Filtry
wszystkich: 3565
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: amikacin sulfate
-
Surface contamination after lapping by abrasive material
PublikacjaPrzedstawiono wyniki badań skażenia powierzchni żeliwa sferoidalnego mikroziarnami węglika krzemu po docieraniu. Określowo wpływ współczynnika upakowania mikroziaren w strefie docierania na intensywność skażenia powierzchni ścierniwem. W badaniach wykorzystano powierzchniową mikroanalizę rentgenowską.
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Surface vaviness of components machined by burnishing method
PublikacjaPowierzchnię po obróbce wykończeniowej definiuje się zazwyczaj za pomocą parametrów chropowatości. Rosnące wymagania jakościowe w stosunku do wytwarzanych części maszyn powodują rozszerzanie się zakresu parametrów opisujących powierzchnię. W artykule przedstawiono ocenę jakościową powierzchni nagniatanych za pomocą parametrów falistości.
-
Surface Dielectric Barrier Discharge Plasma Actuators
PublikacjaThis paper presents a part of the works conducted in the Plasmaero European project (task 1.1) on surface dielectric barrier discharge actuators applied to airflow control. The study is divided into several parts. In the first part, the goal is to enhance the electric wind produced by a typical single DBD actuator by optimization of the active electrode shape. For instance, the use of a thin wire instead of a plate air-exposed...
-
PERS - QUIET ROAD SURFACE FOR URBAN AREAS
PublikacjaTraffic noise is one of the most important environmental problems in densely populated urban areas. At low speeds the tyre/road interaction dominates all other sources. It is anticipated that when electric and hybrid vehicles gain dominance in city traffic, the importance of tyre/road noise will still increase as electric engines are much less noisy than combustion engines. On the other hand, electric and hybrid urban vehicles...
-
Body surface area formulae: an alarming ambiguity
PublikacjaBody surface area (BSA) plays a key role in several medical fields, including cancer chemotherapy, transplantology, burn treatment and toxicology. BSA is often a major factor in the determination of the course of treatment and drug dosage. A series of formulae to simplify the process have been developed. Because easy-to-identify, yet general, body coefficient results of those formulae vary considerably, the question arises as to...
-
The Effect of Dimple Distortions on Surface Topography Analysis
Publikacja -
Reduction of the end-effect in surface texture analysis
Publikacja -
Detection of measurement noise in surface topography analysis
Publikacja -
Problems of surface topography with oil pockets analysis
Publikacja -
Effect of surface modification on starch biopolymer wettability
Publikacja -
Effect of surface modification on starch/phospholipid wettability
Publikacja -
Calcium sulphate scaling in membrane distillation process
Publikacja -
On the Bending of Multilayered Plates Considering Surface Viscoelasticity
PublikacjaWe discuss the bending resistance of multilayered plates taking into account surface/interfacial viscoelasticity. Within the linear surface viscoelasticity we introduce the surface/interfacial stresses linearly dependent on the history of surface strains. In order to underline the surface viscoelasticity contribution to the bending response we restrict ourselves to the elastic behaviour in the bulk. Using the correspondence principle...
-
Singular Surface Curves in the Resultant Thermodynamics of Shells
PublikacjaWithin six-parameter shells theory we discuss the governing equations of shells with material or non-material singular curves. By singular curve we mean a surface curve where are discontinuities in some surface fields. As an example we consider shells with junctions and shells undergoing stress-induced phase transitions.
-
Influence of dissolved organic nitrogen on surface waters
PublikacjaThe aim of this study was to determine the susceptibility of dissolved organic nitrogen (DON) contained in biologically treated wastewater disposed from municipal wastewater treatment plants (WWTPs) to biodegradability and bioavailability in a water environment. Additionally an evaluation was performed of the participation of this organic nitrogen fraction, including bioavailable DON (bDON), in the nitrogen balance for the Baltic...
-
Force-induced structural changes in non-sulfated carrageenan based oligosaccharides – a theoretical study
Publikacja -
Enforced conformational changes in the structural units of glycosaminoglycan (non-sulfated heparin-based oligosaccharides)
Publikacja -
Surface chemistry aspects of fluorosurfactants as components in AFFF preparation
PublikacjaZbadano właściwości powierzchniowe fluorowanych surfaktantów anionowych a także roztworów środków pianotwórczych na bazie fluorowanych surfaktantów stosowanych w gaszeniu pożarów substancji ropopochodnych ze szczególnym uwzględnieniem ich zdolności do obniżania napięć międzyfazowych. Wyselekcjonowana para surfaktantów wykazała się wysoką zdolnością obniżania napięć międzyfazowych na granicy faz olej-woda, porównywalną z roztworami...
-
Sulphate reducing bacteria in groundwater intakes in Gdańsk Region.
PublikacjaPraca przedstawia wyniki badań określające występowanie bakterii redukujących siarczany w wodach podziemnych ujmowanych z utworów kredowych oraz z utworów czwartorzędowych w regionie gdańskim. Bakterie te okresowo znajdują odpowiednie warunki do wzrostu w środowisku wód podziemnych i w wyniku procesów metabolizmu produkują siarkowodór pogarszający cechy organoleptyczne wody. W celu ograniczenia niekorzystnych zmian jakości wody...
-
The surface contact characteristics after sliding and rolling burnishing.
PublikacjaW pracy przedstawiono zastosowanie nowej metody SCGC i odpowiedniego programu komputerowego JKC do oceny pomierzonej mikrostereometrii powierzchni części maszyn, głównie na potrzeby kontroli jakości. Na przykładzie powierzchni nagniatanych wykazano cechy nowej metody: wizualizację ułatwiającą wyobrażenie pomierzonej sfery chropowatości, położenie w niej najważniejszych parametrów oceny (rozkład geometrycznej powierzchni kontaktu,...
-
Fatigue test bearings with geometrically modyfied sliding surface.
PublikacjaW artykule uzasadniono celowość wprowadzenia nowego łóżyska testowego do badań wytrzymałości zmęczeniowej materiałów łożyskowych. Przedstawiono wstępne wyniki badań łożysk o zmodyfikowanej geometrii powierzchni ślizgowej i porównano otrzymane wyniki testów przeprowadzonych przy użyciu o standartowej geometrii.
-
Monitoring surfactant concentrations in surface waters in Tricity agglomeration.
PublikacjaCelem prowadzonych badań było monitorowanie zawartości związków powierzchniowo- czynnych w wybranych rzekach Trójmiasta i Zatoki Gdańskiej. Badania prowadzono w okresie od listopada 2001 do maja 2002 r. W badanych strumieniach wodnych zanotowano niskie stężenia anionowych związków powierzchniowo czynnych (5-10ćg/dm3). Najwyższą zawartość surfaktantów zaobserwowano w potoku Strzyża i rzece Kacza. Najmniej zanieczyszczonym...
-
Some aspects of laser surface remelting of aluminium alloys
PublikacjaPodano podstawy procesu przetapiania laserowego stopów aluminium. Opisano rezultaty elektrochemicznych badań korozyjnych dla stopu AlSi13Mg1CuNi i porównano je ze stanem wyjściowym stopu.
-
Surface layer defects on injection-molded plastic components
PublikacjaProces wtryskiwania jakkolwiek jest powszechnie stosowany w przemyśle nie jest jeszcze do końca przebadany. W pracy przedstawiono model i symulację numeryczna procesu wtryskiwania wykonaną na bazie programu FIDAP. Na tej podstawie przedstawiono proces zachowania się tworzywa podczas procesu wtryskiwania w strefie przyściennej formy. Wyniki z symulacji porównano z danymi ekspermentalnymi.
-
Laser surface treatment of aluminium alloys at cryogenic conditions.
PublikacjaPrzedstawiono nową metodę obróbki laserowej powierzchni stopów aluminium w warunkach kriogenicznych. W wyniku tej obróbki w warstwie wierzchniej stopów przeznaczonych na tłoki silników spalinowych uzyskano znaczące podwyższenie twardości, odporności na zużycie ścierne oraz wzrost właściwości korozyjnych.
-
A surface panel method for hydrodynamic analysis of pod propulsors
PublikacjaPraca przedstawia zastosowanie metody elementów brzegowych do analizy hydrodynamicznych pędników azymutalnych, czyli do wyznaczania rozkładu ciśnienia i wielkości sił hydrodynamicznych dla pędnika o znanej geometrii i o znanych parametrach pracy.
-
Distribution of roughness and waviness components of turned surface profiles
PublikacjaThe paper presents a spectral formulation of surface profile irregularity in a wideband frequency range for roughness, waviness and shape components along the measured length. A unique distribution of roughness and waviness components is proposed, according to the nature of their origination in the course of machining with tools of defined cutting edge, as distinct from standard filtration in measurements of surface irregularities....
-
Post-plasma oxidation in water of graphene paper surface
Publikacja -
An effective Hamiltonian for sulfur adsorption at Au(100) surface
Publikacja -
Distribution and bioavailability of mercury in the surface sediments of the Baltic Sea
PublikacjaThe study aimed to determine the level of mercury (Hg) and its labile and stable forms in the surface sediments of the Baltic Sea. The work considers the impact of current and historical sources of Hg on sediment pollution, together with the influence of different environmental parameters, including water inflows from the North Sea. Surface sediments (top 5 cm) were collected in 2016–2017 at 91 stations located in different...
-
Entropy analysis of surface EMG for classification of face movements
Publikacja -
On Nonlinear Dynamic Theory of Thin Plates with Surface Stresses
PublikacjaWe discuss the modelling of dynamics of thin plates considering surface stresses according to Gurtin–Murdoch surface elasticity. Taking into account the surface mass density we derive the two-dimensional (2D) equations of motion. For the reduction of the three-dimensional (3D) motion equations to the 2D ones we use the trough-the-thickness integration procedure. As a result, the 2D dynamic parameters of the plate depend not only...
-
Types of Surface Impurities versus the Quality of Brazed Joints
PublikacjaBrazing is one of the primary joining processes increasingly often applied in industry. Because of their mechanical properties, overlap joints are particularly popular when making brazed structures. The use of brazed joints in structures of critical importance requires that particular attention be paid to joint quality, e.g. by the appropriate cleaning of surfaces to be joined. The article presents results of non-destructive tests...
-
Au-RE-TiO2 nanocomposites: Surface characteristics and photoactivity
PublikacjaThe photocatalysts based on TiO2 co-doped with rare earth metal (RE) and gold nanoparticles have been prepared using a sol-gel method and followed by gold reduction. Specific surface areas of the modified photocatalysts were calculated by the Brunauer-Emmett-Teller method (BET). Diffuse reflectance spectra of the obtained photocatalysts were recorded in a UV-Vis spectrophotometer (DRS UV-Vis). The influence of the type of rare...
-
Tyre/road noise reduction by a poroelastic road surface
PublikacjaLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
The concept of anti-collision system of autonomous surface vehicle
PublikacjaThe use of unmanned vehicles in various fields of science and the economy is becoming more common. An extremely important aspect of creating this type of solution is to provide autonomous vehicle navigation, which does not require interference of the human factor or in which it is limited to a minimum. This article discusses the concept of autonomous anti-collision system of unmanned surface vehicle. It proposed a sensor system...
-
Surface Roughness Model Components Created by Stereolithography Method
PublikacjaW pracy przedstawiono charakterystykę powierzchni elementów wykonywanych metodą stereolitografii. Opisano modele chropowatosci stosowane do opisywania powierzcni wraz z prezentacją formuł matematycznych. W oparciu o wyniki badań eksperymentalnych przeprowadzono częściową weryfikację modeli.
-
Profile and Areal Surface Parameters for Fatigue Fracture Characterisation
Publikacja -
Unusual interfacial phenomena at a surface of fullerite and carbon nanotubes
Publikacja -
The corrosion resistance of laser surface alloyed stainless steels
Publikacja -
How important are scaffolds and their surface properties in regenerative medicine
Publikacja -
Surface treatment of porous Ti13Nb13Zr alloy for biomedical applications
PublikacjaPrzeprowadzono badania materiału porowatego, przeznaczonego na implanty ortopedyczne, wytworzonego metodą metalurgii proszków ze stopu Ti13Nb13Zr. Proszki z badanego stopu uzyskano metodą rozpylania plazmowego. Otrzymano próbki o otwartej porowatej strukturze, stopniu porowatości do 68% i średniej wielkości porów w przedziale 30-150 mikrometrów. Obróbka próbek porowatych - utlenianie termiczne, chemiczne i/lub elektrochemiczne...
-
Antagonist adhesion effects due to variable substrate surface
PublikacjaThe effects of variability of intrinsic adhesion within a joint have been studied using a single cantilever beam (SCB) test. Fracture energy was found not to be a simple function of relative areas of 2 surface pre-treatments: a 'weak' zone decreased strength more than expected from simple, additive considerations. By severing the adhesive along the strong-weak transition, fracture energy increased.The prior antagonist effect appears...
-
New laser-enhanced surface treatment of Ti bioalloy
PublikacjaPrzedstawiono wyniki badan mikrostruktury i korozji w roztworze Ringera stopu Ti6Al4V, który był poddawany nadtapianiu laserem CO2 w powietrzu, wodzie i ciekłym azocie. Stwierdzono znaczący wpływ warunków obróbki na mikrostrukturę, mikrotwardość i głębokość zmodyfikowanej warstwy wierzchniej.
-
Phosphate and Thiophosphate Biphenyl Analogs as Steroid Sulfatase Inhibitors
PublikacjaIn the present work, we report convenient methods for the synthesis and biological evaluation of phosphate and thiophosphate biphenyl derivatives exhibiting steroid sulfatase (STS) activity. The described synthesis is based on straightforward preparation of biphenyl-4-ol and 40-hydroxybiphenyl- 4-carboxylic acid ethyl ester modified with various phosphate or thiophosphate moieties. The inhibitory effects of these compounds were...
-
Synthesis of bicoumarin thiophosphate derivatives as steroid sulfatase inhibitors
PublikacjaBased on the frameworks of 7-hydroxy-2,3-dihydro-1H-cyclopenta[c]chromen-4-one, 3-hydroxy- 7,8,9,10-tetrahydro-6H-benzo[c]chromen-6-one and 3-hydroxy-8,9,10,11-tetrahydro-7H-cyclohepta[c] chromen-6-one, a series of bicoumarin thiophosphate analogs have been synthesized and biologically evaluated. Additionally, their binding modes have been modeled using docking techniques. The inhibitory properties of the synthesized compounds...
-
Surface roughness chracteristic if components created by stereolithography method
PublikacjaModele wykonywane metodami szybkiego prototypowania mają charakterystyczna strukturę powierzchni określaną mianem schodkowatości. W artykule przedstawiono modele obliczeniowe profilu nierówności jak i porównanie ich z wynikami pomiarów
-
Estimation of wear of electroplated tools used for surface grinding
PublikacjaW pracy dokonano ilościowej oceny zużycia narzędzi galwanicznych diamentowych i borazonowych. Wykorzystano analizę jasności obrazów narzędzi oraz badano liczność ziaren ściernych na czynnej powierzchni narzędzia.
-
Computer Supported Analysis of the Human Body Surface Area
PublikacjaRecent scientific studies show the growing importance of the coefficients: BSA and TBSA, as an alternative to the widely used BMI. The relevant indicators are widely used in medicine, including such areas as: the treatment of burns, chemotherapy, dermatology and toxicology; as benchmarks when calculating doses of drugs and fluids. The particular problems concerning this subject are: the change of the reference parameter value which...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublikacjaThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
The influence of road surface unevenness on tyre rolling resistance
PublikacjaThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
Chemical denudation and the role of sulfide oxidation at Werenskioldbreen, Svalbard
PublikacjaThis study aims to determine the rate of chemical denudation and the relationships between dominant geochemical reactions operating in the proglacial and subglacial environments of the polythermal glacier Werenskioldbreen (SW Svalbard) during an entire ablation season. Water sampling for major ion chemistry was performed at a proglacial hydrometric station and from subglacial outflows from May to September 2011. These data were...
-
Basic Hand Gestures Classification Based on Surface Electromyography
PublikacjaThis paper presents an innovative classification system for hand gestures using 2-channel surface electromyography analysis. The system developed uses the Support Vector Machine classifier, for which the kernel function and parameter optimisation are conducted additionally by the Cuckoo Search swarm algorithm. The system developed is compared with standard Support Vector Machine classifiers with various kernel functions. The average...
-
Design of Ground Surface Sealing in The Spatial Policy of Communes
Publikacja -
The Effect of Spikes Occurrence on Surface Texture Parameter Assessments
Publikacja -
EFFECT OF THE BIO-LUBRICANT ON THE LUBRICATINGPROPERTIES AND SURFACE OF THE FRICTION ZONE
Publikacja -
3D Metamaterial Ultra-Wideband Absorber for curved surface
PublikacjaThis paper proposes a three-dimensional metamaterial absorber based on a resistive film patch array to develop a low-cost, lightweight absorber for curved surfaces. An excellent absorption over a large frequency band is achieved through two different yet controllable mechanisms; In the first mechanism, a considerable attenuation in the wave power is achieved via graphite resistive films. The absorption is then intensified through...
-
Detection of Water on Road Surface with Acoustic Vector Sensor
PublikacjaThis paper presents a new approach to detecting the presence of water on a road surface, employing an acoustic vector sensor. The proposed method is based on sound intensity analysis in the frequency domain. Acoustic events, representing road vehicles, are detected in the sound intensity signals. The direction of the incoming sound is calculated for the individual spectral components of the intensity signal, and the components...
-
Surface diffusion and cluster formation of gold on the silicon (111)
PublikacjaPurpose: Investigation of the gold atoms behaviour on the surface of silicon by molecular dynamics simulation method. The studies were performed for the case of one, two and four atoms, as well as incomplete and complete filling of gold atoms on the silicon surface. Design/methodology/approach: Investigations were performed by the method of molecular dynamics simulation using the Large-scale Atomic/Molecular Massively Parallel...
-
A device for measuring heat flux on a rocket skin surface
PublikacjaA novel method for measuring heat flux on a surface is presented. It is an extensive upgrade of currently known heat flux sensors used mostly in civil engineering. As the thermal environment of launchers, especially sounding rocket can have an enormous negative effect on payload, careful considerations have to be taken in the process of preparing insulation. Usually, thermal data provided by the launch vehicle manufacturer is limited...
-
Measurement of temperature at sliding polymer surface by grindable thermocouples
PublikacjaThis paper is devoted to experimental study of capabilities and limitations of grindable thermocouples as applied to polymer materials sliding on metal. Chromel–alumel and chromel–copel grindable thermocouples have been developed and tested for wide ranges of contact pressure and sliding velocity. The background temperature of the sliding surface can be determined as the lower envelope of the signal from the grindable thermocouple....
-
Surface Texture after Turning for Various Workpiece Rigidities
PublikacjaIn the paper, we present an analysis of the surface texture of turned parts with L/D (length/diameter) ratios of 6 and 12 and various rigidity values. The studies were carried out on samples made of S355JR steel and AISI 304 stainless steel. A detailed analysis of 2D surface profiles was carried out by using a large number of parameters that allowed us to distinguish significant differences in the surface microgeometry, which confirmed...
-
The Influence of Laser Alloying of Ti13Nb13Zr on Surface Topography and Properties
PublikacjaThe laser alloying is a continually developing surface treatment because of its significant and specific structuration of a surface. In particular, it is applied for Ti alloys, being now the most essential biomaterials` group for load-bearing implants. The present research was performed on the Ti13Nb13Zr alloy subject to laser modification in order to determine the treatment effects on surface topography and its some mechanical...
-
Wave transmission across surface interfaces in lattice structures
PublikacjaWithin the lattice dynamics formulation, we present an exact solution for anti-plane surface waves in a square lattice strip with a surface row of material particles of two types separated by a linear interface. The considered problem is a discrete analog of an elastic half-space with surface stresses modelled through the simplified Gurtin–Murdoch model, where we have an interfacial line separating areas with different surface...
-
Marine autonomous surface ship - control system configuration
PublikacjaThis paper addresses the problem of marine autonomous surface ship (MASS) control. The contribution of the paper is the development of a control system configuration, done assuming fully autonomous MASS operation under distinct operational conditions. The overview of hardware and software selection is included.
-
On stress singularity near the tip of a crack with surface stresses
PublikacjaIn the framework of the simplified linear Gurtin–Murdoch surface elasticity we discuss a singularity of stresses and displacements in the vicinity of a mode III crack. We show that inhomogeneity in surface elastic properties may significantly affect the solution and to change the order of singularity. We also demonstrate that implicitly or explicitly assumed symmetry of the problem may also lead to changes in solutions. Considering...
-
Treated wasetewater as a source of humic substances in surface waters
PublikacjaHumic substances impose substantial effect on the aquatic environment as well as the water organisms and human health. Among other features, the humic acids determine organoleptic properties of surface waters. Therefore explanation of the origin and properties of humic acids in surface waters is one of the priorities of water technology.Recently it was pointed out that in the wastewater treatment process organic compounds characterized...
-
Free-surface elevation in open vortex flow controls
PublikacjaRotational form of fluid motion is complex, but very important in science and technology. The paper is devoted to the hydraulic mechanism of flow in open vortex flow controls, or regulators. The velocity field was described by the kinematic model, and intensity of rotation - by means of the energy balance between the input and dissipation. In consequence some algebraic expresions were obtained, which can be useful in approximated...
-
Cell Surface
Czasopisma -
Pilot scale degradation study of 16 selected volatile organic compounds by hydroxyl and sulfate radical based advanced oxidation processes
PublikacjaThe studies of effective technologies for complete degradation of the volatile organic compounds (VOCs), are very important due to the high biotoxicity of the VOCs which makes the biological technologies ineffective. It also increases the risk of VOCs emission instead of their treatment when using open air biological technologies. In the present study, different types of Advanced Oxidation Processes (AOPs) were investigated for...
-
Ion Capacity of Siliceous Sorbents with Surface Polymer Layers Composed of Different Dextran—Triethylenetetraamine Mixtures (Ion Capacity of Sorbents with Surface Polymer Layers)
Publikacja -
Effects of Surface Energy and Surface Residual Stresses on Vibro-Thermal Analysis of Chiral, Zigzag, and Armchair Types of SWCNTs Using Refined Beam Theory
PublikacjaIn this article, vibration characteristics of three different types of Single-Walled Carbon Nanotubes (SWCNTs) such as armchair, chiral, and zigzag carbon nanotubes have been investigated considering the effects of surface energy and surface residual stresses. The nanotubes are embedded in the elastic substrate of the Winkler type and are also exposed to low and high-temperature environments. A new refined beam theory namely, one-variable...
-
SURFACE COATINGS INTERNATIONAL PART B-COATINGS TRANSACTIONS
Czasopisma -
International Journal of Surface Engineering and Interdisciplinary Materials Science
Czasopisma -
Periodic and impulsive lubrication of hip joint with stochastic rough surface.
PublikacjaNiniejsza praca przedstawia porównanie wartości nośności uzyskanych numerycznie dla niestacjonarnego smarowania impulsywnego oraz niestacjonarnego smarowania periodycznego sferycznego stawu biodrowego człowieka. W obu przypadkach przyjęto, że smarująca ciecz synowialna ma własności lepkosprężyste a występy chropowatych powierzchni chrząstki stawowej zmieniają się losowo. Charakterystyki zmiennych w czasie rozkładów wartości ciśnienia...
-
Protection of surface water against contamination by wetland systems in Poland
PublikacjaOpisano systemy hydrofitowe stosowane do usuwania zanieczyszczeń z wód powierzchniowych zasilanych wodami opadowymi. Po wprowadzeniu systemów stwierdzono znaczną poprawę jakości wód analizowanych cieków.
-
Laser surface treatment of aluminium-silicon alloy at cryogenic conditions
PublikacjaW artykule przedstawiono wpływ laserowego, powierzchniowego przetapiania w warunkach kriogenicznych na mikrostrukturę, mikrotwardość, zużycie na skutek tarcia oraz korozję stopu aluminium AlSi13Mg1CuNi. Stwierdzono zwiększenie mikrotwardości, odporności na ścieranie i korozję odlewniczego stopu AlSi13Mg1CuNi stosowanego w produkcji tłoków silników spalinowych.
-
Manganese-nitrogen-sulphur surface layers produced on aluminium alloys
PublikacjaPodano metodę wytwarzania warstw powierzchniowych zawierających mangan, azot i siarkę na odlewniczym stopie aluminium. Przedstawiono mikrostrukturę przekroju i powierzchni wytworzonych warstw, ich twardość oraz wlaściwości tribologiczne i korozyjne.
-
Manganese Phosphatizing Coatings: The Effects of Preparation Conditions on Surface Properties
PublikacjaManganese phosphate coating could be used to protect the surface of steel products. However, it is essential to determine the effects which process parameters, as well as the types of additives used, have on the efficiency of coating deposition. Thus, we present here a process of phosphatization of low-alloy steel (for 15 min at 95 ◦C) in manganese/nickel baths followed by a passivation process with the use of a silicon and zircon...
-
The Impact of Drying Conditions on the Surface Color Changes of Pine Wood
PublikacjaThe article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine...
-
Surface quality of the plasma cermet coatings after grind finishing
Publikacja -
Experimental and theoretical study of surface cooling using a single microjet
PublikacjaPrzedstawiono wyniki badań eksperymentalnych intensyfikacji wymiany ciepła przy pomocy pojedynczych strug wody i powietrza.Uzyskana na podstawie wyników korelacja, opisująca współczynnik przejmowania ciepła, posłużyła do weryfikacji modelu opracowanego wcześniej przez Mikielewicza (2007).
-
Low-temperature reactivity of the surface species of vanadia–tungsta catalyst
Publikacja -
Thermal decomposition of surface compounds for the generation of small quantities of acetaldehyde
Publikacja -
Generation of standard gaseous mixtures by thermal decomposition of surface compounds
Publikacja -
On the Equations of the Surface Elasticity Model Based on the Theory of Polymeric Brushes
PublikacjaMotivating by theory of polymers, in particular, by the models of polymeric brushes we present here the homogenized (continual) two-dimensional (2D) model of surface elasticity. A polymeric brush consists of an system of almost aligned rigid polymeric chains. The interaction between chain links are described through Stockmayer potential, which take into account also dipole-dipole interactions. The presented 2D model can be treated...
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Processing of Hydroacoustic and LiDAR Data for Three-dimensional Surface Reconstruction
PublikacjaThe technologies of sonar and laser scanning are commonly used for obtaining spatial information about underwater and over ground environments in the form of point clouds. Since this data model has known disadvantages, a more practical solution of visualising such data involves the creation of solid three-dimensional meshes composed of edges and facets. In this paper, several methods for 3D shape reconstruction of data obtained...
-
Influence and development of new kinematic systems in flat surface lapping
PublikacjaThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...
-
Experimental bases for the rail track surface damage detection system
PublikacjaA diagnosis of rail surface is generally based on the classical method of direct assessment and track geometry measurements. Identification and qualification of inequality and damage on the surface rails is depend on the skills and experience person who conducting inspection. In times of increasing exploitation of railways, infrastructure managers decide to use systems supporting the assessment of technical condition of the railways....
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublikacjaThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublikacjaBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Model Order Reduction for Problems With Dispersive Surface Boundary Conditions
PublikacjaThis letter proposes a new scheme for reduced-order finite-element modeling of electromagnetic structures with nonlinear, dispersive surface boundary conditions, which optimally exploits the numerically stable and efficient MOR framework for second-order systems provided by SAPOR method. The presented results of numerical experiments for an example of a waveguide filter demonstrate the superior accuracy of the resulting reduced models...
-
Surface treatment of C80U steel by long CO2 laser pulses
PublikacjaThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Selected aspects of the surface quality of the wooden elements after planing
PublikacjaThe quality of the surface of wooden elements, that have been planed, has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of wooden surface after painting. The emergence of defects in most cases causes need to qualify workpiece as a scrap part or additional work activity must be done. In the paper selected results of the investigation of the effect of the cutting tool wear...
-
Sulphate-reducing bacteria, their properties and methods of elimination from groundwater
PublikacjaRutynowa kontrola jakości bakteriologicznej wód podziemnych przeznaczonych do spożycia nie obejmuje badania pod względem obecności bakterii charakterystycznych dla tego środowiska tj. bakterii redukujących siarczany (BRS), które mogą mieć negatywny wpływ na jakość wody. Stwierdzono obecność tych bakterii w wodach podziemnych rejonu Gdańska. Wyizolowano konsorcja BRS, które wykazywały preferencję do wykorzystywania mleczanu sodu...
-
Surface-Plasmon-Coupled Emission of Rhodamine 110 in a Silica Nanolayer
PublikacjaThe first observation of strong directional surface-plasmon-coupled emission (SPCE) of Rhodamine 110 in silica nanofilms deposited on silver nanolayers is reported. The preparation of the material is described in detail. The intensity of SPCE exceeds 10 times that of free space fluorescence and total linear light polarization in the SPCE ring is observed. A new experimental setup and an original data collection method is presented....
-
Blur recognition using second fundamental form of image surface
Publikacja -
Aluminium surface treatment with ceramic phases using diode laser
Publikacja