Filtry
wszystkich: 303
wybranych: 300
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: IN SITU TESTS
-
Numerical analysis and in situ tests of the Grot Rowecki Bridge in Warsaw
PublikacjaThe paper presents the FEM analysis of the reconstructed the Grot-Rowecki Bridge over Vistula river in Warsaw. The bridge has seven spans and consists of two independent structures with the longest spans of 120 m. After reconstruction the bridge is over 10 m wider. The numerical, nonlinear analysis has been con-ducted on a global and local FEM models. These models are defined so as they strictly comply with global structural bridge...
-
Dynamics analysis of footbridge mode shapes the s8 expressway on the basis of the results of in situ tests
PublikacjaNon-destructive diagnostics for structure may use dynamic measurements realized during vibrations of a facility induced by dynamic environmental impact, enforced by the use of inductors or impulse impact. Dynamic tests and the analysis were undertaken for a footbridge situated over the expressway S8. The studies in situ allowed for dynamic characteristics to be determined: frequency, shape modes and damping for respective frequency...
-
Establishing Relationships between Parameters of the controlled Compaction Soil by Using Various In-Situ Tests
PublikacjaThe aim of research was evaluating reliable correlations between chosen soil parameters describing state of surface layers of soil. The paper presents site comparative tests based on the light falling weight deflectometer (LFWD), the static plate load tester (VSS), the dynamic probing light tester (DPL) and the bearing ratio tester (CBR in-situ) with relationships between soil state parameters. All featured in-situ...
-
Determination of p-y curves for offshore piles based on in-situ soil investigations
PublikacjaOffshore piles are subjected to complex loads with considerable lateral component. The pile-soil response to lateral loads can be described with the p-y method. For a given depth the load–deflection relationship is built to simulate the surrounding soil stiffness. This state-of-art paper presents a brief discussion of determination methods for the p-y curves using a standard approach based on the soil parameters derived from laboratory...
-
In Situ Verification of Numerical Model of Water Hammer in Slurries
PublikacjaThis paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by...
-
A novel sandwich footbridge - Practical application of laminated composites in bridge design and in situ measurements of static response
PublikacjaA novel sandwich composite footbridge is presented in the paper, as an example of practical application of laminated composites in civil engineering. The in situ static load tests of the footbridge before its acceptation for exploitation are shown and discussed. The results are compared with the corresponding ones from a numerical equivalent single layer model of the sandwich structure created within the framework of finite element...
-
The home-made in situ passive flux sampler for the measurement of monoterpene emission flux: preliminary studies
PublikacjaThe paper presents the construction and metrological characteristics of the home-made in situ passive flux sampler, an analytical tool representing small-scale emission chambers working in situ and passively sampling analytes from the gaseous phase. The sorption element was a cylindrical container made of stainless steel net, packed with a carbon sorbent bed-graphitized charcoal, Carbograph 4 (35/50mesh). The recommended working/exposure...
-
BADANIA KOMPOZYTOWEGO MOSTU DLA PIESZYCH
PublikacjaThe paper presents in situ load testing of the innovative footbridge of FOBRIDGE grant mounted at Gdansk University of Technology. The span of composite sandwich structure (GFRP skins, PET core) and the scope of static and dynamic tests are presented. The selected, representative results of in situ measurements and data obtained from the SHM monitoring system are discussed. Besides the standard testing procedures on the full scale...
-
Geotechnical characterization of soft soil deposits in Northern Poland
PublikacjaThis paper presents a geotechnical characterization of deltaic soft soil deposits in the Vistula Marshlands, northern Poland. It shows the limited applicability of organic soil classifications based on Cone Penetration Tests (CPTU) and Dilatometer Tests (DMT). None of the in-situ-based classifications correctly identifies peat. Analysis of the behaviour of contractive/dilative soil layers according to Robertson's updated classification...
-
Dynamic Response of the Suspended on a Single Cable Footbridge
PublikacjaThe article presents numerical simulations, dynamic in situ load tests and a structural health monitoring (SHM) system installed in a suspended on a single cable footbridge. Numerical simulations performed prior to construction indicated the possibility of structural dynamics problems, finally confirmed in the course of dynamic test loading. In the dynamic load course the bridge deck developed vibrations displaying accelerations...
-
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublikacjaIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
Composite sandwich footbridge - measured dynamic response vs. FEA
PublikacjaThe paper describes a process of in situ dynamic tests of a composite sandwich footbridge before its accepta-tion for exploitation in real traffic conditions. It is only a part of a big research task that includes design, manufacture and introduce practical application of the bridge. The in situ measured natural modes and fre-quencies are compared with numerically determined ones. Finite element analysis is established to estimate...
-
Causes of damage and methods of repairing floor made on polystyrene concrete
PublikacjaThe paper describes damages, tests and repair of the floor made on existing ceiling and expanded polystyrene concrete underlay. The floor was built on a reinforced concrete ceiling with an area of about 1050 m2. Significant damage in the form of cracks, detachments and unevenness was found in the floor. In order to determine the causes of damage, in situ tests and laboratory tests were carried out. It was found that the damage...
-
Przyczyny uszkodzeń i sposób naprawy posadzki ze styrobetonu
PublikacjaW artykule opisano uszkodzenia, badania i sposób naprawy posadzki wykonanej na istniejącym stropie żelbetowym o powierzchni ok. 1050 m2 i podłożu ze styrobetonu. W posadzce stwierdzono znaczne uszkodzenia w postaci zarysowań, odspojeń i nierówności. W celu określenia ich przyczyn wykonano badania in situ oraz badania laboratoryjne. Stwierdzono, że przyczyną powstania uszkodzeń są błędy wykonawcze. Wykonano próbną naprawę uszkodzeń...
-
Mutually polarizable QM/MM model with in situ optimized localized basis functions
PublikacjaWe extend our recently developed quantum-mechanical/molecular mechanics (QM/MM) approach [Dziedzic et al., J. Chem. Phys. 145, 124106 (2016)] to enable in situ optimization of the localized orbitals. The quantum subsystem is described with ONETEP linear-scaling density functional theory and the classical subsystem – with the AMOEBA polarizable force field. The two subsystems interact via multipolar electrostatics and are fully...
-
Permeability of sandy soils estimated from particle size distribution and field measurements
PublikacjaAccurate estimation of soil permeability is crucial in many geotechnical applications. Empirical and theoretical equations based on soil particle size distribution (PSD) offer a fast and cheap way for preliminary estimation of permeability in granular soils, however the results obtained from various formulas available in the literature often show significant discrepancies. While several comparative studies on this topic have been...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Non-Destructive Testing of the Longest Span Soil-Steel Bridge in Europe—Field Measurements and FEM Calculations
PublikacjaThe article describes interdisciplinary and comprehensive non-destructive diagnostic tests of final bridge inspection and acceptance proposed for a soil-steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure short-term response was collected. Periodic diagnostics of bridge deformations was done one...
-
Results of the “DPDT-Auger” Research Project on Screw Displacement Piles
PublikacjaThe main objective of the “DPDT-Auger” research project was to test the prototype DPDT auger for forming screw displacement piles in the ground (patented in Poland in 2020). An additional aim was to develop design methods and rules for the making of such piles. The augers and piles were first tested on a model scale, and then more extensively in the real scale on experimental field plots. The results found the overall functionality...
-
Large deformation modelling of CPT probing in soft soil—pore water pressure analysis
PublikacjaThis paper presents the results of finite element modelling with Updated Lagrangian formulation of the Cone Penetration Test in soft soil deposit located in Jazowa, Poland. The numerical calculations are carried out for homogenous, normally consolidated, organic soil layer. The Modified Cam Clay constitutive model for soft soil and Coulomb model for interface are used. The study compares the registered pore water pressure distributions...
-
Instantaneous impedance monitoring of AA 7075 aluminum alloy corrosion in borate buffer with admixed chloride ions
PublikacjaThe study presents a research capabilities of Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a tool used for instantaneous on-line monitoring of corrosion processes on the example of AA 7075 aluminum alloy. A borate buffer with admixed chloride ions in a quantity ranging from 0.05 to 25 mM was used to represent different types of corrosion attack. The surface of samples specimens was evaluated before and after the tests...
-
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
Application of probabilistic tools to extend load test design of bridges prior to opening
PublikacjaLoad tests of bridges are widely performed in a large number of countries. Deterministic comparison of measurement results to the theoretical, FEM (finite element method)-based outcomes with possible further calibration is mostly applied. Sometimes, the data collected in the tests are also used to calibrate the reliability factors of bridge structures or their components. This work proposes to complement the stage of the load test...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublikacjaThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
Effect of interlayer bonding quality of asphalt layers on pavement performance
PublikacjaThe quality of interlayer bonding at the interfaces between the asphalt layers in flexible pavements affects the overall pavement performance. Lack or partial lack of interlayer bonding between asphalt layers can cause pavement's premature failures such as rutting, slippage of the wearing course, cracking or simply a reduction in the calculated fatigue life of the pavement structure. This paper shows the case studies of investigation...
-
Determination of Thermophysical Parameters Involved in The Numerical Model to Predict the Temperature Field of Cast-In-Place Concrete Bridge Deck
PublikacjaThe paper dealswith a concept of a practical computationmethod to simulate the temperature distribution in an extradosed bridge deck. The main goal of the study is to develop a feasible model of hardening of concrete consistent with in-situ measurement capabilities. The presented investigations include laboratory tests of high performance concrete, measurements of temperature evolution in the bridge deck and above all, numerical...
-
Diagnostics and monitoring of the longest span extradosed bridge in Europe
PublikacjaThe article presents complex diagnostic procedures applied for the purpose of behavior analysis of the extradosed bridge with the longest span in Europe that was built in 2018 in Poland. The system of health monitoring was used to: register internal forces in temporary supports, monitor concrete bonding, perform in situ diagnostics and operation tests. The bridge is a continuous four-span structure with spans theoretical lengths...
-
Multimedia services applied to noise and hearing monitoring and measuring
PublikacjaThe goal of this chapter is to show a research study related to processing of data acquired by the multimedia services engineered at the multimedia systems department (MSD) of the Gdansk University of Technology. This concerns a survey on noise threat employing the multimedia noise monitoring system (MNMS) and hearing tests performed by the "I can hear. . . " system. The obtained results of the noise measurements revealed that...
-
Dynamics of the small-span railway bridge under moving loads
PublikacjaThe paper presents the results of dynamic analysis of the small-span railway bridge, subjected to an action of moving trains. Numerical simulations were performed using three different load models: series of moving forces, series of moving single-mass and double-mass oscillators. The parameters of the vehicle were taken from the existing EN57 train. The parameters of the bridge were taken from the existing steel span of 10,24 m...
-
Sulfate‐reducing bacteria‐assisted hydrogen‐induced stress cracking of 2205 duplex stainless steels
PublikacjaThe paper presents the results of a laboratory investigation of the microbiologically assisted hydrogen‐induced stress cracking (HISC) of 2,205 duplex stainless steel (DSS). The testing of susceptibility toward HISC was performed with two different methods. Precharged in sulfate‐reducing bacteria (SRB), inoculated medium samples were subjected to slow strain‐rate testing in artificial seawater. In situ constant load tests were...
-
Investigations On Water Circulation in Animal Sea-Water Basins – On the Example of Seals′ Breeding Pools
PublikacjaThis paper presents general comments concerning investigations on water circulation in animal breeding pools containing sea water. As an example are given results of computer simulation of water circulation in seals’ breeding pools situated in Marine Station at Hel, belonging to Oceanographic Institute, Gdansk University. A mathematical model of three main pools was prepared with taking into account their inflow and outflow water...
-
Influence of Soft Soil Samples Quality on the Compressibility and Undrained Shear Strength – Seven Lessons Learned From the Vistula Marshlands
PublikacjaThis technical article presents the influence of sample quality on the compressibility parameters and undrained shear strength ( c u ) of soft soils from the Vistula Marshlands. The analysis covers: (1) quality of soft soil according to three criteria: void ratio (Δ e / e 0 index), volumetric strain (Δ ɛ v ) and C r / C c ratio; (2) influence of storage time on quality; (3) influence of sample quality on undrained shear strength...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublikacjaThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
Stan awaryjny wiaduktu kolejowego w Bydgoszczy
PublikacjaW pracy przedstawiono opis stanu awaryjnego wiaduktu kolejowego. Omówiono wyniki badań in situ oraz teoretycznych analiz statyczno-wytrzymałościowych ponad 100-letniego obiektu. Przedstawiono wnioski i zalecenia dotyczące doraźnego zabezpieczenia obiektu oraz warunki jego dalszej eksploatacji.
-
Stan awaryjny wiaduktu kolejowego w Bydgoszczy
PublikacjaW pracy przedstawiono opis stanu awaryjnego wiaduktu kolejowego. Omówiono wyniki badań in situ oraz teoretycznych analiz statyczno-wytrzymałościowych ponad 100-letniego obiektu. Przedstawiono wnioski i zalecenia dotyczące doraźnego zabezpieczenia obiektu oraz warunki jego dalszej eksploatacji.
-
Diagnosis of Damage in a Steel Tank with Self-Supported Roof through Numerical Analysis
PublikacjaThe safety of civil engineering structures is one of the most important issues of building industry. That is why the assessment of the damage-involved structural response has recently become of major concern to engineers. Among a number of different approaches to diagnosis of damage, the method of measuring the changes in natural frequencies is considered to be one of the most effective indicators of global damage. From the practical...
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublikacjaIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublikacjaThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
Shear resistance of low height precast concrete lintels
PublikacjaThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Laboratory investigation with subbottom parametric echosounder SES-2000 standard with an emphasis on reflected pure signals analysis
PublikacjaThe main goal of the paper is to describe correlations between measurements results of trials taken on Gulf of Gdańsk bottom sounded with parametric echosounder SES-2000 Standard and laboratory research where collected during survey sediments were measured. Stationary tests took place at Gdansk University of Technology where 30 meters long 1.8 meter deep and 3 meters wide water tank is located. Main lobe of antenna was directed...
-
TB11 test for short w-beam road barrier
PublikacjaFEM (Finite Element Method) is well-suited and widely used tool for simulating a range of phenomena: from these with simple and static behaviour, up to those complicated, highly nonlinear and involving many contacts. In present paper we use one of the advantages of FEM: parametric study could be easily performed and is more economical than series of in-situ tests. If recommended practices is carefully followed, results obtained...
-
Microbial and chemical quality assessment of the small rivers entering the South Baltic. Part II: Case study on the watercourses in the Puck Bay catchment area
PublikacjaDue to its location, Puck Bay is an area particularly vulnerable to pollution of anthropogenic origin. The aim of the study was to assess the water quality of small watercourses entering the inner part of Puck Bay. The paper presents the results of chemical and microbiological analyses of 10 rivers and canals at their estuaries located on the western shore of the internal Puck Bay. The following environmental parameters were analyzed:...
-
Improving the procedure of probabilistic load testing design of typical bridges based on structural response similarities
PublikacjaThis paper concerns load testing of typical bridge structures performed prior to operation. In-situ tests of a two-span post-tensioned bridge loaded with three vehicles of 38-ton mass each formed the input of this study. On the basis of the results of these measurements, an advanced FEM model of the structure was developed for which the sensitivity analysis was performed for chosen uncertainty sources. Three uncorrelated random...
-
Physical modeling in sands in a wide range of stress level: Application to the calibration of CPTU i DMT tests.
PublikacjaPraca dotyczy badań modelowych w gruntach niespoistych ze szczególnym uwzględnieniem wpływu wysokiego poziomu naprężenia na zachowanie się podłoża gruntowego. Praca składa się z siedmiu rozdziałów. W pierwszym z nich opisano zachowanie się piasku w szerokim zakresie naprężeń z uwzględnieniem ściśliwości, kruszenia się ziaren, nieliniowości obwiedni zniszczenia oraz nieliniowości modułu odkształcenia związanych z poziomem naprężenia...
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublikacjaW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
The application of non-destructive methods in the diagnostics of the approach pavement at the bridges
PublikacjaThe article presents the possibility of using non-destructive methods of road pavement diagnostics as an alternative to traditional means to assess the reasons for premature cracks adjacent to bridge objects. Two scanning methods were used: laser scanning to measure geometric surface deformation and ground penetrating radar (GPR) inspection to assess the road pavement condition. With the use of a laser scanner, an effective tool...
-
Exsolution of Ni nanoparticles on the surface of cerium and nickel co-doped lanthanum strontium titanate as a new anodic layer for DIR-SOFC. Anti-coking potential and H2S poisoning resistance of the prepared material
PublikacjaThe aim of this study was to evaluate a new catalytic material for biogas fueled DIR-SOFC. This material was a perovskite-type SrTiO3 doped with La, Ce and Ni of a general formula La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-σ (LSCNT). Additional preparation steps were undertaken to promote a nickel exsolution process. Heat post-treatment of powders in a humidified H2 resulted in an intensive growth of nickel nanoparticles (NPs) while the temperature...
-
Nondestructive methods complemented by FEM calculations in diagnostics of cracks in bridge approach pavement
PublikacjaNondestructive methods of road pavement diagnostics are an alternative to traditional approach to pavement failure investigation. The article presents a detailed multidisciplinary inspection carried out using ground-penetrating radar (GPR), laser scanning technology and finite element method (FEM) calculations. It was done in order to assess the factors that contributed to occurrence of premature cracks of a bridge approach pavement....
-
Eksperymentalna weryfikacja procedury szacowania wytrzymałości młodego betonu wg normy ASTM C1074
PublikacjaW referacie przedstawiono metodę służącą oszacowaniu wytrzymałości betonu w trakcie procesu dojrzewania (ang. Maturity Method) bazującą na procedurze określonej zgodnie z amerykańską normą, która uwzględnia wpływ połączonych efektów temperatury i czasu na rozwój wytrzymałości betonu. Standardy ASTM C1074 zostały opracowane przez NBS (ang. National Bureau of Standards) z uwagi na powtarzające się wypadki na palcu budowy wynikające...
-
In-situ and ex-situ resistance measurements of polypyrrole film using double-band electrode
PublikacjaMany in-situ techniques are performed in order to determine the resistance of conducting polymer film. However, the resistance measured in solution can be the combination of polymer resistance and that of other components, such as resistance of supporting electrolyte. Therefore, in this work, the influence of the solution on the resistance of polypyrrole (PPy) film has been studied. PPy film was electrchemically synthesized onto...
-
Badania i analizy kolejowych konstrukcji odciążających typu mostowego
PublikacjaW pracy przedstawiono i omówiono wybrane modele obliczeniowe, wyniki analiz teoretycznych oraz badań trzech typów kolejowych konstrukcji odciążających typu mostowego. Zaprezentowano modele obliczeniowe oraz metodykę badań in situ tego typu konbstrukcji. Przedstawiono wnioski dotyczące zaawansowanych metod obliczeniowych rozszerzonych badań in situ w celu diagnozowania rzeczywistej pracy obiektów mostowych.
-
BADANIA ODBIOROWE ŁUKOWEJ KŁADKI DLA PIESZYCH 10T NAD DROGĄ S8 W WARSZAWIE
PublikacjaThe paper presents in situ load testing of the newly build footbridge over S8 expressway in Warsaw. The most characteristic thing for the structure is a shape of arch girders, which correspond with adjacent half-tunnel acoustic baffles. The paper consists of description of the structure, results of the in-situ static and dynamic load testing, results of the numerical simulations, comparative analysis and final conclusions on the...
-
RAMAN DIAGNOSTICS OF CVD DIAMOND GROWTH
PublikacjaDevelopment of Raman spectroscopic system for diagnostics of growth of diamond and BDD (Boron- Doped-Diamond) thin films during μPA CVD (Microwave Plasma Assisted Chemical Vapour Deposition) process is described. Raman studies of such films were carried out as in-situ monitoring of film deposition as ex-situ measurements conducted for a sample outside the reaction vessel after manufacturing process. Modular system for the in-situ...
-
Małe mosty kolejowe z płytą ortotropową
PublikacjaW pracy przedstawiono wyniki badań i analiz obliczeniowych mostów kolejowych małych rozpiętości z pomostami w formie płyty ortotropowej. Przedstawiono sposoby modelowania tych konstrukcji. Podano zakres i metodykę prowadzonych badań in situ. Wyniki analiz teoretycznych porównano z wynikami badań. Przedstawiono wnioski dotyczące sposobów modelowania tego typu konstrukcji i konieczności badań in situ oraz stosowania zaawansowanych...
-
Mosty kolejowe małych rozpiętości - obliczenia i badania
PublikacjaW pracy przedstawiono wyniki badań i analiz obliczeniowych mostów kolejowych ma-łych rozpiętości. Przedstawiono sposoby modelowania w celu wiernego odzwierciedlenia rzeczywistej pracy konstrukcji. Podano zakres i metodykę prowadzonych badań in situ. Wy-niki analiz teoretycznych porównano z wynikami badań. Przedstawiono wnioski dotyczące sposobów modelowania tego typu konstrukcji i konieczności badań in situ oraz stosowania zaawansowanych...
-
Monitoring ramanowski wzrostu cienkich warstw węglowych-studium
PublikacjaPrzedstawiono zagadnienia monitorowania in-situ prózniowego procesu wzrostu cienkich warstw węglowych, a w szczególności diamentowych i diamentopodobnych DLC. Zastosowanie pomiarów ramanowskich umożliwia zbadanie struktury warstwy na poziomie molekularnych (zawartości faz węglowych sp2 i sp3, a także defektów wodorowych). Użycie spektroskopii in-situ podczas procesu syntezy pozwala monotorować poprawność przebiegu procesu i opracować...
-
In-situ optical diagnostics of boron-doped diamond films growth
PublikacjaInterferometry is a desirable method for in-situ measurement of thin, dielectric film growth, as it don't modify conditions of film deposition. Here we present interferometrical measurements of thickness of doped diamond films during Chemical Vapor Deposition (CVD) process. For this purpose we used a semiconductor laser with a 405nm wavelength. Additional ex-situ measurement using spectral interferometry and ellipsometry...
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublikacjaThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
Polymer Modified Bitumen
PublikacjaIn this paper we present the benefits of using polymers as an asphalt modifiers, especially the low molecular weight reactive compounds, which are capable of forming an polymer network with bitumen "in situ" in the process of its modification.
-
A XAS study of a highly diluted Pt electrocatalyst operating in PEM fuel cells
PublikacjaWe present an X-ray absorption spectroscopy (XAS) study of a low Pt content catalyst layer(Pt loading 0.1 mg c2) operating at the cathode of a proton exchange membrane fuel cell(PEMFC). This catalyst is based on the use of a mesoporous inorganic matrix as a support forthe catalyst Pt nanoparticles. Due to the high Pt dilution, in situ measurements of itsstructural properties by XAS are challenging and suitable experimental strategies...
-
Aspekty geotechniczne w projektowaniu infrastruktury komunalnej
PublikacjaZnaczenie badań geotechnicznych na etapie projektowania i realizacji. Kategorie, zakres badań. Badania in situ. Projektowanie geotechniczne. Programowanie badań. Wybór parametrów. Geotechnika metod bezwykopowych. Stateczność skarp. Projektowanie odwodnień wykopów
-
ARCHED VIADUCT OVER PKP TRACKTS IN TCZEW
PublikacjaPraca stanowi streszczenie artykułu dotyczącego nietypowego wiaduktu łukowego z jednym dźwigarem głównym. Omówiono konstrukcję, technologię wznoszenia modele obliczeniowe,analizy teoretyczne oraz metodykę i wyniki przeprowadzonych badań in situ obiektu.
-
Identyfikacja parametrów dynamicznych want mostu Rędzińskiego we Wrocławiu
Publikacjathe paper presents results of dynamic analysis conducted on stay-cables of rędziński bridge in wrocław. identified in situ dynamic parameters (natural frequency and logarithmic decrement damping ratio) of selected stays were and compared to the values featured in the project.
-
Detection of sulfonamide resistance genes via in situ PCR-FISH
PublikacjaDue to the rising use of antibiotics and as a consequence of their concentration in the environment an increasing number of antibiotic resistant bacteria is observed. The phenomenon has a hazardous impact on human and animal life. Sulfamethoxazole is one of the sulfonamides commonly detected in surface waters and soil. The aim of the study was to detect sulfamethoxazole resistance genes in activated sludge biocenosis by use of...
-
Właściwości modyfikowanych emulgatorów acyloglicerolowych syntetyzowanych z mieszanin kwasów tłuszczowych.
PublikacjaPrzedstawiono właściwości modyfikowanych emulgatorów acyloglicerolowych, estrów glicerolu i kwasów tłuszczowych, które są otrzymywane w warunkach przemysłowych. Emulgatory syntetyzowano metodą bezpośredniej ekstrakcji w obecności otrzymywanych in situ soli sodu i stosowanych kwasów tłuszczowych.
-
Genotoxic properties of glucosinolates and isothiocyanates present in Brassica vegetables
PublikacjaThe bioactive phytochemicals found in Brassica vegetables, in this number glucosinolates (GLS), as well as products of their degradation such as isothiocyanates (ITC) and indoles, are regarded as the most promising chemopreventive compounds. These secondary metabolites display stron antibiological activity and constitute defence system preventing the development of agrophages attacking Brassica plants. Such properties suggest...
-
Role of reciprocating sliding testing in tribological materials engineering
PublikacjaPrzedstawiono wyniki badań oporu ruchu i zużycia skojarzeń o styku rozłożonym przy posuwisto-zwrotnym ślizganiu. Badano skojarzenia: żeliwo-stop aluminium przetapiany laserowo w warunkach kriogenicznych oraz żeliwo-kompozyt aluminium-żelazo otrzymany ''in situ''.
-
Laser reflectance interferometry system with a 405 nm laser diode for in-situ measurement of CVD diamond thickness
PublikacjaIn situ monitoring of the thickness of thin diamond films during technological processes is important because it allows better control of deposition time and deeper understanding of deposition kinetics. One of the widely used techniques is laser reflectance interferometry (LRI) which enables non-contact measurement during CVD deposition. The authors have built a novel LRI system with a 405 nm laser diode which achieves better...
-
Combined chemoresistive and in situ FTIR spectroscopy study of nanoporous NiO films for light-activated nitrogen dioxide and acetone gas sensing
PublikacjaThe chemoresistive sensor response of nanoporous NiO films prepared by advanced gas deposition was investigated by combined resistivity and in situ FTIR spectroscopy, with and without simultaneous light illumination, to detect NO2 and acetone gases. The sensitivity towards NO2 increased dramatically under UV irradiation employing 275 nm light. Improved sensitivity was observed at an elevated temperature of 150 °C. In situ FTIR...
-
O badaniach i analizach mostów tymczasowych typu Bailey - MS 22-80
PublikacjaPrzedstawiono sposoby modelowania oraz wyniki badań in situ konstrukcji mostów tymczasowych typu Bailey - MS 22-80. Sformuowano wnioski dotyczące rzeczywistego zachowania się tego rodzaju konstrukcji oraz zasad modelowania w celu jednoznacznego określenia pracy i wytężenia ustroju.
-
Problems and challenges associated with estimating the emissions of organic compounds from indoor materials
PublikacjaFor several years intensive research has been carried out with the aim of developing a database of the types and amounts of pollutants released from indoor materials to the indoor environment. The paper discusses in detail basic problems and challenges encountered when estimating the emissions of chemical compounds released from of indoor materials. Factors affecting the validity of data obtained by using two different types of...
-
Influence of sodium dodecyl sulfate presence on esterification of propylene glycol with lauric acid
PublikacjaZbadano wpływ obecności dodecylosiarczanu sodu na bezpośrednią estryfikację glikolu propylenowego kwasem laurynowym. Zbadano także rozkład wielkości cząstek mikroemulsji tworzącej się in situ w trakcie estryfikacji glikolu propylenowego kwasem laurynowym w obecności różnych stężeń dodecylosiarczanu. Oceniono wartość równowagi hydrofilowo - lipofilowej zsyntetyzowanych emulgatorów.
-
Ocena uciążliwości zapachowej powietrza atmosferycznego na obszarach przyległych do oczyszczalni ścieków komunalnych z zastosowaniem olfaktometrii terenowej
PublikacjaWykorzystano technikę olfaktometrii terenowej do oceny jakości powietrza atmosferycznego na obszarach przyległych do oczyszczalni ścieków komunalnych. Zastosowanie techniki olfaktometrii terenowej umożliwiło pomiar emisji odorów in-situ, wskazanie miejsc charakteryzujących się największą uciążliwością zapachową oraz określenie stężenia zapachowego w poszczególnych punktach pomiarowych.
-
In-Situ Processing of Biocomposites via Reactive Extrusion
PublikacjaLaw regulations, economic and environmental factors are the main causes for the rapidly growing interests in biocomposites’ research, conducted currently in a number of academic and industrial scientific centers. However, weak polymer matrix/filler interactions, common in biocomposites, result in unsatisfactory mechanical properties, which limit their practical applications. From many attempts performed to solve this problem, in-situ...
-
Systematic Water Uptake Energetics of Yttrium-Doped Barium Zirconate—A High Resolution Thermochemical Study
PublikacjaA combination of surface area analyzer and microcalorimetry was employed to investigate the in situ water uptake energetics and the mechanism of proton incorporation in yttrium-doped barium zirconate in the temperature range 200–400 °C. The BaZr1–xYxO3 solid solutions are made with variable yttrium content (x = 10, 20, and 30 mol %) by a controlled oxidant-peroxo synthesis method. The water uptake increases as the partial pressure...
-
Towards spectroscopic monitoring of photoelectrodes: In-situ Raman photoelectrochemistry of a TiO2/prussian blue photoanode
PublikacjaHere, novel in-situ Raman photoelectrochemical measurements are performed. The obtained results have proved that it is possible to track the progress of a photoelectrochemical reaction that takes place on a semiconducting electrode using the spectroscopic method. As an exemplary system, the Ti/TiO2/Prussian blue electrode is investigated. Since TiO2 is an n-type semiconductor, it cannot act as an efficient anode in dark conditions....
-
Assessment of tensile forces in Sopot Forest Opera membrane by in situ measurements and iterative numerical strategy for inverse problem
PublikacjaAssessment of tensile forces in newly build Sopot Forest Opera roofing membrane is presented. The procedure is based on in situ measurements and solution of the inverse problem by an iterative procedure. The goal of the analysis is to determine whether the stress state of the membrane is consistent with the design assumptions. The paper contains the description of measurements, used instruments, applied loadings, numerical investiga-tions...
-
Monitoring ramanowski wzrostu cienkich warstw węglowych-studium
PublikacjaPrzedstawiono wybrane problemy diagnostyki ramanowskiej in-situ wzrostu cienkich warstw węglowych w prózniowym procesie CVD, w szczególności problemy doboru długości fali lasera oraz konstrucji głowic optycznych. Opisano system pomiarowy zrealizowany w Katedrze Optoelektroniki i Systemów Elektronicznych PG. Przedstawiono wyniki wstępnych pomiarów oraz ich interpretację.
-
Analiza procesu zniszczenia kompozytu warstwowego aramidowo-szklanego przy zginaniu metodą in situ
PublikacjaPrzeprowadzono badania na zginanie in situ w komorze mikroskopu SEM kompozytów: winyloestrowego zbrojonego tkaniną aramidową i szklaną oraz epoksydowego zbrojonego hybrydową tkaniną aramidowo-szklaną. Otrzymano sekwencję obrazów postępującego zniszczenia laminatów. Określono przyczynę małej wytrzymałości laminatu winyloestrowego w porównaniu z laminatem epoksydowym o zadowalającej wytrzymałości.
-
Local Ordering Changes in Pt-Co Nanocatalyst Induced by Fuel Cell Working Conditions
PublikacjaPraca poświęcona jest szczegółowej analizie zmian w lokalnej strukturze atomowej i elektronowej nanocząstek Pt-Co pracujących jako katalizatory w polimerowych ogniwach paliwowych wywołanych cyklicznie zmieniającymi się warunkami pracy ogniwa. Do analizy wykorzystano badania XAS realizowane ex-situ i in-situ, XRD i TEM. Analizując widma XAFS wzięto pod uwagę możliwy wpływ nieporządku chemicznego oraz redukcję liczb koordynacyjnych...
-
Destabilizacja układów emulsyjnych powstających podczas oczyszczania gruntów
PublikacjaCelem pracy było zbadanie efektywności destabilizacji układów emulsyjnych tworzących się podczas przemywania zanieczyszczeń olejowych z gruntów w warunkach ex-situ, za pomocą roztworów surfaktantu Rokanolu NL6. Jako zanieczyszczenie hydrofobowe wybrano syntetyczny olej bazowy typu polialfaolefin (PAO6). Zastosowano pięć metod destabilizacyjnych: odstawianie, wirowanie, wygrzewanie, wymrażanie, zmiana pH.
-
Styrene epoxidation over heterogeneous manganese(III) complexes
PublikacjaThe manganes(III) complex functionalised with 2,3-dihydropyridazine has been encapsulated in the supercages of the NaY zeolite using two different procedures, flexible ligand and in situ complex. The parent zeolite and the encapsulated manganese(III) complexes were screened as catalysts for styrene oxidation by using t-BOOH as the oxygen source in acetonitrile. Under the optimized conditions, the catalysts exhibited moderate activity...
-
BADANIA ODBIOROWE KOMPOZYTOWEJ KŁADKI NAD KANAŁEM RADUNI W PRUSZCZU GDAŃSKIM
PublikacjaW pracy przedstawiono wyniki badań przeprowadzonych podczas próby obciążeniowej kładki kompozytowej GFRP w Pruszczu Gdańskim. Badania obejmowały zarówno testy statyczne, jak i dynamiczne. Uzyskane wyniki wskazują na większą niż teoretycznie oczekiwaną sztywność przestrzenną konstrukcji. Wszystkie pomierzone parametry struktury były lepsze podczas pomiarów in-situ, niż wykazały analizy numeryczne.
-
Application of nonmetallic frustrated cations in the activation of small molecules
PublikacjaThe concept of nonmetallic frustrated cations has been used in small molecule activation. The in situ generated ambiphilic phosphinoborinium cation activated phenyl isocyanate, diisopropylcarbodiimide, and acetonitrile under very mild conditions without any catalyst, yielding single-, double-, or mixed-activation products. Furthermore, the mechanisms of the reactions of the phosphinoborinium cation with small molecules were elucidated...
-
Wytłaczanie past ceramicznych - optyczny monitoring poślizgu przyściennego
PublikacjaPrzedmiotem niniejszej pracy jest optyczna metoda spektroskopii reflektancyjnej do pomiaru in situ grubości warstwy przyściennej w procesie wytłaczania past ceramicznych, którą można stosować bez zakłócania przebiegu procesu. Może ona znaleźć zastosowanie do dostarczania danych w analizie i modelowaniu procesu wytłaczania, a także do kontroli on-line przebiegu procesu produkcyjnego.
-
Functional properties of packaging materials from chemical modified stach.
PublikacjaThis work is focused on study of the mechanical and barrier properties of films obtained from potato starch modified with sodium tetrahydroxozincate generated in situ. The results show that the chemical modification of starch improved the water vapor permeability by about 25%, unfortunately decreased the elongation at break by 60%, when compared with unmodified starch films. However, placitization of films with glycerol at a concentration...
-
Mikrostruktura kompozytów poliuretanowo-gumowych, otrzymywanych in situ z elastomerów uretanowych i recyklatów gumowych
PublikacjaW pracy przedstawiono wyniki badań dotyczące mikrostruktury nowej grupy kompozytów poliuretanowo-gumowych (KPG). Materiały kompozytowe otrzymano in situ z lanych elastomerów ure-tanowych (LEU) i różnej ilości recyklatu gumowego (RG), uzyskiwanego w wyniku kriogenicznego rozdrabniania poużytkowych opon samochodowych. Mikrostrukturę przełomów KPG zbadano przy wykorzystaniu mikroskopii optycznej (OM) oraz transmisyjnej mikroskopii...
-
STUDY OF SEASONAL ACOUSTIC PROPERTIES OF SEA WATER IN SELECTED WATERS OF THE SOUTHERN BALTIC
PublikacjaClimate Research of the globe is a current task, in particular to confirm the general hypothesis of global warming associated with an increase in average temperature. The sea acoustic climate is derived from the concept of climate and refers to the conditions of propagation of acoustic waves in a particular basin. In this paper, the results of systematic measurements of temperature, salinity and velocity distributions of sound...
-
Ochrona katodowa stali zbrojeniowej w długoletnim okresie eksploatacji
PublikacjaZapobieganie powstawaniu ognisk korozji w zbrojeniu konstrukcji żelbetowych jest jednym z głównych czynników, które pozwalają na długą i niezawodną ich eksploatację. W artykule przedstawiono mechanizm działania protektorów cynkowych na podstawie przeprowadzonych badań in situ. Przedstawione badania wskazują, że ochrona katodowa z wykorzystaniem polskich protektorów cynkowych TOP ZINC wykazuje bardzo sprawne działanie.
-
Badania tribologiczne w warunkach posuwisto-zwrotnego ślizgania skojarzeń: żeliwo-kompozyt aluminiowo-żelazowy.
PublikacjaOpisano badania kompozytów: silumin AlSi11-żelazo albo silumin AlSi11-stal narzędziowa N9 (otrzymanych in situ), a także samego siluminu AlSi11 w skojarzeniu z żeliwem 350, przy tarciu ślizgowym w ruchu posuwisto-zwrotnym. Stwierdzono wpływ sposobu otrzymywania materiału kompozytowego na zużycie i opory ruchu skojarzenia badawczego, w szczególności materiały te zużywały się wolniej, niż silumin AlSi11.
-
A tribological research on a reciprocating sliding contact of aluminum-ferrous composite against cast-iron.
PublikacjaOpisano badania kompozytów: silumin AlSi11-żelazo albo silumin AlSi11-stal narzędziowa N9 (otrzymanych in situ), a także samego siluminu AlSi11 w skojarzeniu z żeliwem 350, przy tarciu ślizgowym w ruchu posuwisto-zwrotnym. Stwierdzono wpływ sposobu otrzymywania materiału kompozytowego na zużycie i opory ruchu skojarzenia badawczego, w szczególności materiały te zużywały się wolniej, niż silumin AlSi11.
-
The shallow sea experiment with usage of linear hydrophone array
PublikacjaPurpose of this article is to present designed and made linear hydrophone array and the results obtained during in situ trails on Gulf of Gdańsk. The measuring system allowed to localize hydrophones in the selected points and perform measurements in both the horizontal antenna positioning and vertical. Made in this way recordings allow creating accurate 3D imaging of sound intensity/propagation. During research three floating objects...
-
Entrained Flow Plasma Gasification of Sewage Sludge–Proof-of-Concept and Fate of Inorganics
PublikacjaSewage sludge is a residue of wastewater processing that is biologically active and consists of water, organic matter, including dead and living pathogens, polycyclic aromatic hydrocarbons, and heavy metals, as well as organic and inorganic pollutants. Landfilling is on the decline, giving way to more environmentally friendly utilisation routes. This paper presents the results of a two-stage gasification–vitrification system, using...
-
Metody wzmacniania podłoża gruntowego dla potrzeb budowy dróg i mostów.
PublikacjaDefinicje metod uzdatniania podłoża gruntowego: ulepszanie gruntu i wzmocnienie gruntu. Zagęszczanie gruntów ziarnistych: mechanizmy zagęszczania, metody zagęszczania: zagęszczanie metodą mikrowybuchów, zagęszczanie dynamiczne, wibroflotacja. Iniekcje: rodzaje i mechanizmy iniekcji, iniektowanie za pomocą nasycania, iniekcja strumieniowa. Metody uzdatniania gruntów spoistych: wstępne obciążenie, wzmocnienie kolumnami balastowymi,...
-
Synthesis of polyglycerol esters of fatty acid with defined hydrophilic properties
PublikacjaOtrzymane w odrębnej reakcji mieszaniny poligliceroli poddano estryfikacji kwasami tłuszczowymi oktadekanowym i izooktadekanowym, w obecności odpowiednich mydeł sodu powstających in situ. Zaobserwowano wpływ stężenia karboksylanów sodu oraz budowy kwasu tłuszczowego na przebieg estryfikacji mieszaniny polioli. Stwierdzono, że zastosowany sposób prowadzenia reakcji pozwala zsyntetyzować efektywne emulgatory emulsji O/W, o wartościach...
-
System optoelektroniczny do kontroli procesów μPA CVD
PublikacjaPrzedstawiono prototyp optoelektronicznego systemu do monitorowania in-situ procesu CVD, wspomaganych plazmą mikrofalową. System składa się z układu optycznej spektroskopii emisyjnej OES oraz specjalizowanego spektroskopu ramanowskiego RS. Umożliwia on równoczesne monitorowanie składu plazmy oraz określanie dynamiki wzrostu i zawartości defektów warstwy. Przedstawiono wyniki badań przebiegu procesu wytwarzania warstw diamentopodobnych...
-
Wspomaganie procesu denitryfikacji substancjami odpadowymi z przemysłu gorzelniczego
PublikacjaW pracy tej oleje fuzlowe, produkt uboczny pozostały z produkcji alkoholu spożywczego w destylarniach i gorzelniach, badano jako alternatywne źródło węgla w stosunku do komercyjnego produktu – etanolu. Z uwagi na fakt, iż węgiel organiczny znacząco wpływa na bakteriocenozę osadu czynnego, struktura mikroorganizmów oraz zróżnicowanie biomasy występującej w rektorach analizowana była za pomocą fluorescencyjnej hybrydyzacji in situ...
-
An efficient and convenient synthesis of unsymmetrical disulfides from thioacetates
PublikacjaWe have developed convenient methods for the synthesis of functionalized unsymmetrical dialkyl disulfides under mild conditions in very good yields. The designed method is based on the reaction of (5,5-dimethyl-2-thioxo-1,3,2-dioxaphosphorinan-2-yl)-disulfanyl derivatives 1 with functionalized alkyl thiolate anions, generated in situ from thioacetates2and sodium methoxide or butylamine. The developed method allows the preparation...
-
Efficient Synthesis of Functionalized Unsymmetrical Dialkyl Trisulfanes
PublikacjaWe have developed a convenient method for the synthesis of functionalized unsymmetrical dialkyl trisulfanes under mild conditions in very good yields. The designed method is based on the reaction of (5,5-dimethyl-2-thioxo-1,3,2-dioxaphosphorinan-2-yl)-disulfanyl derivatives with alkyl disulfanyl anions generated in situ from S-acetyl disulfanyl derivatives and sodium methoxide. The developed method allows for the preparation of...