Search results for: DYNAMIC PARAMETERS
-
Identification of plate dynamic parameters for structural health monitoring
PublicationPraca przedstawia technikę wyznaczania parametrów modalnych wykorzystywanych w diagnostyce konstrukcji. Modalna masa, sztywność, tłumienie i postacie drgań wyznaczone są dla prostokątnej stalowej płyty na podstawie badań eksperymentalnych. Teoretyczne parametry modalne otrzymaneo z modelu MES. Omówiony został wpływ dodatkowej masy na parametry modalne konstrukcji.This paper presents a technique for modal parameters estimation for...
-
Identification of dynamic parameters in the context of diagnostics of steel tank with different level of liquid.
PublicationThe paper presents an experimental study to identify the dynamic parameters of a water-filled tank model. The experimental modal analysis approach involving the excitation at one point of the structure and acquisition of vibra tions at selected points distri buted over the tank surface allowed to determine the resonance frequencies, mode shapes and damping ratios. The main aim of the research was to examine the influence of...
-
Robust estimation of variables and parameters in dynamic water distribution systems
PublicationPrzedstawiono estymację metodą ''set membership'' zmiennych i parametrów systemu dystrybucji wody pitnej. Zmienne odnoszą się do ilości i jakości wody, natomiast parametry odnoszą się do modelu matematycznego hydrauliki. Problemten jest wysoce nieliniowy. Algorytm estymacji jest oparty na wcześniejszychpracach i wykorzystuje również algorytm dynamicznej linearyzacji odcinkami.
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Methodology of determination of geotechnical parameters for non-cohesive soils based on dynamic and static penetration tests
PublicationPrzedstawiono zakres, metodykę i wyniki sondowań dynamicznych i statycznych podłoży niespoistych dla dwóch dużych obiektów hydrotechnicznych: terminalu przeładunku zboża w Porcie Północnym w Gdańsku i planowanego kanału żeglugowego przez Mierzeję Wiślaną. Na podstawie obu rodzajów sondowań określono parametry geotechniczne badanych gruntów, przeanalizowano je i porównano ze sobą.
-
Set membership estimation of parameters and variables in dynamic networks by recursive algorithms with moving measurment window
PublicationW artykule rozważana jest łączna estymacja przedziałowa zmiennych i parametrów w złożonej sieci dynamicznej w oparciu niepewne modele parametryczne i ograniczoną liczbę pomiarów. Opracowany został rekursywny algorytm estymacji z przesuwnym oknem pomiarowym, odpowiedni dla monitorowania sieci on-line. Okno pomiarowe pozwala na stabilizowanie klasycznego algorytmu rekurencyjnego estymacji i znacznie poprawienie obcisłości estymat....
-
ANALYSIS OF IMPACT of SHIP model parameters on changes of control quality index in ship dynamic positioning system
PublicationIn this work there is presented an analysis of impact of ship model parameters on changes of control quality index in a ship dynamic positioning system designed with the use of a backstepping adaptive controller. Assessment of the impact of ship model parameters was performed on the basis of Pareto-Lorentz curves and ABC method in order to determine sets of the parameters which have either crucial, moderate or low impact on objective...
-
CREATING A RANKING OF DIAGNOSTIC PARAMETERS FOR THE DYNAMIC PROCESS OF A MARINE COMBUSTION ENGINE IN THE ASPECT OF MULTI-CRITERIA EVALUATIONS
PublicationThe change of some of the engine’s structural parameters affects the change of toxic compound emission in exhaust gases. It mainly applies to the damage sustained by the charge exchange system as well as the fuel system and the engine supercharging system. These changes are definitely higher during dynamic states and the related transient states. As such, it is possible to speak of a diverse sensitivity of the diagnostic parameters...
-
Dynamic impedance spectra of programmable dynamically changing RC model based on digital potentiometers
Open Research DataThe dataset presents non-stationary impedance spectra of the RC model presented in the figure below. This model contains two digital potentiometers controlled digitally by the microcontroller. This solution allows to programmably control the value of the model impedance. Thanks to this, the model can be used as a test engine for evaluation of the dynamic...
-
Dynamic analysis of the railway bridge span under moving loads
PublicationThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
Dynamic charging of electric buses
PublicationDespite the continuous development of electrochemical battery technology and the multitude of electric buses on offer, it is still not possible to exploit electric buses in urban transport on an all-day basis without the necessity of charging them. It is therefore necessary to build point-to-point contact charging stations or induction charging stations at the terminals. This results in substantial financial outlays connected with...
-
Footbridges. Dynamic Design – Selected Problems
PublicationModern footbridges create challenge in esthetic and structural design. Breaking the proven canons is a recipe for architectural success. However esthetic form has to be also a functional pedestrian bridge. Therefore a good FEM modeling is a key element in engineering part of design. The paper presents selected problems related to the modeling of the dynamic construction of footbridges. Several basic dynamic problems concerning...
-
Identification of diagnostic parameter sensitivity during dynamic processes of a marine engine
PublicationChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure, but...
-
Model dynamic electrochemical impedance spectroscopy (DEIS) results obtained with various DC polarization rates
Open Research DataThe dataset contains results of model dynamic electrochemical impedance spectroscopy studies carried out on a setup of 10 diodes in series, which were connected in parallel with a condenser. The impedance data were acquired every 1 s (the analytic window length for Fourier Transform was 1 s). The model system was polarized between 0 and +8 V with DEIS...
-
Numerical analysis by FEM and analytical study of the dynamic thermal behavior of hollow bricks with different cavity concentration
PublicationThis paper presents the investigation results on the influence of the cavity concentration in hollow bricks on static and dynamic thermal parameters: a time lag, a decrement factor, an equivalent thermal diffusivity (ETD) and an equivalent thermal conductivity (ETC). The dynamic thermal behavior of hollow bricks is studied with an optimized cavity shape to reduce the intensity of radiation and convective heat exchange. The thermal...
-
Numerical analysis by FEM and analytical study of the dynamic thermal behavior of hollow bricks with different cavity concentration
PublicationThis paper presents the investigation results on the influence of the cavity concentration in hollow bricks on static and dynamic thermal parameters: a time lag, a decrement factor, an equivalent thermal diffusivity (ETD) and an equivalent thermal conductivity (ETC). The dynamic thermal behavior of hollow bricks is studied with an optimized cavity shape to reduce the intensity of radiation and convective heat exchange. The thermal...
-
Differential analysis of dynamic immittance spectra
PublicationThis work presents a new approach to the analysis of immittance spectrograms of systems characterised by non-stationarity. The possibility of linking the evolution of the immittance response with changes in the parameters describing the system is achieved by introducing a spectrum in differential form. By using the above procedure, it becomes possible to separate elements with a dependence (or lack thereof) from an independent...
-
Numerical Evaluation of Dynamic Response of a Steel Structure Model under Various Seismic Excitations
PublicationThe present paper reports the results of the study, which was designed to perform a numerical evaluation of dynamic response of a single-storey steel structure model. The experimental model was previously subjected to a number of different earthquake ground motions during an extensive shaking table investigation. The analyzed structure model was considered as a 1-DOF system with lumped parameters, which were determined by conducting...
-
THE IDENTIFICATION OF TOXIC COMPOUND EMISSION SENSITIVITY AS A DIAGNOSTIC PARAMETER DURING DYNAMIC PROCESSES OF THE MARINE ENGINE
PublicationChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure,...
-
Contribution of dynamic vehicle loads to pavement failure
PublicationPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Dynamic state assessment of the water turbine with the power of 600 kW
PublicationThe article discusses the results of experimental studies to assess the dynamic state of the turbine set with the Kaplan turbine. The dynamic assessment was made on the basis of appropriate standards, based on the measurement results of selected parameters of vibration, which have been measured for several states of the machine load. In addition, we attempted to identify the causes of the increased vibration levels based on the...
-
Sliding friction of alumina (Al2O3) with friction induced vibrations
Open Research DataTest files containing data on experiments in self mated sliding contact of alumina Al2O3 lubricated with either water or paraffin oil. Tests run in variable load/velocity conditions and with different dynamic settings of the test rig (PT-3 tribometer). The aim of the research was to attempt in finding correlations between the dynamic characteristics...
-
Parametric versus nonparametric modelling of dynamic susceptibility contrast enhanced MRI based data
PublicationDynamic tracking of a bolus of a paramagnetic agent (dynamic susceptibility contract - DSC) in MRI (magnetic resonance imaging) measurements is successfully used for assessment of the tissue perfusion and the other features and functions of the brain (i.e. cerebral blood flow - CBF, cerebral blood volume - CBV, mean transit time - MTT). The parametric and nonparametric approaches to the identification of MRI models are presented...
-
On Nonlinear Dynamic Theory of Thin Plates with Surface Stresses
PublicationWe discuss the modelling of dynamics of thin plates considering surface stresses according to Gurtin–Murdoch surface elasticity. Taking into account the surface mass density we derive the two-dimensional (2D) equations of motion. For the reduction of the three-dimensional (3D) motion equations to the 2D ones we use the trough-the-thickness integration procedure. As a result, the 2D dynamic parameters of the plate depend not only...
-
Investigation of behaviour of metal structures with polymer dampers under dynamic loads
PublicationA large number of accidents concerning structures subjected to dynamic loads have been recently observed. One of the examples of such a structure is a temporary steel grandstand erected using scaffolding system. Dynamic load that is generated by crowd movement has a significant influence on the behaviour of the structure and may lead to excessive structural vibrations. The aim of the study is to consider the idea of using polymer...
-
Dynamic Positioning System with Vectorial Backstepping Controller
PublicationThe problem of synthesis a dynamic positioning system for low frequency model of surface vessel was considered in this paper. The recursive vectorial backstepping control design was used to keep a fixed position and heading in presence of wave disturbances. The passive observer was introduced to smooth the measurements and to estimate the velocities needed for the control algorithm. Some parameters of observer were optimized off-line...
-
Novel analysis methods of dynamic properties for vehicle pantographs
PublicationTransmission of electrical energy from a catenary system to traction units must be safe and reliable especially for high speed trains. Modern pantographs have to meet these requirements. Pantographs are subjected to several forces acting on their structural elements. These forces come from pantograph drive, inertia forces, aerodynamic effects, vibration of traction units etc. Modern approach to static and dynamic analysis should...
-
Establishing Relationships between Parameters of the controlled Compaction Soil by Using Various In-Situ Tests
PublicationThe aim of research was evaluating reliable correlations between chosen soil parameters describing state of surface layers of soil. The paper presents site comparative tests based on the light falling weight deflectometer (LFWD), the static plate load tester (VSS), the dynamic probing light tester (DPL) and the bearing ratio tester (CBR in-situ) with relationships between soil state parameters. All featured in-situ...
-
Wideband Off-Body Channel Characteristics with Dynamic User
PublicationThis paper presents the preliminary results of a dynamic off-body channel characterisation study, based on wideband measurements at 5.8 GHz in an indoor environment. The Channel Impulse Response (CIR) was measured for a scenario with the user approaching and departing from the off-body antenna. A CIR deconvolution procedure was performed jointly in two polarisations, and the received signal power, Cross-Polarisation Discrimination...
-
On time-dependent nonlinear dynamic response of micro-elastic solids
PublicationA new approach to the mechanical response of micro-mechanic problems is presented using the modified couple stress theory. This model captured micro-turns due to micro-particles' rotations which could be essential for microstructural materials and/or at small scales. In a micro media based on the small rotations, sub-particles can also turn except the whole domain rotation. However, this framework is competent for a static medium....
-
Entropy function application within the selection process of diagnostic parameters of marine diesel and gas turbine engines
PublicationThe paper presents the method of conducting an analysis of the diagnostic informativeness among the parameters characterizing the observed gas dynamic processes carried out within working spaces of marine diesel and gas turbine engines. An entropy function, as the measure of uncertainty of the identified states' set of the engine unfitness was applied. Having evaluated the diagnostic information the most adequate parameters were...
-
Experimental determination of dynamic properties of cylindrical steel tank model filled with liquid
PublicationIn technical branches, such as chemical or petroleum industries, cylindrical steel tanks are essential structures used for storage of liquid products. Any failure might have disastrous consequences, therefore their safety and reliability is essential. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank used in Poland. The investigation was carried...
-
Estimation of DC motor parameters using a simple CMOS camera
PublicationDifferent components of control systems for mobile robots are based on dynamic models. In low-cost solutions such a robot is wheeled and equipped with DC motors, which have to be included in the model of the robot. The model is fairly simple but determination of its parameters needs not to be easy. For instance, DC motor parameters are typically identified indirectly using suitable measurements, concerning engine voltage, current,...
-
Analysis the Parameters of the Adaptive Controller for Quality Control of Dissolved Oxygen Concentration
PublicationThe wastewater treatment plant can be considered a dynamic large scale complex system, in which the most important control parameter is the dissolved oxygen concentration in the aerobic zone. The air is supplied to this zone by the aeration system. In the paper, both the sequencing batch reactor and the aeration system are modelled and used as plant of control performed by the cascade nonlinear adaptive control system extended...
-
Active Dynamic Thermography imaging of wound healing processes in cardio surgery
PublicationThe surgery is a branch of medicine, that is integrally connected to wounds. Despite using sterile tools and compliance with aseptic rolls, some of the surgery wounds become infected. In clinical practice there is a lack of cheap, objective methods and tools for quantitative definition and estimation of the surgery wound healing progress. This paper presents preliminary results of Active Dynamic Thermography (ADT) parametric imaging...
-
Aerodynamic Shape Optimization for Delaying Dynamic Stall of Airfoils by Regression Kriging
PublicationThe phenomenon of dynamic stall produce adverse aerodynamic loading which can adversely affect the structural strength and life of aerodynamic systems. Aerodynamic shape optimization (ASO) provides an effective approach for delaying and mitigating dynamic stall characteristics without the addition of auxiliary system. ASO, however, requires multiple evaluations time-consuming computational fluid dynamics models. Metamodel-based...
-
Numerical investigation on dynamic response of a steel lattice tower under various seismic events
PublicationThe present paper presents the results of the numerical study designed to investigate the soil-structure flexibility effects on modal parameters (i.e. fundamental frequencies) and time-history analysis response (represented by the top relative displacements) of a 46.8 m high steel lattice tower subjected to a number of ground motions including also one mining tremor. In addition to the fixed-base condition, three different soil...
-
Numerical Investigation on Dynamic Performance of a Multi-storey Steel Structure Model and Comparison with Experimental Results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Numerical investigation on dynamic performance of a multi-storey steel structure model and comparison with experimental results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Active dynamic thermography method for TRAM flap blood perfusion mapping in breast reconstruction
PublicationThis paper presents the new method of the transverse rectus abdominis musculocutaneous flap blood perfusion mapping based on the active dynamic thermography. The method is aimed at aiding a surgeon during breast reconstruction procedure. A pair of dTnorm and t90_10 parameters were used as parametric image descriptors of the flap blood perfusion. The method was tested on 38 patients that were subjected to breast reconstruction procedure....
-
Finite element modeling of plastic hinges based on ductility demand-capacity method using nonlinear material for dynamic analysis
PublicationThe article discusses modeling plastic hinges in reinforced concrete interme-diate supports using finite elements methods. The ductility demand-capacitymethod was used to determine the geometrical parameters of cross-section plas-ticization zones, their ability to move and rotate, as well as their ductility. Dueto the varied geometry and stiffness of the supports and their nonlinear behav-ior under dynamic load, this method was...
-
Identyfikacja parametrów dynamicznych want mostu Rędzińskiego we Wrocławiu
Publicationthe paper presents results of dynamic analysis conducted on stay-cables of rędziński bridge in wrocław. identified in situ dynamic parameters (natural frequency and logarithmic decrement damping ratio) of selected stays were and compared to the values featured in the project.
-
Development and application of asphalt binder relaxation test in different dynamic shear rheometers
PublicationIn this study, a novel relaxation test is proposed to evaluate asphalt binder low temperature properties using a Dynamic Shear Rheometer (DSR) with parallel plates of 4 mm in diameter. Three rheometers from three different manufacturers are used to analyze seven asphalt binders. Different material parameters are derived which are useful to evaluate and discriminate different asphalt binders. Test results of all three instruments...
-
Determination of the dynamic critical maneuvering area in an encounter between two vessels: Operation with negligible environmental disruption
PublicationThis paper introduces the concept of Collision Avoidance Dynamic Critical Area (CADCA) for onboard Decision Support Systems (DSS). The indicator proposed is derived via identification of a minimum required maneuvering zone in an encounter between two vessels. The CADCA model accounts for ship maneuvering dynamics and associated hydrodynamic actions emerging from different rudder angles and forward speed effects. The method presented...
-
Static and Dynamic Mechanical Properties of 3D Printed ABS as a Function of Raster Angle
PublicationDue to the rapid growth of 3D printing popularity, including fused deposition modeling (FDM), as one of the most common technologies, the proper understanding of the process and influence of its parameters on resulting products is crucial for its development. One of the most crucial parameters of FDM printing is the raster angle and mutual arrangement of the following filament layers. Presented research work aims to evaluate different...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublicationThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Fading Modelling in Dynamic Off-Body Channels
PublicationThis paper presents an off-body fading channel model for Body Area Networks (BANs) in indoor environments. The proposed model, which is based on both simulations and measurements in a realistic environment, consists of three components: mean path loss, body shadowing, and multipath fading. Seven scenarios in an indoor environment (a medium-size room with furniture, mostly consisting of wooden tables and chairs) have been measured:...
-
The influence of dynamic load changes on temporary impedance in hydrogen fuel cells, selection and validation of the electrical equivalent circuit
PublicationTo achieve optimal performance of a fuel cell, a reliable monitoring and diagnostic method is required. The currently utilized methods give limited information or they are impossible to use under dynamic working conditions. To obtain comprehensive information about the fuel cell operation we utilized novel dynamic electrochemical impedance spectroscopy. Impedance measurements in dynamic mode were performed on a hydrogen fuel cell,...
-
Soil-structure interaction effects on modal parameters of office buildings with different number of stories
PublicationThe paper summarizes the results of a numerical investigation designed to study the soil-structure interaction effects on modal parameters of three office buildings. The reinforced-concrete 4-storey, 8-storey, and 12-storey office buildings, each with additional two levels of embedded basements, represent low, medium, and high-rise structures, respectively. In order to conduct this research, detailed finite-element structure models...
-
Dynamics of the small-span railway bridge under moving loads
PublicationThe paper presents the results of dynamic analysis of the small-span railway bridge, subjected to an action of moving trains. Numerical simulations were performed using three different load models: series of moving forces, series of moving single-mass and double-mass oscillators. The parameters of the vehicle were taken from the existing EN57 train. The parameters of the bridge were taken from the existing steel span of 10,24 m...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
Dynamic modeling of non-cylindrical curved viscoelastic single-walled carbon nanotubes based on the second gradient theory
PublicationThis paper is devoted to the theoretical study of the dynamic response of non-cylindrical curved viscoelastic single-walled carbon nanotubes (SWCNTs). The curved nanotubes are largely used in many engineering applications, but it is challenging in understanding mechanically the dynamic response of these curved SWCNTs when considering the influences of the material viscosity. The viscoelastic damping effect on the dynamic response...
-
Dynamic impedance measurements of the Direct Methanol Fuel Cell cathode at various operating temperatures
PublicationThis article discusses the application of impedance analysis for diagnosing the cathode of a direct methanol fuel cell at various operating temperatures. The Dynamic Electrochemical Impedance Spectroscopy technique coupled with a linear current scan was applied for this purpose. This technique allowed the observation of changes in the cathode's properties in the fuel cell operating under real working conditions. An equivalent model...
-
Research on the effect of low-sulphur marine fuels on the dynamic characteristics of a CI engine
PublicationThe implementation of low-sulphur, so-called modified marine fuels into operation requires prior labora- tory engine tests to assess the energy, emission and structural effects of their usage. This type of research are carried out on the test bed of a diesel engine as a small-scale physical model that reproduces the adequate design and process (parametric) features of a full-size marine engine. Their key stage is to determine the energy...
-
3D knee model M with decreased material parameters of the cartilage and menisci - input text file for computation
Open Research DataThe finite element method was used to simulate the stance phase of the gait cycle. An intact knee model was prepared based on magnetic resonance scans of the left knee joint of a healthy volunteer. In the model M the material parameters of cartilage and menisci were reduced to simulate degenerative changes in the medial knee osteoarthritis. The file...
-
Development Of Dynamic Method For Evaluation Of Corrosion Rate On The Example Of Organic Corrosion İnhibitor
PublicationMeasurements of the corrosion rate belong to the most important aspects of materials science. In order to reduce material loss corrosion inhibitors are used. However selection of proper inhibitor should be based on evaluation of its mechanism and effective concentrations. Mechanism of inhibition usually has dynamic character so physicochemical parameters are changing in time. Most of actually used methods...
-
Influence of the Square Wave Voltage on Dynamical Properties of a Flat Voltammetric Electrode in the Time Domain by the Electrochemical Reversible Reaction
PublicationIn this article there is a presentation of the analysis of the polarizing voltage shape influencing dynamic properties of voltammetric electrodes when on their surface reversible reaction takes place in the time domain. The electrode polarization with linearly increasing voltage and with a square component, was analyzed. The analysis that were conducted showed that the voltammetric electrode behaves like a first order transducer....
-
Application of Pierson-Moskowitz wave spectrum to solution differential equations of multihull vessel
PublicationMotion of a dynamic system can be generated by different external or internal factors. At mathematical modelling external excitation factors of the most significant effect on the system, are selected. Such external factors are usually called excitations. Response of the system to given excitations is mathematically characterized by a definite transformation called operator of a system. For a broad class of dynamic systems the...
-
Investigation of the electrochemical behaviour of AA1050 aluminium alloy in aqueous alkaline solutions using Dynamic Electrochemical Impedance Spectroscopy
PublicationThe paper presents the electrochemical behaviour of aluminium alloy AA1050 in aqueous alkaline media in the pH range 14–8.5. Electrochemical study was applied in order to obtain comprehensive information on the mechanism and kinetics of the process of anodic dissolution of aluminium, supplemented by monitoring of surface topography using an electron microscope. The corrosion rate of AA1050 increases with increasing concentration...
-
FTIR spectra and IGC chromatograms for chemically reduced graphene oxide aerogels (rGOA)
Open Research DataThe effect of selected synthesis parameters on reduced graphene oxide aerogels properties was investigated using Fourier-transform infrared spectroscopy and dynamic adsorption method (Inverse Gas Chromatography, IGC). Samples were synthesized by sol-gel method by reduction induced self-assembly of graphene oxide. As a reductant l-ascorbic acid was used....
-
A Method of Assessment of the Liquid Sloshing Impact on Ship Transverse Stability
PublicationLiquid sloshing phenomenon taking place in partly filled ships? tanks directly affects the stability of a vessel. However, only static calculations are carried out onboard ships nowadays and static transfer of liquid weight is taken into account in the course of routine stability calculation. The paper is focused on a dynamic heeling moment due to liquid sloshing in tanks onboard ships. The set of numerical simulations of liquid...
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublicationIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
Load testing of a suspended footbridge in Radom (Poland)
PublicationThe footbridge in Radom is a suspended bridge of an interesting architectural form. The structure was de-signed for 4 kN/m2 of crowd loading. Dynamic calculations were not included in the design. The structure’s acceptance tests took place on the 14th of October 2016. The behaviour of the footbridge in static testing met the expectations. Unfortunately, as a result of dynamic tests, dangerous behaviour of the footbridge was revealed....
-
Comparison of experimental and numerical results on metallic plates subjected to explosions
PublicationA comparative study of dynamic response including damage and rupture processes of thin metallic plates subjected to shockwave impulses - explosions is presented. The results of the finite element numerical analysis are related to experiments. Due to high strain rate during explosions the elasto-viscoplastic Chaboches constitutive law including damage effects has been applied. For the assumed model proper material parameters identification...
-
On rotary inertia of microstuctured beams and variations thereof
PublicationWe discuss the classic rotary inertia notion and extend it for microstructured beams introducing new microinertia parameters as an additional dynamic response to microstructure changes. Slender structures made of beam- or platelet-lattice metamaterials may exhibit not only large translations and rotations but also general deformations of inner structure. Here we considered a few examples of beam-like structures and derive their...
-
3D model of osteoarthritic (OA) knee joint for analysis of the medial meniscus biomechanics - input text file for computation
Open Research DataThe finite element method was used to simulate the stance phase of the gait cycle. An intact knee model was prepared based on magnetic resonance scans of the left knee joint of a healthy volunteer. In the OA model thickness of articular cartilage and material parameters of the cartilage and menisci were reduced to simulate degenerative changes in the...
-
DETERMINING THE TIME CONSTANT USING TWO METHODS AND DEFINING THE THERMOCOUPLE RESPONSE TO SINE EXCITATION OF GAS TEMPERATURE
PublicationThis paper describes the two methods of determining the time constant of type K thermocouple, for two construction solutions: the exposed weld and the mantle fillet weld. This is an important parameter indicating the response time of the thermocouple on the recorded signal. The first method consists of determining the value of τ in the way of numerical simulation of heat exchange between the thermocouple and the current of gas...
-
Nonlinear viscoelasticity in Three Dimensional filler reinforced rubber composites and nanocomposites
PublicationThis chapter describes the influence of three-dimensional nanofillers used in elastomers on the nonlinear viscoelastic properties. In particular, this part focuses and investigates the most important three-dimensional nanoparticles, which are used to produce rubber nanocomposites. The rheological and the dynamic mechanical properties of elastomeric polymers, reinforced with spherical nanoparticles, like POSS, titanium dioxide and...
-
Simplified Method of Modelling Behaviour of Ship in Waves with Partially Flooded Compartments
PublicationThis paper contains a description of a numerical model for calculating behaviour of ships in waves. There are many models available, but the one described here can be characterised with a set of parameters that have a decisive impact on the final values of roll motion amplitude and frequency. In this paper, it is shown how a fitting of a standard-shape hull characterised by certain readily available parameters affects...
-
Online urban acoustic noise monitoring system
PublicationConcepts and implementation of the Online Urban Noise Monitoring System are presented. Principles of proposed solution used for dynamic acoustical maps creating are discussed. The architecture of the system and the data acquisition scheme are described. The concept of noise mapping, based on noise source model and propagation simulations, was developed and employed in the system. Dynamic estimation of noise source parameters utilized...
-
Interactions using passive optical proximity detector
PublicationIn this paper we evaluated the possible application of a passive, optical sensor as an interface for human-smart glasses interactions. The designed proximity sensor is composed of set of photodiodes and the appropriate hardware and software components. First, experiments were performed for the estimations of such parameters as distance to an object, its width and velocity. Achieved results were satisfactory. Therefore, next, a...
-
Improvement of Performance Level of Steel Moment-Resisting Frames Using Tuned Mass Damper System
PublicationIn this paper, parameters of the tuned mass dampers are optimized to improve the performance level of steel structures during earthquakes. In this regard, a six-story steel frame is modeled using a concentrated plasticity method. Then, the optimum parameters of the Tuned Mass Damper (TMD) are determined by minimizing the maximum drift ratio of the stories. The performance level of the structure is also forced to be located in a...
-
Control of nonlinear and linearized model of self-balancing electric motorcycle
PublicationSelf-Balancing Electric Motorcycle (SBEM) is a dynamic and nonlinear electro-mechanical system. In this paper, the process of mathematical modelling and line-arization of SBEM is presented. The model of the control system in Matlab envi-ronment is implemented. The control system using the PID controller is designed. The operation of particular structures of the PID controller on the simulation model is compared. Due to simulation...
-
Automatic Identification System (AIS) Dynamic Data Integrity Monitoring and Trajectory Tracking Based on the Simultaneous Localization and Mapping (SLAM) Process Model
PublicationTo enhance the safety of marine navigation, one needs to consider the involvement of the automatic identification system (AIS), an existing system designed for ship-to-ship and shipto- shore communication. Previous research on the quality of AIS parameters revealed problems that the system experiences with sensor data exchange. In coastal areas, littoral AIS does not meet the expectations of operational continuity and system availability,...
-
Parametric Study on a Performance of a Small Counter-Rotating Wind Turbine
PublicationA small Counter-Rotating Wind Turbine (CRWT) has been proposed and its performancehas been investigated numerically. Results of a parametric study have been presented in this paper.As parameters, the axial distance between rotors and a tip speed ratio of each rotor have been selected.Performance parameters have been compared with reference to a Single Rotor Wind Turbine (SRWT).Simulations were carried out with Computational Fluids...
-
Experimental investigations and simulations of the microturbine unit with permanent magnet generator
PublicationIn dispersed power generation, low power devices are used for local combined generating of heat end electric power. There are developing concepts of micropower plants with electric generators driven by steam or gas microturbines. The paper presents the results of an experimental investigations of the microturbine set consists of the turbine with partial admission, permanent magnet generator and three phase AC-to-DC rectifier. The...
-
Load Tests of the Movable Footbridge Over the Port Canal in Ustka
PublicationThe paper presents the acceptance tests carried out on the open footbridge over the port canal in the Port of Ustka. The steel footbridge construction is created by a single pylon to which a movable truss span is suspended with a theoretical span of 52.3 m. The studies about load test of the object included static and dynamic extortion and measurements. In static tests the ballast was of pallets with concrete blocks. Dynamic studies...
-
A comprehensive evaluation of mimosa extract as a corrosion inhibitor on AA6060 alloy in acid rain solution: part I. Electrochemical AC methods
PublicationThe inhibition effect of mimosa extract on the corrosion of AA6060 aluminum alloy in acid rain solution was investigated by electrochemical impedance spectroscopy and dynamic electrochemical impedance spectroscopy (DEIS). All the studied electrochemical parameters showed good corrosion inhibitive characteristics with respect to the aluminum alloy in the tested solution. Inhibitor efficiency increased with the concentration and...
-
On tracking properties of real-valued generalized adaptive notch filters
PublicationGeneralized adaptive notch filters (GANFs) are used for identification/tracking of quasi-periodically varying dynamic systems and can be considered an extension, to the system case, of classical adaptive notch filters. The paper presents results of local performance analysis of a real-valued GANF algorithm, i.e., algorithm designed to track parameters of a real-valued system. This is an extension of the previous work which focused...
-
Characteristics of the polarised off-body channel in indoor environments
PublicationThis paper addresses the depolarisation effect in off-body body area networks channels, based on measurements performed at 2.45 GHz in an indoor environment. Seven different scenarios, involving both static and dynamic users, were considered, taking a statistical perspective. The analysis of the cross-polarisation discrimination is performed, as well as the analysis of path loss in co- and cross-polarised channels. Results show...
-
Influence of separation gap on the structural response of colliding structures under earthquake excitation
PublicationThe high level of urbanization in the XXIst century forces the designers to design closely-separated structures and to take into account many factors influencing their response during seismic excitation, which are the most unpredictable loads which can affect civil engineering structures. Interactions between insufficiently adjacent buildings, known as the earthquake-induced structural pounding, may cause serious damage to the structures,...
-
The dataset of coupling coefficients for rotating receiver of multicoil dynamic wireless power transfer system
Open Research DataThe provided dataset is part of the simulation results shown in related journal paper "Optimal Rotating Receiver Angles Estimation for Multicoil Dynamic Wireless Power Transfer".
-
Analysis of Properties of an Active Linear Gesture Sensor
PublicationBasic gesture sensors can play a significant role as input units in mobile smart devices. However, they have to handle a wide variety of gestures while preserving the advantages of basic sensors. In this paper a user-determined approach to the design of a sparse optical gesture sensor is proposed. The statistical research on a study group of individuals includes the measurement of user-related parameters like the speed of a performed...
-
Electromagnetic forced vibrations of composite nanoplates using nonlocal strain gradient theory
PublicationThis article is intended to analyze forced vibrations of a piezoelectric-piezomagnetic ceramic nanoplate by a new refined shear deformation plate theory in conjunction with higher-order nonlocal strain gradient theory. As both stress nonlocality and strain gradient size-dependent effects are taken into account using the higher-order nonlocal strain gradient theory, the governing equations of the composite nanoplate are formulated....
-
ENERGY ANALYSIS OF PROPULSION SHAFT FATIGUE PROCESS IN ROTATING MECHANICAL SYSTEM PART I TESTING SIGNIFICANCE OF INFLUENCE OF SHAFT MATERIAL FATIGUE EXCITATION PARAMETERS
PublicationThe article discusses the problem of mathematical modelling of energy conversion processes in a rotating mechanical system for the purpose of identifying fatigue states of propulsion shafts in this system. A simplified physical model of the analysed system, constructed in an appropriate scale, has made the basis for the experimental research. The research programme took into consideration mechanical fatigue excitation of the model...
-
Fading Analysis in Off-Body Channels in a Straight Metallic Corridor in a Passenger Ferry Environment
PublicationThis paper presents a fading analysis for Body Area Networks off-body communications at 2.45 GHz in a passenger ferry environment. The results are based on measurements performed for dynamic scenarios in a straight metallic corridor. Two components, extracted from instantaneous system loss values, have been analysed: small- and large-scales fading, separately for each scenario. Well-known probability distribution functions have...
-
Investigation on Damage-Involved Structural Response of Colliding Steel Structures during Ground Motions
PublicationEarthquakes are the most unpredictable damaging loads which can affect civil engineering structures. Due to insufficient separation distance between adjacent structures with different dynamic properties, structural collisions may occur during ground motions. Although the research on structural pounding has recently been much advanced, the studies have mainly been conducted for concrete structures. The aim of this paper is to show...
-
Application of polymer element in reduction of temporary steel grandstand vibrations
PublicationThe numerical analysis focused on reduction of vibrations of a temporary steel scaffolding grandstand has been conducted in this paper. These types of structures are regularly subjected to dynamic loads which, in conjunction with light and quite slender structural members, may induce dangerous vibrations. To increase their safety, temporary steel grandstands are usually strengthened with the diagonal stiffeners of tubular cross...
-
Incremental dynamic analysis and fragility assessment of buildings founded on different soil types experiencing structural pounding during earthquakes
PublicationThe effect of the soil type on buildings experiencing pounding during earthquakes is investigated in this study using the incremental dynamic analysis and fragility assessment methods. Three 3-D structures with different number of storeys (4, 6 and 8) were considered in this study. Three pounding scenarios between these three buildings were taken into account, i.e. pounding between 4-storey and 6-storey buildings, between 4-storey...
-
Badanie modułu odkształcenia podłoża gruntowego w nasypie kontrolowanym za pomocą płyty statycznej i lekkiej płyty dynamicznej
PublicationW praktyce inżynierskiej, zarówno projektowej, jak i wykonawczej, niewątpliwie przydatne są korelacje między parametrami geotechnicznymi. Artykuł przedstawia polowe badania porównawcze lekką płytą dynamiczną (LFWD) oraz płytą statyczną (VSS), wraz określeniem zależności korelacyjnych pomiędzy modułem odkształcenia podłoża wyznaczonym za pomocą lekkiej płyty dynamicznej EVd oraz pierwotnym i wtórnym modułem odkształcenia EV1, EV2....
-
Selected problems of sensitivity and reliability of a jack-up platform
PublicationThe paper deals with sensitivity and reliability applications to numerical studies of an off-shore platform model. Structural parameters and sea conditions are referred to the Baltic jack-up drilling platform. The study aims at the influence of particular basic variables on static and dynamic response as well as the probability of failure due to water waves and wind loads. The paper presents the sensitivity approach to a generalized...
-
Modelling and Measurement of Folk Guitar: Truss Rod and Strings in Numerical Analysis of Tone
PublicationThe study makes an attempt to model a complete vibrating guitar including its non-linear features, specifically the tension-compression of truss rod and tension of strings. The purpose of such a model is to examine the influence of design parameters on tone. Most experimental studies are flawed by uncertainties introduced by materials and assembly of an instrument. Since numerical modelling of instruments allows for deterministic...
-
The adaptive backstepping control of PMSM supplied by current source inverter for the field weakening region
PublicationThe sensorless control system of permanent magnet synchronous motor PMSM supplied by current source inverter for field weakening operation is presented in this paper. The adaptive backstepping control system and the backstepping speed observer are presented. The control system is based on multi-scalar variables. The control variables are: dc-link voltage and the output current vector pulsation. The control system was named voltage...
-
Thermo-resonance analysis of an excited graphene sheet using a new approach
PublicationForced vibration of graphene nanoplate based on a refined plate theory in conjunction with higher-order nonlocal strain gradient theory in the thermal environment has been investigated. Regarding the higher-order nonlocal strain gradient theory, both stress nonlocality and size-dependent effects are taken into account, so the equilibrium equations which are governing on the graphene sheet have been formulated by the theory....
-
Analysis of temporary steel grandstand with different bracing systems exposed to crowd load
PublicationGrandstands are structures which are regularly subjected to dynamic loads generated by crowd motions. It is a dangerous situation when spectators induce rhythmic jumping, dancing, stamping, etc. If the synchronized movement of spectators excites a natural frequency of the structure, resonant response might occur. To avoid such situations, temporary steel grandstands are commonly strengthened using additional elements that create...
-
Badania eksperymentalne modelu zbiornika stalowego na stole sejsmicznym = Experimental study on steel tank model using shaking table
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is really crucial because any failure may have serious consequences. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, rockburst-induced ground motions are usually considered to be less severe due to lower...
-
Considerations about the applicability of the Reynolds equation for analyzing high-speed near field levitation phenomena
Publicationequation for analyzing near field levitation (NFL) phenomena. Two separate approaches were developed, experimentally verified, and applied to meet the research objective. One was based on the Reynolds equation and the other was based on general conservation equations for fluid flow solved using computational fluid dynamic (CFD). Comparing the calculation results revealed that, for certain operating conditions, differences in the...
-
Employment of passive sampling in monitoring indoor air quality in selected residences in a Tri-city area in Poland
PublicationTime-weighted average concentrations of selected volatile compounds were measured in chosen residences in a Tri-City area of Poland by means of passive sampling. The results were compared to those obtained by dynamic technique – sorption tubes filled with Tenax TA sorbent. Results obtained by employing the two techniques were similar. Total volatile organic compound (TVOC) parameters were also determined. An attempt was also...
-
Monitoring of volatile organic compounds (VOCs) in atmospheric air. Part II. Sample collection and preparation
PublicationThe paper reviews literature information on air sampling techniques commonly used for monitoring volatile organic compounds (VOCs) levels in atmospheric air. It describes containers for collecting samples of atmospheric air, such as vacuum canisters and bags made from synthetic materials. It discusses dynamic, passive and denudational techniques for sampling analytes from air combining isolation with preliminary enrichment, and...
-
Instantaneous impedance monitoring of synergistic effect between cavitation erosion and corrosion processes
PublicationThe most common method of determination of cavitation erosion resistance as well as the magnitude of erosion-corrosion synergistic interaction is based on the weight loss measurements. Nondestructive characterization of installations elements is in most cases impossible to perform. Also, such a measurement does not include local types of failure or alteration of operating conditions. There is an urge to elaborate a method for monitoring...