Filtry
wszystkich: 274
wybranych: 250
Wyniki wyszukiwania dla: VOLUMETRIC LOSSES, SATELLITE PUMP, WATER, OIL
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Research on causes of corrosion in the municipal water supply system
PublikacjaThis paper presents results of failure analysis study to characterize the corrosion damage that occurred in the water supply system in Krakow. This analysis includes: electrochemical noise, linear polarization and resistometric measurements. Water aggressiveness of four water intakes was defined using Langelier and Ryznar indices. Results from this indices did not reveal the causes of considerable corrosion losses in water systems....
-
One-Step Synthesis of W/O and O/W Emulsifiers in the Presence of Surface Active Agents
PublikacjaThe main goal of this study was to describe the method of the synthesis of the dodecyl-, tetradecyl-, hexadecyl- and octadecyl-propylene glycol emulsifiers in the presence of selected anionic and nonionic surfactants. Acyl propylene glycol emulsifiers were produced by esterification of propane-1,2-diol (propylene glycol, PG) with C12:0-C18:0 fatty acids in the presence of anionic sodium dodecyl sulfate (SDS) and nonionic-poly(ethylene...
-
Funkcjonowanie zespołów napędu hydraulicznego maszyn w niskich temperaturach otoczenia
PublikacjaW pracy przedstawiono cztery warianty klasyfikacji rozruchów oziębionego napędu hydraulicznego. Pierwsza sytuacja dotyczy zagadnienia, w którym wszystkie zespoły układu napędowego wraz z olejem mają taką samą niską temperaturę podczas rozruchu. Pozostałe warianty odnoszą się do rozruchu w warunkach szoku termicznego wywołanych zasilaniem ciepłym czynnikiem roboczym oziębionych zespołów hydraulicznych. Rozruch zespołów...
-
Polyester-urethanes modified with gelatine for tissue scaffolds
PublikacjaNovel aliphatic PU foams, modified with gelatine, were obtained in a one-step polymerization process. Hard segments were obtained from 1,6-hexamethylene diisocyanate (HDI) and chain extenders 1,4-butanediol (BDO) or 2-(2-(2-hydroxyethoxy)ethoxy)ethanol (TG), soft segments were obtained from poly(ethylene-buthylene adipate) (EBO) polyol. We examined the PU foams for their sorption capability in canola oil, saline (0.9% NaCl water...
-
Początek Gdyńskiego Systemu Wodociągowego Planowanie i budowa lokalnego układu wodociągowego na Kępie Oksywskiej (1929 – 1932. Część II.
PublikacjaUdokumentowanie procesu inwestycyjnego przekształcenia wodociągu wiejskiego w miejski układ wodociągowy na podstawie analizy materiałów źródłowych. Ustalenie hydrogeologicznych uwarunkowań decyzji o lokalizacji ujęcia wody „Oksywie”. Identyfikacja parametrów konstrukcyjnych i kosztów budowy trzech budynków na ujęciu wody: mieszkalnego, stacji pomp i odżelaziania wody. Odtworzenie przebiegu budowy struktury sieci wodociągowej w...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublikacjaDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Water Solubilization Using Nonionic Surfactants from Renewable Sources in Microemulsion Systems
PublikacjaIn this study the effect of temperature, NaCl andoils (hydrocarbons: C8-C16) on the formation and solubilizationcapacity of the systems of oil/monoacylglycerols(MAG):ethoxylated fatty alcohols (CEO20)/propylene glycol(PG)/water was investigated. The effects of the surfactantmixture on the phase behavior and the concentration ofwater or oil in the systems were studied at three temperatures(50, 55, 60 C) and with varied NaCl solutions...
-
Two Time-Scale Hierarchical Control of Integrated Quantity and Quality in Drinking Water Distribution Systems
PublikacjaThe paper considers a feedback optimising control of drinking water distribution systems (DWDS). Although the optimised pump and valves scheduling and disinfectant injection control attracted considerable attention over last two decades most of the contributions were limited to an open-loop optimisation repetitively performed during the DWDS operation. Also, while a strong interaction between the water quantity and quality exists...
-
Effect of different crystalline structures on W/O and O/W/O wax emulsion stability
PublikacjatThe possibility of emulsion stabilization using mineral and vegetable wax particles only (without sur-factant) was investigated. Mineral waxes, paraffin wax and ceresin, and a vegetable wax, carnauba wax,were used. The content of the wax particles and the water to oil proportion were found crucial for thestability of all emulsions. Some emulsions were also produced with a liquid wax (i.e. jojoba oil). Themultiple light scattering...
-
DETERMINATION OF THE EFFECT OF ENVIRONMENTAL FACTORS ON THE CORROSION OF WATER DISTRIBUTION SYSTEM BASED ON ANALYSIS OF ON-LINE CORROSION MONITORING RESULTS
PublikacjaCorrosion of water distribution system is a significant issue causing problems with quality, safety and continuity of distribution. The changes of corrosion rates of the water distribution systems in Cracow made of carbon steel were investigated by analysis of online corrosion monitoring system results. Corrosion rates were determined using the linear polarization method. The impact of rain, temperatures, conductivity, dissolved...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Effect of alkyl sulfate on the phase behavior of microemulsions stabilized with monoacylglycerols
PublikacjaIn this study the effect of an anionic surfactant (sodium dodecyl sulfate SDS) and oils (hydrocarbons: C12-C16) on the formation and phase behavior of the systems of oil/monoacylglycerols (MAG):SDS/propylene glycol/water has been investigated. The effects of the surfactant mixture on the phase behavior and the concentrationof water or oil in the systems were studied at three temperatures (50, 55, 60 C). Electrical conductivity...
-
Monitoring of lysozyme thermal denaturation by volumetric measurements and nanoDSF technique in the presence of N-butylurea
PublikacjaThe results of thermal studies of denaturation of hen egg white lysozyme (HEWL) in water and an aqueous solution of N-butylurea (BU) are presented. High-precision densimetric measurements were used to characterize and analyze the changes of the specific volume, v, during temperature elevation. The temperature of the midpoint of protein denaturation was also determined by nanoDSF technique (differential scanning fluorimetry). The...
-
The interaction parameters for solutions of n-butylurea in aqueous solutions of N-methylacetamide – The volumetric and compressibility studies between 288.15 K and 308.15 K
PublikacjaDensities and speed of sound were measured for solutions of n-butylurea in aqueous solution of Nmethylacetamide 2, 4, 6 and 8 (mol/kg) at T = (288.15, 298.15 and 308.15) K. From these data the apparent molar volumes, Vf, the apparent molar isentropic compressions, KSf, of the solute were determined. The concentration dependencies of the calculated quantities have been used to obtain the standard partial molar parameters. The latter...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublikacjaEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Propagation Characteristics of Partial Discharges in an Oil-Filled Power Transformer
PublikacjaPower transformers are among the most important assets in the power transmission and distribution grid. However, they suffer from degradation and possible faults causing major electrical and financial losses. Partial discharges (PDs) are used to identify the insulation health status and their degradation level. PDs are incipient, low-magnitude faults caused by localized dielectric breakdown. Those activities emit signals in many...
-
Natural radioactivity of solid and liquid phases from shale oil and gas prospection in Pomerania
PublikacjaIonizing radiation intensity data and estimation of equivalent absorbed dose from solid and liquid samples from prospection of shale gas and oil at selected sites in Pomerania are presented. Naturally occurring radioactive materials (NORM) are associated with geological formations or fluids and can be enhanced during oil and gas production. They appear in e.g. drilling cuttings, flow back water, produced water, scale and sludge....
-
Arterial cannula shape optimization by means of the rotational firefly algorithm
PublikacjaThe article presents global optimization results of arterial cannula shapes by means of the newly modified firefly algorithm. The search for the optimal arterial cannula shape is necessary in order to minimize losses and prepare the flow that leaves the circulatory support system of a ventricle (i.e. blood pump) before it reaches the heart. A modification of the standard firefly algorithm, the so-called rotational firefly algorithm,...
-
Mechanical characterization of a gravel column in a calibration chamber operating as a triaxial cell
PublikacjaA series of tests considering the behavior of gravel columns was performed. A segment of column with a height of 1 m and a diameter of 0.53 m was modelled in a calibration chamber used as a triaxial cell at three different lateral stress applied. The vertical load transferred on the column head was simulated with steady increase of water pressures in the upper and lower membranes. During the loading the volumetric changes in the...
-
Flow of liquid in flat gaps of the satellite motor working mechanism
PublikacjaThe article describes the methodology and results of investigations of the flow of oil and HFA-E emulsion in flat gaps of the working mechanism of a satellite motor. The flow of liquid in those gaps is turbulent and not fully developed. The article presents two methods of modelling this flow. Method I makes use of the Darcy-Weisbach formula, while Method II bases on the assumption that in the variable-length gaps the flow is turbulent...
-
The influence of Nigella sativa essential oil on proliferation, activation, and apoptosis of human T lymphocytes in vitro
PublikacjaIn previous work, we tested the immunomodulatory effect of Nigella sativa (NS) fatty oil. Our results demonstrated that unrefined, obtained by cold pressing black cumin seed oil inhibited lymphocytes’ proliferation and induced their apoptosis in a dose-dependent manner. In this study, we examined the immunomodulatory properties of essential oil (EO) obtained from the NS seeds by hydrodistillation and its two main constituents:...
-
Discussion of “Development of an Accurate Time integration Technique for the Assessment of Q-Based versus h-Based Formulations of the Diffusion Wave Equation for Flow Routing” by K. Hasanvand, M.R. Hashemi and M.J. Abedini
PublikacjaThe discusser read the original with great interest. It seems, however, that some aspects of the original paper need additional comments. The authors of the original paper discuss the accuracy of a numerical solution of the diffusion wave equation formulated with respect to different state variables. The analysis focuses on nonlinear equations in the form of a single transport equation with the discharge Q (volumetric flow rate)...
-
Hydration of aprotic donor solvents studied by means of FTIR spectroscopy
PublikacjaThe paper attempts to explain the mutual influence of nonpolar and electron-donor groups on solute hydration,the problem of big importance for biological aqueous systems. Aprotic organic solvents have been used asmodel solutes, differing in electron-donating power. Hydration of acetonitrile, acetone, 2-butanone, andtriethylamine has been studied by HDO and (partially) H2O spectra. The quantitative version of...
-
Distribution of volatile organohalogen compounds in petrochemical plant water streams
PublikacjaThe study assesses halogenated volatile organic compound concentrations in the water and wastewaterstreams of a petrochemical plant. Water samples were collected at 11 sampling points during 5 samplingcampaigns. The samples were collected from the oil dewaxing unit and in the wastewater treatmentplant. Dichloromethane and 1,2-dichloroethane were the most frequently determined compounds. Tetrachloroethenewas also detected at the...
-
Tryton Supercomputer Capabilities for Analysis of Massive Data Streams
PublikacjaThe recently deployed supercomputer Tryton, located in the Academic Computer Center of Gdansk University of Technology, provides great means for massive parallel processing. Moreover, the status of the Center as one of the main network nodes in the PIONIER network enables the fast and reliable transfer of data produced by miscellaneous devices scattered in the area of the whole country. The typical examples of such data are streams...
-
Environmental Impacts of Renewable Energy Technologies
PublikacjaNowadays, fossil fuels are the main sources energy from which electricity is obtained. But these sources will not last forever, so in due course renewable energies will have to replace them in this role. All energy sources have some impact on our environment. Fossil fuels — coal, oil, and natural gas — do substantially more harm than renewable energy sources by most measures, including air and water pollution, damage to public...
-
Application of Web-GIS and Geovisual Analytics to Monitoring of Seabed Evolution in South Baltic Sea Coastal Areas
PublikacjaRegular surveys of coastal zone seabed deliver important information about geomorphologic processes such as silting of waterways. The recent introduction of the Sentinel series of sensors has allowed for the use of satellite sensing for shallow bathymetry morphology monitoring. In this context, this article presents a dedicated Geographic Information System for Baltic Sea shallow water depth monitoring on the basis of Sentinel-2...
-
Pipeline System for Heat Transportation from Nuclear Power Plant – an Optimizing Approach
PublikacjaOver the last few years heat piping insulation technology and pump systems efficiency have been significantly improved. Reduced thermal losses encourage heat transportation over long distances. It provides an opportunity for increasing thermodynamic efficiency of Nuclear Power Plants (NPPs) that are often located in rural areas because of safety issues. It can be achieved by Combined Heat and Power (CHP) generation, as heat produced...
-
Validation of atmospheric aerosols parallel sampling in a multifold device
PublikacjaIn this work, particulate matter was collected using an active sampling system consisting of a PM10 (<10 μm) inlet coupled to a multifold device containing six channels, connected to a vacuum pump. Each channel was equipped with a filter holder fitted with adequately chosen filters. The system was fixed on a metallic structure, which was placed on the roof of the laboratory building, at the Faculty of Sciences, in Lisbon. Sampling...
-
A distillery by-product as an external carbon source for enhancing denitrification in mainstream and sidestream treatment processes
PublikacjaThe use of fusel oil as an 'alternative' carbon source for denitrification in the mainstream and sidestream treatment processes was studied. Research comprised two kinds of batch experiments as well as acclimation of process biomass to external carbon sources. In the conventional nitrate utilization rate (NUR) measurements (one-phase experiments with non-acclimated biomass), the NUR with fusel oil was 1.4-1.7 g N/(kg VSS•h which...
-
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublikacjaThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublikacjaJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...
-
Selected aspects of determining the reliability of the pump subsystems with redundancy, used in main engine auxiliary systems
PublikacjaThe rules of classification societies require the use of redundancy in the systems essential for the safety of the ship. Duplication of pumps in the main engine auxiliary systems like cooling water system, lubricating oil system, fuel oil system is a good example here. Therefore, in the author's opinion, some attention should be paid to this issue. Two important questions arise here. Does duplication of pumps in marine systems...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Investigation on domestic fruits seed oils in personal care emulsion systems
PublikacjaThe use of fruit seed oils in personal care products is of significance to both their function and image. Poland is an important processor of fruit products within the EU, and thus has a large availability of seeds from domestic fruits, which are normally considered to be a waste material. Unfortunately, current literature is scarce of the suitability of these oils for topical use in the form of cosmetic emulsions. Published data...
-
Application of vertical flow constructed wetlands for highly contaminated wastewater treatment: preliminary results
PublikacjaBasing on quantitative and qualitative characteristics of reject waters (RWC) generated during dewatering of digested sewage sludge on centrifuges in conventional WWTP and municipal landfill leachate (LL), the pilot constructed wetlands for treatment of both types wastewater were designed and built. In the paper the conception, design and assumed treatment efficiencies of the pilot plants are presented. The water balance of the...
-
Detection of petroleum products using optical coherence tomography
PublikacjaIn this work, we present a novel method developed for the analysis of the properties of thin layers for detecting petroleum products on a water surface using a commercially available optical coherence tomography (OCT) system. The spectral density analysis of the signal from a spectroscopic OCT (S-OCT) enables us to perform the precision calculation of the thin layer thickness and other properties like homogeneity, and dispersion,...
-
Three-dimensional geographically weighted inverse regression (3GWR) model for satellite derived bathymetry using Sentinel-2 observations
PublikacjaCurrent trends of development of satellite derived bathymetry (SDB) models rely on applying calibration techniques including analytical approaches, neuro-fuzzy systems, regression optimization and others. In most of the cases, the SDB models are calibrated and verified for test sites, that provide favourable conditions for the remote derivation of bathymetry such as high water clarity, homogenous bottom type, low amount of sediment...
-
Water-Lubricated Journal Bearings Marine Applications, Design, and Operational Problems and Solutions
PublikacjaWater-Lubricated Journal Bearings: Marine Applications, Design, and Operational Problems and Solutions provides cutting-edge design solutions, common problems and methods for avoiding them, and material selection considerations for the use of water-lubricated journal bearings in marine environments. These bearings have many advantages, including the absence of the potential for oil contamination. They are also sensitive, and their...
-
Cargo ships heat demand - operational experiment
PublikacjaThe paper presents the results of an experiment conducted on two cargo ships – a 5300 TEU container with a steam heating system and a 7500 dwt general cargo ship with a thermal oil system. On both ships research has been carried out using specially designed measuring equipment. After gathering data about flow velocity and temperatures (steam/ cooling water/ thermal oil/ seawater/ outside air), calculations have been done, resulting...
-
Geotechnical characterization of soft soil deposits in Northern Poland
PublikacjaThis paper presents a geotechnical characterization of deltaic soft soil deposits in the Vistula Marshlands, northern Poland. It shows the limited applicability of organic soil classifications based on Cone Penetration Tests (CPTU) and Dilatometer Tests (DMT). None of the in-situ-based classifications correctly identifies peat. Analysis of the behaviour of contractive/dilative soil layers according to Robertson's updated classification...
-
MAPPING SOUTH BALTIC NEAR-SHORE BATHYMETRY USING SENTINEL-2 OBSERVATIONS
PublikacjaOne of the most promising new applications of remote observation satellite systems (RO) is the near-shore bathymetry estimation based on spaceborn multispectral imageries. In recent years, many experiments aiming to estimate bathymetry in optically shallow water with the use of remote optical observations have been presented. In this paper, optimal models of satellite derived bathymetry (SDB) for relatively turbid waters of the...
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublikacjaThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Emulsification alters simulated gastrointestinal proteolysis of β-casein and β-lactoglobulin
PublikacjaWe have studied the effect of the adsorption of milk proteins at the oil-water interface on their digestibility in simulated gastrointestinal environment. The investigations aimed to characterize how both the breakdown of the adsorbed proteins and the interactions with physiological surfactants, phosphatidylcholine (PC) and bile salts (BS), influence structural transformations of model, protein-stabilized food emulsions in the...
-
Monitoring Trends of Land Use and Land Cover Changes in Rajang River Basin
PublikacjaIn this study, the spatiotemporal changes in land use and land cover (LULC) were evaluated from 1992 to 2015 for the Rajang River Basin (RRB) located in the Sarawak State of Malaysia. The changes in water bodies cropped lands, and forests were assessed based on the available remotely sensed satellite data. Supervised classification with the Maximum-Likelihood-Algorithm technique was adopted for monitoring the LULC changes using...
-
Effect of temperature and ionic strength on volumetric and acoustic properties of solutions of urea alkil derivatives in aqueous NaCl
PublikacjaThe present work was undertaken to study volumetric and acoustic properties for diluted solutions of tetramethylurea in pure water and for urea, n-propylurea, n-butylurea and tetramethylurea in 0.5 or 1 moldm3 aqueous solutions of sodium chloride. This paper presents measured values of densities and sound velocities at T = (288.15, 298.15 and 308.15) K. From these data the apparent molar volumes, , adiabatic compressibilities,...
-
Load effect impact on the exploitation of concrete machine foundations used in the gas and oil industry
PublikacjaMachine foundations is a critical topic in the gas and oil industry, which design and exploitation require extensive technical knowledge. Machine foundations are the constructions which are intended for mounting on it a specific type of machine. The foundation has to transfer dynamic and static load from machine to the ground. The primary difference between machine foundations and building foundations is that the machine foundations...
-
Geographic information system for remote integration of diverse under-water acoustic sensor data
PublikacjaMaritime and port areas throughout the world are exposed to many different hazards, like pollution, terrorism and natural disasters. Early detection, identification and preparation of appropriateesponse strategies is especially important in the case of semi-enclosed basins like the Baltic Sea, mainly due to the marine ecosystems' continuous absorption of pollutants including oil, heavy metals and chemicals. Many of those agents...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublikacjaWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
Mechanical and physical assessment of epoxy, mineral, solvent-based, and water-soluble coating materials
PublikacjaThis paper assesses the behavior of mineral, epoxy (EP), solvent, and water-soluble coatings when exposed to salt and regular water for 28 days. Also, it evaluates the pull-off adhesion strength of the same coating materials applied to concrete slabs saturated with oil and water and dried with two different processes: air-dried for 28 days and air-dried for 14 days plus 14 days in the oven at 70 °C. Properties such as carbonation,...
-
Efficiency of Biomass Energy used for Heating Purposes in a Residential Building in Comparison with other Energy Sources
PublikacjaThis paper discusses the results of analyses investigating the energy efficiency of biomass in comparison with other popular energy carriers used for heating, ventilation and water heating in residential buildings. The compared energy sources were lignite, natural gas, heating oil and electricity produced by conventional and integrated power generation plants. The most efficient variant relying on biomass and the least efficient...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublikacjaIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...
-
Environmental Risk Assessment of WWII Shipwreck pollution
PublikacjaThe pollution of the sea is a global problem that has arisen as a consequence of the industrialization of the world and the intense transportation of crude oil and the products of its refinement. As sailing vessels were replaced by motor propelled ships towards the end of the 19th century, a new source of sea water pollution came into being. Every emergency involving a tanker carrying crude oil and its products is a potential source...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Propagation of Acoustic Disturbances in Shallow Sea
PublikacjaPropagation of acoustic waves in shallow sea differs fundamentally from the same phenomenon occurring in deep sea in view of non-negligible distance from the sea bottom in the first case, where presence of two regions limiting the water layer results in the acoustic pressure distribution induced by a harmonic source has an interferential nature as a result of multi-path propagation of the acoustic signal. These interferential properties...
-
Metody oczyszczania odcieków z procesów przeróbki osadów w komorach fermentacji
PublikacjaOdcieki z beztlenowych procesów przeróbki osadu w komorach fermentacji (tzw. wody poosadowe) są istotnym źródłem azotu dopływającego do części biologicznej oczyszczalni ścieków. Odpowiednie oczyszczanie tych wód może więc, w bardzo istotny sposób wpłynąć na warunki eksploatacji oczyszczalni. Konwencjonalny proces usuwania amoniaku za pomocą dwóch faz, tj. nitryfikacji i denitryfikacji, są coraz częściej zastępowane przez jednoetapowy...
-
The Application of a Mobile Unmanned Device for Monitoring Water and Sediment Pollution in the Port of Gdynia
PublikacjaPollution in the Port of Gdynia can encompass various types of substances and contaminants that affect the quality of water and sediment in this region. Ships entering and leaving the port can release pollutants such as oil, fuel, waste, and chemicals into the water. Controlling and monitoring these pollutants is a crucial part of environmental stewardship. In recent years, uncrewed units have been increasingly in use for in situ...
-
Rational Use of Primary Energy in Single-Family Residential Houses
PublikacjaThis work presents results of the primary energy use for heating residential single-family house. Analysis includes domestic hot water system (DHW) and heating, ventilation and air condition system (HVAC). During researches the conventional and alternative energy sources (natural gas, biomass, fuel oil, bituminous coal, lignite or electric energy obtained from electric power system – EPS) were used in DHW and HVAC systems. Furthermore...
-
Risks caused by microbiologically influenced corrosion in diesel fuel storage tanks
PublikacjaMicrobiologically influenced corrosion (MIC) poses serious problems for the petrochemical and refinery industries. Particularly favourable conditions for MIC arise in storage tanks and transmission pipelines for mixtures of diesel oil with the addition of a biocomponent (in Poland 7%). The best conditions for the development of MIC occur at the fuel-water interface, where microorganisms are provided with a source of food and water,...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublikacjaIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
Corrosion hazards and inhibitor protection in the seawater injection system on the Baltic sea rig
PublikacjaOil extraction efficiency in LOTOS Petrobaltic Company is increased by means of injection of seawater into an oilfield aquifer, which is implemented on the Baltic Beta rig, operating on the Baltic Sea. Operational experience has shown a significant degree of corrosion aggressiveness in the injected water, which necessitates frequent repairs of the seawater injection installation. Evaluation of the corrosion phenomena is crucial...
-
Student Perspectives on the 2017 ESA Concurrent Engineering Challenge
PublikacjaIn September 2017, the first ESA Academy’s Concurrent Engineering Challenge (CEC) was held, giving 88 Master’s and PhD-level students from twelve ESA Member and Associate States a powerful platform to experience system engineering in an intense, fast paced, and real-world environment. Within four days, teams of physics and engineering students in Concurrent Design Facilities (CDF) located in Politecnico di Torino, Universidad Polit´ecnica...
-
Study on the Coastline Evolution in Sopot (2008–2018) Based on Landsat Satellite Imagery
PublikacjaThe coastline is the boundary between the water surface in a reservoir or watercourse and the land, which is characterised by high instability and functional diversity. For these reasons, research on coastal monitoring has been conducted for several decades. Currently, satellite images performed with synthetic aperture radars (SARs) are used to determine its course and variability together with high-resolution multispectral imagery...
-
Comparative study of selected fluids for use in supercritical Organic Ranking Cycles
PublikacjaIn view of increasing interest in improving energy efficiency of energy conversion devices, there is an increasing requirement of combined production of heat and electricity as well as demand for increased implementation of renewable energy resources. The micro cogenerative units utilizing the Organic Rankine Cycle are focusing the attention of many research centres around the world. In the present paper calculations of ORC cycles...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Reducing Air Pollutant Emissions from the Residential Sector by Switching to Alternative Energy Sources in Single-Family Homes
PublikacjaThe paper discusses a scenario for adapting residential buildings to the requirements of the EU climate and energy package. It analyzes the option of reducing pollutant emissions to ambient air by switching to alternative energy sources in a typical single-family residential building. The most common sources of energy in central heating and ventilation systems and water heating systems were compared, and the analyzed energy carriers...
-
Preparation and characterization of monometallic (Au) and bimetallic (Ag/Au) modified-titania photocatalysts activated by visible light
PublikacjaThe Au-TiO2 and Ag/Au-TiO2 nanoparticles have been prepared using a water-in-oil microemulsion system of water/AOT/cyclohexane and water/Triton X-100/cyclohexane. The obtained photocatalysts were subsequently characterized by a BET method, DRS spectroscopy, X-ray photoelectron emission spectroscopy (XPS), scanning transmission electron microscopy (STEM) and X-ray powder diffraction analysis (XRD). For gold-doped titanium (IV) oxide...
-
Metoda f-chart w zastosowaniu do projektu instalacji solarnej w budownictwie jednorodzinnym
PublikacjaW artykule przedstawiono algorytm obliczeń cieplnych związanych z konwersją promieniowania cieplnego oraz analizę efektów pracy instalacji solarnej przy użyciu metody korelacyjnej f-chart. Zaprezentowany algorytm obliczeń cieplnych oraz omówiona w artykule podstawowa odmiana metody f-chart zostały poparte przykładem obliczeniowym dla instalacji solarnej, która wykorzystywana jest do wspomagania układu przygotowania c.w. dla potrzeb...
-
The effect of paleo-environment on hydrocarbon generation potential: Example from Vaca Muerta Formation, Neuquén Basin, Argentina
PublikacjaA 137-m continuous core from the Jurassic-Early Cretaceous marine derived oil shale with the maturity Ro about 0.7 %, representing the oil window in the Vaca Muerta Formation, Neuquén Basin, Argentina, was examined using geological, mineralogical, petrographic, and geochemistry techniques. Three distinct intervals were identified within the core: the upper carbonate-rich section with intense bioturbation, indicating dysoxic to...
-
KONCEPCJA DWU-ŚMIGŁOWEJ ELEKTROWNI WIATROWEJ I ELEKTROWNI SZCZYTOWO-POMPOWEJ NA WZGÓRZU SZUBIENICZNYM
PublikacjaDogodne warunki terenowe Wzgórza Szubienicznego w Gdańsku oraz istniejąca tam infrastruktura stanowią podstawę do rozważenia koncepcji doposażenia instalacji badawczej Laboratorium Innowacyjnych Technologii Elektroenergetycznych i Integracji Odnawialnych Źródeł Energii LINTE^2 w skojarzony, hydro-wiatrowy zespół wytwórczy. W artykule zaproponowano koncepcję budowy elektrowni pompowo-szczytowej z turbinami Francisa oraz elektrowni...
-
Preparation and Characterization of Au/Pd Modified-TiO2 Photocatalysts for Phenol and Toluene Degradation under Visible Light—The Effect of Calcination Temperature
PublikacjaRutile loaded with Au/Pd nanoparticles was prepared using a water-in-oil microemulsion system of water/AOT/cyclohexane followed by calcination.Theeffect of calcination temperature (from350 to 700∘C) on the structure ofAu/Pd nanoparticles deposited at rutile matrix and the photocatalytic properties of Au/Pd-TiO2 was investigated in two model reactions (toluene degradation in gas phase and phenol degradation in aqueous phase). The...
-
Complex Corrosion Monitoring System for Crude Distillation Unit in Form of Neutral Network
PublikacjaComplex and successful corrosion monitoring of refinery processes can significantly reduce material losses and failure risk. The developed corrosion monitoring system is based on online ultrasonic sensors, ER (electrical resistance) probes, gravimetric method and multipoint analytical analysis of chemical composition of the fluids. Additional online LPR (linear polarization resistance) sensors controlling corrosiveness of sour...
-
Viability of fruit seed oil O/W emulsions in personal care products
PublikacjaThe use of fruit seed oils in personal care products is of significance to both their function and image. Poland is an important processor of fruit products within the EU, and thus has a large availability of seeds from domestic fruits, which are normally considered to be a waste material or feed for livestock. Unfortunately, current literature is scarce of the suitability of these oils for topical dermatological use in the form...
-
The concept of research on ecological, energy and reliability effects of modified marine fuel oils application to supply compression-ignition engines in real conditions
PublikacjaWithin the article, basic assumptions of the research project financed by Regional Fund for Environmental Protection and Water in Gdansk were described. The project concerns the experimental investigations carried out on laboratory compression-ignition engine in conditions of its supply with a non-standard marine fuel oil. Configuration and measuring capability of laboratory test bed presently being constructed were introduced....
-
Hydro Lubricants: Water-based lubricants for hydropower applications
PublikacjaSeveral different base oil types exist in the market including mineral and synthetic oils (e.g. polyalphaolefins, ester, polyglycol, etc.) and are currently widely in use. Although synthetic oils have drawn great attention over the past few decades in terms of their tribological benefits, mineral oils are still widely used in hydropower applications due primarily to their low cost and easy miscibility with other oils. However,...
-
CZYNNIKI DECYDUJĄCE O PRZYDATNOŚCI KOMPUTEROWEGO MODELU PRZEPŁYWÓW W SIECI WODOCIĄGOWEJ
PublikacjaW pracy poddano analizie wielozadaniowy proces tworzenia komputerowego modelu przepływów. W efekcie zidentyfikowano szereg czynników ograniczających obszar stosowania modelu w praktyce inżynierskiej. W zakresie pozyskiwania danych strukturalnych i operacyjnych wskazano potencjalne źródła błędów, które przyczyniają się do zmniejszenia dokładności odwzorowania stanu rzeczywistego. Specjalną rangę nadano specyfikacji czynników związanych...
-
Improving performance of large thrust bearings through modeling and experimentation
PublikacjaLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
Effect of Simultaneous Valve Closures in Hydraulic Piping Systems
PublikacjaThe paper investigates wave interference (between pressure waves) occurring in simple hydraulic systems. Water hammer was induced by simultaneous closure of three valves located at the reservoirs of a “Y” type hydraulic system. Numerical simulations were carried out with the help of the freeware computer package Allievi enabling the reader to replicate results in a direct manner. The influence of the following quantities has been...
-
Protection and viability of fruit seeds oils by nanostructured lipid carrier (NLC) nanosuspensions
PublikacjaIn this paper, we focused on the development of nanostructured lipid carriers (NLCs) for dermal application. The NLC matrix was designed as a protective reservoir of biological active compounds that naturally occur in domestic fruit seed oils. Over the years, emulsions, as a popular physicochemical form of personal care products, were refined in order to obtain the best possible penetration into the skin of any bioactive compound...
-
Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant
PublikacjaIn the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR) working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller...
-
Atmospheric opacity estimation based on IWV derived from GNSS observations for VLBI applications
PublikacjaThermal emission of atmospheric water vapor has a great influence on the calibration of radio astronomical observations at millimeter wavelengths. The phenomenon of an atmospheric water vapor emits noise signal and attenuates astronomical emission. At 22 GHz, integrated water vapor (IWV) obtained from global navigation satellite systems (GNSS) is strictly related to atmospheric opacity (τ0), which is a crucial parameter for data...
-
Design and Application of Magnetic Photocatalysts for Water Treatment. The Effect of Particle Charge on Surface
PublikacjaCore-interlayer-shell Fe3O4/SiO2/TiO2, CoFe2O4/SiO2/TiO2 and BaFe12O19/SiO2/TiO2 magnetic photocatalysts were obtained. A water-in-oil microemulsion system with suitable surfactants was used for functionalization of the magnetic core with silica interlayer and TiO2-based photocatalyst. Uncoated and coated particles were characterized by electrophoretic meaurements, X-ray diffractometry (XRD), scanning electron microscopy (SEM),...
-
Two-step Conversion of Crude Glycerol Generated by Biodiesel Production into Biopolyols: Synthesis, Structural and Physical Chemical Characterization
PublikacjaIn this work biopolyols were synthesized via two-step process from crude glycerol and castor oil. For better evaluation of analyzed process, the impact of its time and temperature on the structure and properties of biopolyols was determined. Obtained results fully justified conducting of synthesis in two steps. Prepared materials were characterized by hydroxyl value and water content comparable to polyols industrially applied in...
-
RAPESEED PELLET - A BYPRODUCT OF BIODIESEL PRODUCTION - AS AN EXCELLENT RENEWABLE ENERGY SOURCE
PublikacjaVegetable oils are renewable feedstock currently being used for production of biofuels from sustainable biomass resources. The existing technology for producing diesel fuel from plant oils, such as rapeseed, soybean, canola and palm oil are largely centered on transesterification of oils with methanol to produce fatty acid methyl esters (FAME) or biodiesel. Rapeseed pellet - crushed seed residue from oil extraction is a byproduct...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublikacjaHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Chemical Characteristics and Thermal Oxidative Stability of Novel Cold-Pressed Oil Blends: GC, LF NMR, and DSC Studies
PublikacjaPlant oils contain a high content of unsaturated fatty acids. Studies of food products have revealed a considerable disproportion in the ratio of ω6 to ω3. This article presents information on the healthful qualities of eight new oil blends that contain a beneficial proportion of ω6 to ω3 fatty acids (5:1), as well as their degradation during heating at 170 and 200 °C. The fatty acid profile was analyzed by gas chromatography (GC),...
-
Improved Empirical Coefficients for Estimating Water Vapor Weighted Mean Temperature over Europe for GNSS Applications
PublikacjaDevelopment of the so-called global navigation satellite system (GNSS) meteorology is based on the possibility of determining a precipitable water vapor (PWV) from a GNSS zenith wet delay (ZWD). Conversion of ZWD to the PWV requires application of water vapor weighted mean temperature (Tm) measurements, which can be done using a surface temperature (Ts) and its linear dependency to the Tm. In this study we analyzed up to 24 years...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublikacjaCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Nonlinearity shaping in nanostructured glass-diamond hybrid materials for optical fiber preforms
PublikacjaNanodiamond integration with optical fibers has proved a compelling methodology for magneto-optics. We reveal that the applicability of nanodiamonds in nonlinear optics goes beyond the previous demonstrations of frequency converters. Instead, we exploit the recently reported volumetric integration of nanodiamonds along the optical fiber core and show that the nonlinear response of glasses can be manipulated by nanodiamonds. By...
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublikacjaFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
On the relationship between the structural and volumetric properties of solvated metal ions in O-donor solvents using new structural data in amide solvents
PublikacjaThe structures of the N,N-dimethylformamide (dmf), N,N-dimethylacetamide (dma), and N,N-dimethylpropionamide (dmp) solvated strontium and barium ions have been determined in solution using large angle X-ray scattering and EXAFS spectroscopy. The strontium ion has a mean coordination number (CN) between 6.2 and 6.8, and the barium ion has a mean CN between 7.1 and 7.8 in these amide solvents. The non-integer numbers indicates that...
-
Laboratory research on the influence of swelling clay on the quality of borehole cementing and evaluation of clay-cutting wellbore tool prototype
PublikacjaSwelling clay phenomenon is frequently observed during oil and gas drilling operations and has a significant impact on the quality of cementing procedure. Certain types of clayey minerals increase their volume in contact with water-based drilling fluids. After drilling is completed, borehole remains unsupported and filled with waterbased drilling fluids for several hours, before a casing string is inserted and secured with cement....
-
Characterizing surface and air temperature in the Baltic Sea coastal area using remote sensing techniques and GIS
PublikacjaEstimation of surface temperature using multispectral imagery retrieved from satellite sensors constitutes several problems in terms of accuracy, accessibility, quality and evaluation. In order to obtain accurate results, currently utilized methods rely on removing atmospheric fluctuations in separate spectral windows, applying atmospheric corrections or utilizing additional information related to atmosphere or surface characteristics...
-
Sea surface temperature distribution during upwelling along the Polish Baltic coast
PublikacjaAmong over 150 maps of sea surface temperature in the Polish Baltic coastal region derived from satellite data during the warm period of the year (April-October) in 2000-2002, 41 cases were noted where its distribution showed characteristic features indicating the occurrence of coastal upwelling. The fundamental parameters of range, probability of occurrence and temperature modification caused by water from deeper sea layers...
-
A review on recent advances in the application of biosurfactants in wastewater treatment
PublikacjaMicroorganisms produce a variety of non-conventional surface-active molecules, known as biosurfactants. The biosurfactants find diverse applications in the oil industry, agriculture, emulsifiers, and wastewater treatment, to name a few. Since they are produced from microbes, advantages such as biodegradability, lower toxicity, and environmental compatibility can be leveraged compared to the chemical surfactants. Recently, biosurfactants...
-
Chlorinated solvents in a petrochemical wastewater treatment plant: Anassessment of their removal using self-organising maps
PublikacjaThe self-organising map approach was used to assess the efficiency of chlorinated solvent removal frompetrochemical wastewater in a refinery wastewater treatment plant. Chlorinated solvents and inorganicanions (11 variables) were determined in 72 wastewater samples, collected from three different purificationstreams. The classification of variables identified technical solvents, brine from oil desalting andrunoff sulphates as pollution...
-
On the Structure and Volumetric Properties of Solvated Lanthanoid(III) Ions in Amide Solutions
PublikacjaThe coordination chemistry and the volumetric properties of three representative lanthanoid(III) ions lanthanum-(III), gadolinium(III), and lutetium(III) have been studied in three amide solvents with gradually increasing spatial demand upon coordination: N,N-dimethylformamide (dmf)
-
Evaluation of respiration capacity of VF in hybrid constructed wetland systems.
PublikacjaThree VF-beds operating in hybrid constructed wetlands in configuration HF-VF-HF were analysed. These hybrid constructed wetlands provide the II stage biological treatment. They are located in Pommerania voivodship, in Sarbsk, Wiklino and Wieszyno, and their capacities are 29.5, 14.2 and 21.6 m3/d, respectively. The article focuses on performance and operation of VF-CW plants during one year. Based on removal of organic matter...