Filtry
wszystkich: 1327
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: UNDRAINED SHEAR STRENGTH
-
Uncertainty assessment of ultimate strength of corroded stiffened plates subjected to different maintenance actions
PublikacjaThe study deals with the uncertainty assessment of different governing factors related to the ultimate strength of the corroded stiffened plates. The load-carrying capacity is predicted with the use of the nonlinear Finite Element Method. The most influencing governing factors in the non-linear FE analysis, such as material properties and initial imperfections are modeled and analysed as stochastic variables. The ultimate strength...
-
Design of poroelastic wearing course with the use of direct shear test
PublikacjaPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Resilient Interface Shear Modulus for Characterizing Shear Properties of Pavement Base Materials
Publikacja -
FE-investigation of shear localization in granular bodies under high shear rate
PublikacjaArtykuł omawia wpływ prędkości ścinania an lokalizację odkształceń wwąskiej warstwie piasku poddanej ścinaniu. Obliczenia wykonano przyzastosowaniu metody elementów skończonych i mikropolarnego modeluhipoplastycznego rozszerzonego o lepkość.
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublikacjaThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
Analysis of ultimate compressive strength of cracked plates with the use of DOE techniques
PublikacjaThe objective of this work is to investigate the structural compressive response of plates with locked cracks accounting for all relevant factors and correlation between them. The nonlinear FE model considering both geometric and material nonlinearities is employed herein, and the FE model of the structural response of intact plates is validated with the available experimental data. In the common studies, based on One Factor at...
-
Cold Cracking Of Underwater Wet Welded S355G10+N High Strength Steel
PublikacjaWater as the welding environment determines some essential problems influencing steel weldability. Underwater welding of high strength steel joints causes increase susceptibility to cold cracking, which is an effect of much faster heat transfer from the weld area and presence of diffusible hydrogen causing increased metal fragility. The paper evaluates the susceptibility to cold cracking of the high strength S355G10+N steel used,...
-
Strength analysis of a large-size supporting structure for an offshore wind turbine
PublikacjaThe offshore wind power industry is the branch of electric energy production from renewable sources which is most intensively developed in EU countries. At present, there is a tendency to install larger-power wind turbines at larger distances from the seashore, on relatively deep waters. Consequently, technological solutions for new supporting structures intended for deeper water regions are undergoing rapid development now. Various...
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublikacjaAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Determination of changes in viscosity of pectin gel depending on shear rate (1.1 to 55 s-1).
Dane BadawczeThe rheological characteristic of pectin gel (with concetration 0,45% m/m, in three independent repetition of sample) was made on the basis of a viscosity measurement using a Brookfield viscometer, using LV SC4 - 25 spindle and shear rates from 1.1 to 55 s-1.The data allowed to characterize the used hydrogel preparations and assess their functional...
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublikacjaThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
The effects of different doses of caffeine on maximal strength and strength‐endurance in women habituated to caffeine
Publikacja -
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublikacjaIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
Determination of changes in viscosity of pectin gel depending on shear rate (1.7 to 85 s-1).
Dane BadawczeThe rheological characteristic of pectin gel (with concetration 0,25% m/m, in two independent repetitions) wasmade on the basis of a viscosity measurement using a Brookfield viscometer, using LV SC4 - 27 spindle and shear rates from 1.7 to 85 s-1, in temperature of 25 C degee .The data allowed to characterize the used hydrogel preparations and assess...
-
Dynamic Signal Strength Mapping and Analysis by Means of Mobile Geographic Information System
PublikacjaBluetooth beacons are becoming increasingly popular for various applications such as marketing or indoor navigation. However, designing a proper beacon installation requires knowledge of the possible sources of interference in the target environment. While theoretically beacon signal strength should decay linearly with log distance, on-site measurements usually reveal that noise from objects such as Wi-Fi networks operating in...
-
Estimation of the Ultimate Strength of FRP Strips-to-Masonry Substrates Bond
PublikacjaFiber-Reinforced Polymers (FRP) were developed as a new method over the past decades due to their many beneficial mechanical properties, and they are commonly applied to strengthen masonry structures. In this paper, the Artificial Neural Network (ANN), K-fold Cross-Validation (KFCV) technique, Multivariate Adaptive Regression Spline (MARS) method, and M5 Model Tree (M5MT) method were utilized to predict the ultimate strength of...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublikacjaThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
The effect of shear deformations' rotary inertia on the vibrating response of multi-physic composite beam-like actuators
PublikacjaIn consecutive studies on flexomagneticity (FM), this work investigates the flexomagnetic reaction of a vibrating squared multi-physic beam in finite dimensions. It is assumed that the bending and shear deformations cause rotary inertia. In the standard type of the Timoshenko beam the rotary inertia originated from shear deformations has been typically omitted. It means the rotary inertia resulting from shear deformation is a new...
-
Anti-plane shear waves in an elastic strip rigidly attached to an elastic half-space
PublikacjaWe consider the anti-plane shear waves in a domain consisting of an infinite layer with a thin coating lying on an elastic half-space. The elastic properties of the coating, layer, and half-space are assumed to be different. On the free upper surface we assume the compatibility condition within the Gurtin–Murdoch surface elasticity, whereas at the plane interface we consider perfect contact. For this problem there exist two possible...
-
Synthesis of CoFe2O4 Nanoparticles: The Effect of Ionic Strength, Concentration, and Precursor Type on Morphology and Magnetic Properties
PublikacjaThe present study highlights the effect of metal precursor types (SO4 2¯, Cl¯, and NO3¯), their concentration, and the influence of ionic strength of reaction environment on the morphology, surface, and magnetic properties of CoFe2O4 particles. The magnetic nanoparticles were obtained by chemical coprecipitation in alkaline medium at increasing metal concentration in the range of 0.0425 mol·dm-3 to 0.17 mol·dm-3 and calcination...
-
Strength analysis of the support structure of the offshore wind turbine
PublikacjaThe global power demand from renewable sources is growing. One of a very favorable solution which meets severe environmental protection requirements are the offshore wind turbines. The offshore wind energy sector has experienced very fast development over last decade. Offshore wind farms, in comparison with onshore applications, can provide increased efficiency with reduced noise, visual, transportation and installation con-flicts....
-
Influence of water soaking on the ultimate tensile strength of polyester-based coated woven fabrics
PublikacjaThis research aims to determine the influence of water-soaking on polyester-based coated woven fabrics for ultimate tensile strength and elongation at break under uniaxial tensile tests. The paper begins with a short survey of literature concerning the investigation of the determination of coated woven fabric properties. The authors carried out the uniaxial tensile tests with an application of a flat grip to establish the values...
-
Experimental and numerical investigations of ultimate strength of imperfect stiffened plates of different slenderness
PublikacjaThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive...
-
Influence of Heat Treatment Temperature on Fatigue Toughness in Medium-Carbon High-Strength Steels
PublikacjaCurrent research has demonstrated that the tempering temperature affects the martensitic transformation of medium-carbon high-strength steels. This temperature plays an important role in the final microstructure, percentage ratios of martensite to ferrite phases and, consequently, in the mechanical properties and the fatigue response. So far, the relationship between the martensitic tempering temperature and the cyclic deformation...
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublikacjaIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
A methodology for ultimate strength assessment of ship hull girder accounting for enhanced corrosion degradation modelling
PublikacjaThe presented work shows a methodology for the ultimate strength assessment of a ship hull, considering enhanced corrosion modelling. The approach is based on the classical Smith method. However, the recent findings regarding the impact of corrosion degradation on ultimate strength are incorporated. To this end, the stress–strain relationships for particular elements composing ship hull cross-section are modified using a specially...
-
Development and application of asphalt binder relaxation test in different dynamic shear rheometers
PublikacjaIn this study, a novel relaxation test is proposed to evaluate asphalt binder low temperature properties using a Dynamic Shear Rheometer (DSR) with parallel plates of 4 mm in diameter. Three rheometers from three different manufacturers are used to analyze seven asphalt binders. Different material parameters are derived which are useful to evaluate and discriminate different asphalt binders. Test results of all three instruments...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublikacjaThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
-
Micro‑ and nano‑ bentonite to improve the strength of clayey sand as a nano soil‑improvement technique
PublikacjaNano-additives results in the formation of nano-cementation (NC). This process is recently used to improve the durability of various building materials. NC used to improve the strength of untreated soil materials, also known as nano soil-improvement (NSI). In few years, the role of nano-additives in various types of soils were developed. In this research, the role of micro- and nano- size of bentonite as soil stabilizer was evaluated...
-
Structural Reliability Assessment Of Corroded Tanker Ship Based On Experimentally Estimated Ultimate Strength
PublikacjaThis work deals with the reliability assessment of a tanker ship hull structure subjected to a vertical bending moment and corrosion degradation. The progressive collapse and ultimate load carrying capacity are estimated based on experimentally tested scaled box-shaped-specimens. The translation of the strength estimate of the scaled specimen to the real tanker ship hull structure is performed based on the dimensional theory developing...
-
Methods of solving the Atkins equation determine shear angle with taking into consideration a modern fracture mechanics
PublikacjaIn the paper are presented methods of solving nonlinear Atkins equation . The Atkins equation describe shear angle with taking into account properties of material cutting. To solve Atkins equation has been used iterative methods: Newton method and simplified method of simple iteration. Method of simple iteration is presented in the form of Java application.
-
Modelling of shear zones during quasi-static granular silo flow using material point method (MPM)
PublikacjaThe paper focuses on confined silo flow of cohesionless sand. The problem considered is a quasi-static flow in a plane strain model silo with parallel walls simulated with the material point method (MPM). The simulation used a non-local hypoplastic constitutive model. Initially, the paper validated the implemented numerical approach with basic element tests and a plane strain compression test. The subsequent MPM calculations for...
-
Jixie Qiandu/Journal of Mechanical Strength
Czasopisma -
FE investigations of the effect of fluctuating local tensile strength on coupled energetic-statistical size effect in concrete beams
PublikacjaThe effect of fluctuating local tensile strength on a coupled energetic-statistical size effect in plain concrete beams under bending was numerically investigated. First, the influence of varying autocorrelation length of the random field describing a spatial variation of local tensile strength was studied. Next, the influence of the coefficient of variation of local tensile strength was analyzed. The numerical FE investigations...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Influence of the ionic strength on the amyloid fibrillogenesis of hen egg white lysozyme
PublikacjaThe study investigates the role of the electrostatic interactions in the fibrillation of the hen egg white lysozyme (HEWL). In order to achieve this aim the influence of the cations Na+, Mg2+ and Al3+ on the amyloid fibril formation and amorphous aggregation was tested. The amyloids are formed in the solution without added salt but the Thioflavin T fluorescence gives the false-negative result. In these conditions, the HEWL fibrils...
-
Chemical Theory of Machines, basic principles of strength with examples of calculations
PublikacjaThis book encompasses the essential range of information on technical aspects of mechanical design. It was written primarily for the students and staff of chemistry faculties of technical universities, yet it may also be utilized by everyone, who ether would like to try or already enjoys designing, but cannot take advantage of typical stress & machine construction handbooks. These handbooks often require familiarity with the concepts...
-
Bending and buckling formulation of graphene sheets based on nonlocal simple first-order shear deformation theory
PublikacjaThis paper presents a formulation based on simple first-order shear deformation theory (S-FSDT) for large deflection and buckling of orthotropic single-layered graphene sheets (SLGSs). The S-FSDT has many advantages compared to the classical plate theory (CPT) and conventional FSDT such as needless of shear correction factor, containing less number of unknowns than the existing FSDT and strong similarities with the CPT. Governing...
-
Placebo Effect of Caffeine on Maximal Strength and Strength Endurance in Healthy Recreationally Trained Women Habituated to Caffeine
Publikacja -
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublikacjaThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Strength tests of steel sandwich panel.
PublikacjaPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. Technol. Okr. i Obiekt. Oceanotech. Wydz. OiO, na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze.
-
Hull strength assessment of the designed ships
PublikacjaPrzedstawiono metody i wyniki analizy wytrzymałości konstrukcji kadłubów czterech statków zaprojektowanych w ramach EUREKA Project E!2772: zbiornikowca, kontenerowca, Ro-Ro i statku rzeka-morze. Obliczenia wykonano według zaleceń i wymagań przepisów Det Norske Veritas.
-
Strength tests of steel sandwich panel
PublikacjaPrzedstawiono wyniki badań laboratoryjnych elementarnego, teowego złącza spawanego laserowo, których celem było określenie pola odkształceń i naprężeń w strefie przyspoinowej. Uzyskane wyniki wskazują na potrzebę bardzo starannego modelowania konstrukcji spawanych laserowo przy obliczeniach MES. W pracy zaprezentowano wyniki badań konstrukcji rzeczywistej pod statycznym obciążeniem ściskającym, które porównano z rezultatami analizy...
-
Strength tests of steel sandwich panel
PublikacjaPrzedstawiono wyniki badań laboratoryjnych elementarnych złączy spawanych laserowo i paneli SANDWICH, prowadzonych w Katedrze Technologii Okrętów i Obiektów Oceanotechnicznych WOiO, na konstrukcjach w skali rzeczywistej. Dokonano analizy zachowania połączenia podczas procesu obciążenia. Przedstawiono wyniki numerycznego zamodelowania własności złącza. Dokonano porównania uzyskanych rezultatów analizy numerycznej z wynikami z badań...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublikacjaThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Micro-modelling of shear localization during quasi-static confined granular flow in silos using DEM
PublikacjaThe paper deals with the quasi-static confined flow of cohesionless sand in a plane strain model silo with parallel walls and a slowly movable bottom. Numerical modelling was carried out by the discrete element method (DEM) using spheres with contact moments to approximately capture a non-uniform shape of sand particles. Different initial void ratios of sand and silo wall roughness grades were employed. Regular triangular grooves...
-
Green strength (buildability performance) of concretes containing magnetite aggregate (M0-M100) mixes
Dane BadawczeRaw data for determination of buildability (green strength) properties of concrete mixes determined by squeezing test using QuantumX MX840B with CATMAN-EASY software, determined after 15, 30, 45 and 60 minutes. Values present force and two displacement measurements by LVDT.Additionally, an Origin (*.opju) file with processed data presenting stress-strain...
-
Influence of Wood Moisture on Strength and Elastic Modulus for Pine and Fir Wood Subjected to 4-point Bending Tests
PublikacjaThe main purpose of this research paper was to determine the influence of the wood moisture on the strength and elastic modulus of pine and fir wood specimens subjected to the 4-point bending tests. Six bending tests for each wood species and for two different moisture level have been performed. Then, the advanced statistical analysis of the results has been carried out. On the basis of the obtained results, it has been noted that...
-
Composite Beams with glass and reinforced or prestressed concrete - early stage of a theorethical and experimental analysis of a shear zone
PublikacjaThe aim of this article is to present a forgoing preparation for a theoretical and experimental analysis of a shear zone of a composite beams with glass and reinforced or prestressed concrete. Authors present their current knowledge, achievements and predicted challenges in later stages of the research. Properties of component materials are presented in the context of compensating weaknesses of one material with strengths of the...
-
Examination of selected failure criteria with asymmetric shear stresses in the collapse analysis of laminated shells
PublikacjaThe paper is concerned with failure analysis of composite shells performed with the usage of the nonlinear 6‐parameter shell theory with drilling rotation degree of freedom. This special theory embodies naturally unlim-ited translations and rotations and is suitable for analysis of irregular shells for instance with various, partic-ularly orthogonal, intersections. The presence of the drilling rotation is inherently accompanied...
-
Relationship between vortex structures and shear localization in 3D granular specimens based on combined DEM and Helmholtz-Hodge decomposition.
PublikacjaRelationship between vortex structures and shear localization in 3D granular specimens based on combined DEM and Helmholtz-Hodge decomposition. Granular Matter, doi:10.1007/s10035-018-0815-0, 2018.
-
The Acute Effects of External Compression With Blood Flow Restriction on Maximal Strength and Strength-Endurance Performance of the Upper Limbs
Publikacja -
Inflow of fly ash on selected geotechnical parameters of soft soils.
Dane BadawczeThe reaserch presents the experimental results made on samples of soft soils mixed with fly ash in different proportions (10%, 20%, 30%). The files contains the data directly from direct shear aparatus and oedometer.
-
Corrugated Sheeting as a Member of a Shear Panel Under Repeated Load—Experimental Test
PublikacjaIn stressed-skin design, the cladding stiffening effect on structures is taken into account. However, the “traditional” design is more usual, wherein this effect is neglected. Even if the diaphragm actions are not regarded, in particular cases such as big sheds (and others), the parasitic (unwanted) stressed-skin action may occur with the result of leakage or even failure. The structures of this kind have already been built. Thus,...
-
Applications of permeability, oedometer and direct shear tests to the sand mixed with waste tire crumb
PublikacjaThe amount of the used waste rubbers in the world has been increasing every year, and their utilization, become a major environmental problem worldwide. The present experimental work has been performed to investigate the influence of rubber inclusion on the behavior of a sand. Geotechnical properties of the sand, and sand with tire crumb at various ratios mixtures (0%, 2.5%, 7.5%, and 15%) were investigated through a series of...
-
Tensile strength test of PE foils modified with zinc oxide and zinc salts
Dane BadawczeThis dataset contains the results of PE foils mechanical tests, in which the material was evaluated for strength and extensibility at the moment of breaking and based on the same tests preceded by material fatigue in 50 stretching cycles. The principle of the method is to stretch the test sample placed in the clamps of the stretching apparatus at a...
-
The effect of dehydration/rehydration of bacterial nanocellulose on its tensile strength and physicochemical properties
PublikacjaBacterial nanocellulose (BNC) is a natural biomaterial with a wide range of biomedical applications. BNC contains 99 % of water which makes it too thick to be used as a bioimplant material. The aim of the work was to determine the effect of the BNC dehydration followed by rehydration on its mechanical and physicochemical properties, in the context of the use of BNC as bio-prostheses in the cardiovascular system. Dehydration involved the...
-
Advanced numerical modelling for predicting residual compressive strength of corroded stiffened plates
PublikacjaAn advanced methodology for predicting the residual compressive strength of corroded stiffened plates is developed here using the non-linear finite element method. The non-uniform loss of a plate thickness is accounted for on a macro-scale. In contrast, mechanical properties are changed using the constitutive model to reflect the corrosion degradation impact on a micro-scale. Three different stiffened plate thicknesses are considered,...
-
Effect of boundary, shear rate and grain crushing on shear localization in granular materials within micro-polar hypoplasticity
PublikacjaW artykule przedstawiono wpływ 3 efektów na zachowanie się materiałów granulowanych: warunku brzegowego, prędkości ścinania oraz miażdżenia ziaren. Obliczenia wykonano przy pomocy mikropolarnego prawa hipoplastycznego rozszerzonego o efekt prędkości ścinania i miażdżenia ziaren w oparciu o teorię mechaniki zniszczenia. Szczególna uwagę zwrócono na rozkład lokalizacji odkształceń stycznych.
-
A novel one-variable first-order shear deformation theory for biaxial buckling of a size-dependent plate based on Eringen’s nonlocal differential law
PublikacjaPurpose – This paper aims to present a new one-variable first-order shear deformation theory (OVFSDT) using nonlocal elasticity concepts for buckling of graphene sheets. Design/methodology/approach – The FSDT had errors in its assumptions owing to the assumption of constant shear stress distribution along the thickness of the plate, even though by using the shear correction factor (SCF), it has been slightly corrected, the errors...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublikacjaThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
-
The influence of the carbon equivalent on the weldability of high-strength low-alloy steel in the water environment
PublikacjaFrom many years, the high strength low alloy steels are often used for offshore constructions. This constructions, due to the environment in which they work, require more frequent repairs than the constructions from the land. For economic reasons, repairs take place in the underwater conditions, however water significantly decreases the weldability of steel. The paper presents the results of the CTS weldability test for S460ML...
-
Effect of Base-Connection Strength and Ductility on the Seismic Performance of Steel Moment-Resisting Frames
PublikacjaColumn-base connections in steel moment-resisting frames (SMFs) in seismic regions are commonly designed to develop the capacity of adjoining column with an intent to develop a plastic hinge in the column member, rather than in the connection (i.e., a strong-base design). Recent research has shown base connections to possess high ductility, indicating that this practice may be not only expensive but also unnecessary. This suggests...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublikacjaThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Prediction of cast-in-place concrete strength of the extradosed bridge deck based on temperature monitoring and numerical simulations
PublikacjaThe work is devoted to the implementation of a monitoring system for high performance concrete embedded in the span of an extradosed bridge deck using a modified maturity method augmented by numerical simulations conducted by the authors’ FEM code. The paper presents all research stages of bridge construction and considers the conclusions drawn from the results of laboratory tests, field measurements, and numerical calculations....
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Study on the strength of laminated polyurethane-steel joints
Publikacja -
Grip strength is associated with markers of central hemodynamics
Publikacja -
Hydrogen degradation of high strength weldable steels
PublikacjaW pracy przedstawiono wyniki badań podatności stali spawalnych o wysokiej wytrzymałości na niszczenie wodorowe. Badano dwa gatunki stali S690Q i ich złącza spawane. Ocenę podatności na niszczenie wodorowe wykonano przy różnych rodzajach obciążeń w środowisku wody morskej przy polaryzacji katodowej.
-
Strength assessment of a version of joint of sandwich panels
PublikacjaW pracy przedstawiono propozycję optymalizacji wariantu połączenia doczołowego stalowych paneli typu ''sandwich''. Przedstawiono wyniki analizy numerycznej rozkładów naprężeń dla wielu wariantów geometrii proponowanego połączenia.
-
Hydrogen degradation of high strength weldable steels
PublikacjaW pracy przedstawiono wyniki badań podatności stali spawalnych o wysokiej wytrzymałości na niszczenie wodorowe. Badano dwa gatunki stali S690Q i ich złącza spawane. Ocenę podatności na niszczenie wodorowe wykonano w oparciu o próbę rozciągania z małą prędkością odkształcania w powietrzu i środowisku wody morskiej przy polaryzacji katodowej. Przedstawiono model niszczenia wodorowego badanych stali i ich złączy spawanych.
-
Strength characteristics of tyre chips-sand mixtures.
PublikacjaBadania w aparacie trójosiowego ściskania przy różnej zawartości wagowej kawałków zużytych opon oraz różnym ich ułożeniu w próbce piasku. Badania prowadzono przy dowolnym ułożeniu tych elementów, umieszczeniu ich poziomo oraz w systemie mieszanym. Wyznaczono optymalną zawartość kawałków opon w próbce piasku, przy której występowała maksymalna wytrzymałość na ściskanie.
-
The influence of bulk solids on buckling strength of silos.
PublikacjaW artykule przedstawiono wyniki numerycznej anlizy wyboczenia ścian silosu osiowo-symetrycznego wypełnionego materiałem sypkim. Zachowanie ściany było modelowane mikropolarnym prawem sprężysto-plastycznym, natomiast zachowanie materiału sypkiego mikropolarnym prawem hipoplastycznym. Oszacowano wpływ materiału sypkiego na nośność wyboczenia silosów.
-
Ultimate strength of stiffened plates subjected to compressive load and spatially distributed mechanical properties
PublikacjaThe present study deals with the ultimate strength of stiffened plates subjected to spatially distributed mechanical properties and compressive load. Normally, mean values of mechanical properties based on tensile tests are used to validate the numerical assessment with experimental results. However, mechanical properties may vary within a single specimen. To investigate the impact of that, random fields of yield stress and Young...
-
A model of damaged media used for describing the process of non-stationary creep and long-term strength of polycrystalline structural alloys
PublikacjaThe main laws of the processes of creep and long-term strength of polycrystalline structural alloys are considered. From the viewpoint of continuum damaged media (CDM), a mathematical model is developed that describes the processes of viscoplastic deformation and damage accumulation under creep. The problem of determining material parameters and scalar functions of the developed constitutive relations based on the results of specially...
-
Strength parameters of polyester reinforced PVC coated fabric after short term creep loading in biaxial mode
PublikacjaThis study addresses the analysis of tensile strength parameters of the technical fabric VALMEX, which is composed of two orthogonal polyester thread families (named the warp and fill) and both sides PVC coated. The material was firstly subjected to 48-hour biaxial creep loading with the equal stress level in both orthogonal directions of the fabric. The stress levels were established as follows: 4.6 kN/m, 10.4 kN/m, 16.4 kN/m,...
-
Effect of Arc Strikes on High Strength Low Alloy Steels Welded by SMAW
PublikacjaWet welding with covered electrodes (Shielded Metal Arc Welding – SMAW) is the most commonly used method of carrying out welding repair works in a water environment. Limited visibility and the inability to move freely under water result in an increased risk of formation of welding imperfections such as lack of fusion, lack of penetration and arc strikes. The work focused on changes in the properties and structure of steel subjected...
-
Comparison of target strength (TS) distributions obtained by means of the use of direct and indirect techniques in sea cages
PublikacjaThe aim of this study is to verify the reliability of a processing application developed for the indirect measurement of target strength (TS), with a view to the integration into a single-beam system for its utilization in fish farms. Dorsal and ventral measurements are carried out for gilt-head sea-bream (Spams Aurata) for 5 size classes using a split-beam EK60 echosounder and single-beam data obtained from one of the channels...
-
Investigating the combined impact of plasticizer and shear force on the efficiency of low temperature reclaiming of ground tire rubber (GTR)
PublikacjaIn the present work, ground tire rubber (GTR) was mechano-chemically reclaimed at ambient temperature using two-roll mills. Road bitumen and styrene-butadiene-styrene (SBS)-modified bitumen at variable content (in range: 2.5–20 phr) were applied as reactive plasticizers to enhance reclaiming of GTR. For better understanding the plasticizing effect of bitumen on the quality of obtained reclaimed rubber, mechano-chemically reclaimed...
-
Rheological and compressive strength (ultrasonic pulse method) properties of cement pastes containing iron oxide (Fe3O4) nanoparticles
Dane BadawczeRheological data of cement pastes containing different replacement levels of cement with iron oxide nanoparticles deterimined using MCR 301 (Anton Paar) stress-imposed rheometer, equipped with calibrated helicoidal geometry
-
On the use of the cumulative strain energy density for fatigue life assessment in advanced high-strength steels
PublikacjaIn this paper, the applicability of the cumulative strain energy density is explored as a fatigue indicator parameter for advanced high-strength steels subjected to strain-controlled conditions. Firstly, the cyclic stress-strain responses of nine steels, selected from three multiphase families, encompassing different elemental compositions and different heat treatment routes, were studied. Then, the predictive capabilities of the...
-
Reliability of nitrogen removal processes in multistage treatment wetlands receiving high-strength wastewater
Publikacjareatment wetlands have been proved to be more effective than conventional treatment processes in case of high-strength wastewater containing high concentrations of ammonium nitrogen and recalcitrant organic matter. In this study nitrogen removal processes and reliability of nitrogen removal at two identical pilot-scale multistage treatment wetlands (MTWs) receiving real, non-synthetic wastewater were discussed. The wastewater discharged...
-
The standard radiated immunity test of an astable multivibrator at a normative field strength
Dane BadawczeThe dataset presents a result of measurements that are a part of electromagnetic field immunity tests. The radiated, radio frequency, immunity tests were carried out for a typical astable electronic multivibrator. Tests of immunity of electronic systems to radiated radio frequency (RF) disturbances in the frequency range from 80 MHz to 1 GHz are performed...
-
Drill holes decrease cancellous bone strength: A comparative study of 33 paired osteoporotic human and 9 paired artificial bone samples
PublikacjaThis study was designed to compare compressive strength of cancellous bone retrieved from the femoral head in a specimen with and without guide wire hole, with comparison to synthetic bone samples. Femoral heads retrieved from 33 patients who sustained femoral neck fractures and underwent hip arthroplasty were cut into cuboids leaving two matching samples from the same femoral head. Similar samples were prepared from synthetic femurs....
-
The Acid Strength of the Lewis‐Brønsted Superacids – A QSPR Study
Publikacja -
Compressive Strength and Leaching Behavior of Mortars with Biomass Ash
Publikacja -
Hygrothermal and strength properties of cement mortars containing cenospheres
Publikacja -
Porosimetric, Thermal and Strength Tests of Aerated and Nonaerated Concretes
Publikacja -
A note on the strength and minimum color sum of bipartite graphs
PublikacjaSiłą grafu G nazywamy najmniejszą liczbę całkowitą s, taką że istniej pokolorowanie grafu G, o minimalnej sumie przy użyciu kolorów {1,...,s}. W pracy pokazano, że w grafach dwudzielnych stopnia D zachodzi oszacowanie s <= ceil(D/2) + 1. Z obserwacji tej wynika algorytm wielomianowy do obliczania siły i sumy chromatycznej w grafach dwudzielnych stopnia co najwyżej 4.
-
On a threshold induced bias in fish target strength estimation.
PublikacjaPrzedstawiono statystyczny opis zjawiska wpływu progu rejestracji ech od ryb na estymatę siły celu ryb. Pokazano sposób korekcji wykorzystujący zależności pomiędzy funkcjami rozkładu prawdopodobieństwa poziomu echa i charakterystyki wiązki. Przedstawiono wyniki symulacji.
-
Strength parameters of masonry walls in modelling historic constructions
PublikacjaThe paper presents the determination of the basic material properties of a historic brickwork. Experimental studies were used to identify the basic material properties of bricks. The mechanical properties of the masonry, as an orthotropic homogenized material, were calculated. Then, numerical simulations using the Finite Element Method (FEM) were performed to verify the experimental outcomes. Macromodels with element sizes of 40,...
-
Experimental and numerical investigations of ultimate strength of degradated structures
PublikacjaThe presented work investigates the corrosion influence on the structural behaviour of structural elements. Nine welded large-scale stiffened plates, and 30 standard small specimens have been subjected to the accelerated marine immersed conditions. After corrosion testing, the specimens have been accurately measured in terms of surface characteristics. The coupon specimens were furtherly subjected to tensile loading to develop...
-
Ultimate strength analysis of bulk carriers corrugated bulkheads
PublikacjaPrzedstawiono rozważania i obliczenia, których celem była ocena jakości standardu wytrzymałości grodzi falistych masowców, wprowadzonego w 1998 r. przez IACS i wdrożonego do konwencji SOLAS. Wykonane nieliniowe obliczenia MES nośności granicznej zginanych fal grodzi wykazują, że standard ten jest zbyt optymistyczny.
-
Hydrogen degradation of high strength low alloyed steels.
PublikacjaBadano wpływ polaryzacji katodowej na własności stali węglowej, stali o podwyższonej i wysokiej wytrzymałości metodą stałego powolnego odkształcania.Stwierdzono, że stopień kruchości wodorowej każdej z badanych stali zależał od stężenia wodoru dyfuzyjnego.
-
Testing of fatigue strength limit of slide bearing materials
PublikacjaPrzedstawiono wyniki badań wytrzymałości zmęczeniowej wybranych trójwarstwowych łożysk cienkościennych. Zaprezentowano zdjęcia typowych pęknięć zmęczeniowych warstwy stopu łożyskowego. Obliczono i oceniono krytyczne wartości naprężeń stycznych warstwy ślizgowej.
-
Hydrogen degradation of high-strength weldable steels in seawater
PublikacjaOceniono podatność na niszczenie wodorowe stali spawalnych o wysokiej wytrzymałości przy obciążeniach monotonicznie rosnących. Badano dwa gatunki stali ulepszonych cieplnie i ich złącza spawane. Przeprowadzono próby rozciągania z małą prędkością odkształcania w wodzie morskiej przy polaryzacji katodowej. Wykonano próby przenikania wodoru metodą Devanathana-Stachurskiego.
-
Hydrogen delayed cracking of high-strength weldable steels
PublikacjaOceniano podatność na niszczenie wodorowe stali 14HNMBCu o wysokiej wytrzymałości i jej połączeń spawanych przy obciążeniu stałym w wodzie morskiej. Badania przeprowadzono w powietrzu, oraz w środowisku wody morskiej przy potencjale korozyjnym i przy polaryzacji katodowej. Obecność lub brak opóźnionych pęknięć próbek z karbem przyjęto za miarę odporności na niszczenie wodorowe przy stałym obciążeniu.
-
Selected problems concerning strength of a floating dock with roof
PublikacjaW pracy przedstawiono modele i wyniki analizy wytrzymałości konstrukcji zadaszonego doku pływającego. Obliczono, że ścianki wiązarów zadaszenia, aby mogły przenieść obciążenia środowiskowe, muszą mieć grubość 24 mm. Ciężkie przesuwne segmenty zadaszenia generują w dennikach pontonu doku naprężenia sięgające 25% wartości dopuszczalnych. Wytężenie konstrukcji pontonu doku i podbudowy, obciążonych ciężarem zadaszenia i dokowanego...
-
Influence of bulk solids on the buckling strength of silo shells.
PublikacjaW artykule przedstawiono wyniki numerycznej nieliniowej analizy wyboczenia powłok silosowych pustych i wypełnionych materiałem sypkim. Obliczenia wykonano dla różnych imperfekcji w powłoce. Wyniki teoretyczne porównano z wynikami doświadczalnymi wykonanymi w Uniwersytecie Karlsruhe.
-
Analytical Buckling of FG Nanobeams on The Basis of A New One Variable First-Order Shear Deformation Beam Theory
PublikacjaIn this work, buckling analysis of functionally graded (FG) nanobeams based on a new refined beam theory has been analyzed. The beam is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new obtained beam theory has only one variable which leads to one equation similar to the Euler beam theory and also is free of any shear correction factor. The equilibrium equation has been...