Search
Filters
total: 2326
displaying 1000 best results Help
Search results for: OPERATOR HISTEREZOWY
-
Emergency condition of the ceramic facade of a residential building
PublicationThe paper presents a description of the technical condition of the ceramic cladding of a residential building, the technical condition of which deteriorated significantly after only a few years of operation. The analysis of the influence of the applied design and working solutions on the façade failure frequency was analyzed. The article presents a conceptual solution to bring the building to the proper technical condition in terms...
-
Design and investigations of the ethanol microturbine
PublicationThe paper presents the results of the design analysis and experimental investigations of the microturbine set consisting of the microturbine with partial admission and permanent magnet generator. The microturbine was designed for operation with the vapour of ethanol as a working fluid. Microturbine unit was tested for different parameters of the working fluid and varying the electrical load. The examples and the comparison between...
-
Improving operating efficiency of a gas turboset via cooperation with an absorption refrigerating machine
PublicationThe analysis of increase of ambient air temperature entering the compressor on reduction in power output from the turbine and increase fuel use was conduced. For medium size gas turbine operates in winter and summer conditions elementary power and economical values was calculated. Conditions of the determination of turbine inlet air cooling solution (using thermal storage for reduce equipment size) are presented
-
Immunity of residual current devices to the impulse leakage current in circuits with variable speed drives
PublicationThis paper concerns reliability of supply in variable speed drive circuits with residual current devices. During normal operation of these circuits high value of leakage current causes unwanted tripping of residual current devices. Immunity of residual current devices to the impulse leakage current should be evaluated. The system for testing of residual current devices and results of the test are presented
-
Wpływ strat mechanicznych w siłowniku teleskopowym zespołu zagęszczającego w pojeździe do usuwania odpadów z pojemników na skuteczność prasowania odpadów
PublicationHydraulic telescopic cylinders are used to power the moving wall of rear loader garbage trucks equipped with the traditional "sweep and slide" system. As the garbage compression force is directly dependent on the resistance force of the moving wall, losses in the hydraulic telescopic cylinder influence the compaction process. Taking them into account in the control system may improve the operation of the compaction...
-
The secure transmission protocol of sensor Ad Hoc network
PublicationThe paper presents a secure protocol of radio Ad Hoc sensor network. This network operates based on TDMA multiple access method. Transmission rate on the radio channel is 57.6 kbps. The paper presents the construction of frames, types of packets and procedures for the authentication, assignment of time slots available to the node, releasing assigned slots and slots assignment conflict detection.
-
Active feedback noise control in the presence of impulsive disturbances
PublicationThe problem of active feedback control of a narrowband acoustic noise in the presence of impulsive disturbances is considered. It is shown that, when integrated with appropriately designed outlier detector, the proposed earlier feedback control algorithm called SONIC is capable of isolating and rejecting noise pulses. According to our tests this guarantees stable and reliable operation of the closed-loop noise cancelling...
-
Thermal and Electrodynamic Risk of Residual Current Devices in the Case of Back-Up Protection by Overcurrent Circuit Breakers
PublicationResidual current operated circuit breakers without integral overcurrent protection should be back-up protected. As back-up protection devices, overcurrent circuit breakers are used. The maximum let-through energy and let-through current of the overcurrent devices were evaluated under laboratory conditions. The thermal and electrodynamic risk of residual current devices was analyzed.
-
Emergency condition of the ceramic facade of a residential building
PublicationThe paper presents a description of the technical condition of the ceramic cladding of a residential building, the technical condition of which deteriorated significantly after only a few years of operation. The analysis of the influence of the applied design and working solutions on the façade failure frequency was analyzed. The article presents a conceptual solution to bring the building to the proper technical condition in terms...
-
An Impact of Environmental Disturbances on Combined Cycle Power Plant Control
PublicationCombined cycle power plants operate at thermal efficiency approaching 60 percent. In the same time their performance presents several problems that have to be addressed. E.g. gas turbines are very sensitive to backpressure exerted on them by the heat recovery steam generators as well as to ambient pressure and temperature.
-
The aggregation of objects representing Katowice district buildings - scale 1:25000
Open Research DataThe process of automatic generalization is one of the elements of spatial data preparation for the purpose of creating digital cartographic studies. The presented data include a part of the process of generalization of building groups obtained from the national geodesy and cartography resource from BDOT10k (10k topographic database) [1].
-
The aggregation of objects representing Katowice district buildings - scale 1:10000
Open Research DataThe process of automatic generalization is one of the elements of spatial data preparation for the purpose of creating digital cartographic studies. The presented data include a part of the process of generalization of building groups obtained from the national geodesy and cartography resource from BDOT10k (10k topographic database) [1].
-
Wojciech Chrzanowski dr hab. inż.
PeopleWojciech Chrzanowski was born in 1952 in Toruń. He completed his studies in Chemical Technology in 1975, getting his MSc in Inorganic Technology (specialty: Anti-Corrosion Protection) At the Faculty of Chemistry, Gdańsk University of Technology (with distinction). Later this year he was employed in the Department of Analytical Chemistry of then Institute of Chemical Engineering and Measuring Techniques, initially as a technical...
-
Optical Parameters Stability Over Time of Porous Phantoms Mimicking Tissues
Open Research DataOptical phantoms are used to validate optical measurement methods. The stability of their optical parameters over time allows them to be used and stored over long-term periods while maintaining their optical parameters. The aim of the presented research was to investigate the stability of fabricated porous phantoms, which can be used as a lung phantom...
-
Mn-Co nanofilms on nickel foam measured by XPS mehod
Open Research DataManganium-Cobaltium based thin films were electrochemically deposited on a Ni based subsrates in a one-step process at −1.1 V vs. Ag/AgCl in an aqueous solution of differently concentrated Mn(NO3)2·4H2O and Co(NO3)2·6H2O with the deposition time limited by charges of 60, 120, and 200 mC at 25 °C. The concentration ratios of Mn(NO3)2·4H2O to Co(NO3)2·6H2O...
-
Tracing of dynamic objects in distributed interactive simulation systems
PublicationDistributed interactive simulation systems require integration of several areas of computer science and applied mathematics to enable each individual simulation object to visualize effectively dynamic states of other objects. Objects are unpredictable,i.e., controlled by their local operators, and are remote, i.e., must rely on some transmission media to visualize dynamic scene from their local perspectives. The paper...
-
Route vertical alignment design in the process of its regulation
PublicationW monografii przedstawiona została metoda opracowania projektu niwelety toru kolejowego na podstawie pomierzonych nierówności pionowych oraz praktyczny przykład jej zastosowania w procesie utrzymaniu dróg szynowych, a w szczególności w projektowaniu robót związanych z regulacją osi toru. Wykonany w ten sposób profil istniejącej linii kolejowej jest podstawą do obliczenia wartości podnoszeń toru. Wartości te nanosi się w terenie...
-
Assessment of performance of unmanned maritime vehicles (USV, UUV, AUV) by CFD and MES investigation, PG_00053662
e-Learning CoursesThe course entitled "Assessment of Performance of Unmanned Maritime Vehicles" consists of the following problems to be discussed during the lectures (W): - major areas of application of UMV unmanned maritime vehicles, - sea environment, - types of UMV vehicles, - parameters, characteristics and features of UMV vehicles, - research, design, construction, implementation and operation of UMV vehicles, - systems of UMV vehicles...
-
Blackout initial disturbances in electric Power System searching
PublicationThe paper contains short survey of the blackouts that took place in the last few years. The sources and initial disturbances are discussed. The typical scenario of the disturbance, leading to blackout in the electrical power system are presented.Next, models of a power system eligible to considered topic are discussed. Finally the algorithm of the blackout initial disturbances in power system searching is presented.The consideration...
-
Prospects of ionic liquids application in electronic and bioelectronic nose instruments
PublicationThis paper addresses the problem of application of ionic liquids to chemical sensors and biosensors being an integral part of the electronic and bioelectronic-type instruments. The design and principle of operation of the electronic and bioelectronic noses are compared. Both the benefits and shortcomings of the application of ionic liquids in these type of instruments are described. The prospects of the development and application...
-
Measurement system based on USB Z-Wave controller
PublicationA wireless measurement system based on the Z-Wave standard is presented in this paper. The system is composed of a U SB Z-Stick Gen5 controller connected to a Personal Computer and a Fibaro controller FGRGBWM-441. Operation of the system is controlled by software written in C++ using OpenZWave library. Some metrological aspects of the system are evaluated: accuracy, linearity, resolution and frequency of voltage measurements.
-
Numerical methods for systems of nonlinear differential functional equations
PublicationPraca dotyczy zagadnień początkowo brzegowych dla nieliniowych układów różniczkowo funkcyjnych. Rozważana jest aproksymacja rozwiązań rozważanego problemu różniczkowo funkcyjnego przez rozwiązania odpowiedniego problemu różnicowego. W pracy analizowana jest zbieżność prezentowanych metod. Dowód zbieżności opiera się na technice porównawczej z nieliniowym oszacowaniem typu Perron'a dla danych operatorów.
-
Reliable renewable energy – application of electrochemical capacitors for electrical energy storage
PublicationThis paper presents electrical energy storage devices such as electrochemical capacitors, their principle of operation and electrode materials most commonly used in their manufacturing technology. Moreover, our research on development of new nanocomposite materials based on multi-walled carbon nanotubes and conducting polymer is shown. Additionally, the possibility and advantages of application of supercapacitors for accumulation...
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublicationThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
Compact satellite hydraulic unit
PublicationThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
Gate Driver with Overcurrent Protection Circuit for GaN Transistors
PublicationThe improvement of the gate driver for GaN transistor is presented in this paper. The proposed topology contains the overcurrent protectionwith the two-stage turning off and independent control of turn on and off time of the GaN transistor. The operation of driver and its application in thehalf-bridge converter are described using both simulation and prototype measurements. The overcurrent protection was tested in Double Pulse...
-
ADDPRIV Automatic Data relevancy Discrimination for a PRIVacy-sensitive video surveillance
ProjectsProject realized in Faculty of Electronics, Telecommunications and Informatics according to 261653 agreement from 2011-01-27
-
Voltage Control of a Stand-Alone Multiphase Doubly Fed Induction Generator
PublicationThis article presents a multiphase doubly fed induction generator (MDFIG) with a dedicated and unique control algorithm in a stand-alone wind energy conversion system. The algorithm has been developed and elaborated in the case of different emergency modes. Compared with the traditional double-fed induction generator, the MDFIG has increased reliability, reduced current level per phase, and low rotor harmonic currents. The control...
-
The Design Development of the Sliding Table Saw Towards Improving Its Dynamic Properties
PublicationCutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Sensorless Fault Detection of Induction Motor with Inverter Output Filter
PublicationThe paper presents the problem of monitoring and fault detection of a sensorless voltage inverter fed squirrel cage induction motor with LC filter. The detection is based on load torque estimation of the investigated torque transmission system. The load torque is calculated besides the computation of other variables that are mandatory for sensorless drive operation such as rotor flux and speed. The implemented LC filter smooths...
-
NEW DESIGNS OF MAGNETIC FLUID SEALS FOR RECIPROCATING MOTION
PublicationT he operating conditions of magnetic fluid seals during reciprocating motion are so different from those observed in rotating motion that the use of their conventional structures for reciprocating motion seals yields no good results. The analysis of the sealing mechanism of magnetic fluid seals in reciprocating motion shows that the operation of these seals is affected by the carry-over phenomenon and magnetic fluid...
-
Microfluidic SIW-Based Tunable Self-Diplexing Antenna for Sub-6 GHz Band Applications
PublicationThis work introduces a novel frequency tunable self-diplexing antenna (SDA) design based on substrate integrated waveguide (SIW) technology. A modified A-shaped slot is employed on the cavity’s top plane, which is excited by two independent 50 Ω microstrip feed lines to operate at each resonant frequency. The frequency flexibility of the proposed antenna allows for fine-tuning at each resonance frequency. The frequency flexibility...
-
Jakość usług w sieciach osiedlowych
PublicationW pracy dokonano charakterystyki sieci osiedlowych, szczególny nacisk położono na aspekty związane z jakością oraz poziomem dostępności świadczonych usług. Autorzy, na podstawie własnego doświadczenia zawodowego, zaproponowali szereg rozwiązań programowych oraz sprzętowych opartych na standardach IEEE i IETF, pozwalających na podniesienie poziomu usług świadczonych przez operatorów osiedlowych.
-
Research and analysis of high-speed data transmission radio link designed for maritime environment
PublicationIn these article the realization of digital radio link for high-speed data transmission was presented. Its concept and practical realization, using USRP devices from National Instruments, were described. Developed software for generation and reception of digital signals in baseband, including description of modulation types, and time and frequency synchronization mechanisms, was presented. Moreover, an operation of designed radio...
-
Research and Analysis of High-Speed Data Transmission Radio Link Designed for Maritime Environment
PublicationIn these article, the realization of digital radio link for high-speed data transmission was presented. Its concept and practical realization, using USRP devices from National Instruments, were described. Developed software for generation and reception of digital signals in baseband, including description of modulation types, and time and frequency synchronization mechanisms, was presented. Moreover, an operation of designed radio...
-
Alternative Energy: Photovoltaic Solar Cells
PublicationSolar radiation is a fuel for photovoltaic cells and modules, which are a source of electric energy. Viable solar technologies that have been developed in the past are starting to be adopted on a broader and more meaningful global scale across different sectors with ever-increasing market penetration. In this entry, a brief overview of the material properties relevant to solar cell operation, the structure of the solar cell, and electrical...
-
Application of electrochemical sensors and sensor matrixes for measurement of odorous chemical compounds
PublicationIn this paper describes the principle of operation of the electrochemical sensors and the sensor matrixes comprised of electrochemical sensors intended for measurement of odorous compounds. Critical comparison of these sensors’ advantages and disadvantages has been made. The fields of economy contributing to release of odours and the potential sources of their emission have been identified. Commercially available electrochemical...
-
Free-surface elevation in open vortex flow controls
PublicationRotational form of fluid motion is complex, but very important in science and technology. The paper is devoted to the hydraulic mechanism of flow in open vortex flow controls, or regulators. The velocity field was described by the kinematic model, and intensity of rotation - by means of the energy balance between the input and dissipation. In consequence some algebraic expresions were obtained, which can be useful in approximated...
-
Patch size setup and performance/cost trade-offs in multi-objective antenna optimization using domain patching technique
PublicationA numerical study concerning multi-objective optimization of antenna structures using sequential domain patching (SDP) technique has been presented. We investigate the effect of various setups of the patch size on the operation of the SDP algorithm and possible trade-offs concerning the quality of the Pareto set found by SDP and the computational cost of the optimization process. Our considerations are illustrated using a UWB monopole...
-
Effect of long term service at elevated temperatures on mechanical properties of Manaurite XM reformer tubes
PublicationMicrostructure transformations occur in the Manaurite XM cast steel tubes during long-term operation in the reformer furnace were revealed and described. The rela tionship between mechanical properties, an increase of internal diameter of the tube and microstructure degradation is discussed. Static tensile test was performed on two types of samples with different shapes. It has been shown differences in the results of tests...
-
Transmission protocol simulation framework for the resource-constrained sensor network
PublicationIn this paper the simulation framework for simulation of the sensor network protocol is presented. The framework enables the simultaneous development of the sensor network software and the protocol for the wireless data transmission. The advantage of using the framework is the convergence of the simulation with the real software, because the same software is used in real sensor network nodes and in the simulation framework. The...
-
Diagnostics of thermal processes in antenna systems of broadcast stations
PublicationDiagnostics is an important element associated with the operation of a radio antenna systems, allowing earlier detection of potential damage. Thermography is one of the diagnostic tools, which allows for non-invasive assessment of technical condition. It brings together both financial savings associated with the removal of the damage and the potential effects caused by it. The article presents an example of using a thermal imaging...
-
A New Method of Noncausal Identification of Time-varying Systems
PublicationThe paper shows that the problem of noncausal identification of a time-varying FIR (finite impulse response) sys- tem can be reformulated, and solved, as a problem of smoothing of the preestimated parameter trajectories. Characteristics of the smoothing filter should be chosen so as to provide the best trade- off between the bias and variance of the resulting estimates. It is shown that optimization of the smoothing operation can...
-
Analytical design of stable delta-domain generalized predictive control
PublicationPraca dotyczy analitycznej metody projektowania układów sterowania skalarnymi (SISO) obiektami czasu ciągłego według strategii uogólnionego sterowania predykcyjnego (GPC) w oparciu o dyskretnoczasowe modele takich obiektów. Założono wykorzystanie numeryczne odpornych modeli opartych o tak zwany operator delta. Przyjmując kwadratowy funkcjonał kosztów, w którym prognozowany przebieg przyszłego wyjścia sterowanego obiektu porównywany...
-
Wavepacket of the Universe and its Spreading
PublicationWavepackets in quantum mechanics spread and the Universe in cosmology expands. We discuss a formalism where the two effects can be unified. The basic assumption is that the Universe is determined by a unitarily evolving wavepacket defined on space-time. Space-time is static but the Universe is dynamic. Spreading analogous to expansion known from observational cosmology is obtained if one regards time evolution as a dynamical process...
-
Decisional DNA (DDNA) Based Machine Monitoring and Total Productive Maintenance in Industry 4.0 Framework
PublicationThe entire manufacturing spectrum is transforming with the advent of Industry 4.0. The features of Set of Experience Knowledge Structure (SOEKS) and Decisional DNA (DDNA) were utilized for developing Virtual Engineering Objects (VEO), Virtual Engineering Process (VEP) and Virtual Engineering Factory (VEF), which in turn facilitate the creation of smart factories. In this study, DDNA based Machine Monitoring for Total Maintenance...
-
MOŻLIWOŚCI IDENTYFIKACJI STANU TECHNICZNEGO WARSTW ŚLIZGOWYCH ŁOżYSK SILNIKÓW SPALINOWYCH O ZAPŁONIE SAMOCZYNNYM W PRZYPADKU WYKORZYSTANIA EMISji AKUSTYCZNEJ JAKO SYGNAŁU DIAGNOSTYCZNEGO
PublicationW artykule zaprezentowano wyniki badań wielowarstwowych panwi łożysk ślizgowych silników tłokowych. Scharakteryzowano własności obciążeń tego rodzaju panwi oraz ich zużycia szczególnie zmęczeniowego i ściernego. Wykazano przydatność emisji akustycznej jako sygnału diagnostycznego do ujawniania zużycia powłok ślizgowych i zaporowych. Przedstawiono wyniki pomiarów parametrów emisji akustycznej, wykonanych za pomocą 12- kanałowej...
-
Smart Karyotyping Image Selection Based on Commonsense Knowledge Reasoning
PublicationKaryotyping requires chromosome instances to be segmented and classified from the metaphase images. One of the difficulties in chromosome segmentation is that the chromosomes are randomly positioned in the image, and there is a great chance for chromosomes to be touched or overlap with others. It is always much easier for operators and automatic programs to tackle images without overlapping chromosomes than ones with largely overlapped...
-
Regulacja napięć i mocy biernej. Realizacja hierarchicznej struktury sterowania w KSE
PublicationPrzedstawiono program przedsięwzięć technicznych, organizacyjnych i prawnych związanych z wdrażaniem autorskiej koncepcji sterowania poziomami napięć i rozpływem mocy biernej w systemie elektroenergetycznym, powstałej w związku z restrukturyzacją elektroenergetyki. Koncepcja sterowania i program są rezultatem pracy badawczej realizowanej w Katedrze Elektroenergetyki PG dla Polskich Sieci Elektroenergetycznych S.A. W referacie przedstawiono...