wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: IDENTIFICATION OF NONSTATIONARY PROCESSES, SELECTION OF MODEL ORDER, SELECTION OF ESTIMATION MEMORY
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
Statistically efficient smoothing algorithm for time-varying frequency estimation
PublikacjaThe problem of extraction/elimination of a nonstationary sinusoidal signal from noisy measurements is considered. This problem is usually solved using adaptive notch filtering (ANF) algorithms. It is shown that the accuracy of frequency estimates can be significantly increased if the results obtained from ANF are backward-time filtered by an appropriately designed lowpass filter. The resulting adaptive notch smoothing (ANS) algorithm...
-
Frequency based criterion for distinguishing tonal and noisy spectral components
PublikacjaA frequency-based criterion for distinguishing tonal and noisy spectral components is proposed. For considered spectral local maximum two instantaneous frequency estimates are determined and the difference between them is used in order to verify whether component is noisy or tonal. Since one of the estimators was invented specially for this application its properties are deeply examined. The proposed criterion is applied to the...
-
The control software of the portable raman spectrometer
PublikacjaThe paper contains a description of the control software of a portable Raman spectrometer which was built in the Department of Optoelectronics and Electronic Systems Faculty of Electronics, Telecommunications and Informatics Gdansk University of Technology. The software has modular structure, which includes the laser control module and the spectrum acquisition module (laser power selection, working mode and data acquisition time)...
-
Methodology of Selecting the Optimal Receptor to Create an Electrochemical Immunosensor for Equine Arteritis Virus Protein Detection
PublikacjaThe study reports a methodology of selecting the optimal receptor to create an electrochemical immunosensor for equine arteritis virus (EAV) protein detection. The detection was based on antigen recognition by antibodies immobilized on gold electrodes. Modification steps were controlled by electrochemical impedance spectroscopy and cyclic voltammetry measurements. In order to obtain the impedance immunosensor with the best parameters,...
-
Effect of excitation intensity on slope stability assessed by a simplified approach
PublikacjaThe paper concerns the selection of a design accelerograms used for the slope stability assessment under earthquake excitation. The aim is to experimentally verify the Arias Intensity as an indicator of the excitation threat to the slope stability. A simple dynamic system consisting of a rigid block on a rigid inclined plane subjected to horizontal excitation is adopted as a slope model. Strong ground motions recorded during earthquakes...
-
Estymacja parametrów kanału NB-IoT w łączu w dół.
PublikacjaArtykuł dotyczy doboru metody estymacji parametrów kanału, odpowiedniej do zastosowania w terminalu wąskopasmowego Internetu Rzeczy. Przedstawiono strukturę sygnału pilotowego NRS, używanego do wyznaczenia współczynników kanału w LTE-NB. Zaproponowano cztery warianty metody wyznaczenia współczynników kanału dla całej ramki transmisyjnej. Dokonano oceny tych wariantów w oparciu o dwa wskaźniki jakościowe skojarzone z błędem odtworzonych...
-
Multi-state multi-reference Møller-Plesset second-order perturbation theory for molecular calculations
PublikacjaThis work presents multi‐state multi‐reference Møller–Plesset second‐order perturbation theory as a variant of multi‐reference perturbation theory to treat electron correlation in molecules. An effective Hamiltonian is constructed from the first‐order wave operator to treat several strongly interacting electronic states simultaneously. The wave operator is obtained by solving the generalized Bloch equation within the first‐order...
-
Thermal and technological aspects of double face grinding of C45 carbon steel
PublikacjaIn grinding, the contact zone temperature is a decisive factor influencing the achievable surface quality and the grinding tool wear. In contrast to other grinding processes, only few information regarding double face grinding with planetary kinematics when processing steel is known up to date. Since the successive substitution of in-dustrial double-sided lapping processes by double-sided grinding, it has become necessary to the...
-
Zastosowanie Systemu Informacji Geograficznej (GIS) w identyfikacji potencjalnych klastrów
PublikacjaPolityka klastrowania znajduje się w strategicznych dokumentach rozwoju gospodarczego Polski i nastawiona jest na promowanie współpracy regionalnej ponadregionalnej. Budowa klastra na szczeblu regionalnym wymaga jednak w pierwszym etapie jego identyfikacji a w kolejnym selekcji potencjalnych uczestników. Dotychczas stosowane jakościowe i ilościowe metody identyfikacji klastrów, nie są do takich zadań przystosowane lub ich stopień...
-
Optimization model of agile team’s cohesion
PublikacjaTeam’s cohesion is one of the most important factors of IT project execution effectiveness. Optimization of team’s cohesion gives the possibility of reducing the risk of project failure. It also allows to increase the teamwork efficiency and thus optimize time of tasks execution, increase the guarantee of maintaining the scope of the project and the chance of achieving a given level of products quality. This article presents determination...
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublikacjaIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Inclusive Communication Model Supporting the Employment Cycle of Individuals with Autism Spectrum Disorders
PublikacjaDifficulties with interpersonal communication experienced by individuals with autism spectrum disorders (ASD) significantly contribute to their underrepresentation in the workforce as well as problems experienced while in employment. Consistently, it is vital to understand how communication within the employment cycle of this group can be improved. This study aims to identify and analyze the possibilities of modifying the communication...
-
Comparative Evaluation of Selected Biological Methods for the Removal of Hydrophilic and Hydrophobic Odorous VOCs from Air
PublikacjaDue to increasingly stringent legal regulations as well as increasing social awareness, the removal of odorous volatile organic compounds (VOCs) from air is gaining importance. This paper presents the strategy to compare selected biological methods intended for the removal of different air pollutants, especially of odorous character. Biofiltration, biotrickling filtration and bioscrubbing technologies are evaluated in terms of...
-
Methodology of Selecting the Optimal Receptor to Create an Electrochemical Immunosensor for Equine Arteritis Virus Protein Detection
PublikacjaThe study reports a methodology of selecting the optimal receptor to create an electrochemical immunosensor for equine arteritis virus (EAV) protein detection. The detection was based on antigen recognition by antibodies immobilized on gold electrodes. Modification steps were controlled by electrochemical impedance spectroscopy and cyclic voltammetry measurements. In order to obtain the impedance immunosensor with the best parameters,...
-
Application of multicriteria decision analysis to assess the greenness of molecularly imprinted polymers synthesis components
PublikacjaThe study applies multicriteria decision analysis (MCDA) to rank the components of molecularly imprinted polymers (MIPs) synthesis according to their greenness. The components are taken from papers that are describing synthesis of MIPs for persistent organic pollutants (POPs) sorbents. Functional monomers (n = 14), target/surrogate molecules (n = 10), porogens (n = 8), cross-linking agents (n = 8) and initiators (n = 4) are described...
-
Numerical simulations of novel GFRP sandwich footbridge
PublikacjaIn the following paper some aspects of numerical analysis and designing stages of a footbridge made of composite materials are elucidated. Because of the used materials the design process in this case is not ordinary and requires the development of concepts, material selections, identification of material properties, numerical simulations, strength calculations, serviceability and durability analyses. This contribution presents...
-
Symmetrical power line conditioner - basic properties
PublikacjaIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model, were talked over. In short form power balance as well as fundamental dependences and analytical model with regard of decoupling circuits, were investigated. Applied method for DC link capacitance...
-
Modeling and experimental investigation of the small UPQC systems
PublikacjaIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model were talked over. In short form power balance as well as fundamental dependences and analytic model with regard of decoupling circuits were investigated. Applied method for DC link capacity selection...
-
The impact of the temperament model on the behavior of an autonomous driver
PublikacjaBecause it is generally believed that the personality and temperament of a human driver influence his/her behavior on the road, the article presents a computational model of the temperament of an autonomous agent - a driver. First, a short review of the four ideas of Galen’s temperament in psychology is presented. Temperament traits are grouped into four other sets, one of which is chosen for implementation in the project of integration...
-
Machine learning-based prediction of residual drift and seismic risk assessment of steel moment-resisting frames considering soil-structure interaction
PublikacjaNowadays, due to improvements in seismic codes and computational devices, retrofitting buildings is an important topic, in which, permanent deformation of buildings, known as Residual Interstory Drift Ratio (RIDR), plays a crucial role. To provide an accurate yet reliable prediction model, 32 improved Machine Learning (ML) algorithms were considered using the Python software to investigate the best method for estimating Maximum...
-
Approval of an Arrangement in the Restructuring Proceedings and the Financial Condition of Companies Listed on the Stock Exchanges in Warsaw. Is There Any Relationship?
PublikacjaThis paper attempts to identify the financial indicators differentiating companies that are insolvent or at risk of insolvency and have successfully entered into an arrangement with their creditors from those that have not. In addition, a two-factor model for predicting the odds of an arrangement has been proposed. The research was conducted using a population of companies listed on stock exchanges in Warsaw that initiated restructuring...
-
High quality speech codec employing sines+noise+transients model
PublikacjaA method of high quality wideband speech signal representation employing sines+transients+noise model is presented. The need for a wideband speech coding approach as well as various methods for analysis and synthesis of sines, residual and transient states of speech signal is discussed. The perceptual criterion is applied in the proposed approach during encoding of sines amplitudes in order to reduce bandwidth requirements and...
-
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
PublikacjaTravel time is a measure commonly used for traffic flow modelling and traffic control. It also helps to evaluate the quality of traffic control systems in urban areas. Traffic control systems that use traffic models to predict changes and disruptions in vehicle flows have to use vehicle speed-prediction models. Travel time estimation studies the effects of traffic volumes on a street section at an average speed. The TRISTAR Integrated...
-
Marek Zienkiewicz dr inż.
OsobyDoktor inżynier Marek Hubert dwojga imion Zienkiewicz jest absolwentem Wydziału Geodezji, Inżynierii Przestrzennej i Budownictwa Uniwersytetu Warmińsko-Mazurskiego w Olsztynie. Zainteresowania naukowe w okresie studiów inżynierskich, magisterskich i doktoranckich rozwijał pod opieką przedstawicieli olsztyńskiej szkoły geodezyjnego rachunku wyrównawczego. W roku 2011 uzyskał tytuł zawodowy magistra inżyniera w zakresie geodezji...
-
From the multiple frequency tracker to the multiple frequency smoother
PublikacjaThe problem of extraction/elimination of nonstationary sinusoidalsignals from noisy measurements is considered. This problem is usually solved using adaptive notch filtering (ANF)algorithms. It is shown that the accuracy of frequency estimates can be significantly increased if the results obtained from ANF are backward-time filtered by an appropriately designed lowpass filter. The resulting adaptive notch smoothing (ANS)algorithm...
-
Balancing agility and discipline in a research project
PublikacjaSuccessful software development requires both agility and discipline. Optimal selection of methods, however, is not an easy task. The problem becomes even more difficult for long lasting projects. Appropriate selection of methods involving skillful introduction and abandonment of certain practices in time makes the whole process dynamic. The paper presents in this context a research project which was realized in a few iterations....
-
Sieć sensorowa do rejestracji drgań górnej sieci trakcyjnej w celach diagnostyki eksploatacyjnej
PublikacjaWraz ze wzrostem prędkości kolejowych pojazdów elektrycznych zwiększają się wymagania utrzymania sieci trakcyjnej w odpowiednim stanie technicznym. Ciągły monitoring i diagnostyka pozwalają wykrywać pogarszającą się jakość odbioru prądu z sieci jezdnej. Jedną z metod jest umieszczenie czujników przyspieszenia na przewodzie jezdnym. Analiza przebiegu przyspieszenia pozwala określić jakość współpracy sieci jezdnej z pantografem....
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublikacjaThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
A robust sliding mode observer for non-linear uncertain biochemical systems
PublikacjaA problem of state estimation for a certain class of non-linear uncertain systems has been addressed in this paper. In particular, a sliding mode observer has been derived to produce robust and stable estimates of the state variables. The stability and robustness of the proposed sliding mode observer have been investigated under parametric and unstructured uncertainty in the system dynamics. In order to ensure an unambiguous non-linear...
-
Systematic Literature Review for Emotion Recognition from EEG Signals
PublikacjaResearchers have recently become increasingly interested in recognizing emotions from electroencephalogram (EEG) signals and many studies utilizing different approaches have been conducted in this field. For the purposes of this work, we performed a systematic literature review including over 40 articles in order to identify the best set of methods for the emotion recognition problem. Our work collects information about the most...
-
Systematic Literature Review for Emotion Recognition from EEG Signals
PublikacjaResearchers have recently become increasingly interested in recognizing emotions from electroencephalogram (EEG) signals and many studies utilizing different approaches have been conducted in this field. For the purposes of this work, we performed a systematic literature review including over 40 articles in order to identify the best set of methods for the emotion recognition problem. Our work collects information about the most...
-
Risk Modelling with Bayesian Networks - Case Study: Construction of Tunnel under the Dead Vistula River in Gdansk
PublikacjaThe process of decision-making in public procurement of construction projects during the preparation and implementation phases ought to be supported by risk identification, assessment, and management. In risk assessment one has to take into account factors that lead to risk events (background info), as well as the information about the risk symptoms (monitoring info). Typically once the risks have been assessed a decision-maker...
-
Parallelization of Compute Intensive Applications into Workflows based on Services in BeesyCluster
PublikacjaThe paper presents an approach for modeling, optimization and execution of workflow applications based on services that incorporates both service selection and partitioning of input data for parallel processing by parallel workflow paths. A compute-intensive workflow application for parallel integration is presented. An impact of the input data partitioning on the scalability is presented. The paper shows a comparison of the theoretical...
-
Magnetic superhydrophobic melamine sponges for crude oil removal from water
PublikacjaThis paper proposes the preparation of a new sorbent material based on melamine sponges (MS) with superhydrophobic, superoleophilic, and magnetic properties. This study involved impregnating the surface of commercially available MS with eco-friendly deep eutectic solvents (DES) and Fe3O4 nanoparticles. The DES selection was based on the screening of 105 eutectic mixtures using COSMO-RS modeling. Other parameters affecting the efficiency...
-
Using Wearable Electronics to Estimate Usefulness of Heart Rate Variability for Bathing Person Identif Cation
PublikacjaIn this paper the possibility of person identification based on biosignal is investigated. The work focus on the analysis of the changes in intervals between successive R-waves of electrocardiogram (ECG) recorded by wearable electronics in form of a necklaces. The main idea behind this project is to find efficient tool which may prevent sudden consciousness loss episodes or even sudden death episodes related to rapid temperature...
-
Sphere Drive and Control System for Haptic Interaction With Physical, Virtual, and Augmented Reality
PublikacjaA system for haptic interaction with physical, virtual, and augmented realities, founded on drive and measurement elements (DMEs), is considered. The system consists of eight DME rolls equipped with linear actuators, able to measure their angular velocity, drive the sphere, and adjust downforce (pressing the roll against the sphere). Two modeling issues are addressed. Special effort is put in to compensate for various technical...
-
Probabilistic Methods in Reliability Assessment of Engineering Lightweight Structures
PublikacjaThe paper considers the probability-based analysis of structural safety measures. Two different numerical examples of representative lightweight structures are considered – a submerged truss tower supporting an offshore platform, and an overhead power line support truss tower. On the basis of these examples, the importance of a motivated selection of analysis method and a proper choice of the number of important variables is shown....
-
Application of gas chromatography to the analysis of spirit-based alcoholic beverages
PublikacjaSpirit-based beverages are alcoholic drinks, which production processes are dependent on the type and origin of raw materials. The composition of this complex matrix is difficult to analyze and scientists commonly choose a gas chromatography techniques for this reason. With a wide selection of extraction methods and detectors it is possible to provide qualitative and quantitative analysis for many chemical compounds with a various...
-
Determination of Odor Air Quality Index (OAQII) Using Gas Sensor Matrix
PublikacjaThis article presents a new way to determine odor nuisance based on the proposed odor air quality index (OAQII), using an instrumental method. This indicator relates the most important odor features, such as intensity, hedonic tone and odor concentration. The research was conducted at the compost screening yard of the municipal treatment plant in Central Poland, on which a self-constructed gas sensor array was placed. It consisted...
-
On low-fidelity models for variable-fidelity simulation-driven design optimization of compact wideband antennas
PublikacjaThe paper addresses simulation-driven design optimization of compact antennas involving variable-fidelity electromagnetic (EM) simulation models. Comprehensive investigations are carried out concerning selection of the coarse model discretization density. The effects of the low-fidelity model setup on the reliability and computational complexity of the optimization process are determined using a benchmark set of three ultra-wideband...
-
Hierarchical predictive control of integrated wastewater treatment systems
PublikacjaThe paper proposes an approach to designing the control structure and algorithms for optimising control of integrated wastewater treatment plant-sewer systems (IWWTS) under a full range of disturbance inputs. The optimised control of IWWTS allows for significant cost savings, fulfilling the effluent discharge limits over a long period and maintaining the system in sustainable operation. Due to the specific features of a wastewater...
-
Sebastian Wilczewski dr inż.
OsobyDr inż. Sebastian Wilczewski jest zatrudniony na stanowisku adiunkta w Katedrze Zastosowań Informatyki w Zarządzaniu, Wydział Zarządzania i Ekonomii. Ponadto od ponad 20 lat pracuje w firmach informatycznych, gdzie zajmował stanowiska od inżyniera i konsultanta, poprzez stanowisko Project Managera, Portfolio Manager i Proces Ownera aż do stanowiska Team Leadera dla zespołu około 30 analityków IT. Zdobytą wiedzą i doświadczeniem...
-
Use of Modified Cuckoo Search algorithm in the design process of integrated power systems for modern and energy self-sufficient farms
PublikacjaIn the face of increasingly stringent pollutant emission regulations, designing an agricultural holding becomes a difficult challenge of connecting a large number of coefficients that describe an energy system of a farm in regard to its ecological and economic efficiency. One way to cope with this issue is to design an energy self-sufficient farm that integrates various technologies, including renewable energy. However, the selection...
-
Optimally regularized local basis function approach to identification of time-varying systems
PublikacjaAccurate identification of stochastic systems with fast-varying parameters is a challenging task which cannot be accomplished using model-free estimation methods, such as weighted least squares, which assume only that system coefficients can be regarded as locally constant. The current state of the art solutions are based on the assumption that system parameters can be locally approximated by a linear combination of appropriately...
-
Development Of Dynamic Method For Evaluation Of Corrosion Rate On The Example Of Organic Corrosion İnhibitor
PublikacjaMeasurements of the corrosion rate belong to the most important aspects of materials science. In order to reduce material loss corrosion inhibitors are used. However selection of proper inhibitor should be based on evaluation of its mechanism and effective concentrations. Mechanism of inhibition usually has dynamic character so physicochemical parameters are changing in time. Most of actually used methods...
-
An interval estimator for chlorine monitoring in drinking water distribution systems under uncertain system dynamics, inputs and chlorine concentration measurement errors
PublikacjaThe design of an interval observer for estimation of unmeasured state variables with application to drinking water distribution systems is described. In particular, the design process of such an observer is considered for estimation of the water quality described by the concentration of free chlorine. The interval observer is derived to produce the robust interval bounds on the estimated water quality state variables. The stability...
-
Fuel, Oils and Greases, W, E, sem.01, zimowy 22/23
Kursy OnlineDivision and origin of fuels. Fossil energy resources in Poland and in the world. Production and structure of fuel consumption. Main directions of crude oil processing. Classification and physical properties of gaseous and liquid fuels - natural gas, gasoline, kerosene, diesel oil, heating oil. Classification and characteristic indicators of solid fuels - hard coal, lignite, peat. Fuel contaminants and methods of their removal....
-
Recurrent Neural Network Based Adaptive Variable-Order Fractional PID Controller for Small Modular Reactor Thermal Power Control
PublikacjaThis paper presents the synthesis of an adaptive PID type controller in which the variable-order fractional operators are used. Due to the implementation difficulties of fractional order operators, both with a fixed and variable order, on digital control platforms caused by the requirement of infinite memory resources, the fractional operators that are part of the discussed controller were approximated by recurrent neural networks...
-
Dynamic impedance spectra of programmable dynamically changing RC model based on digital potentiometers
Dane BadawczeThe dataset presents non-stationary impedance spectra of the RC model presented in the figure below. This model contains two digital potentiometers controlled digitally by the microcontroller. This solution allows to programmably control the value of the model impedance. Thanks to this, the model can be used as a test engine for evaluation of the dynamic...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 200 mV
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 0 V
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 600 mV
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 400 mV
Dane BadawczeThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Cognitive Systems, Concepts, Processes, and Techniques for the Age of Industry 4.0
PublikacjaThe aim of this Guest Edition of Cybernetics and Systems is to present a wide-ranging scale of concepts and processes being currently researched, developed, and evaluated in real life settings in anticipation of incoming Industry 4.0 era. With the fourth industrial revolution expectation, the broad spectrum of cognitive approaches have emerged as an attempt to mimic and augment, in some way, human intelligence. Intelligence, in...
-
Selected manufacturing difficulties encountered during setup of machining on cnc multi-axis linear automatic lathe and on cnc multi-spindle turning centers
PublikacjaThe article presents the observed manufacturing technology implementation difficulties in workshop practice, resulting from the construction and principles of operation on the DMG’s SPRINT 32/5 CNC linear automatic lathe and on the Mazak’s HQR 150 MSY and QTN 200 MS CNC turn - mill centers, and discusses possible rules for solving the production problems encountered. The article also discusses the principles of dividing the machining...
-
Simulation model of IPMSM drive with rotor position estimator
PublikacjaThe paper presents a simulation model of electric drive consisting of: IPMSM motor, inverter and digital controller. The model was designed in Mathlab/Simulink. By modelling of the controller its discrete operation was taken into account in order to simulate precisely a specific sensorless control algorithm. A method for estimation of angular rotor position was proposed. Its mathematical algorithm was explained and errors were...
-
Selected Technical Issues of Deep Neural Networks for Image Classification Purposes
PublikacjaIn recent years, deep learning and especially Deep Neural Networks (DNN) have obtained amazing performance on a variety of problems, in particular in classification or pattern recognition. Among many kinds of DNNs, the Convolutional Neural Networks (CNN) are most commonly used. However, due to their complexity, there are many problems related but not limited to optimizing network parameters, avoiding overfitting and ensuring good...
-
Problems of construction projects regarding historic road bridges
PublikacjaThe paper describe the comparison of different approaches to reconstruction and the problems in the selection of implementation for a historic bridge over the Vistula River in Tczew. A compromise reconstruction is shown, taking technical, historical and aesthetic aspects into account, as well as needs of the local community.
-
Low-fidelity model considerations for simulation-based optimisation of miniaturised wideband antennas
PublikacjaHere, variable-fidelity electromagnetic (EM)-based design optimisation of miniaturised antennas is discussed. The authors focus on an appropriate selection of discretisation density of the low-fidelity EM model, which results in good performance of the optimisation algorithm in terms of its computational complexity and reliability. Trust-region gradient search with low-fidelity model corrected by means of non-linear frequency scaling...
-
Comparative Analysis of Numerical and Experimental Studies of the Airflow Around the Sample of Urban Development
PublikacjaIn this paper, on the background of a short overview of the recent advances in the field of Environmental Wind Engineering (EWE), a comparison of wind tunnel experiment and numerical simulation for some cases of airflow around an urban layout have been reported. The purpose of the study is quantitative and qualitative comparison of measurements in the wind tunnel as well as numerical simulation using Ansys Fluent software. The...
-
Kinetics of the crosslinking reaction between genipin and chitosan solutions
PublikacjaThe kinetics of the chitosan crosslinking reaction with genipin was examined. The strong relationship was found between crosslinking agent concentration, chitosan concentration, temperature and gelling time. Data obtained will be used in the proper selection of optimal genipin concentration for crosslinking chitosan solutions.
-
Installation of Compensators in the Power System Transmission Grid
PublikacjaThe article discusses issues of reactive power compensation in transmission grids, with particular focus on the selection of compensator locations and basic parameters. Attention was focused on modern power electronics systems that ensure full automatic compensator adjustment to voltage or power criteria.
-
Fuel, Oils and Greases, W, E, sem.03, zimowy 22/23
Kursy OnlineDivision and origin of fuels. Fossil energy resources in Poland and in the world. Production and structure of fuel consumption. Main directions of crude oil processing. Classification and physical properties of gaseous and liquid fuels - natural gas, gasoline, kerosene, diesel oil, heating oil. Classification and characteristic indicators of solid fuels - hard coal, lignite, peat. Fuel contaminants and methods of their removal....
-
Technologies for deodorization of malodorous gases
PublikacjaThere is an increasing number of citizens’complaints about odor nuisance due to production or service activity. High socialawareness imposes pressure on entrepreneurs and service providers forcing them to undertake effective steps aimed at minimi-zation of the effects of their activity, also with respect to emission of malodorous substances. The article presents informationabout various technologies used for gas deodorization....
-
Standards with cybersecurity controls for smart grid - A systematic analysis
PublikacjaIn recent years numerous standards related to the cybersecurity of smart grids have been published, which led to the challenge for operators in obtaining indications that match their specific objectives and contexts. Although several studies approached this problem by providing more or less comprehensive surveys and overviews of smart grid cybersecurity standards, none of them was dedicated to the actual and important subject of...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublikacjaThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Failure of austenitic stainless steel tubes during steam generator operation
PublikacjaThe article presents the failure process of austenitic stainless steels used in power devices, such as heat exchangers, steam generators, in terms of local corrosion: pitting, stress and intergranular corrosion, paying particular attention to welded joints area. The effect of steel chemical composition, microstructure, welding process and work environment was analyzed. The second part of the article presents the results of the...
-
Marine autonomous surface ship - control system configuration
PublikacjaThis paper addresses the problem of marine autonomous surface ship (MASS) control. The contribution of the paper is the development of a control system configuration, done assuming fully autonomous MASS operation under distinct operational conditions. The overview of hardware and software selection is included.
-
An Instantaneous Engine Speed Estimation Method Using Multiple Matching Synchrosqueezing Transform
PublikacjaInstantaneous rotational speed measurement of the engine is crucial in routine inspection and maintenance of an automobile engine. Since the contact measurement of rotational speed is not always available, the vibration measurement has been used for noncontact rotational speed estimation methods. Unfortunately, the accuracy of the noncontact estimation methods by analyzing engine vibration frequency is not satisfactory due to the...
-
Risk Management in "Agile" methodologies using the example of Scrum and the IBM Rational Team Concert tool
PublikacjaProject risk is one of the key areas which should be subjected to a thorough analysis in any IT project. Project managers undertake steps to minimize risks, both in terms of organization (matching people to tasks or roles) as well as in terms of technology (using appropriate tools for the management and execution of tasks). Every method of project management defines and describes the processes and techniques related to knowledge...
-
Human memory enhancement through electrical stimulation in the temporal cortex
PublikacjaDirect electrical stimulation of the human brain can elicit sensory and motor perceptions as well as recall of memories. Stimulating higher order association areas of the lateral temporal cortex in particular was reported to activate visual and auditory memory representations of past experiences (Penfield and Perot, 1963). We hypothesized that this effect could be used to modulate memory processing. Recent attempts at memory enhancement...
-
Multicriteria Optimization Approach to Design and Operation of District Heating Supply System over its Life Cycle
PublikacjaDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). In the paper a method for optimized selection of design and operating parameters of long distance Heat Transportation System (HTS) is proposed. The method allows for evaluation of feasibility and effectivity of heat transportation...
-
New semi-causal and noncausal techniques for detection of impulsive disturbances in multivariate signals with audio applications
PublikacjaThis paper deals with the problem of localization of impulsive disturbances in nonstationary multivariate signals. Both unidirectional and bidirectional (noncausal) detection schemes are proposed. It is shown that the strengthened pulse detection rule, which combines analysis of one-step-ahead signal prediction errors with critical evaluation of leave-one-out signal interpolation errors, allows one to noticeably improve detection results...
-
Krzysztof Nyka dr hab. inż.
OsobyKrzysztof Nyka, absolwent Wydziału Elektroniki Telekomunikacji i Informatyki Politechniki Gdańskiej (WETI PG), gdzie uzyskał tytuł magistra inżyniera (1986, telekomunikacja) stopień doktora nauk technicznych (2002, elektronika) i doktora habilitowanego (2020 automatyka, elektronika i elektrotechnika). Obecnie jest zatrudniony na stanowisku profesora uczelni w Katedrze Inżynierii Mikrofalowej i Antenowej WETI PG. Zainteresowania...
-
Coupling coefficients for the space group of the hexagonal close-packed structure
PublikacjaWe have computed the Clebsch-Gordan coefficients of the representations for the space group of the hexagonal close-packed structure for the points:V, A, H, K, L, M. We enumerate all arms of the wave vector stars and all wave vector selection rules.
-
Potentiometric Solid-Contact Ion-Selective Electrode for Determination of Thiocyanate in Human Saliva
PublikacjaA new solid-contact potentiometric ion-selective electrode for the determination of SCN− (SCN-ISE) has been described. Synthesized phosphonium derivative of calix[4]arene was used as a charged ionophore. The research included selection of the ion-selective membrane composition, determination of the ISEs metrological parameters and SCN-ISE application for thiocyanate determination in human saliva. Preparation of the ISEs included...
-
The methodology of design of satellite working mechanism of positive displacement machine
PublikacjaIn this paper is described a methodology of design of satellite mechanism consisting of two noncircular gears (externally toothed rotor and internally toothed curvature) and circular gears (satellites). In the presented methodology is assumed that the rotor pitch line is known, and the curvature pitch line is necessary to designate. The presented methodology applies to mechanisms for which the number of the curvature humps is at...
-
Rotor Blade Geometry Optimisation in Kaplan Turbine
PublikacjaThe paper presents the description of method and results of rotor blade shape optimisation. The rotor blading constitutes a part ofturbine flow path. Optimisation consists in selection of the shape that minimises ratio of polytrophic loss. Shape of the blade isdefined by the mean camber line and thickness of the airfoil. Thickness is distributed around the camber line based on the ratio ofdistribution. Global optimisation was done...
-
THE USE OF MORPHOLOGICAL FILTERS AND GRANULOMETRIC METHOD TO ANALYZE THE MOVEMENT OF THE MOLECULES IN THE SEA WATER OF THE SOUTHERN BALTIC SEA
PublikacjaModern granulometry opens a new way of analysing images by means of morphological filters. In this paper a closer look has been presented on the problem of interpreting information about the features and conditions of marine environment from images taken at the sea coast and shallow water. Using this method allows for example selection of the objects on the image according to the differences in shape. Processes occurring in the...
-
A New Type of Macro-Elements for Efficient Two-Dimensional FEM Analysis
PublikacjaThis letter deals with a model order reduction technique applicable for driven and eigenvalue problems solved using the finite element method (FEM). It allows one to efficiently compute electromagnetic parameters of structures comprising small features that require strong local mesh refinement. The subdomains of very fine mesh are separated from the global domain as so called macro-elements that undergo model reduction. The macro-elements...
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublikacjaAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Selecting Features with SVM
PublikacjaA common problem with feature selection is to establish how many features should be retained at least so that important information is not lost. We describe a method for choosing this number that makes use of Support Vector Machines. The method is based on controlling an angle by which the decision hyperplane is tilt due to feature selection. Experiments were performed on three text datasets generated from a Wikipedia dump. Amount...
-
High Efficiency Dual-Active-Bridge Converter with Triple-Phase-Shift Control for Battery Charger of Electric Vehicles
PublikacjaAn optimal modulation scheme with triple-phase-shift (TPS) control could increase the efficiency in the entire load range for a dual-active-bridge (DAB) converter under wide output voltage range conditions. Therefore, this study proposes a convergent approach to TPS mode selection, coupled with an optimal modulation scheme, ensuring the circuit’s efficiency over the entire range in the realm of a high-power and high-efficiency...
-
CFD-based evaluation of current-carrying capacity of power cables installed in free air
PublikacjaEvaluation of current-carrying capacity of power cables and selection of cross-sectional area of their conductors are mainly performed in accordance with requirements of EN, IEC or IEEE standards. However, these standards do not provide all methods of cables installation and location which occur in practice. Thus, in some cases, performance of advanced modeling of various thermal phenomena, affecting power cables current-carrying...
-
Lamp of adjustable spectrum for photographic usage
PublikacjaPhotography is a unique rapidly growing interdisciplinary field encompassing aspects of science, art and technology. Expectations of photographers are steadily increasing with the development of technology. One of the areas playing a crucial role in photography is lighting. Consequently, several types of light sources for photographic use have been developed. The ongoing research in this field concentrates on lamps with tunable...
-
Intelligent Knowledge-Base Model for IT Support Organization Evolution
PublikacjaThe goal of the paper is building the knowledge-based model for predicting the state of the IT support organization. These organizations, critical for development of various business sectors, are facing the problem of their transformation. It is the result of the fundamental change in the role of the IT organizations in the current economy. The complexity of the processes, the difficulty adjusting the operations and limited ability...
-
Modeling and control of a redundantly actuated variable mass 3RRR planar manipulator controlled by a model-based feedforward and a model-based-proportional-derivative feedforward–feedback controller
PublikacjaIn the paper, dynamics of a complex mechatronics system is considered. A redundantly actuated planar manipulator is the base of the mechanical part of it. It is a 3RRR 1 platform based parallel manipulator. To control its trajectory, a model-based feedforward controller is employed. Three aspects are fundamental in the presented investigations. The first focus is on development of an accurate numerical model used to solve the inverse...
-
Pupil size reflects successful encoding and recall of memory in humans
PublikacjaPupil responses are known to indicate brain processes involved in perception, attention and decision-making. They can provide an accessible biomarker of human memory performance and cognitive states in general. Here we investigated changes in the pupil size during encoding and recall of word lists. Consistent patterns in the pupil response were found across and within distinct phases of the free recall task. The pupil was most...
-
Ontology Engineering Aspects in the Intelligent Systems Development
PublikacjaThe ontology engineering encompasses both, artificial intelligence methods and software engineering discipline. The paper tries to address a selection of aspects pertaining to development activities such as choice of the environmental framework, functionality description, specification methods and roles definition. Authors refer to the ontology development projects they were involved in.
-
A Simulation Model for Risk and Pricing Competition in the Retail Lending Market
PublikacjaWe propose a simulation model of the retail lending market with two types of agents: borrowers searching for low interest rates and lenders competing through risk-based pricing. We show that individual banks observe adverse selection, even if every lender applies the same pricing strategy and a credit scoring model of comparable discrimination power. Additionally, the model justifies the reverse-S shape of the response rate curve....
-
Unsupervised machine-learning classification of electrophysiologically active electrodes during human cognitive task performance
PublikacjaIdentification of active electrodes that record task-relevant neurophysiological activity is needed for clinical and industrial applications as well as for investigating brain functions. We developed an unsupervised, fully automated approach to classify active electrodes showing event-related intracranial EEG (iEEG) responses from 115 patients performing a free recall verbal memory task. Our approach employed new interpretable...
-
Model dynamic electrochemical impedance spectroscopy (DEIS) results obtained with various DC polarization rates
Dane BadawczeThe dataset contains results of model dynamic electrochemical impedance spectroscopy studies carried out on a setup of 10 diodes in series, which were connected in parallel with a condenser. The impedance data were acquired every 1 s (the analytic window length for Fourier Transform was 1 s). The model system was polarized between 0 and +8 V with DEIS...
-
How Can We Identify Electrophysiological iEEG Activities Associated with Cognitive Functions?
PublikacjaElectrophysiological activities of the brain are engaged in its various functions and give rise to a wide spectrum of low and high frequency oscillations in the intracranial EEG (iEEG) signals, commonly known as the brain waves. The iEEG spectral activities are distributed across networks of cortical and subcortical areas arranged into hierarchical processing streams. It remains a major challenge to identify these activities in...
-
Decision support system for design of long distance heat transportation system
PublikacjaDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). The paper proposes a Decision Support System (DSS) for optimized selection of design and operating parameters of a long distance Heat Transportation System (HTS). The method allows for evaluation of feasibility and effectiveness...
-
Janusz Kozak prof. dr hab. inż.
OsobyDr hab. inż. Janusz Kozak Dziekan Wydziału Oceanotechniki i Okrętownictwa Politechniki Gdańskiej Urodzony: 04.07.1953 w Pucku Absolwent Technikum Budowy Okrętów „Conradinum” w Gdańsku, 1973. Absolwent Instytutu Okrętowego PG, 1978. Po ukończeniu studiów praca w Stoczni Gdynia, a od roku 1980 w Katedrze Technologii Okrętów Instytutu Okrętowego a później Wydziału Oceanotechniki i Okrętownictwa Politechniki Gdańskiej kolejno na...
-
LSTM-based method for LOS/NLOS identification in an indoor environment
PublikacjaDue to the multipath propagation, harsh indoor environment significantly impacts transmitted signals which may adversely affect the quality of the radiocommunication services, with focus on the real-time ones. This negative effect may be significantly reduced (e.g. resources management and allocation) or compensated (e.g. correction of position estimation in radiolocalisation) by the LOS/NLOS identification algorithm. This paper...
-
Macromodeling techniques for accelerated finite element analysis
PublikacjaThis paper deals with the Model Order Reduction applied locally in the Finite Element Method (FEM) analysis. Due to the reduction process, blocks of FEM system matrices associated with selected subregions of the computational domain are projected onto the subspaces spanned by the vectors of suited orthogonal projection basis. In effect, large and sparse FEM matrices are replaced with small and dense ones, called macromodels. This...
-
Detection, identification and determination of chiral pharmaceutical residues in wastewater: Problems and challenges
PublikacjaChiral pharmaceuticals (CPs) are widely used in different areas of human life, thus they are frequentlydetected in different ecosystems. However, before CPs reach the environment, wastewater is subjected todifferent treatment processes in order to remove them. Nevertheless, such processes may affect thechirality of CPs, thus it is very important to monitor CP levels during the wastewater treatment.This review addresses the present...
-
Rigid finite elements and multibody modeling in analyses of a robot shaped elastic/plastic deformations of a beam
PublikacjaDynamics analysis of a system composed of a parallel manipulator and of an elastic beam is presented in the paper. Classic 3RRR parallel manipulator is considered and used to deform the beam. Elasto-plastic deformations are investigated. Rigid-finite-elements technique is employed to deal with dynamics of the beam. A multibody structure is associated with the introduced hybrid system in order to model its dynamics. Idea of the...