displaying 1000 best results Help
Search results for: standard reduction potential
-
Reduction of road traffic noise by source measures — present and future strategies
PublicationThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
Thermohydraulic maldistribution reduction in mini heat exchangers
PublicationA detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm × 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave manifolds in Z-type flow configuration. The working medium was ethanol and the mass flow rate was 5 × 10−4 kg/s. Both sections were heated from the bottom side. Heat flux of 10 000 W/m2 and 5000 W/m2 was...
-
Experiences and Challenges in Fatality Reduction on Polish Roads
PublicationAccording to the UN, road safety is the key to achieving sustainable development goals, yet the complexity of how road accidents happen makes this a difficult challenge leaving many countries struggling with the problem. For years, Poland has infamously been one of the EU’s top countries for road-accident fatality rates. Despite that, it has made significant progress in the last thirty years with a fatality reduction of more than...
-
The Method of reduction of aerodynamic forces generated in turbine blade seals
PublicationThe distibution of pressure in the seal gaps does not only affect the so called '' leakage losses'' and the turbine stage overall efficiency but also plays an important role in the generation of aerodynamic forces which may cause self-excited rotor vibrations. The paper describes a chamber seal applied for the reduction of the aerodynamic forces created in shroud seals. This kind of turbine seal was patented and tested.
-
Computational and experimental evaluation of view out according to European Standard EN17037.
PublicationThis paper presents an experimental evaluation of view out based on EN17037:2018 Daylight in Buildings within an educational building. The primary motivation to conduct the research was an introduction of a view out appraisal criteria by the mentioned standard. The study gives insights into the following: (i) the use of computational evaluation of an outside view according to the EN17037 criteria (ii) the use of the direct simultaneous...
-
Application of polymer element in reduction of temporary steel grandstand vibrations
PublicationThe numerical analysis focused on reduction of vibrations of a temporary steel scaffolding grandstand has been conducted in this paper. These types of structures are regularly subjected to dynamic loads which, in conjunction with light and quite slender structural members, may induce dangerous vibrations. To increase their safety, temporary steel grandstands are usually strengthened with the diagonal stiffeners of tubular cross...
-
Development of techniques of generation of gaseous standard mixtures
PublicationW pracy przedstawiono informacje dotyczące: klasyfikacji znanych technik sporządzania gazowych mieszanin wzorcowych oraz omówienia technik najszerzej wykorzystywanych wraz z przedstawieniem odpowiednich schematów zestawów aparaturowych. Przedstawiono również informacje na temat nowego podejścia do zagadnienia sporządzania gazowych mieszanin wzorcowych. W tym przypadku strumień składnika mierzonego (analitu) jest otrzymywany w procesie...
-
Non-standard binary weighted number systems
PublicationZdefiniowano szeroką klasę binarnych systemów wagowych. Wszystkie sa wzajemnie jednoznaczne ale mogą być zupełne lub niezupełne. Jeżeli wagi systemu są kolejnymi liczbami naturalnymi to system jest minimalny.Jesli wagi sa kolejnymi potęgami podstawy Z to system jest maksymalny. W przestrzeni między tymi systemami znajdują się inne systemy binarne. Kilka z nich przedstawiono w referacie.
-
POTENTIAL ANALYSIS
Journals -
Size Reduction of Microwave Couplers by EM-Driven Optimization
PublicationThis work addresses simulation-driven design optimization of compact microwave couplers that explicitly aims at circuit footprint area reduction. The penalty function approach allows us to minimize the area of the circuit while ensuring a proper power division between the output ports and providing a sufficient bandwidth with respect to return loss and isolation around the operating frequency. Computational cost of the optimization...
-
Performance analysis of standard and modified EY-NPMA channel access algo-rithms
PublicationPodczas minionego 10-ciolecia notuje się szybki rozwój lokalnych sieci bezprzewodowych (WLANy). Proponowane rozwiązania dotyczą zarówno sieci opartych o przesył komórek (zgodnych z ATM), jak i sieci pakietowych (zgodnych z E-thernetem). Po rozważeniu drugiego z wymienionych typów sieci, wydaje się dzisiaj, iż pakietowe WLANy będą oparte głównie na dwóch standardach, mianowicie: IEEE 802.11 [6]) - wykorzystującym protokół dostępu...
-
Domain Reduction in Hybrid Technique for Electromagnetic Wave Scattering Problems
PublicationThis paper proposes a combination of the field matching technique, finite element method and generalized impedance matrix, the main idea of which is to reduce the computational domain by surrounding a scatterer with the smallest convex shape and applying the field matching technique. This approach can be applied for arbitrary shaped scatterers and types of materials and allows for the reduction of the computational domain. In order...
-
Hydraulic potential of the Lower Vistula (Poland)
PublicationThe Vistula is the largest river in Poland. Lower Vistula (part of the river discussed in this paper) is almost four hundred kilometers long river section extending from the tributary Narew to the outflow to the Baltic Sea. In the 17th century the Vistula was the most navigable river in Europe. After partitioning of Poland the Vistula lost its significance. Now the Lower Vistula should provide a navigation connection to the Europe...
-
A study on the protection of methionine and the reduction of methionine sulfoxide in methionine-containing analogues of the growth-modeling factor Gly-His-Lys
PublicationThe protection of methionine and the reduction of methionine sulfoxide in methionine-containing analogues of Gly-His-Lys are described. The peptides were synthesized by a solid-phase method using the standard Fmoc procedure. Simultaneous deprotection of the peptide side chain and liberation from the resin were achieved using an appropriate TFA cocktail. The TFA cocktail was selected to minimize oxidation of the methionine residue....
-
Potential energy curves of LiCs dimer
Open Research DataThis data presents potential energy curves of LiCs dimer in Hund's case (a). Calculated using Born-Oppenheimer approximation with scalar relativistic effects are included via large effective core potentials. Custom basis sets, core polarization potentials and MRCI method are used to accurately describe electron correlation. Dataset consists of 22 potential...
-
Potential energy curves of NaRb dimer
Open Research DataThis data presents potential energy curves of NaRb dimer in Hund's case (a). Calculated using Born-Oppenheimer approximation with scalar relativistic effects are included via large effective core potentials. Core polarization potentials and MRCI method is used to describe electron correlation. Dataset consists of 18 potential energy curves of ground...
-
The reduction of auxiliaries power demand: The challenge for electromobility in public transportation
PublicationAn important role in the consumption of electric energy in urban transport are non-traction needs (auxiliaries), the main part of which is heating and air condition (HVAC). Auxiliaries are responsible for almost half of total energy consumption (normal weather conditions) and in the winter (or hot summer) it reaches up to 70% in daily scale. The reduction of energy used for non-traction needs is currently the main challenge related...
-
Effect of Vascular Lumen Reduction on the Performance and Energy Consumption of an Innovative Implantable LVAD
PublicationThis paper presents the results of a study on the effect of vascular lumen reduction on the performance of an innovative implantable LVAD (left ventricular assist device). It details the pressures in the individual cardiac chambers as a function of device frequency. In addition, mass flow rates and energy consumption of the device are examined, varying with lumen reduction and operating frequency. While the lumen reduction of the...
-
Improving Clairvoyant: reduction algorithm resilient to imbalanced process arrival patterns
PublicationThe Clairvoyant algorithm proposed in “A novel MPI reduction algorithm resilient to imbalances in process arrival times” was analyzed, commented and improved. The comments concern handling certain edge cases in the original pseudocode and description, i.e., adding another state of a process, improved cache friendliness more precise complexity estimations and some other issues improving the robustness of the algorithm implementation....
-
Reliable Greedy Multipoint Model-Order Reduction Techniques for Finite-Element Analysis
PublicationA new greedy multipoint model-order reduction algorithm for fast frequency-domain finite-element method simulations of electromagnetic problems is proposed. The location of the expansion points and the size of the projection basis are determined based on a rigorous error estimator. Compared to previous multipoint methods, the quality of the error estimator is significantly improved by ensuring the orthogonality of the projection...
-
Surrogate-Assisted Design of Checkerboard Metasurface for Broadband Radar Cross-Section Reduction
PublicationMetasurfaces have been extensively exploited in stealth applications to reduce radar cross section (RCS). They rely on the manipulation of backward scattering of electromagnetic (EM) waves into various oblique angles. However, arbitrary control of the scattering properties poses a significant challenge as a design task. Yet it is a principal requirement for making RCS reduction possible. This article introduces a surrogate-based...
-
Low-Cost Behavioral Modeling of Antennas by Dimensionality Reduction and Domain Confinement
PublicationBehavioral modeling has been rising in importance in modern antenna design. It is primarily employed to diminish the computational cost of procedures involving massive full-wave electromagnetic (EM) simulations. Cheaper alternative offer surrogate models, yet, setting up data-driven surrogates is impeded by, among others, the curse of dimensionality. This article introduces a novel approach to reduced-cost surrogate modeling of...
-
A Reduction Method for Bathymetric Datasets that Preserves True Coastal Water Geodata
PublicationWater areas occupy over 70 percent of the Earth’s surface and are constantly subject to research and analysis. Often, hydrographic remote sensors are used for such research, which allow for the collection of information on the shape of the water area bottom and the objects located on it. Information about the quality and reliability of the depth data is important, especially during coastal modelling. In-shore areas are liable...
-
Advanced Potential Energy Surfaces for Molecular Simulation
PublicationAdvanced potential energy surfaces are defined as theoretical models that explicitly include many-body effects that transcend the standard fixed-charge, pairwise-additive paradigm typically used in molecular simulation. However, several factors relating to their software implementation have precluded their widespread use in condensed-phase simulations: the computational cost of the theoretical models, a paucity of approximate models...
-
Reduction of measurement data before Digital Terrain Model generation vs. DTM generalisation
PublicationModern data acquisition technologies provide large datasets that are not always necessary in its entirety to properly accomplish the goal of the study. In addition, such datasets are often cumbersome for rational processing, and their processing is time and labour consuming. Therefore, methods that enable to reduce the size of the measurement dataset, such as the generalization of the Digital Terrain Model (DTM) or the reduction...
-
The effectiveness of polymer adhesive in reduction of vibrations of structural members
PublicationIn this paper, the idea of using polymer adhesive as a damping layer is proposed. An experimental study of two aluminium cantilevered beams has been conducted. One of them presents a plain cantilevered beam, while the second one considers two aluminium beams bonded with a polymer adhesive of different thickness (0,5; 1,2; 1,75; 3,1 and 5 mm). The polymer adhesive considered in the study is a specially designed flexible...
-
CENTRAL-FORCE DECOMPOSITION OF THE TERSOFF POTENTIAL
PublicationCentral forces play important role in the analysis of results obtained with particle simulation methods, since they allow evaluating stress fields. In this work we derive expressions for a central-force decompositon of the Tersoff potential, which is often used to describe interatomic interactions in covalently bonded materials. We simplify the obtained expressions and discuss their properties.
-
Fixed Pattern Noise Reduction and Linearity Improvement in Time-Mode CMOS Image Sensors
PublicationIn the paper, a digital clock stopping technique for gain and offset correction in time-mode analog-to-digital converters (ADCs) has been proposed. The technique is dedicated to imagers with massively parallel image acquisition working in the time mode where compensation of dark signal non-uniformity (DSNU) as well as photo-response non-uniformity (PRNU) is critical. Fixed pattern noise (FPN) reduction has been experimentally validated...
-
Topological modifications for performance improvement and size reduction of wideband antenna structures
PublicationCompact antennas belong to the key components of modern communication systems. Their miniaturization is often achieved by introducing appropriate topological changes such as simple ground plane slots or tapered feeds. More sophisticated modifications are rarely considered in the literature because they normally lead to significant increase of the number of tunable parameters, which makes the antenna design process more challenging....
-
Compact 4 × 4 butler matrix with non‐standard phase differences for IoT applications
PublicationButler matrices represent a popular class of feeding networks for antenna arrays. Large dimensions and the lack of flexibility in terms of achievable output phase difference make conventional Butler structures of limited use for modern communication devices. In this work, a compact planar 4 × 4 matrix with non-standard relative phase shifts of –30º, 150º, –120º, and 60º has been proposed. The structure is designed to operate at...
-
Effect of applied standard wood machining fluid on colour and chemical composition of the machined wood surface
PublicationAppropriate monitoring of wood machining processes is a key issue to ensure the expected quality of the processed wood, expected efficiency and minimize energy consumption of production processes. A new trend is the design of environmentally friendly machining fluids. In this paper, as a preliminary study in this field, the effect of applied standard wood machining fluid on changes in the colour and chemical composition of the...
-
Multilevel model order reduction.
PublicationPrezentujemy wielopoziomowy algorytm redukcji rzędu modelu wykorzystany do zwiększenia efektywnosci analizy struktur mikrofalowych metodami siatkowymi.Schemat pozwala tworzyć makromodele zagniezdzone i laczyc te technike z szybkim przemiataniem częstotliwości (FFS). Implementacja metody pokazana jest na przukladzie różnic skończonych w dziedzinie częstotliwości i metody redukcji ENOR, lecz koncept moze być łatwo użyty w innych...
-
Distributed Learning with Data Reduction
Publication -
Substrate Reduction Therapies for Mucopolysaccharidoses
Publication -
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publicationhis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
Multilevel model order reduction with generalized compression of boundaries for 3-d FEM electromagnetic analysis
PublicationThis paper presents a multilevel Model Order Reduction technique for a 3-D electromagnetic Finite Element Method analysis. The reduction process is carried out in a hierarchical way and involves several steps which are repeated at each level. This approach brings about versatility and allows one to efficiently analyze complex electromagnetic structures. In the proposed multilevel reduction the entire computational domain is covered...
-
Potential changes in an electric field and electrolytic corrosion.
PublicationSources have been described of corrosively hazardous electric fields and methods of determination of the corrosion hazard to metal structures caused by electrolytic corrosion. Results of potential and impedance investigations in the field of stray currents flowing out of a tram traction and in the presence of a defined electric field of low frequency have been presented. Uncertainties have been indicated relating to the generally...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Characteristics of an image sensor with early-vision processing fabricated in standard 0.35 µm CMOS technology
PublicationThe article presents measurement results of prototype integrated circuits for acquisition and processing of images in real time. In order to verify a new concept of circuit solutions of analogue image processors, experimental integrated circuits were fabricated. The integrated circuits, designed in a standard 0.35 µm CMOS technology, contain the image sensor and analogue processors that perform low-level convolution-based image...
-
Potential direction of changes in tax incentives
Open Research DataThe study conducted on a group of 259 entrepreneurs concerned exploring the potential direction of changes in the scope of the tax incentive system in Poland. The results of the study include answers to questions about the mechanisms of tax reliefs used so far, as well as the potentialn direction of changes in this respect.
-
Radio programowalne - przyszły standard inteligentnego systemu radiokomunikacyjnego
PublicationW pracy przedstawiono całkowicie nowatorską koncepcję programowalnego systemu radiokomunikacyjnego zwłaszcza w odniesieniu do inteligentnego terminala użytkownika w tym systemie. Na wstępie omówiono platformę sprzętową takiego rozwiązania. Następnie przedstawiono rozwiązanie systemowe platformy informatycznej, poczynając od jej charakterystyki funkcjonalnej, poprzez opis środowiska programowego koniecznego do realizacji niezbędnych...
-
Possibilities of applying standard tools of promotion in place marketing
PublicationThe purpose of this article is to present the tools of promotion that can be used by local government units in the developing and implementing of marketing strategies. The article evaluates a set of four basic tools of promotion comprising advertising, public relations and publicity, sales promotion and personal selling. This group was supplemented by direct marketing, presented from the point of view of communication via the Internet.
-
General concept of reduction process for big data obtained by interferometric methods
PublicationInterferometric sonar systems apply the phase content of the sonar signal to measure the angle of a wave front returned from the seafloor or from a target. It collect a big data – datasets that are so large or complex that traditional data processing application software is inadequate to deal with them. The recording a large number of data is associated with the difficulty of their efficient use. So data have to be reduced. The main...
-
Objective relaxation algorithm for reliable simulation-driven size reduction of antenna structure
PublicationThis letter investigates reliable size reduction of antennas through electromagnetic-driven optimization. It is demonstrated that conventional formulation of the design task by direct footprint miniaturization with imposing constraints on electrical performance parameters may not lead to optimum results. The reason is that—in a typical antenna structure—only a few geometry parameters explicitly determine the antenna footprint,...
-
The Influence of Articular Cartilage Thickness Reduction on Meniscus Biomechanics
PublicationObjective Evaluation of the biomechanical interaction between meniscus and cartilage in medial compartment knee osteoarthritis. Methods The finite element method was used to simulate knee joint contact mechanics. Three knee models were created on the basis of knee geometry from the Open Knee project. We reduced the thickness of medial cartilages in the intact knee model by approximately 50% to obtain a medial knee osteoarthritis...
-
DES - polarity, pH and antioxidant potential
Open Research DataThis physicochemical properties of selected deep eutectic solvents (DES) were tested. Polarity is important for extraction efficiency. The values of pH can importantly affect growing of bacteria and yeasts strains. Total phenolic content, DPPH and FRAP methods were used for determination of antioxidant potential of the extract produced with DES.
-
Quasirelativistic potential energy curves of NaRb dimer
Open Research DataThis data presents potential energy curves of NaRb dimer, that include spin-orbit interaction, in Hund's case (c). Calculated using Born-Oppenheimer approximation with relativistic effects included via large spin-orbit effective core potentials. Custom basis sets, core polarization potentials and MRCI method are used to accurately describe electron...
-
Size-Reduction-Oriented Design of Compact CPW-Fed UWB Monopole Antenna
PublicationA structure and design optimization of compact CPW-fed UWB monopole antenna is presented. Explicit size reduction through constrained numerical optimization of all relevant geometry parameters of the structure leads to a very small footprint of only 321 mm2. At the same time, a very wide antenna bandwidth is achieved from 3.1 GHz to 17 GHz.
-
Therapeutic Potential of Multifunctional Tacrine Analogues
PublicationTacrine is a potent inhibitor of cholinesterases (acetylcholinesterase and butyrylcholinesterase) that shows limiting clinical application by liver toxicity. In spite of this, analogues of tacrine are considered as a model inhibitor of cholinesterases in the therapy of Alzheimer’s disease. The interest in these compounds is mainly related to a high variety of their structure and biological properties. In the present review, we...
-
Evolutionary sets of safe ship trajectories with speed reduction manoeuvres within traffic separation schemes
PublicationIn the previous paper the author presented the evolutionary ship trajectory planning method designed to support Traffic Separation Schemes (TSS). This time the extensions of this method are described which allow to combine evolutionary trajectory planning with speed reduction manoeuvres. On TSS regions with higher than usual density of traffic and smaller distances between ships, the course alterations alone are not always sufficient...
-
Adiabatic potential energy curves of the KRb molecule
Open Research DataAdiabatic potential energy curves (APEC) of the singlet (s) and triplet (t) Sigma+, Sigma-, Pi, and Delta electronic states have been calculated for the KRb molecule. Presented APECs correlate with 11 atomic asymptotes, starting from ground K(4s)+Rb(5s) atomic limit and ending on double-excited K(4p)+Rb(5p) atomic limit. All results of the presented...
-
Exploring the cocrystallization potential of urea and benzamide
PublicationThe cocrystallization landscape of benzamide and urea interacting with aliphatic and aromatic carboxylic acids was studied both experimentally and theoretically. Ten new cocrystals of benzamide were synthesized using an oriented samples approach via a fast dropped evaporation technique. Information about types of known bi-component cocrystals augmented with knowledge of simple binary eutectic mixtures was used for the analysis...
-
Experimental validation of the rolling resistance measurement method including updated draft standard
PublicationThe main objective of ROSANNE is the harmonisation and standardisation of the measurement of skid resistance, noise emission and rolling resistance of road pavements. Regarding rolling resistance characterisation, a draft for standardization of a harmonized procedure for classification of road surfaces across Europe has been prepared within WP3 (deliverable 3.5). The procedure deals with the direct measurement on real roads of...
-
Design space reduction and variable-fidelity EM simulations for feasible Pareto optimization of antennas
PublicationA computationally efficient procedure for multi-objective optimization of antenna structures is presented. In our approach, a response surface approximation (RSA) model created from sampled coarse-discretization EM antenna simulations is utilized to yield an initial set of Pareto-optimal designs using a multi-objective evolutionary algorithm. The final Pareto front representation for the high-fidelity model is obtained using surrogate-based...
-
Feature Reduction Using Similarity Measure in Object Detector Learning with Haar-like Features
PublicationThis paper presents two methods of training complexity reduction by additional selection of features to check in object detector training task by AdaBoost training algorithm. In the first method, the features with weak performance at first weak classifier building process are reduced based on a list of features sorted by minimum weighted error. In the second method the feature similarity measures are used to throw away that features...
-
New potential functions for greedy independence and coloring
PublicationA potential function $f_G$ of a finite, simple and undirected graph $G=(V,E)$ is an arbitrary function $f_G : V(G) \rightarrow \mathbb{N}_0$ that assigns a nonnegative integer to every vertex of a graph $G$. In this paper we define the iterative process of computing the step potential function $q_G$ such that $q_G(v)\leq d_G(v)$ for all $v\in V(G)$. We use this function in the development of new Caro-Wei-type and Brooks-type...
-
Determination of terpene profiles in potential superfruits
PublicationThe aim of this work was to characterize and compare the profiles of volatile terpenes in four potential superfruits. These profiles were determined using headspace solid-phase microextraction coupled with comprehensive two-dimensional gas chromatography linked to time-of-flight mass spectrometry. The proposed technique allowed the separation and identification of 79 terpenes present in cape gooseberry, crabapple, cherry silver...
-
ASSESSMENT OF TOXIC EFFECT AND ENDOCRINE POTENTIAL OF FOOD PACKAGES EXTRACTS
PublicationIn the scientific literature related to the widely understood issue of packaging materials designed to have contact with food there is much information on raw materials used for their production, their physiochemical properties, types and parameters. There is also a great number of publications on the management and disposal of used packaging. Unfortunately, not much attention is given to the matters concerning migration of toxic...
-
Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials
PublicationThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were...
-
Size reduction of ultra-wideband antennas with efficiency and matching constraints
PublicationAntenna design is a multifaceted task that involves handling of various performance figures concerning both electrical performance of the structure as well as its geometry. Simultaneous control of several objectives through rigorous optimization is very challenging and virtually impossible through conventional approaches such as parameter sweeping. In this work, we investigate size reduction of ultra‐wideband antenna structures...
-
ECHOES REDUCTION DURING DIGITAL DATA TRANSMISSION IN HYDROACOUSTIC CHANNEL – LABORATORY EXPERIMENT
PublicationThe possibility of using a hydroacoustic channel for digital data transmission is very limited. This is due to the effect of multipath propagation of the emitted acoustic wave and the damping of the mechanical wave in this medium, which increase with frequency. The first of these phenomena results in inter-symbol interference disturbances in data transmission systems, including even hundreds of symbols. Due to the number of reflections...
-
Communication Model Order Reduction in Hybrid Methods Involving Generalized Impedance Matrix
PublicationA novel strategy for the efficient analysis of frequency-domain scattering electromagnetic problems in open and closed domains is presented. A fully automatic model-order reduction technique, called the enhanced reduced-basis method, is applied to increase the efficiency of the hybrid approach, which combines the finite-element and mode-matching methods. Numerical tests show that the proposed algorithm yields reliable and highly...
-
Kinetic analysis of the reduction of a ternary system of Bi, Sb and Te oxides by hydrogen for BiSbTe3 synthesis
PublicationReduction in a hydrogen atmosphere of Bi2O3, Sb2O3 and TeO2 mixes oxides for the synthesis of BiSbTe3 was analysed. The reduction reactions of Sb2O3 and Sb2O4 oxides, as well as Bi2O3+Sb2O3 and Sb2O3+3TeO2 mix- tures, were also evaluated. The reduction of Sb2O4 is investigated for the first time. The reactions of the mixed oxides systems also were not the subject of research so far despite being used for synthesis of the (Bi,Sb)2Te3...
-
Influence of reduction process on the structural and mechanical properties of (Pb,Bi)-(Si,Ge)-O oxide glasses
PublicationThe effect of the reduction process in H2 at 380 °C on the microstructure and elemental composition of a glass Bi0.4Pb0.2Si0.4Ox has been investigated. It has been shown that after reduction a clearly separated top layer with a thickness of approx. 50 µm was formed on the surface of the sample. This layer is depleted of oxygen and has higher electrical conductivity than the interior of the glass. It has also been found that some...
-
Efficient analysis of structures with rotatable elements using model order reduction
PublicationThis paper presents a novel full-wave technique which allows for a fast 3D finite element analysis of waveguide structures containing rotatable tuning elements of arbitrary shapes. Rotation of these elements changes the resonant frequencies of the structure, which can be used in the tuning process to obtain the S-characteristics desired for the device. For fast commutations of the response as the tuning elements are rotated, the...
-
Geometry Parametric Model Order Reduction with Randomly Generated Projection Bases
PublicationIn this work, a reduced-order model for geometry parameters and fast frequency sweep is proposed. The Finite Element Method is used to solve time-harmonic Maxwell’s equations. Taking into account the electromagnetic field does not arbitrarily vary as a function of frequency and geometry parameters, a low dimension system manifold is identified. Thus, the original Finite Element problem can be approximated by a model of reduced...
-
Influence of datasets decreased by applying reduction and generation methods on Digital Terrain Models
PublicationThe number of point clouds provided by LiDAR technology can be sometimes seen as a problem in development and further processing for given purposes (e.g. Digital Terrain Model (DTM) generation). Therefore, there is still a need to reduce the obtained big datasets. Reducing can be done, inter alia, by reducing the size of the set or by generating the set. This paper presents two variants of the reduction of point clouds in order...
-
Comparison of Compact Reduced Basis Method with Different Model Order Reduction Techniques
PublicationDifferent strategies suitable to compare the performance of different model order reduction techniques for fast frequency sweep in finite element analysis in Electromagnetics are proposed and studied in this work. A Frobenius norm error measure is used to describe how good job a reduced-order model is doing with respect to the true system response. In addition, the transfer function correct behavior is monitored by studying the...
-
Born-Oppenheimer potential energy curves of the NaK molecule
Open Research DataAdiabatic potential energy curves (APEC) of the singlet (s) and triplet (t) Sigma+, Pi, and Delta electronic states have been calculated for the NaK molecule. All results of the presented molecular states have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials describing the interaction...
-
Experimental study on the effectiveness of polymer dampers in reduction of structural vibrations
PublicationVibrations of civil engineering structures, generated by dynamic loads, may be very dangerous to the structures themselves as well as may have significant influence on human perception and comfort. A number of different methods have been proposed in order to minimize such situations. This concern newly designed structures as well as those which dynamic properties have to be modified due to problems with excessive vibrations. One...
-
Experimental study on effectiveness of polymer dampers in reduction of structural vibrations
PublicationVibrations of civil engineering structures, generated by dynamic loads, may be very dangerous to the structures themselves as well as may have significant influence on human perception and comfort. A number of different methods have been proposed in order to minimize such situations. This concern newly designed structures as well as those which dynamic properties have to be modified due to problems with excessive vibrations. One...
-
The potential of web awareness as a determinant of dually defined customer value
PublicationIn the conditions of increasing demand barrier, the enterprise’s basic capital is customers. From an enterprise point of view, this means the need to create a dual perceived and defined customer value which remains related to market value (income and development potential) and customer resource value (reference, information and cooperative potential). The progressing digitisation process transfers business processes, and thus relationships, into...
-
Bacteriophages as potential tools for use in antimicrobial therapy and vaccine development
PublicationThe constantly growing number of people suffering from bacterial, viral, or fungal infections, parasitic diseases, and cancers prompts the search for innovative methods of disease prevention and treatment, especially based on vaccines and targeted therapy. An additional problem is the global threat to humanity resulting from the increasing resistance of bacteria to commonly used antibiotics. Conventional vaccines based on bacteria...
-
The reduction of vibrations in circular sawing machines
PublicationThe presented in this paper the main objectives of the research were to explore vibrations signals of the main spindle system, the machine tool body and a circular saw to extract informative features for assessment of the designs of the panel saw Fx3 and its follower Fx550.Even though the main spindle of the new table sliding saw Fx550 has its rotational speeds larger about 20% in comparison to the Fx3, peak values of the vibrational...
-
Exhaust gas temperature measurements in diagnostics of turbocharged marine internal combustion engines. Part I. Standard measurements.
PublicationThe article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard...
-
Rotational Design Space Reduction for Cost-Efficient Multi-Objective Antenna Optimization
PublicationCost-efficient multi-objective design of antenna structures is presented. Our approach is based on design space reduction algorithm using auxiliary single-objective optimization runs and coordinate system rotation. The initial set of Pareto-optimal solutions is obtained by optimizing a response surface approximation model established in the reduced space using coarse-discretization EM simulation data. The optimization engine is...
-
Design of standard cells library for UMC L130E FSG process
Publication -
WiMAX - nowy standard szerokopasmowych sieci bezprzewodowych (Cześć 1)
PublicationW artykule przedstawiono historię powstania i rozwoju, główne założenia oraz modele zastosowania standardu IEEE 802.16 (WiMAX). Zaprezentowano architekturę standardu, obejmującą rozwiązania warstwy fizycznej oraz warstwy łącza danych, w obecnej wersji 802.16-2004. Opisano perspektywy rozwoju standardu do wersji mobilnej oraz prognozy dotyczące wejścia rozwiązania na rynek w najbliższych latach.
-
Gaseous standard mixtures - the challenge of obtaining small amounts of measurands.
PublicationOpisano wykorzystanie techniki termicznego rozkładu związków powierzchniowych do sporządzania gazowych mieszanin wzorcowych. Przedstawiono wyniki własnych badań ukazujących możliwości uzyskiwania szerokiego zakresu ilości składników mierzonych. Opisano także sposoby wykorzystania otrzymanych mieszanin wzorcowych do kalibracji urządzeń kontrolno-pomiarowych.
-
Application of the IMO standard manoeuvres procedure for pod-driven ships
PublicationInternational Maritime Organisation (IMO) in the resolution MSC.137(76) Standards for Ship manoeuvrability presents the manoeuvring criteria that has to be satisfied by majority of seagoing ships. Together with the criteria, procedures for carrying out the manoeuvring tests are also presented. They however do not correspond directly to ships with non-conventional steering-propulsion devices, like pod drives. IMO is aware of this...
-
Gaseous standard mixtures – the challenge of obtaining small amounts of measurands
Publication -
Generation of standard gaseous mixtures by thermal decomposition of surface compounds
Publication -
Digital Imaging and Communication in Medicine Standard for Breast Thermal Imaging
PublicationOmówiono znaczenie normy DICOM w obrazowaniu medycznym. Zaproponowano metodę opisu danych w diagnostyce terminczej piersi dla potrzeb normy DICOM. Zaprojektowano i wykonano algorytmy automatycznej konwersji danych oraz tworzenia struktur danych w hierarchiczno-obiektowym modelu danych.
-
Application of IR UWB Spectrum Shaping to IEEE 802.15.4a Standard
PublicationCoexistence of existing narrowband systems and new ultra wideband devices in the same frequency range requires using some interference mitigation techniques, for example based on spectrum shaping. This paper presents efficiency of impulse radio spectrum shaping methods, applied to IEEE 802.15.4a UWB alternate physical layer signals. Basic parameters of 802.15.4a signal structure and outline of proposed spectrum shaping methods...
-
The data exchange between smart glasses and healthcare information systems using the HL7 FHIR standard
PublicationIn this study we evaluated system architecture for the use of smart glasses as a viewer of information, as a source of medical data (vital sign measurements: temperature, pulse rate, and respiration rate), and as a filter of healthcare information. All activities were based on patient/device identification procedures using graphical markers or features based on visual appearance. The architecture and particular use cases were implemented...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Globalized Knowledge-Based Simulation-Driven Antenna Miniaturization Using Domain-Confined Surrogates and Dimensionality Reduction
PublicationDesign of contemporary antenna systems encounters multifold challenges, one of which is a limited size. Compact antennas are indispensable for the new fields of application such as inter-net of things or 5G/6G mobile communication. Still, miniaturization generally undermines elec-trical and field performance. When attempted through numerical optimization, it turns into a constrained problem with costly constraints requiring electromagnetic...
-
Macro-elements and Model Order Reduction for Efficient Three-Dimensional FEM Analysis
PublicationAn efficient model order reduction (MOR) methodology for three dimensional vector finite element method (FEM) is developed to accelerate simulations of the structures containing features that cause strong variations of mesh density. As the result of presented algorithm, FEM subsystems of equations corresponding to the selected refined region are converted into a very compact sets of linear equations, called macro-elements.Numerical...
-
On EM-driven size reduction of antenna structures with explicit constraint handling
PublicationSimulation-driven miniaturization of antenna components is a challenging task mainly due to the presence of expensive constraints, evaluation of which involves full-wave electromagnetic (EM) analysis. The recommended approach is implicit constraint handling using penalty functions, which, however, requires a meticulous selection of penalty coefficients, instrumental in ensuring optimization process reliability. This paper proposes...
-
The regional energy transformation in the context of renewable energy sources potential
PublicationThe topics addressed in the article concern the problem of exploiting the potential of renewable energy sources (RES) at the regional level and the problem of the course of regional energy transition processes. Throughout the world, energy transition proceeds in a specific way for each country, due to the different potential of the selected RES and political, institutional and socio-economic conditions. Energy transition processes...
-
Development of a compact microstrip resonant cell aimed at efficient microwave component size reduction
PublicationA comprehensive comparison of a wide collection of compact microstrip resonant cells (CMRCs) found in the extensive body of literature has been presented. The evaluation of different CMRC designs has led to the selection of the most promising CMRC geometry for the efficient miniaturisation of modern microwave components. In order to showcase the vital effectiveness of the approach, the initially selected CMRC has been notably...
-
Spurious Modes in Model Order Reduction in Variational Problems in Electromagnetics
PublicationIn this work, we address an everlasting issue in 2 model order reduction (MOR) in electromagnetics that has 3 remained unnoticed until now. Contrary to what has been 4 previously done, we identify for the very first time spurious 5 modes in MOR for time-harmonic Maxwell’s equations and 6 propose a methodology to remove their negative influence on the 7 reduced order model (ROM) response. These spurious modes 8 have nonzero resonance...
-
Quasirelativistic potential energy curves and transition dipole moments of NaRb
PublicationWe report on extensive calculations of quasi-relativistic potential energy curves and, for the first time, transition dipole moments including spin-orbit and scalar-relativistic effects of the NaRb molecule. The calculated curves of the 0+, 0-, 1, 2 and 3 molecular states correlate for large internuclear separation with the fourteen lowest atomic energies up to the Na(3s ^2S_{1/2}) + Rb(7s ^2S_{1/2}) atomic limit. Several new features...
-
Personal Entrepreneurial Potential in the Opinion of Young Women Entering the Labor Market
PublicationIn the current economic situation in Europe the need to stimulate entrepreneurship, with the special attention to develop the entrepreneurship among women, is clearly emphasized. The action is mostly taken to encourage the use of internal potential of possible future entrepreneurs. Do we know what the potential really is ? The presented article deals with the issues of women's entrepreneurship, demonstrating results of self assessment...
-
Potential Energy Curves of Diatomic Alkali Molecules Datasets
PublicationThe datasets described in this article contain potential energy curves for several diatomic systems. The data was obtained via high-performance computing using MOLPRO, a system of ab initio programs for advanced molecular electronic structure calculations. The datasets allow to model bond lengths, energy levels, spectra and time-evolution of molecular dimers for which the data are presented.
-
Structure and thermoelectric properties of Cs-Bi-Te alloys fabricated by different routes of reduction of oxide reagents
PublicationCesium-bismuth-telluride polycrystalline materials were fabricated using a cost-effective method based on a reduction of oxide reagents, leading to a production of a material with good thermoelectric properties. Several samples with various initial stoichiometry were prepared by melting of oxide powders at 1050 °C, quenching, milling to powders and then reducing in pure hydrogen at 400 °C. Another concept was to obtain the CsBi4Te6...
-
Potential energy curves, transition and permanent dipole moments of KRb
PublicationWe present extensive calculations of 48 adiabatic potential energy curves of the KRb molecule. Efforts have been focused on preparing the appropriate basis sets. Compared to previous approaches, the set of new potential energy curves is extended to higher excitations, including the single-excited K(4s2S)+Rb(5d2D) and double-excited K(4p2P)+Rb(5p2P) atomic limits. Larger distances between nuclei are also taken into account. New...
-
SEM images of (La0.3Sr0.6Ce0.1)0.9Me0.1Ti0.9O3-δ (Me=Co, Fe, Ni) powder materials after reduction at 1000 deg.C in hydrogen
Open Research DataThe dataset presents SEM images of (La0.3Sr0.6Ce0.1)0.9Me0.1Ti0.9O3-δ (Me=Co, Fe, Ni) powder materials after reduction at 1000 deg.C in hydrogen. The powders were synthesized via the Pechini method. The reduction was performed in order to force the exsolution process of metallic nanoparticles.
-
Laboratory investigation with subbottom parametric echosounder SES-2000 standard with an emphasis on reflected pure signals analysis
PublicationThe main goal of the paper is to describe correlations between measurements results of trials taken on Gulf of Gdańsk bottom sounded with parametric echosounder SES-2000 Standard and laboratory research where collected during survey sediments were measured. Stationary tests took place at Gdansk University of Technology where 30 meters long 1.8 meter deep and 3 meters wide water tank is located. Main lobe of antenna was directed...
-
Study of the Effectiveness of Model Order Reduction Algorithms in the Finite Element Method Analysis of Multi-port Microwave Structures
PublicationThe purpose of this paper is to investigate the effectiveness of model order reduction algorithms in finite element method analysis of multi-port microwave structures. Consideration is given to state of the art algorithms, i.e. compact reduced-basis method (CRBM), second-order Arnoldi method for passive-order reduction (SAPOR), reduced-basis methods (RBM) and subspace-splitting moment-matching MOR (SSMM-MOR)