Filters
total: 2097
displaying 1000 best results Help
Search results for: : CLOSING CRACK
-
Audio codec employing frequency-derived tonality measure
PublicationA transform codec employing efficient algorithm for detection of spectral tonal components is presented. The tonality measure used in MPEG psychoacoustic model is replaced with the method providing adequate tonality estimates even if the tonal components are deeply frequency modulated. The reliability of hearing threshold estimated using psychoacoustic model with standardized tonality measure and the proposed one is investigated...
-
Operational causes of fatigue failures within the passages of gas turbine engines
PublicationThe short profile of a fatigue wear process of gas turbine engine's constructional elements has been introduced in the article. The primary causes of a fatigue cracks formation within the mechanical system as well as within the passages of the engine have been showed. Especial attention was devoted to the low-cycle fatigue, what is associated with unsteady thermal-flow processes being worked out in the passages.The selected damages...
-
EXPERIMENTAL AND THEORETICAL FLOW OF THE FORCES IN DEEP BEAMS WITH CANTILEVAR
PublicationThis article presents the results of experimental research carried out on deep beams with cantilever which was loaded throughout the depth. The main deep beam was directly simply supported on the one side. On the other side the deep beam was suspended in another deep member situated at right angles. All deep beams created a spatial arrangement. The paper is focused on the analysis of the cracks morphology and flow of the internal...
-
Causes of damage and methods of repairing floor made on polystyrene concrete
PublicationThe paper describes damages, tests and repair of the floor made on existing ceiling and expanded polystyrene concrete underlay. The floor was built on a reinforced concrete ceiling with an area of about 1050 m2. Significant damage in the form of cracks, detachments and unevenness was found in the floor. In order to determine the causes of damage, in situ tests and laboratory tests were carried out. It was found that the damage...
-
Prototype and design of six axis robotic manipulator
PublicationThe paper presents a design of six axis manipulator. The design consists of specially designed solutions for housing, planetary gearboxes and electronics. The manipulator is controlled by a supervisory control system. The use of a series of measuring elements allows to track the current position of each axis and use this to create a cascade control loop with velocity and acceleration feed-forward. The implemented control algorithm...
-
Mechanical lithography in a polymer substrate using AFM in contact mode
Open Research DataMechanical lithography in a polymer substrate. Contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
-
Knowledge Base Suitable for Answering Questions in Natural Language
PublicationThis paper presents three knowledge bases widely used by researchers coping with natural language processing: OpenCyc, DBpedia and YAGO. They are characterized from the point of view of questions answering system. In this paper a short description of the aforementioned system implementation is also presented.
-
PROBABILISTYCZNE ASPEKTY ZUŻYCIA SKOJARZEŃ CIERNYCH UKŁADÓW KORBOWO-TŁOKOWYCH NA PRZYKŁADZIE OKRĘTOWYCH SILNIKÓW SPALINOWYCH DWUSUWOWYCH NAPĘDU GŁÓWNEGO
PublicationW artykule przestawiono propozycję rozpatrywania zarówno obciążenia jak i zużywania ślizgowych skojarzeń ciernych (łożysk głównych i korbowych) układów korbowo-tłokowych silników spalinowych, zwłaszcza głównych, a także skojarzeń „tłok-tuleja” tych silników, jako procesów stochastycznych. Propozycję tę uzasadniono tym, że deterministyczne podejście do badania zarówno obciążenia jak i zużycia wspomnianych skojarzeń uniemożliwia...
-
Assessment of the impact of jet impingement technique on the energy efficiency of air-cooled BIPV/T roof tile
PublicationThe paper concerns a numerical analysis of cooling of the hybrid photovoltaic (PV) modules dedicated to Building-Integrated Photovoltaic/Thermal (BIPV/T) systems. Attention was focused on the photovoltaic roof tiles, using a jet impingement technique, in which the intensification of heat transfer is ensured by streams of air hitting the heat exchange partition. A series of numerical simulations were carried out to assess an influence...
-
Electric transport in organic system with planar DBP/F16ZnPc junction on the basis of direct current and small signal admittance spectra analysis
PublicationThe objective of this work was to determine electric transport in the organic device based on a planar junction of electron donor and electron acceptor materials, namely ITO/MoO3/DBP/F16ZnPc/BCP/Ag. The analysis reported herein was based on direct current-voltage measurements and small-signal admittance spectra in the dark and under illumination. Such analysis may provide information on potential barriers, parasitic resistances...
-
Hysteresis curves for some periodic and aperiodic perturbations in magnetosonic flow
PublicationA thermodynamic relation between perturbations of pressure and mass density in the magnetohydrodynamic flow is theoretically studied. Planar magnetohydrodynamic perturbations with the wave vector, which forms a constant angle with the equilibrium magnetic field, are under study. The theory considers thermal conduction of a plasma and the deviation from adiabaticity of a flow due to some kind of heating–cooling function. It also...
-
Seasonal contributions of nutrients from small urban and agricultural watersheds in northern Poland
PublicationDiffuse sources of pollution like agricultural or urban runoff are important factors in determining the quality of surface waters, although they are more difficult to monitor thanpointsources.Theobjectiveofourstudywastoverifyassumptionsthattheinflow from agricultural nutrient sources is higher than from urbanized ones. It has been done by comparing the nutrients and organic matter concentrations and loads for three small streams...
-
Transport of dangerous goods by rail, and threats to the subsoil of the railway surface in the event of a disaster
PublicationIn Poland, in 2020, the mass of dangerous goods (loads) transported by rail was 26 151.06 thousand tone. This translated into the performance of 8 899 691.89 thousand tone - km of transport performance. In 2020, these figures accounted for 11.72% of the weight of goods transported by rail. The situation is similar in other countries around the world. With such a large volume of transport of dangerous...
-
Bitumen Aging—Laboratory Simulation Methods Used in Practice and Selected Directions of Research on New Methods
PublicationChanges in the properties of bitumen binders that occur as a result of aging have a huge impact on the durability of products produced from them. In particular, asphalt pavements, which constitute the most common use of petroleum bitumen, are susceptible to damage resulting from the increasing stiffness of the bitumen during its life cycle. Increased stiffness of asphalt pavements reduces the pavement resistance to low-temperature...
-
Improving operating efficiency of a gas turboset via cooperation with an absorption refrigerating machine
PublicationThe analysis of increase of ambient air temperature entering the compressor on reduction in power output from the turbine and increase fuel use was conduced. For medium size gas turbine operates in winter and summer conditions elementary power and economical values was calculated. Conditions of the determination of turbine inlet air cooling solution (using thermal storage for reduce equipment size) are presented
-
Investigation of rotational state-changing collisions of C2N− ions with helium
PublicationThe cross sections for rotational inelastic collisions between atoms and a molecular anion can be very large, if the anion has a dipole moment. This makes molecular anions very efficient in cooling atomic gases. We address rotational inelastic collisions of Helium atoms with the molecular anion C2N–. Here we present preliminary calculations of the potential energy surface.
-
Wpływ przechyłki na zjawisko postępowania zużycia bocznego szyn kolejowych w łukach poziomych
PublicationDegradacja elementów nawierzchni kolejowej jest zagadnieniem bardzo złożonym, w które uwikłane jest wiele czynników związanych między innymi z układem geometrycznym toru kolejowego, właściwościami trybologicznymi poszczególnych elementów nawierzchni, jak również z parametrami podłoża gruntowego, a także z właściwościami samych pojazdów szynowych. W artykule omówiono jeden z powyższych problemów, tj. wpływ ukształtowania toru kolejowego...
-
Beliefs about psychological help among firemen
PublicationThe aim of this study was to identify beliefs and perceived barriers in psychological help. Findings: 1. Occupational stress and participation in traumatic rescue actions was related with negative beliefs. 2. Firemen were afraid of a commader's reaction. 3. Avoidance coping accounts for fear about stigmatization.
-
Unsupervised Learning for Biomechanical Data Using Self-organising Maps, an Approach for Temporomandibular Joint Analysis
PublicationWe proposed to apply a specific machine learning technique called Self-Organising Maps (SOM) to identify similarities in the performance of muscles around human temporomandibular joint (TMJ). The performance was assessed by measuring muscle activation with the use of surface electromyography (sEMG). SOM algorithm used in the study was able to find clusters of data in sEMG test results. The SOM analysis was based on processed sEMG...
-
Determination of Earth Pressure and Displacement of the Retaining Structure According to the Eurocode 7-1
PublicationComparative analysis of standard guidelines and findings given in EC7-1 and in Polish Standard PN-83/B-03010. Discussed guidelines concerning active and passive earth pressure as well as at rest pressure state. Wall displacement causing limit states of earth pressure and resistance. Interactive assumptions concerning intermediate earth pressure and resistance values. Conclusions and final remarks.
-
Dual polarization antennas for UHF RFID readers
PublicationThis paper presents various concepts of switching polarization in patch antenna dedicated for UHF RFID readers. Proposed designs allow for switching between linear and circular polarization. The first design does not require electronic switching as the polarization can be changed by choosing one of two available feeding terminals. Two remaining designs use PIN diode or FET SPDT switch.
-
Weldability of high strength steels in wet welding conditions
PublicationIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...
-
Selected Features of Dynamic Voting
PublicationIn multi-agent systems composed of autonomous agents with local knowledge, it is often desirable to aggregate their knowledge in order to make an educated decision. One of the methods of agreeing to a common decision is voting. A new history-based dynamic weight protocol allows for identification of the agents which contribute to the correct system decision. The main advantage of this approach, compared to static weighted system...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublicationThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Slurry Surfacing Mixes on the Basis of Bitumen Modified with Phenol-Cresol-Formaldehyde Resin
PublicationSlow-breaking monophase cationic bitumen emulsions have been produced on the basis of bitumen modified with phenol-cresol-formaldehyde resin (PhCR-F). Bitumen emulsions were used as a binder for thin-layer coatings with slurry surfacing mixes (SSM). Physical and technical parameters of modified and unmodified emulsions were determined and analyzed. The optimal compositions of SSM were selected according to the breaking criterion....
-
Extending transition curve in analytical design method
PublicationThe paper presents the problem of extending the transitional curves, using for this purpose an analytical design method. The basis for the analysis of numerical calculations were carried out for a wide set of parameters characterizing the standard geometric system. We considered an importance of the size of radius of the circular arc and return angle of route on the obtained results after the formulation of appropriate theoretical...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublicationThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublicationCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATIONS OF CONCRETE BEHAVIOUR AT MESO-LEVEL DURING QUASI-STATIC SPLITTING TENSION
PublicationThe paper describes experimental and numerical results of quasi-static splitting tensile tests on concrete specimens at meso-scale level. The loading strip was made of plywood or steel. Fracture in concrete was detected at the aggregate level by means of three non-destructive methods: 3D x-ray micro-computed tomography, 2D scanning electron microscope and manual 2D digital microscope. The discrete element method was used to directly...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
MARITIME LASER SCANNING AS THE SOURCE FOR SPATIAL DATA
PublicationThe rapid development of scanning technology, especially mobile scanning, gives the possibility to collect spatial data coming from maritime measurement platforms and autonomous manned or unmanned vehicles. Presented solution is derived from the mobile scanning. However we should keep in mind that the specificity of laser scanning at sea and processing collected data should be in the form acceptable in Geographical Information...
-
Multivariate Statistical Analysis for Mutual Dependence Assessment of Selected Polyphenols, Organic Acids and Metals in Cool-Climate Wines
PublicationPolyphenols, organic acids and metal ions are an important group of compounds that affect the human health and quality of food and beverage products, including wines. It is known that a specific correlation between these groups exist. While wines coming from the New World and the Old World countries are extensively studied, wines coming from cool-climate countries are rarely discussed in the literature. One of the goals of this...
-
Electro-chemo-mechanical properties in nanostructured Ca-doped ceria (CDC) by field assisted sintering
PublicationRecent investigations have shown that highly oxygen defective cerium oxides generate non-classical electrostriction that is superior to lead-based ferroelectrics. In this work, we report the effect of field-assisted spark plasma sintering (SPS) on electro-chemo-mechanical properties of calcium doped ceria (CDC). Nanometric powders of Ca.10 nm are rapidly consolidated to form polycrystalline nanostructures with a high degree of...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-002)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-Con)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-004)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-006)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Application of a catalytic combustion sensor (Pellistor) for the monitoring of the explosiveness of a hydrogen-air mixture in the upper explosive limit range
PublicationA new technique is presented for continuous measurements of hydrogen contamination by air in the upper explosive limit range. It is based on the application of a catalytic combustion sensor placed in a cell through which the tested sample passes. The air content is the function of the quantity of formed heat during catalytic combustion of hydrogen inside the sensor. There is the possibility of using the method in industrial installations...
-
Metodyka projektowania i eksploatacji dróg szynowych z wykorzystaniem mobilnych pomiarów satelitarnych
PublicationW pracy zostały przedstawione aplikacyjne możliwości metody mobilnych pomiarów satelitarnych w projektowaniu i eksploatacji dróg szynowych. Pokazano wizualizację położenia toru kolejowego, omówiono sposoby oceny odcinków prostych toru i odcinków położonych w łuku oraz tworzenie poligonu kierunków głównych trasy. Szczególną uwagę poświęcono opracowanej analitycznej metodzie projektowania, omawiając jej algorytmy obliczeniowe: projektowania...
-
Justyna Zander dr inż.
People -
Quasi-controlled Experimentations on the Impact of AOP on Software Comprehensibility
PublicationAspect-oriented programming (AOP) emerged as a paradigm to modularize the concerns that lead to interwoven code if implemented using traditional programming techniques. Unfortunately, the new constructs introduced by aspect-oriented (AO) languages result in both: (1) obstacles in modular reasoning, and (2) high coupling between aspects and the augmented modules. There have been numerous attempts to tackle these issues, but none...
-
Towards a modification of a regulatory framework aiming at bunker oil spill prevention from ships - A design aspect of bunker tanks vents location guided by CFD simulations
PublicationAlthough accidental bunker oil spills at seaway are relatively rare events, they can be pose real threat to the natural marine environment. One of the reasons for the bunker spill to occur is a design failure; one of the ways it can demonstrate is an improper location or height of vent heads, leading to a bunker oil discharge during heavy rolling, due to sloshing phenomenon. Design of a ship and her systems is guided by various...
-
Pedestrian Safety in Road Traffic in Poland
PublicationEvery third road accident in Poland involves a pedestrian as a participant or, most of the time, a casualty. Pedestrian accidents are usually the result of complex situations and the outcome of a number of factors related to driver and pedestrian behaviour and road infrastructure. Safety depends largely on how well the traffic condition is perceived and on visibility in traffic. The paper presents the results of analyses of methodologies...
-
Mury oporowe z gruntu zbrojonego z przekładkami z keramzytu
PublicationW czerwcu 2019 r. nastąpiło otwarcie nowo budowanego wiaduktu na ulicy Drwęckiej w Ostródzie, który zastąpił jeden z trzech przejazdów kolejowo-drogowych znajdujących się w centrum miasta. Zakończenie budowy bezkolizyjnego przejazdu nad torami kolejowymi pozwoliło na bezpieczne oraz szybkie połączenie północnej i południowej części Ostródy. Zastosowanie materacy z keramzytu w konstrukcji z gruntu zbrojonego.
-
Automation of ship and control
PublicationSummaryThe article presents the problem of automation of ship and control. This paper will discuss the basic tasks of the track ship control, collision avoidance and automatic dynamic positioning. The following subjects will be presented: the general structure of the ship's control, methods and control algorithms for the above mentioned tasks..StreszczenieArtykuł przedstawia zagadnienia automatyzacji i sterowania statkiem. W pracy...
-
Optimal Rotating Receiver Angles Estimation for Multicoil Dynamic Wireless Power Transfer
PublicationThis study proposed an approach to dynamic wireless charging that uses a rotating receiver coil. Our simulation study focused on the verification of a novel way of increasing the coupling coefficient and power transfer stability by following the flux of the transmitting coils. To obtain the highest possible coupling by means of the FEM analysis, we studied the optimization of the trajectory of the angular velocity of the rotating...
-
Analyzing the Geometry of the Turnouts and Their Adjustment Basing on the Tacheometer Measurements
PublicationThe article presents the results of tacheometric measurements of a station throat, as well as the method of data preparation and analysis. The calculations covered the verification of the geometry and the location of railway turnouts and crossings. The analyses were performed for the selected parameters of the turnout geometry, including their lengths and track gauge in main sections. In addition, the data were analyzed to confirm...
-
Simple gait parameterization and 3D animation for anonymous visual monitoring based on augmented reality
PublicationThe article presents a method for video anonymization and replacing real human silhouettes with virtual 3D figures rendered on a screen. Video stream is processed to detect and to track objects, whereas anonymization stage employs animating avatars accordingly to behavior of detected persons. Location, movement speed, direction, and person height are taken into account during animation and rendering phases. This approach requires...
-
Ekonomiczne aspekty strategii utrzymania torów kolejowych
PublicationW ostatnich lata coraz więcej uwagi poświęca się analizie kosztów cyklu życia (Life Cycle Cost - LCC) w zakresie planowania strategii utrzymania infrastruktury kolejowej. Większość prac ogranicza się jednak do kosztów bezpośrednich (planowanych), takich jak budowy, konserwacji, odnowienia i utylizacji. Takie podejście prowadzi do niedoszacowania kosztów wynikających z niskiej jakości geometrii toru. W artykule przedstawiona została...
-
Projektowanie układów geometrycznych toru z zastosowaniem optymalizacji wielokryterialnej
PublicationW pracy przedstawiono metodę projektowania odcinków trasy kolejowej położonych w łuku, dostosowaną do techniki mobilnych pomiarów satelitarnych. Rozwiązanie problemu projektowego wykorzystuje zapis matematyczny i polega na wyznaczeniu uniwersalnych równań opisujących całość układu geometrycznego. Odbywa się to sekwencyjnie, obejmując kolejne fragmenty tegoż układu. Procedura projektowania ma charakter uniwersalny, gdyż w ogólnym...