Search results for: SPRAY TIP PENETRATION
-
Application of Box–Behnken design in the optimization of a simple graphene oxide/zinc oxide nanocomposite-based pipette tip micro-solid phase extraction for the determination of Rhodamine B and Malachite green in seawater samples by spectrophotometry
Publication -
The Ellenbogen's "Matter as Software" Concept for Quantum Computer Implementation: II Bonding Between the C60 and X@C60 Molecules as Available Molecular Building Blocks (MBBs) for Tip-Based Nanofabrication (TBN) of Quantum Computing Devices
PublicationThe binding energy, BE of the X@C60-X@C60 homodimer and the X@C60-Y@C60 heterodimer resulting from the bond formation between the occupied X@C60 MBB and the C60 molecule was studied by means of semiempirical PM7 calculations, where X and Y denote atoms from H to Bi, excluding Tc and lanthanides. All possible combinations of N = 68 guest atoms were considered, which resulted in K = 2346 of different calculated dimers of (X@C60-Y@C60)...
-
Rafał Leszczyna dr hab. inż.
PeopleDr hab. Rafal Leszczyna is an associate professor at Gdansk University of Technology, Faculty of Management and Economics. He holds the M.Sc. degrees of Computer Science and Business Management. In December, 2006 he earned a Ph.D. in Computer Science, specialisation - Computer Security at the Faculty of Electronics, Telecommunications and Informatics of Gdansk University of Technology. Between 2004 and 2008 he worked in the European...
-
Evaluation of organic coatings condition with AFM-based method
PublicationThe paper presents an atomic force microscopy (AFM)-based approach to evaluation of local protective properties of organic coatings. Apart from topography, it provides local ac and dc characteristics of examined coating. The method consists in application of ac voltage perturbation signal between conductive AFM tip and coated metal substrate. The resulting current is used to determine local impedance characteristics. Both impedance...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublicationReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
Discussion on “Coupled effective stress analysis of insertion problems in geotechnics with the Particle Finite Element Method” by L. Monforte, M. Arroyo, J.M. Carbonell, and A. Gens
PublicationAddressed here is the Particle Finite Element Method (PFEM) modelling of undrained CPTu penetration with regard to a reference analytical solution based on the Spherical Cavity Expansion Method (SCEM). Also discussed is the choice of the soil model and its parameters. The effect of cone interface friction on CPTu simulation is analyzed in a series of penetration tests using Arbitrary Lagrangian-Eulerian (ALE) and Updated Lagrangian...
-
Discussion of “CPT Evaluation of Yield Stress Profiles in Soils” by Shehab S. Agaiby and Paul W. Mayne
PublicationVeryfication of the procedure to estimate overconsolidation ratio in sands using the results of mini-cone penetration tests in centrifuge.
-
Low temperature deposition of dense MnCo 2 O 4 protective coatings for steel interconnects of solid oxide cells
PublicationIn this work manganese cobalt spinel (MnCo2O4) coatings were deposited on steel substrates by spray pyrolysis at 390 °C. This is at much lower temperatures than previously reported (typically in excess of 900 °C). It was possible to produce coatings with well controlled thickness (2-5-10 μm). The as-deposited coatings were evaluated for their microstructural changes and electrical conductivity up to 800 °C. Results confirm the...
-
Colvolutional calibration of AFM probe
Open Research DataAtomic force microscopy is based on the interaction of the examined surface with a probe of a pyramidal shape, tipped with a sharp end with a radius of curvature ranging from single nanometers to hundreds of nanometers. The resolution of the obtained image is of course dependent on the above-mentioned geometric size, and the resulting image is a convolutional...
-
A conceptual design and numerical analysis of the mixerless urea-SCR system
PublicationIn the present study, an innovative design of the urea-selective catalytic reduction (SCR) system without conventional mixing elements was developed. The aim was to obtain a high degree of urea decomposition, and uniform ammonia distribution at the inlet to the catalyst, while minimising the liquid film deposition and keeping the compact design. The concept of the design was based on creating high turbulences and elongating...
-
Mechanical properties of single V2O5 nanocrystal - nanoindentation measurement in control of the max-depth
Open Research DataThe DataSet contains the nanoindentation curves (indentation force Fn vs penetrationPd) for a single V2O5 nanocrystal supported on a substrate. The measurements were performed in control of the maximum depth of Berkovich indenter penetration: 60, 70, and 100 nm.
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Near-Infrared III Nanophosphorswith Cr3+Ni2+ Energy Transfer for Bioimaging
Open Research DataIn the biomedical field, the use of fluorescence imaging in the second near-infrared (NIR-II) region is growing rapidly because it imparts the advantages of reduced autofluorescence and low photon scattering. The advantage of reduced scattering is that it increases penetration depth in vivo and improves imaging clarity. Herein, this work uses mesoporous...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublicationCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublicationCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Wpływ termoplastycznych kompozycji napełnianych miałem gumowym na wybrane właściwości asfaltu drogowego
PublicationDynamiczny rozwój transportu samochodowego zmusza do wykonywania nawierzchni drogowych z materiałów o wysokiej wytrzymałości oraz odporności na odkształcenia trwałe, co znacznie wydłuża żywotność nawierzchni. Polskie przedsiębiorstwo BISEK Sp. z o.o. z Wrocławia we współpracy z Politechniką Wrocławską, jako pierwsze wykorzystało miał gumowy do modyfikacji asfaltów metodą mokrą. W chwili obecnej firma Lotos Asfalt Sp. z o.o. wprowadziła...
-
Large deformation modelling of CPT probing in soft soil—pore water pressure analysis
PublicationThis paper presents the results of finite element modelling with Updated Lagrangian formulation of the Cone Penetration Test in soft soil deposit located in Jazowa, Poland. The numerical calculations are carried out for homogenous, normally consolidated, organic soil layer. The Modified Cam Clay constitutive model for soft soil and Coulomb model for interface are used. The study compares the registered pore water pressure distributions...
-
Scrutiny of power grids by penetrating PV energy in wind farms: a case study of the wind corridor of Jhampir, Pakistan
PublicationThis study examines the problems caused by intermittent renewable energy sources, especially wind farms, and suggests a different solar energy penetration strategy to improve their loading capacity. The study uses real-time data from a wind farm in Jhampir, Pakistan, to analyse and assess various aspects of grid stations connected to wind farms. Electrical Transient Analyzer Program is used to validate the results by linking...
-
Scrutiny of power grids by penetrating PV energy in wind farms: a case study of the wind corridor of Jhampir, Pakistan
PublicationThis study examines the problems caused by intermittent renewable energy sources, especially wind farms, and suggests a different solar energy penetration strategy to improve their loading capacity. The study uses real-time data from a wind farm in Jhampir, Pakistan, to analyse and assess various aspects of grid stations connected to wind farms. Electrical Transient Analyzer Program is used to validate the results by linking these...
-
Microencapsulation of fish oil – determination of optimal wall material and encapsulation methodology
PublicationFor the first time, we present a meta-analysis of experimental and literature data to determine which microencapsulation methodology, and which wall material are best suited to protect fish oil. Our analysis covered a period of several decades of research (1984–2018). The analysis was conducted on 196 literature data-points, and 16 data-points determined experimentally for this publication. PLS regression was used to determine...
-
High-efficient, zero-emission energy production
PublicationThis paper presents innovative thermodynamiccycles with high-efficient, zero-emission energy production. The main aim of this work is to show the role of nano-phenomena in the enhancement of the power of thermodynamic cycles. For that purpose, the cycles using oxy-combustion and spray ejected condensation are first studied and, secondly hybrid cycles using fuel cells and gas turbines are presented. The role of nano-phenomena in...
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublicationUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Nanocrystalline diamond sheets as protective coatings for fiber-optic measurement head
PublicationFiber-optic sensors find numerous applications in science and industry, but their full potential is limited because of the risk of damaging the measurement head, in particular, due to the vulnerability of unprotected tips of the fiber to mechanical damage and aggressive chemical agents. In this paper, we report the first use of a new nanocrystalline diamond structure in a fiber-optic measurement head as a protective coating of...
-
Eine Eeue Technik zur Präzisen Rissfortschrittsmessung im DCB oder im Keilversuch = A novel technique for precise crack length measurement in the DCB or wedge test
PublicationDiverse methods have been tried to study crack length, most basic relying on direct, or microscopic, observation of the crack tip position. Optical correlation, both lasermoiré and speckle interferometry, a single strain gauge and displacement sensorshave also been employed. Crack length measurement is, however, delicate. We present a novel method making use of strain gauges attached to one of the adherends.
-
Serotonergic–Muscarinic Interaction within the Prefrontal Cortex as a Novel Target to Reverse Schizophrenia-Related Cognitive Symptoms
PublicationRecent studies revealed that the activation of serotonergic 5-HT1A and muscarinic M1, M4, or M5 receptors prevent MK-801-induced cognitive impairments in animal models. In the present study, the effectiveness of the simultaneous activation of 5-HT1A and muscarinic receptors at preventing MK-801-induced cognitive deficits in novel object recognition (NOR) or Y-maze tests was investigated. Activators of 5-HT1A (F15599), M1 (VU0357017),...
-
The impact of domestic and foreign competition on sectoral growth: a cross-country analysis
PublicationThis paper examines the impact of competition on the total factor productivity (TFP) of 21 manufacturing sectors in eighteen OECD countries over the period of time 1990–2006. We assume that the source of TFP growth can be either domestic or foreign innovation or technology transfer from the technological frontier. Trade openness, R&D, and human capital can have two effects: a direct effect on TFP (e.g., through innovation) and...
-
Transdermal transport of collagen and hyaluronic acid using water in oil microemulsion
PublicationCollagen and hyaluronic acid (HA) are biopolymers that affect the appearance and condition of the skin. Delivery of these compounds into the skin is highly challenging since have a number of disadvantageous properties, such as high molecular weight and hydrophilicity. Here, we evaluated the transdermal penetration of low and high molecular weight collagen and HA from microemulsions. A number of microemulsion formulations, differing...
-
Scanning electrochemical micrographs of poly(lactic acid) 3D printed electrodes ablated by femtosecond laser
Open Research DataThe dataset contains the scanning electrochemical micrographs of the femtosecond laser (FSL) ablation at the surface of commercially available carbon black-filled poly(lactic acid) 3D printed electrode. The process is used for the increase of the charge transfer of this electrode in electrochemical studies.
-
Networks Externalities as Social Phenomenon in the Process ICT Diffusion.
PublicationThis paper is designed to fill the gap in knowledge that we have identified regarding the process of diffusion of information and communication technologies and emerging network effects that significantly enhance spread of these technologies. We contribute to the present state of the art by examining the process of ICT diffusion in 50 countries, which in 2015 achieved highest ICT penetration rates.
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublicationThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
Assessment of organic coating degradation via local impedance imaging
PublicationThe paper presents a new approach to organic coating condition evaluation at micrometer scale using localized impedance measurements. It is based on atomic force microscopy (AFM) in contact mode. Impedance is measured between conductive AFM tip and metal substrate covered with organic coating. A single-frequency voltage perturbation signal is applied between the electrodes and current response signal is registered. As the tip is...
-
The analysis of soil resistance during screw displacement pile installation
PublicationThe analysis of soil resistances during screw displacement pile installation based on model and field tests. The investigations were carried out as a part of research project, financed by the Polish Ministry of Science and Higher Education. A proposal of empirical method for prediction of rotation resistance (torque) during screw auger penetration in non-cohesive subsoil based on CPT result.
-
Optical properties of thin TiO2 film deposited on the fiber optic sensor head
PublicationThe presented study was focused on investigation of the titanium dioxide (TiO2) thin film deposited on the fiber tip. The intention of this investigation was using TiO2 film in the construction of the optical fiber sensor head. In the demonstrated construction TiO2 thin layer was deposited on the tip of a commonly used telecommunication single mode optical fiber (SMF-28) by means of the Atomic Layer Deposition (ALD). Thickness...
-
PHYSICAL MODELLING OF GEOTECHNICAL STRUCTURES IN PORTS AND OFFSHORE
PublicationThe physical modelling of subsoil behaviour and soil-structure interaction is essential for the proper design of offshore structures and port infrastructure. A brief introduction to such modelling of geoengineering problems is presented and some methods and experimental devices are described. The relationships between modelling scales are given. Some examples of penetration testing results in centrifuge and calibration chamber...
-
SiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B37/#A35
Open Research DataWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
TiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A39/#B41
Open Research DataWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
SiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A35/#B37
Open Research DataWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 3 min.Secimen...
-
A Method for Underwater Wireless Data Transmission in a Hydroacoustic Channel under NLOS Conditions
PublicationWireless data transmission in the hydroacoustic channel under non-line-of-sight (NLOS) propagation conditions, for example, during a wreck penetration, is difficult to implement reliably. This is mostly due to the multipath propagation, which causes a reduction in the quality of data reception. Therefore, in this work an attempt has been made to develop a reliable method of wireless underwater communication test it under the NLOS...
-
Alternative Energy: Photovoltaic Solar Cells
PublicationSolar radiation is a fuel for photovoltaic cells and modules, which are a source of electric energy. Viable solar technologies that have been developed in the past are starting to be adopted on a broader and more meaningful global scale across different sectors with ever-increasing market penetration. In this entry, a brief overview of the material properties relevant to solar cell operation, the structure of the solar cell, and electrical...
-
Evolution of electrohydrodynamic flow of sduspended particles in a needle-to-plate negative DC corona discharge in air
PublicationCorona discharges are used for collecting dust in electrostatic precipitators (ESPs). The dust collection is mainlyrealized by the electric forces which move the ionized dust particles to the collecting electrodes. However, the presence of coronadischarge in the space between the charging and collecting electrodes in ESPs causes also the so-called ionic wind which set the gasmolecules and dust...
-
Warstwy funkcjonalne tlenkowych ogniw paliwowych
PublicationIn this paper, results describing current research on solid oxide fuel cells conducted at Gdańsk University of Technology, Faculty of Electronics, Telecommunications and Informatics are presented. The results are related to three kinds of functional layers: a thin cathode layer between the porous cathode layer and the electrolyte to improve the cathode performance, a buffer layer between the electrolyte and the cathode to slow...
-
Measurement system for nonlinear surface spectroscopy by atomic force microscopy for corrosion processes monitoring
PublicationIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is especially useful for heterogeneous...
-
Flow cytometric approach to evaluate the impact of hydro-technical concrete compounds’ release to the freshwater microbiome
PublicationThe aim of this research was to test the potential of applying a flow cytometric procedure to evaluate the impact of concrete compounds’ release to the freshwater microbiome. Cells from the collected samples were stained with a fluorogenic redox indicator dye that measures the redox potential of microbial cells. This novel approach was combined with the assessment of microorganisms’ penetration into the internal structures of concrete...
-
Topical delivery of pharmaceutical and cosmetic macromolecules using microemulsion systems
PublicationMicroemulsions are transparent, thermodynamically stable colloidal systems. Over the recent years, they have been increasingly investigated due to their potential as skin delivery vehicles for a wide range of drug molecules. The nanoscale particle size and the specificity of microemulsion components are the main features determining the skin permeation process. However, in order to effectively cross the skin barrier, the active...
-
Application of the laser diode with central wavelength 975 nm for the therapy of neurofibroma and hemangiomas
PublicationThis paper presents newly developed dermatological laser (with central wavelength 975 nm) for application in therapies requiring deep penetration of tissue, e.g. cutaneous (dermal) neurofibroma (Recklinghausen disease) and hemangiomas. This laser can work either in pulse or continues wave mode. Laser radiation is transmitted toward the application region by optical fiber with a diameter of 0.6 mm. The compact design of the laser...
-
Carbon Dioxide Recovery Skid
PublicationIn the face of tightening climate regulations, the adoption of carbon dioxide recovery systems is inevitable. Modular process skid units have been widely adopted across the industry. The gas-steam power plant skid unit with the carbon dioxide recovery system was described. The proposed skid module consists of the compact cycle with the oxy-combustion and the carbon dioxide capture skid unit producing pure compressed CO2. The compactness...
-
A measurement system for nonlinear surface spectroscopy with an atomic force microscope during corrosion process monitoring
PublicationIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is espe-cially useful for heterogeneous...
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublicationThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
TiN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B48/#A45
Open Research DataWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 12 min....
-
TiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B41/#A39
Open Research DataWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 9 min....
-
CrN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A23/#B22
Open Research DataWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 12 min. The...
-
TiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #B39/#A41
Open Research DataWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The test...
-
SiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #B34/#A33
Open Research DataWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The test...
-
TiN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A45/#B48
Open Research DataWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 12 min....
-
TiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A41/#B39
Open Research DataWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The...
-
CrN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #A25/#B21
Open Research DataWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 9 min....
-
CrN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #B22/#A23
Open Research DataWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 6 min. The test...
-
SiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A33/#B34
Open Research DataWear tests in sliding friction of SiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, SiC over SiC. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The test...
-
Improved performance of LaNi0.6Fe0.4O3 solid oxide fuel cell cathode by application of a thin interface cathode functional layer
PublicationIn this work, novel functional layers were prepared by a low temperature spray pyrolysis method on the oxygen side of the solid oxide cells. Thin layers of Ce0.8Gd0.2O2 and LaNi0.6Fe0.4O3 are prepared between the electrolyte and the porous oxygen electrode. Additionally the influence of the sprayed ceria barrier layer on the zirconia based electrolyte with the new layers is evaluated. Impedance spectroscopy results show improvement...
-
CrN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B21/#A21
Open Research DataWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 25 min....
-
TiN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A45/#A47
Open Research DataWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 20 min. The test...
-
TiN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A45/#B45
Open Research DataWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN. Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 90 min. The test...
-
Reshaping financial systems: The role of ICT in the diffusion of financial innovations – Recent evidence from European countries
PublicationExchange-traded funds (ETFs) are among the fastest-growing types of innovative financial products. The emergence and spread of these instruments have been facilitated by the digital revolution. Information and communication technology (ICT) is profoundly reshaping the global economic landscape, laying solid foundations for unrestricted and unbounded flows of information and knowledge, eliminating information asymmetries, and furthering...
-
Visible light photoactivity of TiO2loaded with monometallic(Au or Pt) and bimetallic (Au/Pt) nanoparticles
PublicationTiO2modified with monometallic (Au or Pt) and bimetallic (Au/Pt) nanoparticles have been preparedusing a water-in-oil microemulsion system (water/AOT/cyclohexane) followed by calcination step. Theeffect of metal ratio, reducing agent type (NaBH4or N2H4), TiO2matrix type (P-25, ST-01, TiO-5, TiO2nano-tubes or TiO2obtained by TIP hydrolysis) as well as calcination temperature (from 350 to 650◦C) weresystematically investigated. Obtained...
-
Numerical investigation on the performance of a small counter-rotating wind turbine
PublicationThe article presents the results of the investigation on the performance of a small counter-rotating wind turbine. The wind turbine has been simulated using Computational Fluid Dynamics methods. Actuator Line Model has been successfully used to represent rotors in the computational domain. A parametric study has been carried out, taking into account changes in the tip speed ratio of the rotors while maintaining a constant distance...
-
Repeated Projectile Impact Tests on Multi-Layered FibrousCementitious Composites
PublicationThis research aims to experimentally evaluate the behaviour of multi-layered fibrous cementitious composites withintermediate Glass Fibre Meshes (GFM) under repeated projectile load. The impact load was subjected through a convexedge projectile needle at a low velocity on cylindrical specimens of three-layered fibrous cementitious composites, whichhave two different steel fibre distributions. In series A mixtures, a constant steel...
-
Evaluation of Praseodymium and Gadolinium Doped Ceria as a Possible Barrier Layer Material for Solid Oxide Cells
PublicationIn this work, nanocrystalline layers based on the Pr, Gd co-doped CeO2 were investigated. For the preparation of thin layers, lowtemperature spray pyrolysis technique was used. Different stoichiometries of the layers were produced for comparison on polished sapphire substrates. The microstructure of the prepared thin layers was studied by scanning electron microscopy (SEM), energydispersive X-ray spectroscopy (EDS) and X-ray diffractometry (XRD)....
-
Rainwater chemistry composition in Bellsund: Sources of elements and deposition discrepancies in the coastal area (SW Spitsbergen, Svalbard)
PublicationDiscrepancies in rainfall chemistry in Bellsund were found to be influenced by the orographic barrier and related to the variability in the inflow of air masses as well as to the distance of sampling sites from the sea and thus the extent of sea spray impact. This study covers measurements of rainfall (P) and air temperature (T), physicochemical parameters (pH, specific electrolytic conductivity (SEC), major ions (Cl , NO3 , SO4...
-
The AFM micrographs of gold nanoparticles on silicon substrate
Open Research DataThe dataset contains the first approach towards AFM topographic imaging of gold nanoparticles synthesized and immobilized on the silicon surface. Measurements were made in the semi-contact mode on the NTEGRA Prima device, manufactured by NT-MDT. Scans were performed with amplitude detection at an operating value of 60% of the free oscillation amplitude....
-
APPLICATION OF VORTEX FLOW MODEL IN PROPELLER-STATOR SYSTEM DESIGN AND ANALYSIS
PublicationThe paper covers basics of the vortex model used for propeller-stator systems. The outline of the design algorithm is given and the results of its application are shown. The designed propeller-stator system was the subject of model tests run at the CTO model basin and cavitation tunnel. Stator’s influence on the delivered power required by the propeller and its revolution rate has been examined by conducting self-propulsion...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Application of gpr method in diagnostics of reinforced concrete structures
PublicationThis paper presents an application of the ground penetration method (GPR) for diagnostics of reinforced concrete structures. In situ measurements were conducted for three civil engineering structures: the ground floor structure, the abutment of the railway viaduct and the concrete well. The dual polarized ground penetrating radar with the antenna operating at a center frequency of 2 GHz was used for GPR surveys. Three different...
-
The Emergence of ETFs in Asia-Pacific
PublicationThe major objective of this book is to contribute to the present state of knowledge by exploring empirical links between the processes of diffusion of financial innovations— exchange-traded funds—and growing deployment of ICT across Asia-Pacific countries, between 2004 and 2017. We examine the evolutionary patterns of ETFs on selected Asia-Pacific stock exchanges and verify the hypothesized relationship between increasing ICT penetration...
-
Three electrode configuration measurements of electrolyte-diffusion barrier-cathode interface
PublicationMeasurements of a system consisting of cathode/doped ceria diffusion barrier/doped zirconia electrolyte were made using two- and three-electrode configuration. Results obtained on a three-electrode measurement configuration were compared with and reflect the results obtained in two-electrode configuration. Three-electrode measurements allowed separating the impact of the symmetrical interface in the investigated system. They also...
-
Microstructure and Electrical Properties of Fe,Cu Substituted (Co,Mn)3O4 Thin Films
PublicationIn this work, thin films (~1000 nm) of a pure MnCo2O4 spinel together with its partially substituted derivatives (MnCo1.6Cu0.2Fe0.2O4, MnCo1.6Cu0.4O4, MnCo1.6Fe0.4O4) were prepared by spray pyrolysis and were evaluated for electrical conductivity. Doping by Cu increases the electrical conductivity, whereas doping by Fe decreases the conductivity. For Cu containing samples, rapid grain growth occurs and these samples develop cracks...
-
INVESTIGATION OF BOTTOM SEDIMENT STRATIFICATION
PublicationThe main goal of this paper is to find a method to assess remotely the type of sediments on the basis of the signal received using the parametric echosounder. The images of the sea bottom sediments taken by a parametric echosounder show the fine structure of the upper layer of the bottom sediments. The depth of penetration depends on the type of sediment, in fact on the attenuation of acoustic wave. In the paper the method of distinguishing...
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublicationThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
-
Properties of Barium Cerate-Zirconate Thin Films
PublicationIn this work, we review several experimental results showing the electrical properties of barium cerate-zirconate thin films and discuss them in view of the possible influence of various factors on their properties. Most of the presented Ba(Ce, Zr, Y)O3 thin films were formed by the pulsed laser deposition (PLD) technique, however thin films prepared using other methods, like RF magnetron sputtering, electron-beam deposition, powder...
-
Pesticide residues levels in honey from apiaries located of Northern Poland
PublicationConcentration levels of 30 pesticide residues were measured in honey samples collected from apiaries in northern part of Poland (Pomerania) using method based on the QuEChERS extraction followed by liquid chromatography-tandem mass spectrometry with electron spray ionization (LC-ESI-MS/MS). In 29% of the samples were found positive for at least some of the target compounds. Concentration of bifenthrin, fenpyroximate, methidathion,...
-
Integration of Fluorescent, NV-Rich Nanodiamond Particles with AFM Cantilevers by Focused Ion Beam for Hybrid Optical and Micromechanical Devices
PublicationIn this paper, a novel fabrication technology of atomic force microscopy (AFM) probes integrating cantilever tips with an NV-rich diamond particle is presented. Nanomanipulation techniques combined with the focused electron beam-induced deposition (FEBID) procedure were applied to position the NV-rich diamond particle on an AFM cantilever tip. Ultrasonic treatment of nanodiamond suspension was applied to reduce the size of diamond...
-
Atomic Force Microscope data post-processing algorithm for higher harmonics imaging
PublicationPrevious works have proved that higher harmonics topography imaging using atomic force microscope (AFM) can significantly enhanced its measurement capabilities. Integrated tools dedicated to most of microscopes allow to visualize the investigated surface only by one selected harmonic. Because of the different characteristics of a sample, scanning tip and the environment, appropriate harmonic selection is time consuming and requires...
-
Photoconversion of carbon dioxide to methane and light hydrocarbons
PublicationFotokonwersja ditlenku węgla do lekkich węglowodorów jest czystym i przyjaznym dla środowiska procesem, pozwalającym na obniżenie emisji CO2 przy jednoczesnym generowaniu paliwa. Badanie efektywności procesu fotokonwersji CO2 prowadzono w obecności promieniowania UV-Vis, pary wodnej oraz fotokatalizatorów Ag-TiO2, Au-TiO2, Ag/Au-TiO2 otrzymanych w mikroemulsji woda/AOT/cykloheksan. Najwyższą aktywność w procesie fotoredukcji...
-
Face Profile View Retrieval Using Time of Flight Camera Image Analysis
PublicationMethod for profile view retrieving of the human face is presented. The depth data from the 3D camera is taken as an input. The preprocessing is, besides of standard filtration, extended by the process of filling of the holes which are present in depth data. The keypoints, defined as the nose tip and the chin are detected in user’s face and tracked. The Kalman filtering is applied to smooth the coordinates of those points which...
-
The Influence of Laser Alloying of Ti13Nb13Zr on Surface Topography and Properties
PublicationThe laser alloying is a continually developing surface treatment because of its significant and specific structuration of a surface. In particular, it is applied for Ti alloys, being now the most essential biomaterials` group for load-bearing implants. The present research was performed on the Ti13Nb13Zr alloy subject to laser modification in order to determine the treatment effects on surface topography and its some mechanical...
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublicationDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Strontium-based nanosized phosphates as anticorrosive fi llers of epoxy and polyurethane coating compositions
PublicationAnticorrosive epoxy and polyurethane coatings were compounded using zinc-free nanosized phosphates of strontium (SP) or strontium and aluminum (SAP). For comparison, a nanosized calcium aluminum ammonium phosphate (CAP) and a microsized zinc phosphate (ZP) were tested. Results of salts spray and cyclic corrosion tests revealed better anticorrosive properties of the SAP-based coatings...
-
Wide-field magnetometry using nitrogen-vacancy color centers with randomly oriented micro-diamonds
PublicationMagnetometry with nitrogen-vacancy (NV) color centers in diamond has gained significant interest among researchers in recent years. Absolute knowledge of the three-dimensional orientation of the magnetic field is necessary for many applications. Conventional magnetometry measurements are usually performed with NV ensembles in a bulk diamond with a thin NV layer or a scanning probe in the form of a diamond tip, which requires a...
-
The low coherence Fabry-Pérot interferometer with diamond and ZnO layers
PublicationThe authors present a fiber-optic Fabry-Pérot interferometer built with the application of diamond and zinc oxide (ZnO) thin layers. Thin ZnO films were deposited on the tip of a standard telecommunication single-mode optical fiber (SMF- 28) while the diamond layer was grown on the plate of silicon substrate. Investigated ZnO layers were fabricated by atomic layer deposition (ALD) and the diamond films were deposited using Microwave...
-
Geotechnical characterization of soft soil deposits in Northern Poland
PublicationThis paper presents a geotechnical characterization of deltaic soft soil deposits in the Vistula Marshlands, northern Poland. It shows the limited applicability of organic soil classifications based on Cone Penetration Tests (CPTU) and Dilatometer Tests (DMT). None of the in-situ-based classifications correctly identifies peat. Analysis of the behaviour of contractive/dilative soil layers according to Robertson's updated classification...
-
Global value chains, wages, employment and labour production in China: A regional approach
PublicationIn this study we analyse the relationship of trade and global value chains (GVCs) to the labour market in 31 Chinese provinces for 25 sectors, by means of a system of structural equations. We firstly distinguish between provincial value chains (PVCs) and interprovincial value chains (PRVCs) in order to outline their distribution and evolution over time. Then, we investigate to what extent participation in GVCs, PVCs and PRVCs –...
-
Wpływ rodzaju zanieczyszczenia powierzchni odlewu ze staliwa LH14 na jakość napoin wykonanych elektrodą otuloną
PublicationNapawanie jest szeroko stosowaną metodą naprawiania powierzchni. Pozwala między innymi na uzupełnienie miejsc, w których uprzednio wystąpiły wżery korozyjne. Techniki napawania wykorzystywane są również do przywracania pierwotnego kształtu zużytych części. W pracy wykonano badania napoin wykonanych elektrodami otulonymi na czołowych powierzchniach cylindrycznych próbek ze staliwa LH14. Proces wykonywano dwoma rodzajami elektrod:...
-
Activated Tungsten Inert Gas Weld Characteristics of P91 Joint for Advanced Ultra Supercritical Power Plant Applications
PublicationActivated Tungsten Inert Gas (A-TIG) welding, a variant of tungsten inert gas (TIG) welding, was used for welding P91. In Generation IV power plants, P91 welds are prone to premature failure due to the presence and formation of brittle phases and creep at high temperatures. When performing A-TIG welding, the flux composition plays a role in the reversal of the Marangoni flow in the weld pool, which ultimately determines the level...
-
Performance Evaluation of Asphalt Binder Modified with Shear Thickening Fluid
PublicationThis paper aims at using a dilatant or shear thickening fluid (STF) [a non-Newtonian fluid consisting of particles of nano-silica suspended in a liquid medium, i.e., ethylene glycol (EG), which acts as a carrier fluid; proportion 40:60] as additive or modifier of bitumen in order to enhance its viscoelastic properties. A commonly-used performance grading (PG) system, storage stability test, and different conventional and rheological...
-
Synthetic strategies in construction of organic low molecular-weight carrier-drug conjugates
PublicationInefficient transportation of polar metabolic inhibitors through cell membranes of eukaryotic and prokaryotic cells precludes their direct use as drug candidates in chemotherapy. One of the possible solutions to this problem is application of the ‘Trojan horse’ strategy, i.e. conjugation of an active substance with a molecular carrier of organic or inorganic nature, facilitating membrane penetration. In this work, the synthetic...
-
Lightweight glass and metal roof structures in the 19th century. Architecture and construction.
PublicationThe 19th century brought new construction possibilities. The usage of metal elements in mesh structures, filled in with glass, resulted in creating entirely new types of objects. They have distinguished themselves in architecture and technical solutions. The envelope structures giving spatial interiors were arising very quickly. They have been enabling large light penetration, triggering them extremely bright. Thus these building...
-
Processing of Ce0.8Gd0.2O2-δ barrier layers for solid oxide cells: The effect of preparation method and thickness on the interdiffusion and electrochemical performance
PublicationCe0.8Gd0.2O1.9 (CGO) barrier layers are required to mitigate the chemical reactions between Sr-containing oxygen electrode materials and Zr-based oxygen ion conductors in high-temperature solid oxide cells. Barrier layers produced by different methods were studied in this work. As a reference, a cell with no barrier layer was measured. The application of the powder-processed barrier layers, considerably increases the performance....
-
Microscale diamond protection for a ZnO coated fiber optic sensor
PublicationFiber optic sensors are widely used in environmental, biological and chemical sensing. Due to the demanding environmental conditions in which they can be used, there is a risk of damaging the sensor measurement head placed in the measuring field. Sensors using nanolayers deposited upon the fiber structure are particularly vulnerable to damage. A thin film placed on the surface of the fiber end-face can be prone to mechanical damage...
-
Destruction of AFM probes during normal operation
Open Research DataThe quality of the images obtained with the use of an atomic force microscope is determined by the state of the blade interacting with the tested material. Image artifacts can be generated by various reasons, such as oxidation, contamination or an error in blade fabrication, but also appear as a result of the repeated scanning process and inevitable...
-
THE ROLE OF THIN FUNCTIONAL LAYERS IN SOLID OXIDE FUEL CELLS
PublicationWidespread commercialization of solid oxide fuel cells requires lowering its cost. It is generally accepted that to lower the cost of solid oxide fuel cells it is necessary to use metal alloys as interconnectors and, consequently, lower its operating temperature to slow down interconnectors degradation. As a result the area specific resistance of the cathodes should be lowered to sustain the performance of the cells. In order to...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublicationThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...