Filters
total: 1452
filtered: 1244
displaying 1000 best results Help
Search results for: CAST-IN-PLACE CONCRETE
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublicationT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Assessing ecotoxicity, synergic and antagonistic actions of commonly used components of polymerization mixture in molecularly imprinted polymers preparation process
PublicationIncreasingly, the challenge is the optimal process of developing a suitable MIP-type sorptive material (taking into account its final form and application area), which is mainly related to the efficiency/effectiveness of the polymerization process. The lack of reaction or its low efficiency generates additional waste and puts it into the environmental cycle. The main aim of the performed research was the estimation of ecotoxicity,...
-
Value co‐creation (VCC) and value co‐destruction (VCD) via open government data (OGD): Empirical case of Tanzania
PublicationHaving emphasized upon the potential benefits of Open Government Data (OGD) initiatives via value derivation and innovation pursuits of the stakeholders, it falls in place to complement this line of OGD research in the specific case of Tanzania, a developing country, to support the inferences. Specifically, it is important to understand the manner in which OGD VCC-one of the hinges of OGD initiatives- and OGD VCD-a possible fall...
-
Simulation of fluid structure interaction in a novel design of high pressure axial piston hydraulic pump
PublicationA novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology,...
-
When all we have is not enough: a search for the optimal method of quantifying inflation expectations
PublicationAlthough inflation expectations are pivotal variables for central banks, they are not directly observable. Therefore, central banks use qualitative survey results to proxy consumer expectations, and their quantification in this manner is often criticized. In this study, we investigate and identify an optimal quantification procedure for survey results based on a set of regression and probabilistic models. Specifically, we seek...
-
Designing with Green and Blue – Climate Adaption Proposals for Lowland Areas of Gdańsk
PublicationThe paper gives insight into issues explored within the framework of the SOS Climate Waterfront workshop that took place in Gdańsk in June 2019. The aim of the study was to propose solutions that will decrease the number of flooding events and span the gap between flood prevention strategies and the provision of other benefits such as ecological, urban, cultural and social. Historical cartography enquiries and research by the design...
-
The process of identification of the track's geometrical layout and the alignment project based on the of satellite measurements
PublicationIn the paper a methodology of restoring of railway track’s geometrical shape in a horizontal plane on the base of conducted mobile satellite surveying was presented. The authors proposed a calculating algorithm for designing the track sections placed in horizontal arcs. In the algorithm an analytical methodology with mathematical formulas is applied. The procedure has an universal character, i.e. provides the possibility of varying...
-
Satellite inventory of tram track geometrical layout
PublicationIn the paper a methodology of restoring of railway track’s geometrical shape in a horizontal plane on the base of conducted mobile satellite surveying was presented. The authors proposed a calculating algorithm for designing the track sections placed in horizontal arcs. In the algorithm an analytical methodology with mathematical formulas is applied. The procedure has an universal character, i.e. provides the possibility of varying...
-
Analytical tools for functional assessment of architectural layouts
PublicationFunctional layout of the building, understood as a layout or set of the facility rooms (or groups of rooms) with a system of internal communication, creates an environment and a place of mutual relations between the occupants of the object. Achieving optimal (from the occupants’ point of view) spatial arrangement is possible through activities that often go beyond the stage of architectural design. Adopted in the architectural...
-
Metal dusting phenomena of 501 AISI furnace tubes in refinery fractional distillation unit
PublicationThe purpose of this investigation was to conduct the failure analysis of 501 AISI furnace tubes places before distillation column in fractional distillation unit. The investigated furnace tubes were planned to work for ten years however after just two years of exploitation <30% of the material left. The observed corrosion process had the intense and complex character. The well-adhered shiny black deposits and deep, round pits were...
-
Annual variability of heavy metal content in Svalbard reindeer faeces as a result of dietary preferences
PublicationDuring both winter and summer, Svalbard reindeer selectively feed on different types of vegetation that are not only a source of nutritional value, but also a place of heavy metal accumulation. In the present study, the content of cadmium, chromium, copper, iron, lead, nickel, manganese, and zinc in reindeer excrement was measured. The main aims were to determine the seasonal content of several heavy metals in Svalbard reindeer...
-
A method of Functional Test interval selection with regards to Machinery and Economical aspects
PublicationThis paper discusses the problem of choosing the optimal frequency of functional test, including the reliability calculations and production efficiency, but also the effect of company risk management. The proof test as a part of the functional test interval is well described for the process industry. Unfortunately, this situation is not the case for the machinery safety functions with low demand mode. Afterwards, it is presented...
-
Computed aided system for separation and classification of the abnormal erythrocytes in human blood
PublicationThe human peripheral blood consists of cells (red cells, white cells, and platelets) suspended in plasma. In the following research the team assessed an influence of nanodiamond particles on blood elements over various periods of time. The material used in the study consisted of samples taken from ten healthy humans of various age, different blood types and both sexes. The markings were leaded by adding to the blood unmodified...
-
Design of reverse curves adapted to the satellite measurements
PublicationThe paper presents a new method for designing railway route in the direction change area adapted to the Mobile Satellite Measurements technique. The method may be particularly useful in the situations when both tangents cannot be connected in an elementary way using a circular arc with transition curves. Thus, the only solution would be the application of two circular arcs of opposite curvature signs, that is, the use of an inverse...
-
Controlled grafting of vinylic monomers on polyolefins: a robust mathematical modeling approach
PublicationExperimental and mathematical modeling analyses were used for controlling melt free-radical grafting of vinylic monomers on polyolefins and, thereby, reducing the disturbance of undesired cross-linking of polyolefins. Response surface, desirability function, and artificial intelligence methodologies were blended to modeling/optimization of grafting reaction in terms of vinylic monomer content, peroxide initiator concentration,...
-
Electrochemical performance of Co3O4/CeO2 electrodes in H2S/H2O atmospheres in a proton-conducting ceramic symmetrical cell with BaZr0.7Ce0.2Y0.1O3 solid electrolyte
PublicationThe electrochemical performance of Co3O4/CeO2 mixed oxide materials as electrodes, when exposed to H2S/H2O atmospheres, was examined employing a proton conducting symmetrical cell, with BaZr0.7Ce0.2Y0.1O3 (BZCY72) as the solid electrolyte. The impact of temperature (700–850 °C) and H2S concentration (0–1 v/v%) in steam-rich atmospheres (90 v/v% H2O) on the overall cell performance was thoroughly assessed by means of electrochemical...
-
Machine learning approach to packaging compatibility testing in the new product development process
PublicationThe paper compares the effectiveness of selected machine learning methods as modelling tools supporting the selection of a packaging type in new product development process. The main goal of the developed model is to reduce the risk of failure in compatibility tests which are preformed to ensure safety, durability, and efficacy of the finished product for the entire period of its shelf life and consumer use. This kind of testing...
-
Diagnostyka ultradźwiękowa mostowej belki prefabrykowanej typu T metodą młoteczkową
PublicationZastosowanie prefabrykacji w budowie obiektów mostowych pozwala optymalizować zużycie energii i materiałów i tym samym redukować koszty budowanego obiektu. Prefabrykowane belki sprężone mogą występować jako elementy kablobetonowe wykonywane bezpośrednio na placu budowy lub powstawać w zakładzie prefabrykacji jako elementy strunobetonowe. Elementy prefabrykowane wytwarzane w warunkach przemysłowych muszą spełniać wymagania wysokiej trwałości,...
-
Instalacja oświetleniowa w zbiorniku wody "Stary Sobieski" - rozważania o spektakularnym zabytku techniki
PublicationArtykuł przedstawia efekty badań autora nad niezwykle okazałą, ponad stuletnią instalacją elektryczną, która zachowała się w zabytkowym obiekcie infrastruktury wodociągowej w niemal 100% oryginalnej formie (nie licząc częściowej dewastacji). Jest to rzadki przykład tego rodzaju zabytku, ponieważ obiekty tego typu i w tym wieku zwykle podlegały modernizacji na przestrzeni lat albo, po wyłączeniu z eksploatacji zostały całkowicie...
-
Ocena wpływu dodatku oliwy z oliwek na degradację termiczną rafinowanego oleju rzepakowego
PublicationTłuszcze jadalne to ważny składnik diety człowieka. Mają one znaczący wpływ na prawidłowe funkcjonowanie ludzkiego organizmu. Podczas smażenia olej podlega przemianom chemicznym, dlatego spożywane tłuszcze powinny charakteryzować się jak największą stabilności oksydacyjnej. Celem prowadzonych badań było określenie jakości olejów rzepakowego, mieszanego oraz rafinowanej oliwy z oliwek, pochodzących z rynku krajowego. Podczas badań...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Challenges and opportunities related to the use of sewage sludge ash in cement-based building materials – A review
PublicationDue to the increasingly demanding legal regulations, regarding both sewage sludge (SS) and solid residues obtained during its thermal utilization processes, new solutions to limit their negative impact on the environment are sought. One approach that eliminates the risk of sewage sludge ash (SSA) is its use in cement building materials. The article contains a detailed literature review regarding the use of SSA in mortars and concretes,...
-
Building damage due to structural pounding during earthquakes
PublicationEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
DYNAMIC ANALYSIS OF THE RAILWAY BRIDGES IN POLAND WITH REGARDS TO HIGH-SPEED TRAINS PASSAGE ADJUSTMENT
PublicationThe dynamic analysis of the railway bridge in Tczew was carried out in the article as an example of such bridges adaptation suitability to handle high-speed trains. Calculations of railway bridges are greatly complicated and labor-consuming. The bridge model and a rolling stock passage simulation were developed in the SOFISTIK software. Three types of elements were used for the correct mapping of the structure in the calculation...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublicationThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
The long-term properties of mineral-cement-emulsion mixtures
PublicationThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Sustainable utilization of copper post-flotation waste in cement composites
PublicationThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublicationThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
The influence oil additives on spread cracks in silicon nitride
PublicationThe paper presents an experimental study of the influence of oil additives (Cl, S, P, cerium dioxide (CeO2)) on spread cracks in silicon nitride. The additives Cl, S, P are bound in molecules in liquid form soluble in the base oil. The CeO2 is purely in powder form in suspension. The use of CeO2 powder was made based on the good results of polishing of silicon nitride. A ceramic angular contact ball bearing was modelled using a...
-
New Procedures for Control of Industrial Effluents Treatment Processes
PublicationThis work presents the procedures for monitoring volatile organic compounds during treatment of industrial effluents. The investigation was carried out for a specific effluent—caustic effluent from bitumen production. The developed procedures enable more detailed control of the effectiveness of wastewater treatment than standard procedures. Caustic effluents from bitumen production have a complex physicochemical form and consist...
-
Fertility rebound and economic growth. New evidence for 18 countries over the period 1970-2011.
PublicationLong-run impact of economic growth on fertility trends is ambiguous and sensitive for in-time variations. Noticeably, over last decades, economic growth has led in many countries to significant falls in total fertility rates. However, recently, in high-income economies a kind of ‘fertility rebound’ emerged (Goldstein, 2009; Luci and Thevenon, 2011; Day, 2012), which supports the hypothesis that reversal trends in total fertility...
-
Nitric Oxide-Dependent Pathways as Critical Factors in the Consequences and Recovery after Brain Ischemic Hypoxia
PublicationBrain ischemia is one of the leading causes of disability and mortality worldwide. Nitric oxide (NO), a molecule that is involved in the regulation of proper blood flow, vasodilation, neuronal and glial activity constitutes the crucial factor that contributes to the development of pathological changes after stroke. One of the early consequences of a sudden interruption in the cerebral blood flow is the massive production of reactive...
-
Effects of the Covid-19 travel restrictions on metropolises mobility: empirical evidence from the Tricity metropolis (Poland)
PublicationThis paper aims to assess changes in mobility and modal shift caused by COVID-19 travel restrictions among the residents of Gdańsk Bay Metropolis (Poland). Measurement’s moments were assumed in periods differing in the level of restric- tions. The computer-assisted telephone interview (CATI) was carried out in November and December 2020. The results did not confirm the expected modal shift. However, significant changes in the number...
-
How pesticides affect neonates? - Exposure, health implications and determination of metabolites
PublicationThis review covers key information related to the effects of pesticides on fetal and child health. All humans are exposed to environmental toxicants, however child's health, due to their high vulnerability, should be of special concern. They are continuously exposed to environmental xenobiotics including a wide variety of pesticides, and other pollutants. These compounds can enter the child's body through various routes, both during...
-
Where the Second World War in Europe broke out: the land-scape history of Westerplatte, Gdańsk/Danzig
PublicationWesterplatte is known as the place where the Second World War in Europe broke out. However, its history covers many other events involving Polish, German, Russian and even French politics over the last three centuries - neglected by many papers published in the current discussion. Due to its location at the entrance to the main harbour on the Baltic Sea entrance, Wester-platte-Peninsula is cartographically the best-documented part...
-
Powojenny rozdział w historii architektury i zagospodarowania portu gdyńskiego
PublicationThe port of Gdynia, considered one of the largest civil construction projects of the 20th century in Europe, was built at an express pace for only a dozen or so years from the mid-1920s to the end of the 1930s. Unusual solutions from the construction period in the port engineering category, as well as outstanding architectural works The industrial area quickly became architectural symbols of economic growth and the general rebirth...
-
Atmospheric degradation mechanism of anthracene initiated by OH•: A DFT prediction
PublicationDensity functional theory (DFT) calculations at the M06-2X/def2-TZVP level have been employed to investigate the atmospheric oxidation mechanism of anthracene (ANT) initiated by HO•. Direct hydrogen atom abstraction from the ANT using HO• takes place hardly at ambient conditions while the addition of HO• to the C1, C2, and C4 sites are thermodynamically and kinetically more advantageous. The addition reactions are controlled by...
-
Towards Carbon Neutral Settlements. The Importance of Early-Stage Urban and Energetic Optimizations
PublicationThe aim of the research was to verify the essence of interdisciplinary energy optimizations in earlystage urban design process. A further aim was to the find most optimal design variant and scenario in terms of urban energy efficiency for the future development in Nowy Port, located in Gdansk, Poland - a place requiring complex revitalization. The research combined qualitative and quantitative approaches; an urban design layer...
-
Health Enhancing Physical Activity Policies in Poland: Findings from the HEPA PAT Survey
PublicationInsufficient physical activity (PA) is one of major risk factors for serious diseases and premature mortality worldwide. Public policies to enhance PA across society are recognized as an effective tool against the problem. This paper presents the results of a comprehensive assessment of national-level PA policy approach in Poland. A standardized survey of Word Health Organization named the Health-Enhancing Physical Activity Policy...
-
Torque capacity of multidisc wet clutch with reference to friction occurrence on its spline connections
PublicationIn this article developed mathematical model that includes friction occurrence on spline connections is presented. The work also contains results of experimental research on torque capacity of multidisc wet clutch. These results are expressed as a function of contact pressure for different number of friction surfaces. Due to increased interest in research concerning multidisc wet clutches it is essential to determine impact of...
-
Real-time monitoring of the emission of volatile organic compounds from polylactide 3D printing filaments
PublicationEstablishing the emission profile of volatile organic compounds generated during fused deposition modeling 3D printing using polymer filaments is important in terms of both understanding the processes taking place during thermal degradation of thermoplastics, and assessing the user's exposure to potentially harmful volatiles. However, obtaining detailed, real-time qualitative and quantitative results poses a challenge. In this...
-
Post-comatose patients with minimal consciousness tend to preserve reading comprehension skills but neglect syntax and spelling
PublicationModern eye tracking technology provides a means for communication with patients suffering from disorders of consciousness (DoC) or remaining in locked-in-state. However, being able to use an eye tracker for controlling text-based contents by such patients requires preserved reading ability in the first place. To our knowledge, this aspect, although of great social importance, so far has seemed to be neglected. In the paper, we...
-
Fading Modelling in Dynamic Off-Body Channels
PublicationThis paper presents an off-body fading channel model for Body Area Networks (BANs) in indoor environments. The proposed model, which is based on both simulations and measurements in a realistic environment, consists of three components: mean path loss, body shadowing, and multipath fading. Seven scenarios in an indoor environment (a medium-size room with furniture, mostly consisting of wooden tables and chairs) have been measured:...
-
Sundials of St Mary’s Church in Gdańsk / Zegary słoneczne kościoła pw. Wniebowzięcia Najświętszej Panny Marii w Gdańsku
PublicationThe paper presents contemporary research evidence of form, function and history of the sundials of St Mary’s Church in Gdańsk. The discussed sundials are located on the southern wall of the church transept. The sundial, which is believed to be made by Lorenzo Zachau in 1533, is placed on the west side of the western window, at the edge of the wall. The face of this sundial is separated by a horizontal line into two parts. The upper...
-
Examining Government-Citizen Interactions on Twitter using Visual and Sentiment Analysis
PublicationThe goal of this paper is to propose a methodology comprising a range of visualization techniques to analyze the interactions between government and citizens on the issues of public concern taking place on Twitter, mainly through the official government or ministry accounts. The methodology addresses: 1) the level of government activity in different countries and sectors; 2) the topics that are addressed through such activities;...
-
THE APPLICATION OF PHENOMENOLOGICAL METHODOLOGY FOR DESIGNING PILE FOUNDATION IN PORT STRUCTURES
PublicationIt is of utmost importance in the design process that a suitable, safe and concurrently economic solution be chosen. Issues connected with foundations require adopting a special approach. Soil is a composite medium, and it is essential to describe as precisely as possible the interaction taking place between the subgrade and the structure. There are many design methods of pile foundation that are based on in-situ test of soils....
-
Reasons behind changes in the share of labour in national income in the Polish economy: Selected aspects
PublicationAim/purpose – The aim of this paper is to examine the impact of structural changes taking place in the Polish economy on the share of labour in national income. Design/methodology/approach – The scope of this study includes a review of the literature dedicated to the issue and an empirical analysis of data available on this topic. The study uses elements of descriptive statistics and the method of induction. Findings – The conducted...
-
A case study of odour nuisance evaluation in the context of integrated urban planning
PublicationOdour nuisance poses a serious problem in many urban areas, yet its evaluation and mitigation is often omitted in the urban planning process. By identifying its range and spatio-temporal variations, it could be taken into consideration by planners in urban development strategies and land use decisions. The aim of the study was to present the application of odour evaluation techniques in the improvement of the quality of life in...