displaying 1000 best results Help
Search results for: Fuel oil and greases
-
Methodology for determining the elemental composition, as well as energy and ignition properties of the low-sulfur marine fuels
PublicationThe key metrological issue of substance and energy balance in research engines is the precise determination of the elemental composition of the applied fuel and its net calorific value. This makes it possible to calculate the amount of heat brought with the fuel into the combustion chamber, as well as the amount and gas composition of the exhaust. However, to fully assess the energy quality of the fuel used, its ignition properties...
-
The comparison of SrTi0.98Nb0.02O3–δ-CeO2 and SrTi0.98Nb0.02O3–δ-YSZ composites for use in SOFC anodes
PublicationComposites of Nb-doped strontium titanate mixed with yttria-stabilized zirconia or cerium oxide in 50:50, 70:30 and 85:15 weight ratios were evaluated as possible anode/electrolyte interface materials for solid oxide fuel cells in terms of chemical compatibility, electrical conductivity and mechanical properties. It has been shown that composite samples prepared by typical powder-mixing methods remain single-phase up to 1400°C....
-
Cargo ships heat demand - operational experiment
PublicationThe paper presents the results of an experiment conducted on two cargo ships – a 5300 TEU container with a steam heating system and a 7500 dwt general cargo ship with a thermal oil system. On both ships research has been carried out using specially designed measuring equipment. After gathering data about flow velocity and temperatures (steam/ cooling water/ thermal oil/ seawater/ outside air), calculations have been done, resulting...
-
Measurements of the Hydraulic Fluids Compressibility
PublicationPerformance of the hydrostatic high-pressure drive systems is affected by the changes of working fluid’s volume. Presence of air bubbles in the fluid cause this problem to be even more serious. To study this phenomenon precise measurements of fluid’s bulk modulus are necessary. Differ-ent measurement methods are applied, but they are either limited to low pressure range or give inaccurate results. To solve the problem the new...
-
Influence of Wastewater Treatment Technology on Particle Size Distribution in the Effluent
PublicationSuspended solids in water and wastewater usually carry quite a large load of pollutants (organic substances, nutrients, heavy metals, etc.) adsorbed on the particles surface. Particles of different sizes carry different types and quantities of pollutants. Therefore, particle size distribution is of importance in waster and wastewater treatment. In the article the influence of different treatment technologies on particle size distribution...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublicationA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
Polyester-urethanes modified with gelatine for tissue scaffolds
PublicationNovel aliphatic PU foams, modified with gelatine, were obtained in a one-step polymerization process. Hard segments were obtained from 1,6-hexamethylene diisocyanate (HDI) and chain extenders 1,4-butanediol (BDO) or 2-(2-(2-hydroxyethoxy)ethoxy)ethanol (TG), soft segments were obtained from poly(ethylene-buthylene adipate) (EBO) polyol. We examined the PU foams for their sorption capability in canola oil, saline (0.9% NaCl water...
-
Analiza warunków pracy silnika spalinowego lokomotywy na biegu jałowym
PublicationW trakcie eksploatacji lokomotyw z silnikami spalinowymi obserwowany jest znaczny udział pracy silnika spalinowego w stanie biegu jałowego. Dlatego też średnia wartość strumienia paliwa zużywanego przez silnik spalinowy lokomotywy w tym stanie będzie miała istotny wpływ na efektywność energetyczną układu napędowego. Wyznaczaniu wartości tego parametru musi towarzyszyć jednoznaczna klasyfikacja warunków pracy układu napędowego lokomotywy....
-
Określenie zawartości lotnych kwasów tłuszczowych (LKT) w odciekach pochodzących z mikrobiologicznej degradacji monosacharydów
PublicationOkreślenie zawartości lotnych kwasów tłuszczowych (LKT) w odciekach pochodzących z mikrobiologicznej degradacji monosacharydów. Milena Jabłońska, Maria Rybarczyk, Marta Wisielewska, Marek Lieder Politechnika Gdańska, Wydział Chemiczny, Katedra Technologii Chemicznej Zawartość lotnych kwasów tłuszczowych (LKT) w metabolitach pochodzących z mikrobiologicznego ogniwa paliwowego (MFC – Microbial Fuel Cell) świadczy o rozkładzie...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublicationThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublicationDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Poland’s energy dependence - economic context
Open Research DataPoland does not have vast resources of non-renewable energy and no nuclear power plant, therefore the issue of the energy dependence of the state, which affects the level of energy security of the country, is an extremely important factor. It depends on both the volume of imports of energy raw materials and the policy of diversification of sources of...
-
Wetting properties of biosurfactant (rhamnolipid) with synthetic surfactants mixtures in the context of soil remediation
PublicationWetting properties of synthetic surfactant Rokanol NL6, biosurfactant JBR 425 and their mixture have been investigated.The results show that synthetic surfactant addition worsens physicochemical properties of pure biosurfactant but exhibits much higher oil removal efficiency than biosurfactant does.
-
Exergetic Analysis of the nCO2PP Cycle with Particular Reference to the Exergy Destruction of Sewage Sludge Due to Gasification
PublicationAn exergy analysis is carried out on the negative CO2 emission gas power plant (nCO2PP), which integrates the process sections of fuel preparation, power generation and carbon capture. Processes of exergy destruction are studied with particular focus on the process in the gasification unit of the fuel preparation section, where a large amount of exergy is destroyed in various chemical reactions from sewage sludge to producer gas...
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublicationThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
Copper and cobalt co-doped ceria as an anode catalyst for DIR-SOFCs fueled by biogas
PublicationThe nanocrystalline compounds of Co and Cu co-doped ceria (with up to 20 mol.% of dopants) were fabricated by the reverse microemulsion synthesis method. They were deposited in a form of layers on the surface of SOFC anode in an aim to act as electrochemically active materials for biogas reforming process. Fourier Transformed Infrared Spectroscopy was used to analyze a composition of outlet gases simultaneously with the tests of...
-
High temperature corrosion resistance of porous hastelloy alloy
PublicationTo further understand the suitability of Ni-Cr-base alloy for solid oxide fuel cell (SOFC), a commercial Ni-Cr-Fe-Mo alloy, Hastelloy X was selected and evaluated for oxidation behaviour under high temperature conditions. HastelloyX was chosen due to its unusual resistance to oxidizing, reducing and neutral atmospheres. For long term stability of metal supported fuel cell, the corrosion resistance plays a vital role and must be...
-
Zagadnienia tribologiczne w hamulcu silnika hydraulicznego
PublicationPrzedmiotem badań był prototypowy hamulec cierny wielopłytkowy do silnika satelitowego SM-0,6 o teoretycznej objętości roboczej 16,7 cm3/obr. Hamulec ten zbudowany był z 27 tarcz ciernych wykonanych z materiału TOLOX oraz z pakietu sprężyn talerzowych zamontowanych w układzie X. Zablokowanie hamulca następuje w skutek siły docisku pakietu sprężyn talerzowych płytek ciernych co następuje w chwili spadku ciśnienia w komorze tłoka...
-
The influence of inflation pressure and ambient temperature on the value of the truck tires rolling resistance
PublicationThe articlediscusses the effect of inflation pressure and the ambient temperature on the value of the rolling resistance of truck tires which directly translates into fuel consumption. For this purpose, a series of measurements was made at two ambient temperatures (at 25°C and -15°C), using different pumping pressures.
-
Cavitation based cleaner technologies for biodiesel production and processing of hydrocarbon streams: A perspective on key fundamentals, missing process data and economic feasibility – A review
PublicationThe present review emphasizes the role of hydrodynamic cavitation (HC) and acoustic cavitation in clean and green technologies for selected fuels (of hydrocarbon origins such as gasoline, naphtha, diesel, heavy oil, and crude oil) processing applications including biodiesel production. Herein, the role of cavitation reactors, their geometrical parameters, physicochemical properties of liquid media, liquid oxidants, catalyst loading,...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Fruit seeds oils as a cosmetic emulsions component
PublicationThe fruit seeds are known to have a considerable amount of oil and their potential specialty as nutraceutical oil was suggested based on high level of unsaturated triacyglycerols (major fatty acids are linoleic, linolenic, oleic) and a high content of tocols (tocopherols and tocotrienols). In this study the possibility of application fruit seeds oils in W/O and O/W emulsion systems was investigated to find the influence of the...
-
Arylated carbon nanotubes for biobatteries and biofuel cells
PublicationSinglwalled carbon nanotubes (swcnts)covalently phenylated, napthylated or terphenylated were used for the construction of cathodes in a biobattery and in a biofuel cell. zn is the anode in the biobaterry and single-walled carbon nanotubes are covalently modified with glucose oxidase/catalase (swcnt-gox/cat) and the biofuel cell anode. the cell parameters were determined and the potentials of each of the electrodes under cell working...
-
Sliding friction of alumina (Al2O3) with friction induced vibrations
Open Research DataTest files containing data on experiments in self mated sliding contact of alumina Al2O3 lubricated with either water or paraffin oil. Tests run in variable load/velocity conditions and with different dynamic settings of the test rig (PT-3 tribometer). The aim of the research was to attempt in finding correlations between the dynamic characteristics...
-
Novel approach to ecotoxicological risk assessment of sediments cores around the shipwreck by the use of self-organizing maps
PublicationMarine and coastal pollution plays an increasingly important role due to recent severe accidents which drew attention to the consequences of oil spills causing widespread devastation of marine ecosystems. All these problems cannot be solved without conducting environmental studies in the area of possible oil spill and performing chemometric evaluation of the data obtained looking for similar patterns among pollutants and optimize...
-
Utilization of molten salt synthesis route in ceramics production
PublicationThe molten salt synthesis method is widely used to prepare ceramic powders for various applications e.g. piezoelectric devices or electrolytes for solid oxide fuel cells. The usage of this method workdwide is quite common especially in piezoelectric powder synthesis. In this work several application of the method is presented and the advantages of this route are numbered.
-
Effects of CO2 and utilization of spent trickling liquid towards plant growth
Open Research DataDataset presents the results of biomass yield for Phaseolus vulgaris pot cultures watered with diluted trickling liquid from biotrickling filtration experiments with or without additional CO2 in air by means of introducting post-biofilter air to the plant culture.
-
Renewable Resources for Polyurethanes and Polyurethane Composites: A Review
PublicationEach year, more than two million tons of polyurethane is produced in the EU by reacting isocyanates with polyols made from fossil fuel. In addition, there are appreciable quantities of petroleum based functional additives applied in the industry nowadays for both polyols and polyurethane materials. It is therefore of key importance to develop sustainable economically viable polyols with enhanced functionalities, and thereby reducing...
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublicationTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
Optimal shape design of multi-element trawl-doors using local surrogate models
PublicationTrawl-doors have a large influence on the fuel consumption of fishing vessels. Design and optimiza-tion of trawl-doors using computational models are a key factor in minimizing the fuel consump-tion. This paper presents an optimization algorithm for the shape design of trawl-door shapes using computational fluid dynamic (CFD) models. Accurate CFD models are computationally expensive. Therefore, the direct use of traditional optimization...
-
THE IDENTIFICATION OF TOXIC COMPOUND EMISSION SENSITIVITY AS A DIAGNOSTIC PARAMETER DURING DYNAMIC PROCESSES OF THE MARINE ENGINE
PublicationChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure,...
-
Fuctional structure of diagnostic system for wheeled tractors
PublicationAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnosis is strongly connected with emission demands and does not concern other important vehicle functions.In...
-
Deep eutectic solvent (DES) with silver nanoparticles (Ag-NPs) based assay for analysis of lead (II) in edible oils
PublicationThis paper presents an application of silver nanoparticles impregnated by Deep Eutectic Solvents (DES) as ultrasonication aided microextraction system for lead (II) determination in edible oils. The paper presents a systematic optimization of method parameters and examples of its application for analysis of real samples. Maximum recovery for lead (II) extraction was obtained for choline chloride and phenol with a 1:2 molar ratio....
-
POLAND’S ENERGY DEPENDENCE AT THE TURN OF THE 21ST CENTURY
PublicationThe following article is an attempt to assess Poland's energy independence in the years 1993-2020. The main aim of the paper is to present Poland's dependence on raw materials from foreign partners - in the field of imports of electricity, natural gas, crude oil, non-renewable energy resources, i.e., hard coal and lignite, and the country's dynamics in the amount of imports. In addition, the aim of the work is to answer research...
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublicationThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
ЭКОНОМИЧЕСКИЕ КОНТАКТЫ АЗЕРБАЙДЖАНА И ЕВРОПЕЙСКОГО СОЮЗА
PublicationПосле получения независимости в начале 90-х годов XX в. Республика Азербайджан подписала более пятидесяти договоров с международными организациями. В 1991 г. государство установило контакты с Европейским союзом в ходе реализации проектов в рамках программы TACIS, предназначенной для стран СНГ. Экономические контакты между партнерами активизировались, благодаря подписанию и вступлению в силу в 1999 г. Соглашения о партнерстве и...
-
Emulsification alters simulated gastrointestinal proteolysis of β-casein and β-lactoglobulin
PublicationWe have studied the effect of the adsorption of milk proteins at the oil-water interface on their digestibility in simulated gastrointestinal environment. The investigations aimed to characterize how both the breakdown of the adsorbed proteins and the interactions with physiological surfactants, phosphatidylcholine (PC) and bile salts (BS), influence structural transformations of model, protein-stabilized food emulsions in the...
-
Biosurfactants - Biodegradability, toxicity, efficiency in comparison with synthetic surfactants
PublicationBiosurfactants are natural surface active agents produced by variety of bacteria yeast and fungi. A review of their biodegradability, toxicity and efficiency is presented in order to compare their properties with synthetic surfactants. Due to their high efficiency in many applications and environmentally friendly character we tried to apply them in oil refining process. The efficiency of biosurfactants in this application was very...
-
Materiały dla jednowarstwowych ogniw paliwowych
PublicationA composite material, which may be further applied as a single layer fuel cell, was synthesizes using solid state synthesis method. Composite consisted of two components. The first was a nanoeramic proton conductor - calcium doped lanthanum niobate. The second one was a nanoceramic semiconductor oxide composed of lithium, nickel and zinc oxides respectively.
-
MnCo2O4 deposited by spray pyrolysis as a protective layer for stainless steel interconects
PublicationStainless steel interconnects working in Solid Oxide Fuel Cells stacks are exposed to high temperature resulting in their corrosion. Protective layers for the hydrogen and oxygen sides are necessary to protect the interconnect material, prolongate the stack lifetime and maintain the output power. In this paper MnCo2O4 protective layer for the oxygen side of the interconnect is deposited by spray pyrolysis and is examined.
-
The effectivness of fault detection in common rail injectors examination methods
PublicationThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
Structural change of carbon supported Pt nanocatalyst subjected to a step-like potential cycling in PEM FC
PublicationIn this paper we present detailed X-ray absorption fine structure (XAFS), X-ray diffraction (XRD) and transmission electron microscopy (TEM) investigations of the changes in the local geometric and electronic structure of Pt nanoparticles used as a cathode catalyst in proton exchange membrane fuel cell (PEMFC), working under controlled potential cycling conditions.
-
#CiekawiNauki – Olej palmowy w środowisku i żywności
EventsSiódme spotkanie z cyklu #CiekawiNauki. Poznaj fakty, fake newsy i zadaj pytania ekspertom.
-
Degradation of modified TPS in natural and industrial compost
PublicationThe aim of the study was to determine in the pilot studies the degree of decomposition of modified by us thermoplasic starch (potato starch).Commercial and new obtained by us foils were tested in an open roofing at normal weather conditions. The most visible changes were observed in TPS modified by epoxidized soybean oil and arabic gum contrary to commercial foils where there was no mass change observed.
-
Current status and future success of renewable energy in Pakistan
PublicationMismatch between energy demand and supply from last two decades has been increasing because of the domination of expensive imported oil in energy mix of Pakistan. To import crude oil Government paid US $ 9 billion in 2008–2009 to meet the energy demands...
-
Effectiveness of a dual surface modification of metallic interconnects for application in energy conversion devices
PublicationA dual surface modification of an SOFC metallic interconnect with a Gd2O3 layer and an MnCo2O4 coating was evaluated. The tested samples were oxidized for 7000 h in air at 1073 K. Oxidation products were characterized using XRD, SEM-EDS, and confocal Raman imaging, and ASR was measured. The effect of gadolinium segregation at grain boundaries in Cr2O3 was evaluated using S/TEM-EDS. Area specific-resistance was measured and fuel...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublicationThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
TEST METHOD FOR DETERMINING THE CHEMICAL EMISSIONS OF A MARINE DIESEL ENGINE EXHAUST IN OPERATION
PublicationThe article briefly describes the problem of air pollution caused by sea-going ships and the resulting restrictions on the emission of toxic and harmful chemical compounds in the exhaust of marine engines, introduced by the International Maritime Organization (IMO) under the International Convention for the Prevention of Sea Pollution from Ships (MARPOL 73/78). Such emissions provide a significant metrological problem, not only...
-
Exsolution of Ni nanoparticles on the surface of cerium and nickel co-doped lanthanum strontium titanate as a new anodic layer for DIR-SOFC. Anti-coking potential and H2S poisoning resistance of the prepared material
PublicationThe aim of this study was to evaluate a new catalytic material for biogas fueled DIR-SOFC. This material was a perovskite-type SrTiO3 doped with La, Ce and Ni of a general formula La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-σ (LSCNT). Additional preparation steps were undertaken to promote a nickel exsolution process. Heat post-treatment of powders in a humidified H2 resulted in an intensive growth of nickel nanoparticles (NPs) while the temperature...
-
Improving operating efficiency of a gas turboset via cooperation with an absorption refrigerating machine
PublicationThe analysis of increase of ambient air temperature entering the compressor on reduction in power output from the turbine and increase fuel use was conduced. For medium size gas turbine operates in winter and summer conditions elementary power and economical values was calculated. Conditions of the determination of turbine inlet air cooling solution (using thermal storage for reduce equipment size) are presented
-
Selected Problems of Cogeneration Energy Systems Designing, Fueled with Landfill Biogas
PublicationThe article discusses the impact of the quality of biogas fuel for operation of generating sets with internal combustion engines. There are presented selected investigation results of landfill biogas fueled gensets operation. The article includes also discussion of the possibility of increasing the efficiency of biogas fuelled cogeneration systems. It also presents guidelines for the optimal design of landfill biogas fueled engines,...
-
Research on flue gas flow measurement and modelling in the moving grate biomass boiler
PublicationThe aim of this research was to determine the nature of gas flow in a grate boiler model by the method of Particle Image Velocimetry (PIV) and CFD. The paper presents the comparison of the PIV results with numerical simulations made in the environment of ANSYS Fluent. The main goal of the experiment was to describe the phenomena occurring on the grate. Methodology of modelling solid fuel combustion on the moving grate was proposed...
-
Thermogravimetric analysis/ pyrolysis of used tyres and waste rubber
PublicationThe process of pyrolysis is investigated in this paper. The pyrolysis results of two samples: waste tyres and rubber at different heating rates (10, 20, 50 K/min), were compared. In other experiments the degradation of two pyrolysis products, char and oil was examined. The kinetic study using the thermogravimetry equipment (TG) was done, which allowed determination of the kinetic mechanism of the process. The elemental analysis...
-
Accumulation of volatile constituents in agar and bioreactor shoot cultures of Verbena officinalis L.
PublicationIn vitro shoot cultures of common vervain (Verbena officinalis L., Verbenaceae) were established and evaluated for essential oil content. The shoots were maintained as stationary microshoot culture, grown on Schenk–Hildebrandt medium supplemented with 9.84 µM of 2-isopentenyladenine and 1.0 µM of thidiazuron. The shoots were further adapted to grow in two temporary immersion bioreactors (RITA and Plantform), using Schenk–Hildebrandt...
-
SIMPLIFIED MODELING OF STRESS AND DEFLECTION LIMIT STATES OF UNDERGROUND TANKS
PublicationFuel tanks are designed with regard to standard actions and operating conditions. The work analyses the impact of corrosion and other means to variation of stresses and deformation of a horizontal underground tank shell. The computations are preliminary. Due to the long computational time of the entire tank the analysis is restricted to its part only. The full analysis is bound to assess structural reliability, further allowing...
-
Possibilities of the performance improvement of the aero- and marine propulsion units equipped with combustion piston engines
PublicationWithin the paper there have been presented the authors' opinions concerning possibilities and needs of the performance optimization of the aero- and marine units powered by piston engines both of ''classic'' and contemporary construction. There have been also discussed the reserves contained within combustion piston engines which enable its performance improvement (the power and specific fuel consumption) as well as the fulfillment...
-
Effects of liquid phase modification on the values of surface tension of trickling liquid
Open Research DataDataset presents the values of surface tension of trickling liquid sampled from three running biotrickling filters.
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublicationBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
Market Price Prediction of Property Rights from Gas Fired Plants or Plants with Total Installed CHP Source Capacity Below 1 MW until 2025
PublicationThe resolution on the Polish Energy Policy until 2030 (PEP-30) was adopted by the Council of Ministers on 10 November 2009. The document specifies the combined electricity and heat generation as a direction of pursuing the goals of energy efficiency, fuel and energy supply security, competitive fuel and energy markets development, and reduction of the energy sector’s environmental impact. PEP-30 assumes that electricity generation...
-
Hydrogen production from ethanol In nitrogen microwave plasma At atmospheric pressure
PublicationHydrogen seems to be one of the most promising alternative energy sources. It is a renewable fuel as it could be produced from e.g. waste or bio-ethanol. Furthermore hydrogen is compatible with fuel cells and is environmentally clean. In contrast to conventional methods of hydrogen production such as water electrolysis or coal gasification we propose a method based on atmospheric pressure microwave plasma. In this paper we present...
-
High performance LaNi1-xCoxO3-δ (x = 0.4 to 0.7) infiltrated oxygen electrodes for reversible solid oxide cells
PublicationOxygen electrodes prepared by infiltration of yttria stabilized zirconia backbone with Ce0.8Gd0.2O1.95 barrier layer and LaNi1-xCoxO3-δ (x=0.4 to 0.7) catalyst for application in reversible solid oxide cells have been studied. The effect of temperature and Ni:Co ratio on their phase composition, microstructure and electrochemical properties are discussed. It was shown that oxygen electrodes infiltrated with LaNi0.5Co0.5O3-δ had...
-
Diagnostic Model of Crankshaft Seals
PublicationT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
The effect of paleo-environment on hydrocarbon generation potential: Example from Vaca Muerta Formation, Neuquén Basin, Argentina
PublicationA 137-m continuous core from the Jurassic-Early Cretaceous marine derived oil shale with the maturity Ro about 0.7 %, representing the oil window in the Vaca Muerta Formation, Neuquén Basin, Argentina, was examined using geological, mineralogical, petrographic, and geochemistry techniques. Three distinct intervals were identified within the core: the upper carbonate-rich section with intense bioturbation, indicating dysoxic to...
-
THE PROBLEM OF AIRFLOW AROUND BUILDINGS CLUSTERS IN DIFFERENT CONFIGURATIONS
PublicationIn the paper, the authors discuss the construction of a model of an exemplary urban layout. Numerical simulation has been performed by means of a commercial software Fluent using two different turbulence models: the popular k-ε realizable one, and the Reynolds Stress Model (RSM), which is still being developed. The former is a 2-equations model, while the latter – is a RSM model – that consists of 7 equations. The studies have...
-
A simplified method to assess the impact of ship-to-ship collision on the risk of tanker ship hull girder breaking accounting for the effect of ageing
PublicationOne of the most critical structural failures is the exceedance of the ship hull girder’s ultimate strength, which may result in hull breaking, and subsequent severe consequences, including loss of life and property as well as environmental damage in case of an oil spill. A cause for such loss of structural continuity can be triggered by a collision with another vessel. In addition, the ageing mechanisms of the hull structure could...
-
Alternative Energy: Photovoltaic Solar Cells
PublicationSolar radiation is a fuel for photovoltaic cells and modules, which are a source of electric energy. Viable solar technologies that have been developed in the past are starting to be adopted on a broader and more meaningful global scale across different sectors with ever-increasing market penetration. In this entry, a brief overview of the material properties relevant to solar cell operation, the structure of the solar cell, and electrical...
-
High-efficient, zero-emission energy production
PublicationThis paper presents innovative thermodynamiccycles with high-efficient, zero-emission energy production. The main aim of this work is to show the role of nano-phenomena in the enhancement of the power of thermodynamic cycles. For that purpose, the cycles using oxy-combustion and spray ejected condensation are first studied and, secondly hybrid cycles using fuel cells and gas turbines are presented. The role of nano-phenomena in...
-
The use of spectrometric diagnostics in identification of the technical condition of tribological systems
PublicationThe paper presents, as an effect of the analysis of investigation results, a possibility of using the spectrometric diagnostics in the tribological system technical condition supervision arrangement. A model, based on the emission of solid particles in tribological system operation, allows to identify the system technical condition. After the analysis of tests carried out with the use of that model, it has been found that the content...
-
Ontologia usług sieciowych OWL-S.
PublicationRozwijająca się dziedzina agentów i usług sieciowych dojrzała do wypracowania standardów zapewniających wspólny sposób opisu, wywoływania i nadzoru wykonania tych serwisów. Propozycja takiego standardu jest opisywana w rozdziale ontologia OWL-S, bazująca na założeniach sieci sematycznej i będąca rozwinięciem oraz uporządkowaniem wcześniejszej propozycji znanej pod nazwą DAML+OIL oraz DAML-S.
-
Low and high energy explosive materials used in shale gas recovery
PublicationNowadays the explosives are widely used in many areas of life, including industry and mining. A wide range of explosive materials is used in the petroleum industry - from low to high explosives. Recently, as the unconventional oil and gas production became possible, explosives are also found to be used in perforators during the pre-completion stage of the fracturing process. This paper presents literature on theoretical and practical...
-
Inżynieria odwrotna bazy paliw płynnych w Gdańsku
PublicationArtykuł prezentuje prace z zakresu pozyskania danych o zbiornikach bazy paliw płynnych w Gdańsku. Przedstawione rozwiązanie nie ogranicza się tylko do stworzenia (rejestracji) chmury punktów, ale jest próbą wskazania użycia naziemnego skaningu laserowego do stworzenia bazy informacji o bazie paliw – w tym głównie geometrii zbiorników. Autorzy prezentują proces inwentaryzacji, rejestrację chmury punktów oraz wskazują zasady tworzenia...
-
Decreasing CO2 Emissions By Reducing Tire Rolling Resistance
PublicationThe first motor vehicle was built by Nicolas Cugnot almost 250 years ago and since then there has been a continuous process of motor vehicles’ improvements, as well as development of new road pavements. The fuel crisis of the 70s of the 20th century made it clear to vehicle builders that measures should be taken to reduce vehicle fuel consumption and it contributed to an increased interest in electric vehicles. Although significant...
-
Model matematyczny strat objętościowych ściskania oleju hydraulicznego w pompie wyporowej o zmiennej wydajności
PublicationCelem pracy było stworzenie możliwości oceny strat objętościowych wynikających ze ściskania oleju hydraulicznego w komorach roboczych wysokociśnieniowej pompy wyporowej o zmiennej wydajności na obrót wału. Straty objętościowe ściskania oleju muszą być określone jako funkcje tych samych parametrów, w zależności od których ocenione są straty objętościowe przecieków oleju w komorach, wynikające z jakości rozwiązania konstrukcyjnego...
-
Spatial Aspects of Tram and Trolleybus Supply System
PublicationNowadays the issue of electric energy saving in public transport is becoming a key area of interest which is connected both with a growth in environmental awareness of the society and an increase in the prices of fuel and electricity. It can be achieved by reducing of the transmission losses in supply system or by the improving of the usage of the regenerative breaking. The spatial differentiation of the energy supply system of...
-
MEASUREMENT AND ANALYSIS OF TRANSMISSION LOSSES IN THE SUPPLY SYSTEM OF ELECTRIFIED TRANSPORT
PublicationThe issue of electric energy saving in public transport is currently becoming a key area of interest, a fact connected with both an increase in society’s environmental awareness and a rise in the prices of fuel and electricity. Electricity can be saved by reducing transmission losses in the supply system. The article presents a method of measurement and analysis of transmission losses in the supply system of electrified public transport...
-
Comparison of soil models in the thermodynamic analysis of a submarine pipeline buried in seabed sediments
PublicationThis paper deals with mathematical modelling of a seabed layer in the thermodynamic analysis of a submarine pipeline buried in seabed sediments. The existing seabed soil models: a “soil ring” and a semi-infinite soil layer are discussed in a comparative analysis of the shape factor of a surrounding soil layer. The meaning of differences in the heat transfer coefficient of a soil layer is illustrated based on a computational example...
-
Aleksander Mroziński dr inż.
PeopleAleksander Mroziński is a PhD student at the Faculty of Electronics, Telecommunications and Informatics of the Gdańsk University of Technology. From June 2019 is employed as a metadata editor in the project THE BRIDGE OF DATA. He also participates in three other projects implemented at the Gdańsk University of Technology: InterPhD II, OPUS 13 and PROM. His desire to discover the world motivates him to acquire multidisciplinary...
-
Exergy analysis of a negative CO2 emission gas power plant based on water oxy-combustion of syngas from sewage sludge gasification and CCS
PublicationA power cycle with water-injected oxy-combustion (water cycle) is investigated by exergy analysis. It is fueled with syngas (aka. producer gas) from gasification of sewage sludge. The cycle is equipped with a spray-ejector condenser (SEC). CO2 is separated and compressed for transportation and storage. The net delivered electric power is 31% of the fuel exergy. The task efficiency is 39% when the flue gas bleed to gasification...
-
Performance of cryogenic oxygen production unit with exhaust gas bleed for sewage sludge gasification and different oxygen purities
PublicationThe paper presents a thermodynamic analysis of the integration of a cryogenic air separation unit into a negative CO2 emission gas power plant. The power cycle utilizes sewage sludge as fuel so this system fits into the innovative idea of bioenergy with carbon capture and storage. A cryogenic air separation unit integrated with the power plant was simulated in professional plant engineering and thermodynamic process analysis software....
-
CREATING A RANKING OF DIAGNOSTIC PARAMETERS FOR THE DYNAMIC PROCESS OF A MARINE COMBUSTION ENGINE IN THE ASPECT OF MULTI-CRITERIA EVALUATIONS
PublicationThe change of some of the engine’s structural parameters affects the change of toxic compound emission in exhaust gases. It mainly applies to the damage sustained by the charge exchange system as well as the fuel system and the engine supercharging system. These changes are definitely higher during dynamic states and the related transient states. As such, it is possible to speak of a diverse sensitivity of the diagnostic parameters...
-
A new method for real-time monitoring of volatiles in frying fumes using proton transfer reaction mass spectrometry with time-of-flight analyse
PublicationTo safeguard the consumers’ well-being, it is necessary to develop novel methods for determination of carcinogens in food, including volatiles generated during frying. The currently used procedures for analysis of volatile fraction of vegetable oils are not based on real-time measurements and thus do not enable the determination of carcinogenic compounds in frying fumes; instead, only the headspace or liquid fraction is sampled....
-
Korozja w środowisku ropy naftowej. Czynniki i monitorowanie
PublicationPrzedstawiono analizy właściwości ropy naftowej z punktu widzenia zawartych w niej czynników korozyjnych oraz ich wpływu na korozję stali w trakcie procesu destylacji ropy naftowej. Krytycznej analizie poddane zostały możliwości oferowane przez współczesne techniki pomiarowe. Wskazano na istotność prowadzenia kompleksowego programu oceny ropy, monitorowania korozji oraz stosowania ochrony inhibitorowej w celu ochrony instalacji...
-
Strucutral steel - tensile test results
Open Research DataModern floating structures such as ships, oil platforms and offshore wind towers are built mostly of structural steel. It is a material that is subject to requirements which, when met, allows the construction and safe operation of the structure throughout its entire work cycle. One of the basic criteria that a material must meet is its strength. The...
-
Reliability of production machines in the bakery industry – theoretical and practical issues
PublicationThe aim of the article is to present probabilistic models, which were then used to analyze the reliability of production machines in the baking industry. The author conducted research in the period from January 2, 2016 to December 31, 2018 regarding the measurement of reliability of a traditional production system based on a probabilistic concept. Due to the limited scope of the article, reliability calculations for a set of thermo-oil...
-
Large Hydrodynamic Thrust Bearings and Their Application in Hydrogenerators
PublicationLarge hydrodynamic thrust bearings are the bearings which, due to hydrodynamic lubrication, allow large axial load to be transferred from a moving part (shaft) to the stationary part via a thin layer of the lubricant (usually oil), thus providing extremely low friction and practically no wear. Hydrogenerators with vertical shafts are the most important application of large thrust bearings. Main design and scientific problems of...
-
Effect of alkyl sulfate on the phase behavior of microemulsions stabilized with monoacylglycerols
PublicationIn this study the effect of an anionic surfactant (sodium dodecyl sulfate SDS) and oils (hydrocarbons: C12-C16) on the formation and phase behavior of the systems of oil/monoacylglycerols (MAG):SDS/propylene glycol/water has been investigated. The effects of the surfactant mixture on the phase behavior and the concentrationof water or oil in the systems were studied at three temperatures (50, 55, 60 C). Electrical conductivity...
-
Protection and viability of fruit seeds oils by nanostructured lipid carrier (NLC) nanosuspensions
PublicationIn this paper, we focused on the development of nanostructured lipid carriers (NLCs) for dermal application. The NLC matrix was designed as a protective reservoir of biological active compounds that naturally occur in domestic fruit seed oils. Over the years, emulsions, as a popular physicochemical form of personal care products, were refined in order to obtain the best possible penetration into the skin of any bioactive compound...
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationNonstoichiometric Nb-substituted SrTiO3 compounds were investigated in order to discuss the influence of nonstoichiometry at the sample properties in the light of recent results reported in the literature. Structural and electrical properties of samples were characterized. Investigated compounds were also applied as anodes for Solid Oxide Fuel Cells and their reactivity with YSZ electrolyte was examined. The defect chemistry explaining...
-
Analytics of airport runoff water samples
PublicationThe everyday activities at airports, such as aircraft and ground vehicle washing, cleaning, de/anti-icing operations, fuelling, and fuel combustion, removing weeds are the main sources of airport industrial wastes. Runoff waters from airport areas constitute a serious environmental problem as they contribute to air, water, and soil pollution. The paper supplies general information on the technologies for treating airport runoff...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublicationThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
Efficiency of Biomass Energy used for Heating Purposes in a Residential Building in Comparison with other Energy Sources
PublicationThis paper discusses the results of analyses investigating the energy efficiency of biomass in comparison with other popular energy carriers used for heating, ventilation and water heating in residential buildings. The compared energy sources were lignite, natural gas, heating oil and electricity produced by conventional and integrated power generation plants. The most efficient variant relying on biomass and the least efficient...
-
Identification of aromatic compounds in odours mixture by gas chromatography and field olfactometry techniques
PublicationThis paper shows the results of investigation on identification aromatic compounds present in odorous mixture in atmospheric air samples collected in a vicinity of the oil refinery LOTOS S.A., located in Gdansk, during March and April period have be presented. The studies were conducted by the use of comprehensive two-dimensional gas chromatograph equipped with a cryogenic modulator and coupled with a time-of-flight mass spectrometer,...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Spalanie w cementowniach jako forma odzysku energetycznego opon
PublicationCombustion in cement mills as a form of energy recovery from tiressummary: the subject of used tires is an important issue in poland. in this article, special focus is aimed atmaterial recycling, i.e. tire burning. even though this is not the most energetically effective method, it is one ofthe main techniques used in tire utilization. tires are burned as alternative fuel in already existing cement mills.the high calorific value...
-
SMART GRID TECHNOLOGIES IN ELECTRIC POWER SUPPLY SYSTEMS OF PUBLIC TRANSPORT
PublicationNowadays the issue of electric energy saving in public transport is becoming a key area of interest which is connected both with a growth in environmental awareness of the society and an increase in the prices of fuel and electricity. It can be achieved by reducing of the transmission losses in supply system or by the improving of the usage of the regenerative breaking. The article presents an analysis of applying these two options...
-
SMART GRID TECHNOLOGIES IN ELECTRIC POWER SUPPLY SYSTEMS OF PUBLIC TRANSPORT
PublicationNowadays the issue of electric energy saving in public transport is becoming a key area of interest, which is connected both with a growth in environmental awareness of the society and an increase in the prices of fuel and electricity. It can be achieved by reducing the transmission losses in a supply system or by the improving the usage of the regenerative breaking. The article presents an analysis of applying these two options...
-
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
PublicationVarious types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublicationIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...