 wt.%. Furthermore, to make a composite matrix, high-density polyethylene was used at levels of 70, 60, and 50% by weight....
-
A facile approach to fabricate load-bearing porous polymer scaffolds for bone tissue engineering
PublikacjaBiodegradable porous scaffolds with oriented interconnected pores and high mechanical are load-bearing biomaterials for bone tissue engineering. Herein, we report a simple, non-toxic, and cost-effective method to fabricate high-strength porous biodegradable scaffolds, composed of a polymer matrix of polycaprolactone (PCL) and water-soluble poly (ethylene oxide) (PEO) as a sacrificial material by integrating annealing treatment,...
-
GTR/Thermoplastics Blends: How Do Interfacial Interactions Govern Processing and Physico-Mechanical Properties?
PublikacjaIn this work, GTR/thermoplastics blends (in ratio 50/50 and 75/25 wt.%) were prepared by melt-compounding in an internal mixer. During research, trans-polyoctenamer rubber (TOR), ethylene-vinyl acetate copolymer (EVA), ethylene-octene copolymer (EOC), and linear low-density polyethylene (LLDPE), were used in their thermoplastic phase. Microstructure and processing-performance property interrelationships of the studied materials...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublikacjaThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Multi-Technique Investigation of Grave Robes from 17th and 18th Century Crypts Using Combined Spectroscopic, Spectrometric Techniques, and New-Generation Sequencing
PublikacjaThe textile fragments of the funeral clothes found in the 17th and 18th century crypts were subjected to spectroscopic, spectrometric, and microbial investigation. The next-generation sequencing enabled DNA identification of microorganisms at the genus and in five cases to the species level. The soft hydrofluoric acid extraction method was optimized to isolate different classes of dyes from samples that had direct contact with...
-
Fabrication of the cross-linked PVA/TiO2/C nanocomposite membrane for alkaline direct methanol fuel cells
PublikacjaA crosslinked Poly(vinyl alcohol) based composite membrane was developed through a phase inversion process for use in alkaline direct methanol fuel cells (ADMFCs). The titanium dioxide (TiO2) and carbon nanoparticles (NPs) have been incorporated into the PVA polymer matrix to improve the mechanical and thermal properties. The membrane samples were further modified with maleic acid, a carboxylic acid acting as the cross-linker,...
-
Solar light driven degradation of textile dye contaminants for wastewater treatment – studies of novel polycationic selenide photocatalyst and process optimization by response surface methodology desirability factor
PublikacjaThe unplanned anthropogenic activities and raced industrial revolution detrimentally causes serious threat to terrestrial and aquatic life. A high discharge of wastewater from industries using dyes affects living organisms and the environment. This paper presents studies on polycationic selenides (PCS) synthesized by hydrothermal methods for photocatalytic degradation of dyes. The synthesized PCS were confirmed by various characterization...
-
Wpływ zawartości grafitu na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit osadzonych na stopie AW-7075 metodą redukcji chemicznej.
PublikacjaPrzedstawiono wpływ obecności grafitu jako fazy dyspersyjnej na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit, które osadzono metodą redukcji chemicznej na stopie glinu AW-7075. Wykonano badania morfologii powierzchni warstw metodą mikroskopii świetlnej i skaningowej. Dalszą część pracy stanowiły badania mechaniczne, czyli pomiary mikrotwardości warstw oraz ich adhezji do aluminiowego podłoża, a także analizy wpływu...
-
Nieliniowa statyka 6-parametrowych powłok sprężysto plastycznych. Efektywne obliczenia MES
PublikacjaGłównym zagadnieniem omawianym w monografii jest sformułowanie sprężysto-plastycznego prawa konstytutywnego w nieliniowej 6-parametrowej teorii powłok. Wyróżnikiem tej teorii jest występujący w niej w naturalny sposób tzw. stopień 6 swobody, czyli owinięcie (drilling rotation). Podstawowe założenie pracy to przyjęcie płaskiego stanu naprężenia uogólnionego na ośrodek typu Cosseratów. Takie podejście stanowi oryginalny aspekt opracowania....
-
Application of the Bodner-Partom constitutive equations for modelling of the technical fabric Valmex used for the hanging roof of the Forest Opera in Sopot
PublikacjaThe study of an inelastic properties of the technical fabric Valmex used for 20 years as the roof structure of the Forest Opera in Sopot (Poland) is presented. The uniaxial tensile laboratory tests with constant strain rate have been conducted and analysed. Parameters of the Bodner-Partom constitutive model have been identified and verified by numerical simulations. Two approaches of the parameters identification have been proposed:...
-
A Stand for Measurement and Prediction of Scattering Properties of Diffusers
PublikacjaIn this paper we present a set of solutions which may be used for prototyping and simulation of acoustic scattering devices. A system proposed is capable of measuring sound field. Also a way to use an open source solution for simulation of scattering phenomena occurring in proximity of acoustic diffusers is shown. The result of our work are measurement procedure and a prototype of the simulation script based on FEniCS - an open source...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublikacjaThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Impedance Studies of Phosphate-iron Glasses Containing Niobium and Titanium
PublikacjaThe ac and dc conductivity in phosphate-iron-niobate glasses with addition of titanium oxide was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and confocal microscopy methods. The obtained results show that all samples are amorphous but they...
-
Phase Separation and Electrical Properties of Manganese Borosilicate Glasses
PublikacjaThe structure and electrical properties of manganese borosilicate glasses of a composition of xMnO-(0.8-x)SiO2-(0.2)B2O3 (x=0.4, 0.5 and 0.6 in mol) were investigated by impedance spectroscopy, SEM, XRD and confocal microscopy methods. The influence of composition on the glass structure and electrical properties was discussed. A separation of two amorphous phases was observed and it was concluded that one phase is SiO2-rich and...
-
Influence of Processing Conditions on Crystal Structure of Bi6Fe2Ti3O18 Ceramics
PublikacjaAim of the present research was to apply a solid state reaction route to fabricate Aurivillius-type ceramics described with the formula Bi6Fe2Ti3O18 (BFTO) and reveal the influence of processing conditions on its crystal structure. Pressureless sintering in ambient air was employed and the sintering temperatures were 850 and 1080 °C. It was found that the fabricated BFTO ceramics were multiphase ones. They consisted of two Bim+1Fem-3Ti3O3m+3...